Loading
Loading…
Loading…
Tender Value
₹13.6 L
EMD Value
₹27,100
Closing Date
17 Sept 2026, 10:30 am6d left
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
45 days
Expenditure
Revenue
HQ
6 conditions · 2 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
As per Part I Offer Letter, Part II General Instructions to tenderer and Tender Conditions & Annexures-Attached
One time maintenance of DSL across Axle shop and Provision of parking stations for each bay in Axle Shop.
RWF-EL-OT-ASC-2026-27-52~RWF
RWF-EL-OT-ASC-2026-27-52
Open
Works - General
18 Months
Bengaluru Urban, Karnataka
₹0
₹27,100
26 Aug 2026
26 Aug 2026
3 Sept 2026
14 items across 6 schedules
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 1,71,100 | ||
| — | 1.00 | Lumpsum 171100.00 | — | ||
| 1.Cutting of DSL AngleThe existing 75x75x8 mm DSL angle shall be cut at:•North end•Near Column 29 - for isolating OAFL and NAFL HT bays. •South end of the bayCutting is to be done to create provision for the parking bay.Proper marking and measurement shall be ensured before cutting.2.Welding of Unwanted Gaps in DSLAll unwanted gaps created in the DSL after cutting shall be:Properly weldedGround smoothChecked for structural continuity3.Mounting of 250/300A Isolators250/300A isolators shall be securely fixed on the respective column.Mounting height and accessibility shall comply with safety standards.Ensure proper alignment and mechanical stability.4.Fabrication of Mounting FrameA suitable mounting frame shall be fabricated using:25x25x3 mm angleFrame shall be:•Properly aligned•Welded securely•Painted with anti-rust coating (if required)5.Additional Supporting Angles & InsulatorsProvide additional support wherever DSL is slightly bent or sagging using:50 x 50 x 6 mm L-angle•Install additional insulators as required.•Ensure proper alignment and prevention of sagging.6.Cable Crimping & Phase ConnectionProperly crimp cables using suitable lugs.Connect cables to all three phases (R-Y-B) of DSL on both sides of the cut section.Ensure correct torque tightening and insulation integrity.7.Cable Cleats InstallationProvide cable cleats for:Incomer cables to DSLOutgoing cables from DSL to isolatorEnsure proper spacing, clamping, and neat cable routing.8.Final Dressing & WeldingEnsure neat cable dressing and alignment.Finish all weld joints properly.Remove sharp edges and clean the work area after completion.9.Replacement of Broken InsulatorsIdentify and remove damaged/broken insulators.Replace with new insulators of suitable rating & Ensure proper fixing, insulation clearance, and mechanical strength.10.Align the current collector assembly and the structure. Align the current collector assembly with the DSL and supporting structure.Ensure smooth movement and proper contact pressure.& Check for:Correct tracking, misalignment or binding &Proper electrical contact across full travel length | — | — | — | 1,71,100 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
PartIOfferletter.pdf
ATTACHMENT
PartIIInstructionstoTenderers.pdf Part II Instructions to tenderer
ATTACHMENT
PartIIISpecialconditions.pdf
ATTACHMENT
PartIVPricesandpayments.pdf
ATTACHMENT
PartVSchedule.pdf
ATTACHMENT
PartVIAnnexures.pdf
ATTACHMENT
PartVIINITfore-tender.pdf
ATTACHMENT
Part VIII GCC
ATTACHMENT
PartIIInstructionstoTenderers.pdf
ATTACHMENT
GCC_April-2022_merged_compressed.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .