Construction of womens space SHE toilet at vadavalli bus stand in ward no 36 West Zone

Amount

Earth work excavation in all kinds of soil including sand, silt, wet sand under water, black cotton, stiff black cotton, clay, hard stiff clay, hard red earth, murram, stoney earth, gravel and shales etc. excepting all kinds of rock and boulders exceeding 0.014 c.u.m. in volume including rough dressing and dumping the excavated materials away from work site manually within 50m initial lead and 2m initial lift as per the direction of Engineer-in-charge.

Cement concrete 1:4:8 (one cement, four M sand and Eight aggregate) using 40mm gauge hand broken granite stone jelly for foundation including dewatering if found necessary and laid in layers of not more than 15 cm thick and compacted, etc., complete complying with standard specification.

Supply and filling with well gravel layer by layer including watering, Ramping etc complete

Supply and fabrication of R.T.S. rods in various dia including cutting bending placing in position and tying etc.

Supply and erecting shuttering including necessary supports for plane surfaces such as RCC column, footing, plinth beam, stair case etc., in all floors using mild steel sheets of 90cm X 60cm and 10 gauge stiffened with welded mild steel angle for boarding supported by casurina props at suitable intervals etc., completed complying with standard specification and as directed. Sl.No.122

Supplying and erecting centering for sides soffits including supports and strutting upto 3.29m high for plain surface such as rectangular column top and bottom slabs of boxing, sill, slabs, sun shade etc., in all floors using mild steel slabs of sizes 90cm x 60cm and BG 10 stiffened with welded mild steel angles of size 25X25x3mm for boarding laid over country wood joists of size 10cm X 6.5cm spaced at about 90cm C/C and supported by casurina props of 10cm to 13cm dia spaced at 75cm C/C etc., complete as directed. Sl.No.123 C Part-II

Cement concrete 1:1.5:3 (one cement, one and a half M sand and three aggregate) using 20mm gauge hard broken granite stone jelly for All RCC items of work excluding centering, shuttering, and cost of reinforcement grill but including curing finishing etc., complete and also including fixing fan clamps and fixtures in RCC works wherever necessary as directed by departmental officer etc., complete.

Fly ash Brick work in CM 1:5 (one cement & five M sand) using size 9"X4 3/8"X 2 3/4" including finishing, curing, etc., complete complying with standard specification - 100CFT

Supply and fixing of Wooden door using with necessary locking arrangements including cost and conveyance etc.,

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Weathering course in concrete broken stone brick jelly 20mm size in pure slacked lime over RCC slab. The proporation being 32:12:5 for requuired slope and the thickness of roof as required and well beaten with wooden beaters etc., completed

Terrace flooring with one couse of pressed tiles of size 23 X 23 in cement mortar 1:3 mix with impermo oil 2% by weight of cement and pointed with same oiled mortar etc complete

Plastering the exposed surface of RCC works in cement mortar 1:3 mix (one cement and three P sand)10mm thick

Plastering with cement mortar 1:5 mix (one cement and five P sand) 12mm thick

Paving the floor with Granite Slab (super fine polished with machine cut edges) of sizes 1.2m x 0.60m and above of 18mm to 20mm thickness in all floors over a base layer of cement mortar 1:3 (one cement and three sand) 25mm thick and white cement slurly layer of 3mm thick over this, laid in situ and pointed with white cement neatly and fixed in position so as to make perfectly smooth and shining to the alignment including cutting the marble slab to size with machine cutting polishing using different grade of corporandum stone, oxalic acid, tin oxide etc., and including hire charges or polishing machinery etc., complete. For Jet Block Colour.

Paving the floor with Vitrified Floor Tiles of size 60 X 60cm of approved brand and colour Marbonite tiles in all floors base layer of cement mortar 1:3 (one cement and three sand) 20mm thick using first quality Marbonite tiles of size 60 X 60cm and point with colour cement neatly and fixed in position so as to make perfectly smooth and to alignment etc., complete complying with standard specification

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from unplasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high nsulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug.

Painting the wall with Texture Finish Paint charges including through cleaning, scrapping, removal of dust and including necessary plaster of paris putty works wherever required etc., completed.

