ADDITION/ALTERATION AND SPECIAL REPAIRS OF MD ACCN AT BABINA CANTT.

Amount

Note: (i) Please refer schedule 'A' notes before quoting the tender. (ii) Amount of Schedule of credit shall be deducted off line by the department.

Demolition of existing roof treatment of any description and in any position complete with APP membrane and 10mm thick backing coat below APP membrane complete all as specified and directed.

Dismantling of 500 litres PVC water tanks from any position complete all as specified and directed.

Demolition of PCC in any description and in any position etc complete all as specified and directed.

Taking down cement plaster on brick or stone wall including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) exe 1.5 Sqm but n exc 4 Sqm each etc complete all as specified and as directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) not exe 1.5 Sqm each.complete all as specified and directed.

Taking down shutters of any description exc 1 sqm and n.exc 2 Sqm each complete all as specified and directed.

Taking out old unserviceable glass panels of any description from old wooden or metal frames or stones, concrete or brick surrounds, any thickness or size; hacking out old putty or removing beads etc. including making good breakages in taking out and S & F 3 mm thick sheet glass, Ordinary quality and glazing with putty or fixed in existing window, area of each pane not exc 0.5 Sqm in each panel complete all as specified and as directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC/PVC/CI or Reinforced concrete), 100mm bore, set in cement mortar in floors or walls complete all as specified and directed.

Demolition of brick work built in cement mortar complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floore aprons etc laid bedded and pointed in any mortar complete all as specified and directed.

Demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provide for complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete), 150mm bore, set in cement mortar complete all as specified and directed.

M & L for Preparation of new plastered surface of wall and applying two coats of Oil bound distemper over a coat of chalk whitening as primer complet all as specified and as directed

M and L for preparation of new plastered surface of wall and applying two coats of cement base paint on external wall surface complete all as specified and directed.

M & L for complete removal of existing treatment from surface of wall and applying two coats of oil bound distemper complete all as specified and as directed.

M&L complete removal of existing treatment & preparing old decorated surfaces of wall but and applying two coats cement base paint all as specified and as directed.

M&L for non skid coloured joint free ceramic tiles 7 to 8 mm thick (square/rectengular) area of each tile exceeding 0.11sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to floor etc including 15 mm screed bed with CM(1:4) and 25 mm thick PCC(1:2:4) type B-0 complete all as specified and as directed.

M&L for non skid coloured joint free ceramic tiles 7 to 8 mm thick (square / rectengular) area of each tile exceeding 0.11sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to floor etc including 15 mm screed bed with CM(1:4) complete all as specified and as directed.

M&L for non skid coloured joint free ceramic tiles 7 to 8 mm thick (square / rectengular) area of each tile exceeding 0.06sqm but not exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to floor etc and including 15 mm screed bed with CM(1:4) and 25 mm thick PCC(1:2:4)type B-0 complete all as specified and as directed.

M&L for non skid coloured joint free ceramic tiles 7 to 8 mm thick (square / rectengular) area of each tile exceeding 0.06sqm but not exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to floor etc and including 15 mm screed bed with CM(1:4) complete all as specified and as directed.

M&L for non skid coloured joint free ceramic tiles 7 to 8 mm thick (square / rectengular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm, in Skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match to tiles etc and including rendering 10mm thick rendering on fair faces of wall or concrete surfaces in CM 1:4 finished rough to receive wall tiling etc complete all as specified and as directed.

M&L for joint free glazed coloured tiles 300x200x7mm thick for work on vertical surface, set & jointed in cement slurry and pointed in white or coloured cement to match etc including rendering 10mm thick on fair faces of wall or concrete surfaces in CM 1:4 finished rough to receive wall tiling complete all as specified and as directed

M & L for preparation of new plastered surface and applying three coats of white wash on ceiling complete all as specified and as directed.

M&L for precast machine pressed cement concrete tiles of size 25cm x 25cm x 22 mm thick (with grey cement and no pigment) laid in neat cement slurry over and including 15 mm thick cement mortar screed in 1:4 and joints between the tiles to be filled with grey cement complete all as specified and directed.

M&L, rendering 5mm thick in cement mortar 1:3 on ceiling surface and finished even and smooth with out using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick/concrete surfaces of walls, finished even and smooth without using extra cement complete all as specified and as directed

M&L for 10 mm thick rendering in cement mortar 1:4 on concrete surfaces when concrete is still green finished even and fair including mixing of water proofing compound as per manufacturer's instruction complete all as specified and as directed. Note :- Supply only Water proofing compound shall be measured and paid separately.

M&L for rendering 10mm thick in CM 1:6 on fair faces of concrete or brick surfaces of walls, finished even and smooth without using extra cement complete all as specified and as directed

Supply only integral water proofing compound complete all as specified and as directed.

M&L for plain cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate for coping/plinth of poles, including necessary form work, surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregates) as in foundation filling and mass concrete including form work for poles/fencing pillers/ mass concrete complete all as specified and directed.

M&L for P.C.C 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in padding over roof, finished and laid to required slope complete all as specified and as directed.

M&L for 40mm thick cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) surface finished even & smooth w/o using extra cement complete all as specified and as directed.

M&L for 75mm thick cement concrete type C-1, 1:3:6 (20mm graded aggregate) as in plinth protection finished even and smooth without using extra cement complete all as specified and as directed.

M&L PCC 1:3:6 type C-1 (using 20mm graded stone aggt) as in filling in holes of hold fasts complete all as specified and as directed.

Cutting grooves in brick wall 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed.

M&L for water proofing treatment with the followings:- (a) First coat of bitumen primer conforming to IS-3384 @ 0.3Kg / sqm to be applied on prepared surface till the surface is properly impregnated. (b) after the application of approved bituminous primer the water proofing memberne minimum weight 3kg/sqm and minimum 3mm thick reinforced with polyesterd non woven fabric (weight not less then 150gms/sqm) shall be laid on the primed surface by torch application method as per manufactured instruction. (c) All joints and change in direction should be curved with cement mortar (1:3) mixed with SBR latex @ 200ml per bag on cement and cured well before laying of membrane complete all as specified and directed..

Taking up or down existing steel tubing and connections including cleaning for refixing complete all as specified and as directed for the following sizes:-

(a) 15 mm bore

(b) 20 mm bore

Supplying, fixing, jointing and testing galvanised iron tubing medium grade with all fitting such as bends, elbow, socket, reducer etc and fixed to wall or laid in floor complete all as specified and as directed for the following sizes:-

(a) 15 mm bore

(b) 20 mm bore

Fixing only old steel tubing and connections (obtained from taking down) in new or old position fixed to wall, ceiling or laid in floor with new fittings for the following sizes:-

(a) 15 mm bore

(b) 20 mm bore

S&F, 500 litres Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

S&F, 20mm bore ball valve high pressure of PTMT (Minium weight 210 gms ) with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and directed

S&F, in repair, 20mm bore Gun metal gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

M&L for 38mm wide and 3mm thick glass dividing strips complete all as specified and as directed.

M&L for 25mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15 mm thick in CM (1:6) etc complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck in side with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail,paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement all as directed and specified and directed.

S & F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube etc complete. complete all as specified and directed.

S&F aluminum anodized barrel tower bolts of extruded section & fixed 150 mm long etc complete all as specified and as directed

S&F aluminum handles cast type anodized 150 mm size etc complete all as specified and as directed

S&F, 150mm floor door stopper aluminium alloy body complete all as specified and directed.

S & F butt hinges medium weight cold rolled, mild steel and fixed 100 mm size etc complete all as specified and directed.

S&F but hinges extruded aluminium alloy with galvanised mild steel hing pin, anodised and fixed, type C-21 100 mm size in toilet with PVC doors etc complete all as specified and directed.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy complete all as specified and directed.

Cutting holes in brick walls built in cement mortar for inserting hold fasts depth exc half brick but not exc full brick wall and making good dismantled portion in CM 1:3 or cement conc 1:2:4 type B1 as required complete all as specified and directed.

S&F, mild steel flat iron 25x3 mm as in hold fasts etc confirming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

S&F, framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete of Fe-410-W (Gde-E-250) complete all as specified and directed.

S&F, Pressed steel frames for doors (125x60) mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed etc complete all as specified and directed.

S&F, Pressed steel frames for doors (105x60) mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc supplied and fixed complete all as specified and directed.

M & L secound class hardwood Plain, solid, straight chowkats and frames wrought framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

S&F, 18/19 mm thick prelaminated particle board interior grade prelaminated one side with decorative choice laminations and other side balancing white lamination fixed with screws to timber frame work etc complete all as specified and directed.

S&F, 19 mm wide and 6mm thick Cover fillet of external teak wood lipping fixed with nail all as specified and directed.

S&F, Hasp & staple, 100mmsize, safety type, aluminium anodized with mild steel hing pin including bolt to hing plate and fixed with screws complete all as specified and directed.

S&F Continuous (piano) hinges, mild steel bright finish electrogalvanised, 20mm width of flap complete all as specified and directed.

S&F, 35mm thick 2nd class Hard wood paneled door shutter factory made (two panel) with lock rail and panel of 9mm thick BWP commercial ply wood, the size of rail and stile is as per IS 1003 (Part-I), Kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F, factory made, 35 mm thick IInd class HW glazed & skeleton shutters open rebated and prepared to receive glass gauge etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut & mitered beads for security glass/gauge etc. size of members of shutter as specified in SSR Pt I sec 8 Cl 8.20 (a), divided into squares with plain chamfered rounded, mitered and rebated sash bars etc complete all as specified and as directed

S&F, galvanized mild steel wire cloth 0.63 mm nominal dia of wire and average width of apertare 1.40 mm fixed with tinned tacks or galvanized wire staples complete all as specified and as directed

M&L two coat synthetic enamel paint over one coat of pink primer on new wooden surface of any description not otherwise described over 10 cm width or girth including preparation of surfaces complete all as specified and as directed

M&L one coat synthetic enamel paint on old wooden surface including preparttion of old surface of any description not otherwise described over 10 cm width or girth etc complete all as specified and as directed.

S&F of CRC sheet box type steel window with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed

S&F of CRC sheet box type steel window with steel handle, and steel peg stay, complete with out glazing bars, dovetailed or welded complete all as specified and as directed

S&F of CRC sheet box type steel ventilator with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed

S/F of CRC sheet box type steel ventilator with steel handle, and steel peg stay, complete with out glazing bars, dovetailed or welded complete all as specified and as directed

M&L framed work as grills, gratings, etc with ends of bars shouldered and/ or riveted into spikes; or forged into spikes, framed guard bars; barred iron doors and similar work confirming to Fe 290. Gd-E-165 complete all as specified and as directed

S&F, 3 mm thick sheet glass, Ordinary quality and glazing with putty in square n. exc 0.5 Sqm in each pane complete all as specified and as directed.

