SPECIAL REPAIR BLDG NO P-662 AT JAISALMER AND PROVN OF BIO TOILET TOWARDS CONSERVATION OF WATER AND ENHANCING HYGINENE STANDARDS AT CHANDHAN AND AT AF STN JAISALMER

Amount

Machine cut Kota stone slab 18- 20mm thick, as in floor, riser of step, etc. laid over and including rendering of 15mm thick in cement mortar 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including demolition of existing stone slab complete all as specified and directed.

Machine cut Kota stone slab 18- 20mm thick, as skirting, dado and pillar etc. laid over and including rendering of 10mm thick in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including demolition of existing stone slab complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n. exc 1.5 Sqm each complete all as specified and directed.

Factory made steel windows with side hung shutters including projecting type hinges with steel handle of MS flat 25x5mm and 2 Nos steel tower bolts, 100mm long fixed to shutter complete with and including glazing bars, dovetailed or welded and also including painting the exposed steel surfaces with one shop coat of red oxide Zinc-Chromate primer including taking out old existing steel window frame complete all as specified and as directed.

All as per SI No 4.00 here-in-before but without glazing bars complete all as specified and as directed .

Taking down shutters any description area exceeding 1.00 sqm each but not exceeding 2.00 sqm each complete all as specified and directed.

Powder coated aluminium (minimum thickness of powder coating 50 micron) frame /shutter work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including roller for sliding window, handle, locking device, necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and as directed .

Expanded metal mesh Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and as directed .

5 mm thick Figured glass and fixed to aluminium Ventilation in square exc 0.5 sqm in each pane complete all as specified and directed.

Stainless steel (Grade S 304) wire cloth 0.36mm nominal dia of wire and average width of aperture1.4mm and fixed with stainless steel wire staple fixed with aluminium beading etc complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 Sqm but not exc 4 sqm each complete all as specified and directed.

Mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete of Gde E-165 (Fe-290), drilled for fixing of steel sheeting or other covering, doors, etc to be prepared for hanging or sliding with and including either hooken and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing in position complete all as specified and directed. Note : Cost of welding butt hinges to the door frame deemed to included in quoted rate .

30 mm thick Flush shutters factory made solid core construction, with block board core, and ply wood face panels, commercial type on both side (ISI marked) fixed to chowkhat complete all as specified and directed.

Factory made Second class hard wood 35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. divided into squares with plain chamfered or rounded, mitred and rebated sash bars any numbers, edges of framing plain, chamfered or founded, fitted with cut and mitred beads for securing glass or wire cloth any number, etc sizes of members of shutter as specified in SSR Part-I complete all as specified and directed.

PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as bed block, bend fixing hold fast ,filling of door frame etc including necessary use and waste of formwork complete all as specified and as directed

PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube 19mmx19mmx19 gauge and PDM rubber gasket weather seal to be provided through out the frame. The profile shall be mitre cut at two corners and jointed by inserting 02 Nos of 150mm long brackets of 15mmx15mmx15 gauge MS square tube inside the 19mmx15mm MS square tube and suitable screwed including taking down existing complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick (style), consisting of frame made out of MS tubes for stiles and for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed.

100mm Butt hinges extruded stainless steel hinge pin type anodised complete all as specified and directed.

100mm Butt hinges extruded stainless steel hinge pin type anodised fixed as in repair complete all as specified and directed.

200mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

200mm long aluminium anodised barrel tower bolts of extruded section fixed as in repair complete all as specified and directed.

Aluminium handle 150mm long , fabricated type anodized complete all as specified and directed.

Aluminium handle 150mm long , fabricated type anodized fixed as in repair complete all as specified and directed.

300mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

300mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy fixed as in repair complete all as specified and directed.

Mild steel helical door spring 300 mm long including roller and roller plate complete all as specified and as directed .

Mild steel helical door spring 300 mm long including roller and roller plate fixed as in repair complete all as specified and as directed .

Stainless steel curtain rod fancy type 25mm dia with side bracket fixed with stainless steel matching pair of brackets fixed at both ends with screws on walls/beam fixed as in repair complete all as specified and directed.

