Landscaping and beautification of retrieved land adjoining to Bahu Fort by way of construction of green tunnel along walk ways, open air theater, viewing deck, musical fountain, platform for protection of old trees etc.

Amount

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: All Kinds of Soil

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20mm nominal size) Crushed

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:5:10 (1 cement: 5 coarse sand :10 graded stone aggregate 40mm nominal size) Crushed

Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and fixing of See through Jali in Green tunnel along the track at both sides and top of tunnel with mild steel glavanzied (G.I) with dia of wire 4mm

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand)

12mm Cement plaster of mix: 1: 4 ( 1 cement : 4 fine sand)

Dry random rubble masonry with hard stone in foundation and plinth Without bond stone ( Nallah)

Centering and shuttering including strutting, propping etc. and removal of form for: Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Supplying and stacking of good earth at site including royalty (earth measured in stacks will be reduced by 20% for payment)

Supplying and stacking of well decayed cow dung manure at site including royalty (cow dung manure measured in stacks will be reduced by 8% for payment)

40 mm thick fine dressed and rubbed stone flooring over 20mm (average) thick base of cement mortar 1:5 (1 cement: 5 coarse sand), with joints 3mm thick, side buttered with cement mortar 1:2 (1 cement : 2 stone dust) admixture with pigment to match the shade of stone and pointing with the same mortar and curing complete. Red sand stone

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels (Area of slab upto 0.5 sqm) Granite of any colour or shade 18mm thick

Providing and fixing of Fossil mint Sand Stone of minimun 25mm thick of Jaipur Rajsthan ( Size of stone 1'-0"x 2'-0" )

Extra for Rangoli design on white marble at top platform as per the direction of Engineering Charge

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m in -All kinds of soil.

Extra over item No. 14 for pre finished nosing in treads of steps of sand stone slab. as per the direction of Engineering Charge

Distempering with 1st quality acrylic distemper (ready mixed)having VOC content less than 50 gms/litre, two or more coats on new work of approved manufacturer, of required shade and colour complete as per manufacturer’s specifications

Fine dressing of the ground

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing precoated galvanized iron profile sheets (size, shapeand pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05 %) total coated thickness with zinc coating 120 grams per sqm as perIS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should haveprotective guard film of 25 microns minimum to avoid scratches duringtransportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Finishing with Deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers’ specifications Painting steel work with deluxe multi surface paint of required shade to give an even shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.80litre/10sqm of approved brand and manufacture

Providing and fixing of false ceiling with ACP sheet under frame work of precoated sheet of roofing of viewing decks with self drilling screws complete job

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels (Area of slab over 0.5 sqm) Granite of any colour or shade 18mm thick

Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite Work

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more

Centering and shuttering including strutting, propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platforms.

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength confirming to IS:4454 part-1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover

Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meters lead.

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement.1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement: 3 fine sand) as per standard design. In 75x75 mm deep chase.

Providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers:

Providing and fixing G.I. pipes complete with G.I. fittings excluding trenching and refilling etc. (external work) 15 mm dia. nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings excluding trenching and refilling etc. (external work) 20 mm dia. nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing Tee, including cutting and threading the pipe etc. complete 25 to 40 mm nominal bore

Providing and fixing brass bib cock of approved quality 15 mm nominal bore

Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding and joints filled with acid and/or alkali resisting cement as per IS:4457, complete as per direction of Engineer-in-charge In flooring on a bed of 10mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand)

Providing and Laying of PVC rigid water pipe 150mm dia laid over 1:5:10 ( 1 cement :5 Coarse Sand : 10 Stone aggregate 40mm nominal size) confirming to IS 13592 of 4.50 minimun pressure including necessay fixing with hardening solution and fittings if any. It wil also include encasing of pipe with cement concrete 1:3:6 (1 cement :3 Coarse Sand : 6 Stone aggregate 20mm nominal size) Size 40cm x30cm cross section

Supplying and fixing C.I. cover without frame for manholes: 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg.

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form work for: Foundations, footings, bases for columns

Providing and fixing Glass mossaic tiles at finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design, fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge:

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and curing complete

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angles 40x40x6mm for diagonal braces

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete.50 mm thick with 20mm nominal size stone aggregate

Supply ,installation ,testing and commissioning of Central Jet, 16 mm orifice, in brass construction conforming to IS standards and as per directions of engineer in charge with a jet height of 5 m

Supply ,installation ,testing and commisioning of Central Dome, 1.5 m dia made of 50 mm Extruded aluminium pipe 50 mm dia, having 40 numbers brass nozzlesconforming to IS standards and as per directions of engineer in charge , with a jet height of 2.5 m

Supply ,insallation ,testing and commisioning of Outside Drop Ring, 1.8 m dia made of 50 mm dia extruded aluminium pipes , having 48 numbers brass nozzles conforming to IS standards and as per directions of engineer in charge with a jet height of 1.3 m.