S&F, 3 mm thick Figured glass, pin head type and glazing with oil putty in squares in exc 0.5 sq.m in each pane complete all as specified and as directed.

S&F, in repair, vitreous china squatting pan “ORISSA” pattern size 58X44Cm, star white with P or S trap front or back inlet with integral foot rest (excluding flushing cistern & flush pipe) & including connection to trap & to flushing pipe anti syphonage pipe etc complete including making good to floor complete all as specified & as directed.

S&F, in repair, 10 ltrs capacity, PVC low level flushing cistern sleek plus single flush of colour star whire, with inlet, float valve and handle with 32 mm dia PVC pipe 600 mm long complete all as specified and as directed.

S&F, in repair, Vitreous China Wash hand basin white, flat back, size 550 x 400 mm size (flat back or angle back type) including cutting for and pinning ends of brackets or erecting stand and waste pipe complete all as specified and directed.

S&F, in repair, PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and as directed

S&F, in repair, 15mm bore Concealed stop Cock regular body with flange complete all as specified and as directed.

S&F, in repair, 15mm bore cast copper alloy chromium plated angle cock with flange complete all as specified and as directed.

S&F, in repair, 15mm bore fancy type chromium plated bib cock long body with flange etc complete all as specified and as directed

S&F brass CP mixer 15mm bore mixing hot & cold water for wash hand basin screwed down for iron pipe and fixed complete all as specified and directed.

S&F Cast Iron floor trap outlet dia 75mm with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S&F Cast Iron Nahani trap outlet dia 75mm with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S&F, in repair, Towel rail 450mm long of PTMT (Minimum weight 190gms), fixed with and including Chromium plated brass screws and wooden/plastic cleats complete all as specified and directed.

S&F, in repair, 125 mm Brass chromium plated shower rose with or without swivel joints, any size, including fixing of steel pipe or union and fixed complete all as specified and directed.

S&F, Grating doom 100 mm dia of PTMT (Minimum weight 25 gms) complete all as specified and directed.

S&F, stainless steel kitchen plate rack overall size 900mm x 900mm x250mm made out of 0.63mm thick stainless steel sheet etc complete all as specified and directed.

S&F, in repair, stainless steel sink with drainage board overall size 915x460mm with bowl size 410x330x160mm, 1.00mm thick, for kitchen or laboretory with plug, waste pipe, coupling, washers also including cantilever cast iron brackets connecting union etc complete all as specified and directed.

S&F, in repair, 25 mm dia chromium plate curtain rod with CP brackets and knobs at both end as per sample complete all as specified and directed.

S&F, 110mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall with clamp out of 25x3mm flat Iron including bolts and nuts complete all as specified and directed.

S&F, 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F, 75mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall with clamp out of 25x3mm flat Iron including bolts and nuts complete all as specified and directed.

S&F, 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F, PVC (SWR) bends any radius 110mm bore complete all as specified and directed.

S&F PVC (SWR) bends any radius 75mm bore complete all as specified and directed.

S&F PVC (SWR) junction single, (single T) equal or unequal 75mm bore with access door complete all as specified and directed.

S&F PVC (SWR) junction single, (single T) equal or unequal 110mm bore with access door complete all as specified and directed.

S&F PVC (SWR) vent cowl 110mm bore complete all as specified and directed.

M&L, Preparing old plastered/unplastered surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M&L, Preparing old plastered/unplastered surfaces of wall and applying one coat of white wash complete all as specified and directed.

M&L, Preparing old plastered/unplastered wall surfaces of wall and applying 3mm thick wall care putty complete all as specified and directed.

M&L, 60 mm thick machine pressed precast concrete interlocking paver block, M-35 grade with grey cement & pigment, any shape & size confirming to IS 15658-2006 complete all as specified and directed.

M&L, PCC 1:4:8 type D2 using 40mm graded stone aggregate as in filling and mass concrete, Sub base/flooring complete all as specified and directed.

M&L, Sand cushioing under interlocking paver block including watering & consolidation complete all as specified

M&L for brick work with fly ash bricks, straight or curved on plan exc 6 m mean radius built in CM (1:4) as in foundation of equipment, platform, protective wall of 1.5 mtr ht, supporting pillars of pipes complete all as specified and directed.

M & L rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work top surface finished even and smooth without using extra cement complete all as specified and directed.

M & L Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar (1:6) complete all as specified and directed.

Raking out joints/pointing to brick work in walls or to bricks on edge in floors, surface channels, roofs, etc. complete all as specified and directed.

M&L for Keyed pointing to brick masonry in CM 1:4 complete all as specified and directed.

S&F MS chromium plated peg set of five fixed on walls complete all as per sample and all as specified and directed.

M&L sand stone slabs in sunshades, chajjas, shelves, cills, landings, man hole cover, stones templates etc not exceeding 2m in length punched dressed on face and along exposed edges self faced on other side and set and pointed in cement mortar 1:4 thickness of slab 5cm complete all as specified and directed.

M&L for Formwork to chajjas, troughs and similar items including edges in flat for rough finished surface of concrete complete all as specified and directed.

M&L TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for TMT mild steel bars 6 mm to 8 mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire not less than 0.9mm dia or securing with clipscomplete all as specified and directed.