Non skid glazed ceramic tile coloured tiles (1st quality/ premium quality) joint free tile 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exc. 0.38 sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed or bedding layer of cment mortar (1:6) including dismantling floor, hearth or wall tiling with cement mortar bedding complete all as specified and directed.

Non skid glazed ceramic tile coloured tiles (1st quality/ premium quality) 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exc. 0.18 sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed or bedding layer of cment mortar (1:6) including dismantling floor, hearth or wall tiling with cement mortar bedding complete all as specified and directed.

Glazed coloured ceramic tiles in dado/skirting 300x450x6-7mm thick as in dado and skirting over and including 15mm thick cement and sand mortar (1:4) backing coat set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tile and including dismantling of existing tiling with cement mortar bedding complete all as specified and directed.

18mm to 20mm thick granite stone work (table rubbed and polished) as in steps, jambs, pillars, window-cills, cooking platforms and like in cement and sand mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15 mm cement screed bed in cement and sand mortar 1:6 laid and jointed in grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to accommodate counter basin etc including dismantling of existing stone slab bedding complete all as specified and as directed.

Rounding to edges of stone slabs one edge such as in steps, cooking platform and other similar situations complete all as specified and as directed.

Reinforced cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) as in slabs supported on walls, roofs, landings, balconies, canopies, chajjas and the like including demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for and removing the debries from site complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

Galvanized steel water tubing medium grade of 15mm bore with & including all fittings fixed to walls and ceiling or laid in floors, including taking up or down old unserviceable steel water tubing , complete all as specified and directed.

Galvanized steel water tubing medium grade of 20mm bore with & including all fittings fixed to walls and ceiling or laid in floors, including taking up or down old unserviceable steel water tubing , complete all as specified and directed.

Cutting chases, pinning in, making good to facings as original where required and pointing in cement and sand mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exceeding 10cm girth in stone concrete blocks or slabs complete all as specified and directed.

20mm dia Gun metal globe or gate valve, with iron wheel head, screwed both ends, ISI marked fixed as in repair complete all as specified and directed.

Rotational moulded polyethylene water storage tanks 1000 Litre capacity triple layer (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position including 20mm dia PVC float valve & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. fixed with ball valve of high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball and screwed for iron pipe 20mm bore including dismantling of existing tank complete all as specified and directed.

15mm thick plaster in cement mortar (1:6) on block masonry/stone masonary surfaces or other than of fair faces of brick or concrete surfaces, finished even and fair complete. including taking down old plaster complete all as specified and directed.

15mm thick plaster in cement mortar (1:4) on wall surfaces finished even & smooth, without using extra cement including taking down old plaster complete all as specified and directed.

5mm thick ceiling plaster in cement mortar (1:3) on uneven faces of concrete surfaces of ceiling soffits of chajjas/ drop & roof projectiom facia etc , including taking down old plaster complete all as specified and directed.

Precast cement concrete (1:3:6), type C-1 (using 20mm graded stone aggregate) as solid block masonary exceeding 10cm and set in cement and sand mortar (1:6) , etc. including demolition of existing concrete complete all as specified and directed.

Raking out joints/ pointing to random rubble or polygonal rubble uncoursed or brought up to courses in walls etc complete all as specified and directed.

Preparing new plaster surfaces and applying a coat of readymixed wall putty on entire surface of wall etc cutting and finishing with appropriate sand paper and applying two coat of oil bound distemper (White or tinted) over a one coat of primer after smoothening of surfaces of wall complete all as specified and directed.

Complete removal of existing treatment, filling up undulation surfaces and applying a coat of readymixed wall putty on entire surface of ceiling etc cutting and finishing with appropriate sand paper and applying two coat of oil bound distemper (White or tinted) over a one coat of primer after smoothening of surfaces of wall complete all as specified and directed.

Preparing new plaster surfaces and applying a coat of readymixed wall putty on entire surface of ceiling etc cutting and finishing with appropriate sand paper and applying two coat of oil bound distemper (White or tinted) over a one coat of primer after smoothening of surfaces of ceiling complete all as specified and directed.

