PROVIDING AIR CONDITIONERS IN COMMUNITY CENTRE, SEC 25, CHANDIGARH.

Supplying, installation, Testing and Commissioning of Split Type AC 2.0 Ton, 3 Star Rating. The AC shall be Suitable for 230 +/- 10% volts, 50 Hz Ac supply. The AC EER not less than 3.55 supply with Copper condenser. 2.0 Ton Capacity of nominal cooling capacity 6000 kilo calories/Hr./24000 BTU/Hr. with permissible variation of +/- 10%. Room discharge air flow 650 cfm indoor Nosie level not exceed 50 db. Refringent R-22/410 A. Including copper piping/ Electrical wire between indoor & outdoor upto four meter with sleevein type insulation I/C cost of M.S brackets/ stand for outdoor until as per manufactures standard and complete to the entire satisfaction of Engineer-in-charge. Make:Carrieer/Voltas/Hitachi/Daikin/Mitsubishi with warranty of 3 years.

Supplying, installation, Testing and Commissioning of Split Type AC 1.5 Ton, 3 Star Rating. The AC shall be Suitable for 230 +/- 10% volts, 50 Hz Ac supply. The AC EER not less than 3.55 supply with Copper condenser. 1.5 Ton Capacity of nominal cooling capacity 4500 kilo calories/Hr./18000 BTU/Hr. with permissible variation of +/- 10%. Room discharge air flow 650 cfm indoor Nosie level not exceed 50 db. Refrigent R22/410 A. Including copper piping/ Electrical wire between indoor & outdoor upto four meter with sleevein type insulation I/C cost of M.S brackets/ stand for outdoor until as per manufactures standard and complete to the entire satisfaction of Engineer-in-charge. Make: Carrieer/Voltas/Hitachi/Daikin/Mitsubishi with warranty of 3 years.

Supplying and fixing voltage stabilizer 5 KVA for AC of 2 Tn and above with MCB, TDR volt meter copper winding input range 180-250 volt single phase including cost of copper wire from stabilizer to A.C unit with M.S body of 22 gauge sheet powder coated). Cost includes 15A plug top. Make Deol/Jewel/ V-Guard with warranty of 2years.

Supplying and Fixing Voltage stabilizer 4 KVA for AC upto 1.50 TR with MCB, TDR volt meter copper winding input range 180–250-volt single phase including cost of copper wire from stabilizer to A.C unit with M.S body of 22 gauge sheet powder coated). Cost includes 15A plug topMake Deol/Jewel/ V-Guard with warranty of 2years.

Providing and fixing of 28 gauge copper piping between indoor & outdoor unit complete with sleeve type Kini insulation including the cost of chasing of brick wall, RCC & repairing the same in good conditions as per site requirement to the size & design of manufacture.

size of copper pipe 5/8"x3/8".

Providing & Fixing PVC rigid drain pipe 20mm (3/4") dia of Diplast/ finolex/supreme make of complete in all respects from indoor unit to disposal points as directed by EIC.

Providing and fiixing flexible copper conductor wires complete in all respects. Make Finolex/Polycab/Havells/BCH or its equivalent ISI marked 3 core 2.5 mm.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. ISI marked.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) of make L&T/ Havells/ ABB/Schneider 6 way (4 + 18), Double door.

Supplying and Erection of DP 32 amps. rating, 240 volts, 'C' series, miniature circuit breaker suitable for inductive load of following poles alongwith enclosure MCB DB complete with connections, testing & commissioning etc. as required Double Pole 32 Amps L&T/Havells/ABB/Schneider Make.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single Pole of make Havell's/ Standard/ABB/L&T/Schneider.

Supply and fixing of three phase MCB TPN 100 Amp complete to the entire satisfaction of engineer-in-charge. The MCB TPN is to be fixed inside the existing Distribution Box. Make: HavellS/ Standard/ ABB/L&T/Schneider.

Wiring in existing conduit: Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/recessed steel/ PVC conduit as required. ISI marked

Size 3x2.5sq.mm

Size 3x4 sq.mm

The M.S. angle iron board covered with 16 GMS sheet fixed in to the nitch for mounting switch gear. The switches /BDB’s / ELCB/bus bar shall be provided with required no. of supporting member of M.S. flat 25mm5mm to bring all the switchgear in one level including bonding the board switchgear etc. to the existing earth. The board shall be fabricated out of 40mmx40mmx5mm angle iron frame and shall be covered with a 16 GMS sheet duly welded for erection of switchgear items on it. The board shall be painted with two coat of approved shade of superior quality paint after one coat of primer. The rate includes carriage from factory to site, erection charges in the niche and other petty material required at site of work.

Fabrication & erection of steel shutters for electrical niches as per following specifications FRAME: The shutter of suitable dimensions for electrical nitch shall be made out of 16 G.M.S. sheet. The shutter frame shall be 1-1/2”x1-1/2”x1-1/2” channel frame 4 Nos. ‘L’ type holdfasts for fixing the same on the wall. The size of the shutter frame should be suitable for 2Nos. door panels/single panel depending upon the size of nitches DOOR PANEL: The door panel shall have support in U-Shape formation made from 16G.M.S. sheet with 4”x3/4”M.S. channel duly spot welded to give additional strength. The door panel shall be fixed with frame with the help of concealed M.S. hinges of suitable size having good strength. The door panel shall be provided with a bolting arrangement either of Godrej type or such type so as to interlock the door panel with frame. The handle shall be of superior quality and nickel plated to facilitate its opening. The door panel must have as arrangement to provide a pad lock. FINISHING: The frame & the door panel should be given anti-rust, anti-grease and phosphate treatment with 3 in 1 paste and then spray painted with two coats of paint of superior quality. The shutter should be earthed properly with the existing earth with No.8SWG wire after erasing the paint from the body of the Shutter. The rate includes cost of all labor and material reqd. to complete the job to the satisfaction of the Engineer-in-charge.

Providing and fixing of 100 Amp 415 volts Bus bar chamber of tin plated copper strip of size 350mm*450mm*150mm of make Asco/L&T/Havells/ABB/Schneider. The rate includes cost of all labor and material reqd. to complete the job to the satisfaction of the Engineer-in-charge.

Please Enable Macros to View BoQ information