M&L for Desige mix M-25 RCC using 20mm graded stone aggregate in chajjas complete all as specified and directed.

M&L for 150mm internal dia Slat-glazed stoneware drain pipes, Grade Á' laid in trenches and joints complete all as specified and directed.

M&L for cement concrete type D-2 (1:4:8) bed to drain pipes including packing under, and hunching against the side of pipe after they are laid and tested for 150mm bore pipe complete all as specified and directed.

M&L, preparing for new steel surfaces and applying two coats of synthetic enamel paint over one coat of rex oxide primer over 10 cm width or girth complete all as specified and directed .

M&L, preparing for old steel surfaces and applying one coats of synthetic enamel paint over 10 cm width or girth complete all as specified and as directed.

Excavation in trenches in any type of soil not exe 1.5 mtrs wide and not exe 1.5 mtr in depth for laying of pipe/cables etc and getting out incl forming bottom surface to the required level/slope etc complete all as specified and directed .

Excavation in trenches in any type of soil not exc 1.5 mtrs wide and exc 1.5 mtr in depth but not exe 3.0 mtr depth for laying of pipe/ cables/ poles etc and getting out complete all as specified and as directed.

Excavating post holes or similar holes, each not exceeding 0.5 Cum, getting out in soft / loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50 metre and making good surface complete all as per specified and directed.

Returning, filling with excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50m and depositing where directed. at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M&L for fine and clean sand (river sand) free from sharp materials in trenches for cushioning of under ground cable etc including gently punning complete all as specified and directed. Note:- The total thickness of sand shall be measured after punning.

M&L for Soakage well of size 1.8 M dia X 3.0 M effective depth including excavation in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M-25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM (1:3), RCC cover slab in M-25, SFRC cover, interconnecting pipes of RCC/DWC, filled with brick bats all as specified and directed and as shown in Drg No. CEBZ/TD/78/2011 Sheet 1/1 & 1/2.

M&L for Septic tank for 100 users, designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, Brickwork in CM(1:3), RCC M-30 Design Mix in Baffle walls and Roof Slab including beams etc with Vent shaft, manhole openings with cover connection etc. complete all as specified and directed and as shown in Drg No. CEBZ/TD/76/2011 Sheet 1/1 & 1/2.

M&L for Septic tank for 50 users, designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, Brickwork in CM(1:3), RCC M-30 Design Mix in Baffle walls and Roof Slab including beams etc with Vent shaft, manhole openings with cover connection etc. complete all as specified and directed and as shown in Drg No. CEBZ/TD/76/2011 Sheet 1/1 & 1/2.

Taking down carefully aluminium/copper point wiring on batten or in PVC conduit or in MS conduit with GI earth wire etc (for light, fan, socket or power) complete including fixture and fitting such as switches, ceiling roses, pendents, regulators, sockets, light fitting etc. and making good the disturbed surfaces of walls, Floors, ceilings etc. complete all as specified and directed.

Taking down carefully existing wooden board, Main switch, MCB DB boxes with MCBs, sheet metal boxes, cut out, etc of any size any capacity from boards complete all as specified and as directed.

Taking down carefully sub main wiring / service connection twin core from wall / LT pole of any size of Aluminum with wooden batten and or through rigid conduit including GI wire and making good the disturbed surfaces of walls, roofs, floors etc complete all as specified and as directed.

M&L for concealed point wiring complete with PVC insulated and unsheathed flame retardant low smoke (FRLS) cable of 1.5 sqmm (nominal area) with stranded copper conductor single core 1100 volts grade in and including rigid PVC conduit ISI marked not less than 19 mm dia, clip with MS terminal boxes (not less than 1.0 mm thick) and painted with one coat of red oxide primer all around and two coats of black bituminous paint from out side and two coat of aluminum paint from in side including common earth dolly with 3 mm thick plastic laminated sheet top cover of approved make and colour including 1.5 sqmm green stranded copper conductor as continuous earth wire with lugs complete including cutting necessary chases on wall / ceiling surfaces for drawing of conduit & cables as required and making good disturbed surfaces of walls with CM (1:3) and matching with the existing surfaces including colour washing all as specified and as directed for the following :-

One light point controlled by one 5/6 amps one way switch.

One fan point/exhaust point controlled by one 5/6 amps one way switch & regulator.

One 3/5 pin 5/6 Amp socket outlet point controlled by one switch on independent board.

One 3/5 pin 5/6 Amp socket outlet point controlled by one switch on same board.

One bell/buzzer point controlled by one 5/6 Amps one way switch on same board.

All as per item No 143.00 above but using 2.5 sqmm single core multi stranded copper conductor PVC insulated and unsheathed flame retardant low smoke ISI marked (FRLS) cable for 3/6 pin 15 Amp socket outlet controlled by one switch on independent board with 2.5 sqmm green stranded copper conductor as continuous earth wire with lugs complete all as specified and as directed.

S&F, switch piano flush button type 5 Amp single pole one way duly marked with ISI grade complete all as specified and as directed.

S&F, socket outlet 2in1, 3 pin, 5 Amp flush type ISI marked complete all as specified and as directed.

S&F, switch piano flush button type 15 Amp single pole one way ISI marked complete all as specified and as directed.

S&F, socket outlet 2in1, 3 pin, 5 Amp and 15 Amp flush type ISI marked complete all as specified and as directed.

S&F, switch bell push button type 5 Amp single pole ISI marked complete all as specified and as directed.