Complete removal of existing treatment, filling up undulation surfaces of ceiling , cutting and finishing with appropriate sand paper and applying two coat of oil bound distemper (White or tinted) over a one coat of primer after smoothening of surfaces of ceiling complete all as specified and directed.

Preparation of newly plastered wall surfaces and applying two coats of cement based paint (tinted) over a coat of alkali resistant primer as approved complete all as specified and directed.

Preparation of old plastered wall surfaces and applying one coat of cement based paint (tinted) as approved complete all as specified and directed.

Preparation of newly surfaces of wood or wood based material of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified and directed.

Preparation of old painted wooden surfaces of any description exceeding 10cm width or girth and applying one coat of synthetic enamel paint of any tint etc complete all as specified and directed.

Prepariation of newly steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint already coat of primer complete all as specified and directed.

Prepariation of newly steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Preparation of old painted steel surfaces over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Vitreous china squatting pan 'Orissa Pattern' of size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipe) with P' or 'S' trap complete including jointing and making good to floor provision of PCC 1:5:10 bed including dismantling old unserviceable WC complete all as specified and directed.

Counter wash basin Oval shape of size (560x450)mm white colour excluding taps, including dismantling and taking down old unserviceable complete all as specified and directed.

Chromium plated shower rose 75mm dia with or without CP arms swivel joint, including fixing to steel pipe and fixed as in repair complete all as specified and directed.

Vitreous china urinal, full stall type, white coloured, including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs and including 60mm long brass screws, pointing around urinal back in cement, with and including grating and union for discharge pipe, including 40mm size brass chromium plated waste coupling with long screwed shanks and flynuts, flange end bedded in red lead cement and other end including urinal spreader fixed as in repair complete all as specified and directed.

Vitreous china urinal, half stall type, white coloured, including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs and including 60mm long brass screws, pointing around urinal back in cement, with and including grating and union for discharge pipe, including 40mm size brass chromium plated waste coupling with long screwed shanks and flynuts, flange end bedded in red lead cement and other end including zerodor water less urinal kit stainless steel completed all as specified and directed. fixed as repair complete all as specified and directed.

10 Litres capacity PVC valve less syphonic action type, flushing cistern low level, white coloured, with inlet, ball valve, float and handle including brackets complete with flush pipe and fixed as in repair complete all as specified and directed.

15mm bore chromium plated ,fancy type bib taps, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed as in repairs complete all as specified and directed.

15mm bore sawan neck/long neck fancy type pillar tap cast copper alloy chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screw shanks screwed for iron pipe or union fixed as in repair complete all as specified and as directed.

15mm bore brass chromium plated angle cock/stop valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed as in repair complete all as specified and directed.

PVC connection suitable for 15mm bore with PTMT nuts of 600mm length and fixed as in repair complete all as specified and directed.

Sheet glass shelf assembly consisting of 5.5mm thick glass shelf 12cm wide with fixing chromium plated bracket, guard and railing 55/56cm long fixed as in repair complete all as specified and directed.

Tubular towel rail, stainless steel, 20mm dia, D type, 60cm long fixed with & incl chromium plated brass screws and wooden / plastic cleat fixed as in repair complete all as specified and directed.

Cutting hole into or through brick/stone walls built in cement mortar for inserting hold fast superficial area exc 150 sq cm and n.exc 400 sq cm and making good dismantled portion in CM 1:3 or cement concrete 1:2:4 type B1 as required exc half brick but not exc one brick complete all as specified and as directed

PVC (SWR) floor trap 75mm dia outlet plain with grating including jointing with solvent cement for trap fixed as in repair complete all as specified and directed.

110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches/floor fixed as in repair complete all as specified and directed.

110mm bore PVC (SWR) bend any radius with access door provided fixed as in repair complete all as specified and directed.

110mm bore PVC (SWR) Junction Single (Single T) equal or unequal provided with access door fixed as in repair complete all as specified and directed.

110mm bore PVC (SWR) vent cowl fixed complete all as specified and directed.