Painting new iron work for doors, windows, grills, weld mesh sceens etc., two coats etc complete

Wiring with 2x1.5 sq.mm. (22/0.3) PVC insulated unsheathed SC copper conductor of 1100V grade insuitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch box with 5A FT switch inflush with wall covered with hylumsheet of 3mm thick with painting of suitable colour for open PVC light/fan point (for electronic regulator) (5 points per coil) SD-19

Wiring with 2x1.5 sq.mm (22/0.3) PVC insulated SC unsheathed copper conductor of 1100V grade insuitable PVC rigid pipe on wall and ceiling with PVC accessories with 150x100x113mm TW switch box for 5A 3pin non interlocking Wall socket with 5A flush type switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC plug point SD-34

Supply and run of 2 of 4sqmm PVC insulated SC unsheathed Cu.conductor of 110V grade in suitable PVC rigid pipe concealed in wall and ceiling with contious Earth wire and making good of the concealed portion with siutable colour etc complete SD-46

Supply and fixing of ceiling fixture 250/300mm complete with gallery etc clear glass Opac/Crystal suitable for 40W / 60W bulb with bulb SD-86

Supply and fixing of 4'40W twin street light fluorescent fitting complete with copper choke and condensor with 32mm dia GIpipe (Class'B') with 1No.32mm GI bend complete on the existing post wall with 16A aerial fuseunit on MS plate with PVC unsheathed copper leads MS clarnps and aluminium painting with fluorescent tubes SD-94

Supplying and fixing in position best white glazed earthernware Oriya type Indian water closet of approved quality of size 550 mm x 440 mm with 'P' or 'S' trap and embedding the closet with trap to shape in position with 40mm brick jelly lime concrete 1:2:5 etc., complete

European Water Closet (Colour) with 'P' or 'S' Trap with Double Flapped seat and seat cover with Brass Highes and 10 litre capacity PVC low level flusing tank with all internal fittings

Supplying and fixing of position of Indian make colour glazed earthwere wash basin 550mm x 400mm with all accessories such as cost Iron brackets, 32mm dia C.P. Waste coupling, Rubber plug and chain, 32mm dia 'B' class, G.I. Waste pipe, 15mm dia, G.M.Wheel valve, 15mm dia Nylon connection, 15mm dia Brass Nipples, 15mm C.P. pillar tap etc

Supplying and fixing of 1000 lits HDPE Water Tanks with suitable specials including cost of materials to site and all other labour charges.etc

Supply and delivery of Electric Mono set centrifugal pump conforming to IS 9079:2002 as amended from time to time, with CIFG 200 Casing, hydraulically and dynamically balanced Bronzegrade LTB-impeller, impeller ring and casing ring ,stainless steel shaft capable of discharging required quantity of water against atotal head noted below due to all causes. Pump shall of BEE 3 Star Rated and capable of discharging the specified quantity at the head noted at the minimum NPSHA at site conditions. The shutoff head shall beat least 25% over and above the head at duty point. The pump shall be suitable for operation in AC three phase, 415V+/-10%,50Hz+/- 5%. Squirrel cage induction motor for continuous operation. The speed of the Pump and Motor shall be not lessthan 2700 to 2900 RPM respectively. (100x20)

Supply of Water supply pipes and specials with approved brand

110 mm dia PVC pipe 10KCS

63 mm dia PVC pipe 6 KCS

20 mm dia PVC pipe

25 mm dia PVC pipe

20 mm dia PVC Coupling

25 mm dia PVC Coupling

20 mm dia PVC Elbow

25 mm dia PVC Elbow

20 mm dia PVC Bend

25 mm dia PVC Bend

110 mm dia PVC Elbow

20 mm dia PVC Tee

25 mm dia PVC Tee

110 mm dia PVC Tee

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Supply and fixing of MS hollow pipe in various dimentions including cost of labour and conveyance of all material to work site etc., complete

Supply and fiixing of Polycarbonate sheet for roofing including cost of labour and conveyance of all material to work site etc., complete

Supply and fixing of Alcopanalling works using Aluminium hollw sections with all sizes and shapes Including all labour charges as per the direction of Dept. off., Etc complete