S&F, Fan Regulator electronic rotary, step type 240 Volt 50 Hz ISI marked complete all as specified as directed.

S&F, Lamp holder,PVC/Urea type ISI grade with back plate suitable for batten fittings complete all as specified as directed

S&F, 9 W LED retrofit lamp B-22 holder base with polycorbonate body and aluminium heat sink pin type complete all as specified as directed.

S&F, ceiling rose, surface bakelite 63 x50mm three terminals ISI marked complete all as specified and as directed.

S&F, Bell, DING DONG AC 230Volts, single pole type complete all as specified and as directed.

S&F, Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps, 240 V 'C' series complete all as specified and as directed.

S&F for sub main wiring with PVC insulated, unsheathed, 2 single core cable FRLS grade 1100 volts grade with copper conductor of size 6.0 sq mm (Nominal area) multi stranded drawn into conduit (Existing / new) with and including 6.0 sqmm green stranded copper conductor as contineous earthwire with lugs complete all as specified and as directed. Note: Two runs of 6 sqmm main cables and one run of 6 sqmm cable of earth continuity conductor shall be measured and paid as one unit length. New conduit and conduit accossories shall be measured separately.

S&F, Rigid non-metallic PVC conduit not less than 32 dia (external), ISI marked (on surface) including all accessories and all fittings such as Tees, bends, elbows, reducers, bell mouth, tube ends and fixing accossories such as couplers, lock nuts, saddles, pipe hook etc complete all as specified and as directed

S&F, MCCB four pole, 415 volt, AC breaking capacity 16KA with fixed thermal and fixed magnetic setting of capacity 63Amp complete all as specified and directed.

S&F, MCCB four pole, 415 volt , AC breaking capacity 16KA with fixed thermal and fixed magnetic setting of capacity 100 Amp complete all as specified and directed.

S&F, MCCB sheet metal Enclosure box with hinged door suitable for housing 63A to 100 A MCCB four pole with provision for fixing arrangements on surface/wall, earthing terminal on body, hinged door with opening including suitable nuts, bolts & washer complete all as specified and directed.

S&F, sheet metal enclosure double door concealed suitable for distribution boards when MCBs to be used having 100 Amp rated bus bar 8 ways 240 V SPN ISI marked complete all as specified and as directed .

S&F, MCB single pole and neutral 63 Amp 240 V , 'C' series, complete all as specified and as directed.

S&F, MCB single pole and neutral 40 Amp 240 V , 'C' series, ISI marked complete all as specified and as directed.

S&F, MCB single pole 40Amps 240 V, 'B' series, ISI marked complete all as specified and as directed.

S&F, MCB single pole 6 to 32Amps 240 V, 'B' series,complete all as specified and as directed.

S&F, in repair, 20 W LED CCT 6000k having lumens efficiency of greater than or equal to 100 Lu/watt decorative ultra slim linear LED fitting fixture with extruded polycarbonate, environmental friendly, energy efficentinterated driver and 20 watts lamp fitted including wiring upto end terminal into existing ceiling rose complete all as specified and directed. Make - Bajaj Cat No BCLAB20W, White, VIVA led Mini LED batten (4Ft) or equivelent make as approved by GE from Appendix "C" List of Makes.

S&F, 9 W LED CCT 6000k having lumens efficiency of greater than or equal to 100 Lu/watt decorative ultra slim linear LED lighting fixture with extruded polycarbonate, environmently friendly, energy efficient with integrated electronic driver and 9W LED lamp fitted including wiring upto end terminal into existing ceiling rose complete all as specified and directed. Make - Havells Cat No LUMILINE BS9W LED 830SPCWH or equivelent make as approved by GE from Appendix "C" List of Makes.

Supply and fixing light fitting Energy saving new generation 10W LED IP65 bulkhead CCT 6000k having lumens efficiency of greater than or equal to 100 Lu/watt luminaire with opal diffuser including connecting electrically using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm complete all as specified and directed. Make - Havells Cat No LHEOAOP7UZ6W010 or equivelent make as approved by GE from Appendix "C" List of Makes.

S&F, decorative wall light fixture made of polycarbonate including LED Bulb 10 Watts with total lumens output not less than 900 lumens complete all as specified and directed. Make - Havells Cat No LHFHCH1TL1W020 (FLORET) or equivelent make as approved by GE from Appendix "C" List of Makes.

S&F, Ceiling fan, 3 blade high speed 1200mm sweep, BEE 5 star ratings, AC single phase 230 V including all arrangement like hook, down rod/pipe canopy of suitable size etc complete all as specified and directed.

S&F, Exhaust fan, AC single phase 230/240V, size 300 mm sweep, 1400 RPM with louver complete including with all arrangement of making holes on wall, making good and finishing disturbed surfaces matching with the existing surfaces, necessary fixing arrangement such as fastener bolts, nuts, washers etc of appropriate size all as specified and as directed

S&F, storage type water heater (Geyser), BEE 5 Star ratings, 230 Volt AC, 25 Ltrs capacity comprising copper inner tank, viterous enamelled innertank conforming to IS-13273 suitable heatng element, thermostate with adjustable temperature stting 0-90 C, indication lamps provision for inlet outlet and air vent connections & NRV, PVC connection 15 mm size, heavy duty with brass nuts, 450 mm long mounteted on wall surfaces including all fixing arrangement such as faster bolts, nuts washers etc having two year warranty complete including making good disturbed wall surfaces matching with the existing surfaces and finishing all as specified and as directed.