75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches/floor fixed as in repair complete all as specified and directed.

75mm bore PVC (SWR) Junction Single (Single T) equal or unequal provided with access door fixed as in repair complete all as specified and directed.

75mm bore PVC (SWR) bend any radius provided fixed as in repair complete all as specified and directed.

75mm bore PVC (SWR) bend any radius radius with access door provided fixed as in repair complete all as specified and directed.

Stack clamp made out of MS flat 50 mm x 5mm and 16 mm dia round iron stays, including bolts & nuts, securing ends of stays to walls or roof for 110mm bore pipe including two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces fixed as in repair complete all as specified & as directed.

Stack clamp made out of MS flat 50 mm x 5mm and 16 mm dia round iron stays, including bolts & nuts, securing ends of stays to walls or roof for 75mm bore pipe including two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces fixed as in repair complete all as specified & as directed.

Salt glazed stone ware gully trap size 150x150mm, square,type 'P' including setting and jointing to drains with cement mortar 1:1 and CI grating including demolition of existing traps complete all as specified and directed .

Dismantling wrought iron or mild steel work of any description not otherwise provided for balcony railing,etc complete all as specified & as directed.

Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work confirming to Fe-410W Grade E-165 complete all as specified and directed.

75mm thick Plain Cement Concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in plinth protection and flooring and provided joints 10mm wide & full depth at 3m distance and every change of direction filled with sand and bituminious mix 1:3 including demolition of existing concrete and removal debris outside MD land complete all as specified and directed.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc. or for laying of cables, pipes, erection of poles, structs/stays etc. or for shafts, wells, cesspits, manholes, pier holes, etc not exceeding 10 sqm on plan and getting out in any type of soil complete all as specified and directed.

150mm bore reinforced concrete pipe, class NP2, laid and jointed with collars, laid and jointed on concrete bed complete including testing, after demolition and breaking up existing drain pipes set in cement mortar including bedding haunching complete all as specified & as directed.

P:C:C 1:3:6 type D-2 using 40 mm graded stone aggregates as in beds of pipe 150 mm bore, laid to required slope including packing under and haunching against the side of pipes after they are laid and tested complete all as specified and as directed Note: - (i) Thickness of concrete bed below the barrel of pipe shall be 10cm. (ii) Pipe shall be measured & paid for separately. (iii) Width of concrete bed shall be equal to outer dia of drain pipes (not of sockets/collars) plus 30cm. (iv) The rate includes for all necessary shuttering and support to concrete and for laying beds to falls.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in soft/loose soil complete all as specified and directed.

Removal of excavated soil/ material to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.50 metre above the starting point complete all as specified and directed.

Stainless steel (Grade S 304) wire cloth 0.36mm nominal dia of wire and average width of aperture1.4mm and fixed with stainless steel wire staple fixed with aluminium beading etc fixed as in repair complete all as specified and as directed.

Stainless steel 40mm dia decorative knob for kitchen cup board fixed as in repair complete all as specified and directed.

150mm length floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in door, fixed as in repair complete all as specified and directed.

Mirror polishing on marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish complete all as specified and as directed.

10mm thick cement screed in cement and sand mortar (1:3) on roof surfaces, including finished even and smooth without using extra cement to receive roof treatment, mixed with water proofing compound @ 3% by weight of cement over cleaned roof surface, as in grading to RCC roof surface complete all as specified and directed. Note : Water proofing compound shall be measured and paid separetely.

Supply only integral water proofing compound complete all as specified and directed

Roof treatment with polymeric membrane (APP based) with non woven polyster mat as reinforcement with following:- (a) M & L for surface preparation by removal of existing treatment of tar felt treatment/PCC/plaster/tiling/loose particle to ensure of clean. Smooth and very surface and preparing surface. (b) M&L for providing & laying a coat of cold applied bitumen 85/25 based primer on entire surface @ 0.300 ltr/Sqm of dry and clean surface. (c) M&L for applying a tack coat of hot blown bitumen 85/25 grade @1.2 Kg/Sqm grouted all as specified and as per manufacturer instruction and spraying fine sand over the bitumen being non accessible roof. (d) M&L for providing & laying APP based polymeric membrane of 3mm thickness of weight of 3.0 Kg/Sqm with non woven polyster fibre as in reinforcement on primed surfaces by torch application with side over paps & tints over laps etc apper manufacturers instruction.