Supply ,instalation ,testing and commisioning of Peripheral Dome. 600 mm dia made of 50 mm dia extruded aluminium pipe, each having 20 nos brass nozzles conforming to IS standards and as per directions of engineer in charge with a jet height of 1.2 m.

Supply ,installation ,testing and commisioningof Brass columnar jet with a jet height of 1.5 m

Supply , Instalation <testing and commisioning of Central Jet, 16 mm orifice, in brass construction with conforming to IS standards and as per directions of engineer in charge a jet height of 4 m

Supply, instalation ,testing and commisioning of Central Dome, 1.3 m dia made of 50mm dia extruded aluminium pipe , having 34 numbers brass nozzles,conforming to IS standards and as per directions of engineer in charge with a jet height of 2 m

Supply ,instalation ,testing and commisioning of Outside Drop Ring, 1.5 m dia made of 50mm extruded aluminium pipe, having 40 numbers brass nozzles conforming to IS standards and as per directions of engineer in charge with a jet height of 1.1 m.

Supply , Instalation ,testing and comisioning of Peripheral Dome. 450 mm dia made of 50 mm dia extruded aluminium pipe, each having 16 nos brass nozzles conforming to IS standards and as per directions of engineer in charge with a jet height of 1 m.

Supply ,instalation ,testing and commisioning ofBrass Columnar Jet conforming to IS standards and as per directions of engineer in charge with a jet height of 1.1 m.

Providing and fixing of Submersible pump 5 hp,SS Suction mesh cover , base plate with fixing arrangements conforming to IS standards and as per directions of engineer in charge

Providing and Fixing of Submersible pump 3 hp ,SS Suction mesh cover base plate with fixing arrangements,conforming to IS standards and as per directions of engineer in charge

Providing and fixing of Submersible pump of 2 hp, SS suction mesh cover base plate with fixing arrangement conforming to IS standards and as per directions of engineer in charge

Providing and fixing of GI Manifold100 NB x 2 m long heavy duty

Providing and fixingFast acting solenoid valve, in SS construction with 24 volt DC coil conforming to IS standards and as per directions of engineer in charge

Providing and fixing of GM control Valve 32 mm conforming to IS standards and as per directions of engineer in charge

Providing and fixing GM control valve 25 mm; conforming to IS standards and as per directions of engineer in charge

Providing and Fixing of uPVC pipe of 40 mm,10 kgf/sq. Cm

Providing and fixing of uPVC pipe 32 mm, 10 kgf/sq.cm rating as feeder pipes

Providing and fixing of LED light, 21 watt (RGB), IP 68, in noryl construction conforming to IS standards and as per directions of engineer in charge

Providing and fixing Electrical panel for pumps as per the requirement conforming to IS standards .

Providing and fixing of Master control panel for solenoid valve and LED lights conforming to IS standards and as per directions of engineer in charge

Providind and fixing of PC controller conforming to IS standards and as per directions of engineer in charge

Providing and fixing of FFC controller

Providing and fixing of Cable 2.5 sq.mm x 3 core flat;

Providing and fixing of Cable 1.5 sq.mm x 2 core flexible cable,

Providing and fixing of Cable 1.5 sq.mm x 4 core flexible cable,

Providing and fixing of Speaker 200 watt of approved brand as per directions of Engieer incharge

Providing and fixing of Amplifier 500 watt of Approved brand as per direction of Engineer in charge

supply , instalation testing and commisioning of DVD player conforming to IS standards and as per directions of engineer in charge

PVC conduit 63 mm uPVC pipe with fittings complete heavy duty

PVC conduit of 50 mm uPVC pipe with fittings complete

Providing, laying, testing and commissioning of Chemical earthing ,aintance free earthing and back filling of the same for installation of 30 mtrs long 14.2 mm dia stainless steel copper electrodes filled with chemical compound complete job including GI strip/ wire as required

Operation and Maintainance of fountain for three years from date of completion all inclusive

Media filter minimum 40 cusec capacity on water source with all allied accessories complete

Programming of songs (40 minutes) as per the directions of Engineer in charge

Ashok Kumar Gupta