Supplying and laying precast concrete cable cover class LV type -I flat size 250x150x40 mm laid parpendicular conforming to ISI standard to the axis of cable in trenches etc complete all as specified and directed.

S&F, in repair, GI pipe, medium grade, 50 mm bore including all fittings such as bend, tee, elbow, union, reducer etc. laid in floor complete all as specified and as directed .

Supply, Laying and testing, Cable XLPE Insulated, sceened, PVC bedded Galvinised Steel strip or wire armoured, electric power cables (heavy duty )1100 Volts grade with standared aluminium conductor of size 16 Sq mm 4 core connected to existing MCB box / Main switches complete all as specified as directed. NOTE:- Excavation and earthwork shall be measured & paid seperately under appropriate item.

Supply, Laying and testing, Cable XLPE Insulated, sceened, PVC bedded Galvinised Steel strip or wire armoured, electric power cables (heavy duty )1100 Volts grade with standared aluminium conductor of size 25 Sq mm 4 core connected to existing MCB box / Main switches complete all as specified as dircted. NOTE:- Excavation and earthwork shall be measured & paid seperately under appropriate item.

M&L for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick weithing not less than 17.5 Kg buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel, procteded by GI pipe 15 mm bore (light grade) and watering pipe 20 mm bore GI pipe (light grade) and chamber of PCC 1:4:8 type D2 using 40 mm graded stone aggregate and coping shall be in PCC 1:3:6 type C1 using 20mm graded stone agg. 50 mm thick cover of RCC 1:2:4 type B1 using 20 mm graded stone aggregate reinforced with 8 mm dia MS tor bar @ 80 mm c/c both ways including excvation and earth work in any type of soil and removal of surplus soil complete all as shown in electrical plate no 3 of SSR PT 1, 2009 with charcoal dust and salt complete and earth lead connected to earthing test point (up to main switches, DBs) complete all as specified & testing on completion. NOTE:- (i) Item includes the cost of 7.5 mtr length GI pipe for protection for GI earth wire. (ii) Item rates includes the cost of 7.5 mtr earth lead GI earth wire. (iii) PCC pit shall be provided at least 500mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe,bends,elbow etc shall be deemed included in the unit rate.

Supplying, installation, connecting, testing and commissioning of outdoor type distribution transformer of 200 KVA, 11/0.433 KV, 3 phase, 50 Hz, ONAN cooled oil immersed copper wound step down, floor mounted complete with first filling ISI marked filtered & dehydrated transformer oil and other standard fittings / accessories and 7 position off circuit tap changer (tapping range +/- 7.5% in steps of 2.5% each) with vector group DYN -11 complete all as specified and as directed by the Engineer in Charge. Note - (i) The ambient temprature shall be 48 degree Centigrade when measured by the resistance method after continuous full load run . (ii) The transformer shall be complete with standard fittings all as specified and conforming to IS:335 of 1993 for oil and IS: 1180 Part -I of 2014 for transformer and comprising of followings:- (i) One No cable box on LV side (secondary side) consisting of 04 Nos of porcelain bushing with bushing rods and another cable box on HV side (primary side) consisting of 03 Nos of porcelain bushing with bushing rods etc complete with nut, washers, cable gland etc. (ii) Oil conservator tank with filter type drain valve and oil level gauge. (iii) Oil level indicator with minimum and maximum marking (iv) Dehydration silica gel breather assembly with first fill of dehydrating agent and oil seal. (v) Explosion vent with diaphragm complete.

ITEM NO. 179 Contd........................................................................................................................................ (vi) Thermometer pocket on tank cover. (vii) Dial type thermometer vapour pressure having range 0-120 degree C with max reading pointer max temp indicator and resetting device. (viii) Rating plate with terminal marking. (ix) 02 Nos earthing terminal on tank and cover for fixing earth strip of size 32 x 6 mm. (x) Oil level gauge and oil drain filter valve. (xi) Lifting hook. (xii) Oil filler hole with cap /plug with connection complete. (xiii) Air relief valve plug. (xiv) Detachable rollers - 04 Nos (xv) Extra bushing for Neutral out side the cable box for independent earthing for neutral earth. (xvi) First fill of fresh transformer oil confirming to relevant IS and tested up to 40 KV die electric strength.

M&L for switch air break gang operated triple pole mechanically operated mounted on HT insulators (12 insulator type) with DO fuse unit insulator barrel type fuse of suitable rating and MS galvanised steel frame with operating mechanism worked from ground level incl operating rod and operating handle with 11 KV insulation for current rating up to 200 Amp 11000 volts complete all as specified and directed.

M&L SMX type surge arrester (lightning arrestors) confirming to IS-3070 (Part-1) having voltage rating 12 KV, rated frequency 50 Hz, nominal discharge current 65 KA (heavy duty) expulsion type transmission class complete with all fittings suitable for 11 KV, 3 phase earthed distribution system complete all as specified and directed

Supply, erecting and fixing in true vertical position, steel tubular swaged pole (410 SP-55), 11 mtr long, complete with cast iron base plate, pole cap / finial taper plug, bolts, nuts and washers, welded reduced section and longitudinal weld throughout entire length of pole including 2 coats of black bituminous paint externally upto planting depth and remaining exterior portion of pole shall be provided with one coat of red oxide primer and two coats of aluminium paint complete all as specified and directed. (Numbering of the poles shall be done with synthetic enameled painted letter of shape & size as directed.) Note :- Excavation including earth work and PCC foundation will be measured and paid separately

Supply, erecting and fixing in true vertical position, steel tubular swaged pole (410 SP-31) 9.0 mtr long, complete with cast iron base plate, pole cap / finial taper plug, bolts, nuts and washers, welded reduced section and longitudinal weld throughout entire length of pole including 2 coats of black bituminous paint externally upto planting depth and remaining exterior portion of pole shall be provided with one coat of red oxide primer and two coats of aluminium paint incl taking down complete all as specified and directed. (Numbering of the poles shall be done with synthetic enameled painted letter of shape & size as directed.) Note :- Excavation incl earth work and PCC foundation will be measured and paid separately.

M&L for steel tubing galvanised, light grade complete with fittings laid in trenches/ fixed along with poles etc as protection to cables of size 100 mm dia bore complete all as specified and as directed.

S&F aluminium conductor, steel reinforced (ACSR) of any size/description on HT/LT poles/lines incl stringing, tightening, binding to insulators with aluminium wire making and connecting jumpers, connections etc incl connecting, commissioning and testing and providing spacers as required at site complete all as specified & directed.

Supplying, laying, jointing & commissioning of cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminum conductor, 11000 volts grade, (Earthed) cross sectional area 95 sqmm 3 core as per IS 7098 Pt-II complete all as specified and directed.

Supply and fix cable jointing kit for 11 KV (Earthed) grade cable for outdoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured Aluminium conductor cable of size 95 sqmm complete all as specified and as directed.

M & L for Stay assembly complete with accessories as shown in electrical plate No. 1 of 20 mm dia of stay rod, 180 cm long etc complete all as specified and directed. (for HT poles)

Supply and fix loop type insulator vitreous procelain, white , brown or green, large size with overall dimensions 140mm, clearence of hole 25.5mm dia ball and socket type brown, white or green single disc assembly for tension with tension clamps for conductors, working pressure 11000 volts grade etc complete all as specified and directed.

M & L for Stay assembly complete with accessories as shown in electrical plate No. 1 of 16 mm dia of stay rod, 180 cm long etc complete all as specified and directed. (for LT poles).

Supply and fix loop type insulator vitreous procelain, white , brown or green, large size with overall dimensions 65 x 90 mm, clearence of hole 16 mm dia ball and socket type brown, white or green single disc assembly for tension with tension clamps for conductors, working pressure 11000 volts grade etc complete all as specified and directed.

Supply and fix galvanised stay strand, 7/4 mm complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode of size 600X600X6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.50 mtr below the ground level connected to galvanised iron strip of 32x6 mm as earth lead by means of bolts nuts check nuts & washers of galvanised iron or steel, surrounded by charcoal of coke and salt, protected by GI pipe 40 mm bore (light grade), water pipe 20mm bore GI medium grade with funnel and wire mesh,and making chamber of PCC (1:4:8) type D-2 using 40 mm graded stone aggregate and coping shall be in PCC(1:3:6) type C-1 using 20 mm graded stone aggregate, 50 mm thick cover of RCC (1:2:4) type B-1 using 20 mm graded stone aggregate, reinforced with 8 mm dia TMT bars @ 80 mm c/c boath ways including excavation and earth work and removal of surplus soil to distance n exc 50 m complete all shown in electrical plate No 3 of SSR part- 2010 and also including making test point for testing of earthing made out of gun metal or phosphorous bronge size 75x75x25 mm complete all as specified and directed. (i) The cost of GI earth lead & G I pipe of 7.50 mtr length for protection of GI wire and excavation and earth work in any type of soil for pit shall deemed to be included in this item. Note:- Earthing test will be carried out and if desired result not achieved, the earthing will be redone to achieve desired result without any extra payment.

Supplying, fixing, commissioning and testing CPRI approved factory made LT feeder pillar, outdoor type floor mounted, suitable for 415 volts 3 phase 4 wire, 50 Hz AC supply system, having bus bar chamber duly insulated The panel shall be dust and vermin proof, IP 65 class protection and made of 3.15 mm CRCA MS sheet and 50x50x5mm thick angle iron base frame work, powder coated finish over one coat of red oxide primer outside and two coats of red oxide primer on inside, both side opening type, with aprons for cable entry, with double door shutter and locking arrangement of size 120 cm x 80 cm x 40 cm and consisting of the following all as specified. (a) Copper bus bar four strips 600 Amps ,415 volts,fixed on epoxy insulated with panel fixed horizontally, duly insulated with heat shrinkable sleeves in colour code - 01 Set. Incoming (b) MCCB, 04 Pole, 500 Amps with ultimate breaking capacity Icu- 36 KA at 415 volts , adjustable type with thermal and magnetic settings conforming to IEC 60947 Part-I/IS-13947 Part-I - 01 No Outgoing (c) MCCB, 04 Pole, 160 Amps with ultimate breaking capacity 25 KA at 415 volts with fixed thermalsettings conforming to IEC 60947 Part-I/IS-13947 Part-I - 04 No, (Ics=Icu=100%) (d) MCCB, 04 Pole, 100 Amps with ultimate breaking capacity 16 KA at 415 volts with fixed thermalsettings conforming to IEC 60947 Part-I/IS-13947 Part-I - 01 No, (Ics=Icu=100%)

S&F danger notice plate of 1.6 mm thick mild steel sheet vitreous enamaled white, with letters, figures and conventional skull and bones in signal red colour fixed with and including MS clamps, bolts and nuts of approved size for HT, 25x20 cm size complete all as specified and directed.