Plan cement concrete (1:2:4) type B-0 (using 12.5mm graded stone aggregate) as in padding ,roof kerb or mud step or similar work etc including weathering, slightly rounded or chamfered angles and throating, necessary formwork as required to maintain proper slope including demolition of existing complete all as specified and directed.

Surface excavation not exc. 30cm averaging 15 cm deep in any type of soil getting out complete all as specified and as directed

Plain cement concrete 1:4:8 type D 2 (using 40 mm graded stone aggregate) as in foundation filling complete all as specified and as directed

Mild steel TMT bars 6 mm dia and over upto and including 8 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Use and waste of form work to side of concrete ffoundations, footing ,bases of column, raft and raft beam ,side of soffit (if any ) of foundation and plinth beam and similar work flat and rough finished surfaces of concrete complete all as specified and as directed .

Jodhpur stone roof slab, self faced 7.50cm to 10cm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted in cement and sand mortar 1:3 including demolition / removal of existing stone slabs any thickness complete all as specified and directed.

Water proofing roof treatment, consists of a five layered atactic polypropylene modified polymeric membrane of minimum 3 mm thick and minimum weight not less than 3.0 Kg/sqm, reinforced with polyster non woven fabric matt (weight not less than 150 gm/sqm), laid with LPG torch forced application over roof surface, with a side & end overlaps of minimum 100 mm, with and including Bituminious primer @ 0.3 ltr per sqm confirming to IS 3384-1986 on roof surfaces piror laying APP and a coat of bituminous aluminium primer @ 100 gm/sqm on top, including sealing all joints by thermo fusion, complete all as per manufacturer's instructions.

Use and waste of form work to Chajjas, chullah hoods, water troughs and similar items including edges flat and rough finished surface of concrete complete all as specified and as directed

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.

Formwork to sides for rough finished flat formwork to side of concrete footing, column, base of column, raft and raft beam, plinth beam, sides and soffit (if any) of foundation etc similar work for rough finished surface of concrete complete all as specified and directed.

Reinforced cement concrete M-25 (using 20mm graded stone aggregate) as in foundation, including rafts, footing, foundation beams; plinth beams; bases for columns, basement slabs, under piles and mass concrete complete all as specified and directed.

Reinforced cement concrete M-25 (using 20mm graded stone aggregate) as in slabs supported on walls,beams and columns in floors, roofs landings balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Reinforced cement concrete M-25 (using 20mm graded stone aggregate) as in chajjas complete all as specified and directed.

Reinforced cement concrete M-25 (using 20mm graded stone aggregate) as in beams, cantilevers, lintels over 1.5m span complete all as specified and directed.

Anodised aluminium snap grid frame work for false ceiling as per manufacturer's instructions with hangers from RCC soffit/steel trusses with 6mm dia GI rod (upto 1200mm length) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40x3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long with including exposed metal frame ceiling with 12mm thick mineral fiber decorated board , 600mmx 600mm in size, fixed with screw to aluminium work or with staples on snap grid in ceiling, flat or sloping complete all as specified and directed.

Preparation of newly plastered surfaces or unplastered surfase of walls and applying two coats of oil emulsion distemper over a coat of chalk whitening complete all as specified and directed.

Preparation of newly plastered surfaces or unplastered surfase of ceiling and applying two coats of oil emulsion distemper over a coat of chalk whitening complete all as specified and directed.

Aluminium extruded section body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851-1000mm in width & weight between 61 to 80 Kg, complete all as specified and directed.

15mm bore pillar tap cast copper alloy chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screw shanks screwed for iron pipe or union fixed as in repair complete all as specified and as directed.

White coloured vitreous china urinal (Female) l type with all necessary fittings brass chromium plated waste coupling with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified and directed.