S&F danger notice plate of 1.6 mm thick mild steel sheet vitreous enamaled white, with letters, figures and conventional skull and bones in signal red colour fixed with and including MS clamps, bolts and nuts of approved size for LT, 20x15 cm size complete all as specified and directed.

M&L for anti-climbing device, spikes type fabricated out of MS bars (round, square and flat) including nuts, bolts, washers and welded in two halves made to shape to suit the cross section of the HT poles complete all as specified and directed.

M&L for mild steel cross arms, bracings supports, clamps and back plates fabricated from structural steel sections, channel including nuts, bolts, washers welding, bending cold or not, drilling holes for bolts in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint complete all as specified and as directed.

M&L for PCC cable cover class HV type 1 flat size 300 mm x 180 mm x 40 mm, ISI marked across the cable for protection of cable after sand cushioning complete all as specified & directed.

M & L for preparation of new plastered surface and applying two coat of cement base paint over a coat of white cement as primer on external surface etc complete all as specified and as directed.

Disc type insulator porcelain vitreous 145mm height and 225 mm dia ball and socket type brown white or green single disc assembly for tension with tension clamps for condutors working pressure 11000 volts complete all as specified and directed.

PIn type vitreous porcelain white brown or green insulator including one galvanised mild steel spindle two galvanised iron wasther and one galvanised iron nut, 150mm height 150mm dia for 11000 volts grade complete all as specified and directed.

Shackle type insulator porcelain vitreous 100mm height and 115 mm dia ball and socket type brown white or green single disc assembly for tension with tension clamps for condutors working pressure 1100 volts all as specified and directed.

PIn type vitreous porcelain white brown or green insulator including one galvanised mild steel sindle two galvanised iron wasther and one galvanised iron nut, 100mm height 65mm dia for 1100 volts grade all as specified and directed.

S & F incl stringing GI continuous GI earth wire of size 4 mm / 3.15 mm dia on HT/LT poles as in cradle guards / earth wires, binding including taking down complete all as specified & directed.

Supply and fixing of GI strip 32 x 6 mm fixed in ducts / on wall / in trenches / floors etc for earthing complete fixed to equipment / test point / earth electrode complete all as specified and directed

M&L MS angles as fencing port, struct cutting tops in shape incl all necessary drilling, notching and reveting etc and similar work confirming fe 310-0 or fe 4120-0 all as specified and directed.

M&L for structural MS frame work half round or other stock section including securing posts and stuts in fencing, frame work for gates of substations, base frame for equipments including securing bolts, posts and sturts in fencing including cutting and makeing shapes as desired, drilling holes, notching for wire cut to size and made to the exisitng shape suitable for fixing MS chequred duct covers / door panels, including nuts, bolts and washers, welding / bracing works, bending cold or hot drilling holes for bolts in any shapeetc flat iron fillets (for securing wire mesh etc) all necessary drilling, bolting or riveting etc and similar work confirming to Fe-290 Gde E-165 including one coat of primer and two coats of synthetic enamel paint to the entire steel surfaces all as specified and directed.

M&L for chain link MS galvanised fencing, dia of chain link n less than 3.5 mm, any mesh any size any type to any type strands complete all as specified and directed.

S&F mild steel screw bolt (mechine made) with hexagonal or square, head, n.exc 5 cm but n.exc 10 cm dia. complete all as specified and directed.

M&L for prepration of steel Surface of one coat of red oxide and two coat of synthetic enamel paint any description, n exc 10cm in width or girth when unconnected with other painting or when painted in a different complete all as specified and directed.

S&F galvanised 2 strand steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire staples or steel pins etc complete all as specified and directed. Note - Each line of horizontal/vertical/diagonal wire to be measured for purpose of payment.

M&L for laying 25 mm graded stone aggregate & stone dust in substations in such a way that after removing of unwanted grass from substations/transformer yard and then levelling at zero level and laying of stone dust of 50 mm thick at an initial layer and then laying of 25 mm gaded stone aggregate 100 mm thick over the stone dust. The quoted rate also includes cleaning and levelling and filling of sub station before laying aggregate. The complete work shall be as decided and directed by engr in charge.

Supply, laying & testing LT cable XLPE, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminum conductor, 1100V grade with stranded aluminium conductor of size 185 sqmm 3.5 core as per IS 7092 Pt-I complete all as specified and directed.

Supply, laying & testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminum conductor, 1100V grade with stranded aluminium conductor of size 70 sqmm 3.5 core as per IS 7092 Pt-I complete all as specified and directed.

Supply, laying & testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminum conductor, 1100V grade with stranded aluminium conductor of size 50 sqmm 3.5 core as per IS 7092 Pt-I complete all as specified and directed.

Supply, laying & testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminum conductor, 1100V grade with stranded aluminium conductor of size 25 sqmm 4 core as per IS 7092 Pt-I complete all as specified and directed.

Supply, laying & testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminum conductor, 1100V grade with stranded aluminium conductor of size 10 sqmm 4 core as per IS 7092 Pt-I complete all as specified and directed.

Deduct schedule of credit (calculation will be done off line) Rs.4,80,583.00

M/s Suresh Chand Gupta

Deepesh Electricals

SAKSHAM BUILDERS AND ENGINEERS

GUPTA ENGINEERING WORKS