32/40mm bore spring type PVC waste pipe min 1.0 mtr long fixed to WHB & sink etc fixed as in repair complete all as specified and directed.

Shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and directed.

Liquid soap container of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms ) complete all as specified and directed.

Rotational moulded polyethylene water storage tanks 1000 Litre capacity triple layer (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position including 20mm dia PVC float valve & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. fixed with ball valve of high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball and screwed for iron pipe 20mm bore including dismantling of existing tank complete all as specified and directed.

PTMT Grating doom 100mm dia complete all as specified and directed.

PTMT Grating doom 125mm dia complete all as specified and directed.

110mm bore PVC (SWR) bend any radius provided fixed as in repair complete all as specified and directed.

Hardcore of broken stone or boulders of gauge not exceeding 63 mm, deposited, spread and leveled in layers not exceeding 15 cm thick, watered and rolled to a true surface complete all as specified and directed

Cutting into existing manhole for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or ¾ section) in cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate, smooth finished and reforming benching as required for 150 mm bore pipe complete all as specified and as directed

75 mm thick PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base including finishing the top surface of concrete even and rough to receive floor complete all as specified and as directed

60mm thick,interlocking paver block M-35 grade machine pressed factory made rubber moulded precast concrete any shape and size conforming to IS-15658-2006 of with grey cement with pigment including 25mm thick machanicaly compacted thickness of sand bedding below paver tiles laid to required level & slope and dismantling of existing tiling with cement mortar bedding complete all as specified and directed.

Taking down carefully existing unserviceable/perished conduit/ batten/ casing caping aluminium/copper point wiring any type for light, fan, bell, socket, power point etc complete including all fixtures and fittings such as batten/ conduit/casing caping, switches, sockets, ceiling rose, pendent holder, lamp holders, bracket holders, light fittings, top sheet covers, fan regulators etc and making good the disturbed surfaces of wall/ceiling complete all as specified & directed.

Point wiring for one light point/ fan point controlled by one, one way switch with 1.50 sqmm PVC insulated and unsheathed multistranded copper conductor Flame Retardant Low Smoke & Halogen (FRLSH) cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor Flame Retardant Low Smoke & Halogen (FRLSH) cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including non metalic rigid PVC conduit 20 mm dia with accessories fixed to cutting chases in walls by cutter and making good the surface in cement and sand mortar 1:3 and to the original specification and PVC conduit on ceiling for steel structure/surfaces conduit with clamps, gutties etc for RCC ceiling with including cast iron/pressed steel/wooden terminal boxes (as per site requirement) including providing new 3 mm thick plastic laminated sheet cover (Hylem) complete all as specified and directed.

All as per serial item No. 134.00 here-in-before but for one 3 Pin, 5/6 Amps, socket outlet controlled by one 5/6 Amps switch on independent board complete all as specified and directed.

All as per serial item No. 134.00 here-in-before but for one 3 Pin, 5/6 Amps, socket outlet controlled by one 5/6 Amps switch on same board complete all as specified and directed.

Point wiring for one 6 Pin, 15/16 Amps socket outlet controlled by one switch on independent board with 4 Sqmm single core PVC insulated and unsheathed multistranded copper conductor Flame Retardant Low Smoke & Halogen (FRLSH) cable 1100 volt grade including 4 Sqmm single core PVC insulated and unsheathed multistranded copper conductor Flame Retardant Low Smoke & Halogen (FRLSH) cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including PVC casing & caping with accessories fixed on surface of walls/ceiling by means of PVC sleeves/dash fasteners with cadmium plated screws, all as per IS, terminated & including suitable size module boxes for housing of modular switches, sockets, regulators complete all as specified and directed. Note : (i) Unit rates quoted by contractor shall be deemed to included for cutting chases in walls, ceilings and making good surfaces in cement and sand mortar (1:3) and finishing the surfaces to match with existing surfaces. (Make : Hylem/Anchor including machine screws and washer etc for fixing switches sockets etc including 4 sqmm copper conductor, standard (green colour earth), PVC insulated unsheathed earth wire to commen earth and connected to earth dolly as specified and directed.

Switch piano, flush type, Single Pole, one way, 5/6 Amp, 240 Volts (ISI Marked) complete all as specified and directed.

Switch piano, flush type, Single Pole, one way, 15/16 Amp, 240 Volts (ISI Marked) complete all as specified and directed.

Socket outlet, 2 in 1, 3 pin, 5/6 Amp, flush type, 240 Volts (ISI Marked) complete all as specified and directed.

Socket outlet 2 in 1, 3 pin, 15/16 Amps, flush type, 240 Volts (ISI Marked) complete all as specified and directed.

Switch piano, flush type, Single Pole, two way, 5/6 Amp, 240 Volts (ISI Marked) complete all as specified and directed.

Electronic fan regulator,Stepped type , flush type and connecting up, 120 watt, 240 volt (ISI marked) complete all as specified and directed.

Ceiling rose, surface Bakelite 65 x 17.50 mm of three terminals PVC / Polycarbonate,isolated body complete all as specified and as directed.

Sub main wiring with 6.00 sqmm, two single core, PVC insulated unsheathed multistranded copper conductor FRLS 1100 volts grade conforming to IS 694 including and 6.00 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour including drawn through in 25mm dia PVC conduit incl taking existing complete all as specified and directed. Note : Two run of 6.00 sqmm cable and one run of 6.00 sqmm cable as earth wire continuity conductor and one run 25mm dia PVC conduit shall be measured & paid as one unit (running metre).

Sub main wiring with 4.00 sqmm, two single core, PVC insulated unsheathed multistranded copper conductor FRLS 1100 volts grade conforming to IS 694 including and 4.00 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour including drawn through in 25mm dia PVC conduit incl taking existing complete all as specified and directed. Note : Two run of 4.00 sqmm cable and one run of 4.00 sqmm cable as earth wire continuity conductor and one run 25mm dia PVC conduit shall be measured & paid as one unit (running metre).

Sub main wiring with 2.5 sqmm, two single core, PVC insulated unsheathed multistranded copper conductor FRLS 1100 volts grade conforming to IS 694 including and 2.50 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour including drawn through in 25mm dia PVC conduit incl taking existing complete all as specified and directed. Note : Two run of 2.50 sqmm cable and one run of 2.50 sqmm cable as earth wire continuity conductor and one run 25mm dia PVC conduit shall be measured & paid as one unit (running metre).

MCB, Single Pole, 6 to 32 Amps rating, with over load and short circuit protection 'C' curve and rupturing capacity 10 kA, 240 Volt grade, AC supply, 50 Hz and making connections using suitable size copper lugs/thimbles including taking down existing complete, all as specified & directed.

MCB, SPN, 32 Amps rating, with over load and short circuit protection 'C' curve and rupturing capacity 10 kA, 240 Volt grade, AC supply, 50 Hz and making connections using suitable size copper lugs/thimbles, including disconnecting & taking down old unserviceable MCB, complete all as specified & directed.

MCB, TP, 100 Amps rating, with over load and short circuit protection 'C' curve and rupturing capacity 16 kA, 415 Volt grade, AC supply, 50 Hz and making connections using suitable size copper lugs/thimbles, including disconnecting & taking down old unserviceable MCB, complete all as specified & directed.

MCB, TPN, 63 Amps rating, with over load and short circuit protection 'C' curve and rupturing capacity 10 kA, 415 Volt grade, AC supply, 50 Hz and making connections using suitable size copper lugs/thimbles, including disconnecting & taking down old unserviceable MCB, complete all as specified & directed.

LED tube light fittings of cap 10W , Two feet basic all purpose surface and wall mounted LED batten with extruded aluminium housing & integrated electronic driver with all including taking down old unserviceable LED complete all as specified and directed

LED tube light fittings of cap 20W , four feet Basic all purpose surface and wall mounted LED batten with extruded aluminium housing & integrated electronic driver with all including taking down old unserviceable LED complete all as specified and directed .

Sheet metal enclosure powder coated single phase DB SPN 12 ways (2 +10 way) and neutral 240 Volts, AC supply, 50 Hz, with 200 Amps rated copper bus bar Double Door (IP-43 IK 09 with metal door) suitable for fixing of MCBs including fixing of lugs in main incomming and outgoing line and fixing of cable glands of suitable size including grouting flush in the wall by means of nuts, bolts, angle iron and making good disturbed surfaces including taking down old unserviceable DB complete all as specified and directed.

Sheet metal enclosure powder coated single phase DB SPN 4 ways and neutral 240 Volts, AC supply, 50 Hz, with 200 Amps rated copper bus bar Double Door (IP-43 IK 09 with metal door) suitable for fixing of MCBs including fixing of lugs in main incomming and outgoing line and fixing of cable glands of suitable size including grouting flush in the wall by means of nuts, bolts, angle iron and making good disturbed surfaces including taking down old unserviceable DB complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of plate not less than 1.5 deep below normal ground level and connected to and including galvanized earth lead wire 4mm dia upto 7.5 metre by means of GI nuts, bolt, check nuts, washers thimbles, etc as shown in electrical plate No 03 SSR Part I and connection to main switch board or panel and testing on completion including excavation and earth work in any type to soil, returning fitting in and removal of surface spoil to a distance not exc 50 metre, PCC chamber (1:3:6) type C-2, charcoal and salt mixed layer 15cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe light grade 20mm bore for watering and 15mm bore meter long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25mm x 3mm, bolts, nuts and washers 75mm thick RCC cover 1:2:4 type B-1 shall be provided on CI frame etc complete all as specified. Note - (i) PCC chamber shall be constructed at least 1.5m away from the earth electrode. The pipe for watering shall be provided in slanting manner. The cost of 7.50m GI pipe for protection of earth wire/strip .(ii) Quoted amount deemed to include the cost of excavation /earthwork , PCC pit , funnel , cover GI medium grade protectiom pipe.

Exhaust fan, steel body ,AC single phase 230V of size 450mm sweep with blades and frames and louvers including making holes in to the wall as per fan size and making good the disturved surfaces complete all as specified and directed.

Sheet metal enclosure for VPTN DBs 4 way , double door, (IP-43) built in bus bars complete suitable for 415 Volts AC, 50 Hz , supply , suitable for incoming MCCB and outgoing MCBs and fixed in recess in brick masonary wall complete all as specified and directed.

Taking down carefully ceiling fan 230 volts single phase 50 Hz from the position after dismantling fan blades of any sweeps and carrying out complete servicing with and including cleaning, greasing, replacing flexible 3 core cable of size 1.5 Sqmm with copper conductor from ceiling rose to fan, replacing rubber reel, split pins, check nuts, PVC connector complete with and including painting with 2 coats of synthetic enamelled paint over a coat of red oxide anticorrosive primer after rubbing entire fan body and blades and fixing back the fan in position complete all as specified and directed.

Taking down carefullygeysers and deposited to MES store complete and hanging /re-fixing only of geysers after collection from MES store yard including necessary fasteners complete all as specified and directed.

LED Street Light of capacity 30 Watt with inbuilt Driver having pressure die cast aluminium housing , IP 66 having efficiency >100 lumins/watt, operating voltage-120-270 volts, PF >.95, THD < 10 % Suitable for 30 to 40 mm O.D mounting pipe and suitable for mounting on wall/pole with. Necessary Mounting arrangements) including connecting up with three core twisted flexible copper conductor cable with suitable size. mounting pipe/Bracket, Nut Bolts and accessories including disconnected and taking down old US light complete all as specified and directed

Exhaust fan, steel body,AC single phase 230V of size 300mm sweep with blades and frames and louvers including making holes in to the wall as per fan size and making good the disturved surfaces all as directed.

MCB Protected Socket (Modular AC Box, Metal clad box) Two Module, Single Pole, 20 Amps, repturing capacity 10 kA and neutral enclosure in sheet steel with a two pin and earth plug and socket including taking down old unserviceable complete all as specified and directed.

BHAGWATI CONSTRUCTION

M/s Fateh Enterprises