PROVN OF HARDSTANDING AND REPAIR RECTIFICATION OF DRAINAGE SEWARAGE SYSTEM AT BACK SIDE OF QTR OF TYPE II BLOCK PROVN OF WAITING SHED INFRONT OF RASHMI AT ITR RESIDENTIAL COLONY PROVN OF FOOTPATH AT NEW DSC LINE AT ITR PROVN OF PAVER BLOCK AND CERTA

Amount

NOTE (Applicable for all items) :- The bidders/contractors are advised to read tender document & all corrigendum / amendments and General conditions of contracts before entrying/quoting the rates.

Excavating in Post holes (or similiar holes ) each n exc 0.5 cum including getting out the excavated soft/loose soil, then returning,filling the soil as required in layers not exceeding 25cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto 1.5 m.complete all as specified and directed.

M&L for cement concrete 1:3:6 graded stone aggregate 20 mm nominal size for post hole, foundation, mass concrete, etc. complete all as specified and directed.

M&L for Steel work in built up tubular Hot finished welded type tubes (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position including welding and bolted with special shaped washers etc. complete.

Supply and fixing of pre-painted hot-dip galvalume aluminum-zinc alloy metallic coated trapezoidal profile steel sheet 0.50 mm thick (Total Coated Thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, atmospheric classification category 4, coating class AZ150 of an approved colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as directed.

Supply and fixing of pre-painted hot-dip galvalume aluminum-zinc alloy metallic coated plain steel sheet 0.50 mm thick (Total Coated Thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, atmospheric classification category 4, coating class AZ150 of an approved colour having tensile strength of 550 Mpa as in ridges/facia and similar work, fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as directed.

M&L for Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works.

M&L Polished Granite stone flooring in required design and patterns, with 15-18 mm thick stone slab over 20 mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with whitecement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc.all complete as specified and as directed by the Engineer-in-Charge. Note - Polished Granite stone slab will be of colour Black, Cherry/Ruby Red or equivalent as approved by GE.

M&L for heavy duty pre-polished pavement tiles of size 300 mm x 300 mm x 8-10 mm thick as in footpath/ hardstanding over and includung filling joint with white/ coloured cement to match complete all as specified & directed.

M&L for cement concrete 1:3:6 graded stone aggregate 20 mm nominal size for sub base all as per specified and directed

M&L for providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in?charge, (Note- For payment purpose, only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

M&L for Brick work with flyash bricks straight or curved on plan exc 6m mean radius ,in superstructure above plinth level up to floor five level built in Cement mortar 1:4 (1 cement : 4 coarse sand) directed.

M&L for 15 mm cement plaster in two coats under layer 10 mm thick with cement mortar 1:5 and a top layer 5 mm thick with cement mortar 1:3 mixed with WPC as per manufacturer instruction and finish the surface even and smooth without using extra cement. Note: WPC shall be measured and paid separately.

Supply only liquid water proofing compound.

M & L for Finishing walls with Acrylic Smooth exterior paint of required shade : over New work (Two or more coat) weather coat applied @ 1.67 ltr/10 sqm over and including a priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

M&L 10 mm cement plaster of CM (1:6) and finish the surface even and smooth without using extra cement complete all as specified and directed.

M&L 5 mm cement plaster on ceiling with cement mortar (1:3) and finish the surface even and smooth without using extra cement complete all as specified and directed.

M&L for applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

M&L for applying distempering (OBD)Two coats on new work wall and ceiling over and incl one coat of alkali resistant primer with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete incl preparation of surface, as per manufacturer's specification.

M & L for Reinforced cement concrete (nominal mix) in Type B-1, 1:2:4 (20 mm graded aggregate) in Columns, pillars, piers, posts and struts.

M & L for Reinforced cement concrete (nominal mix) in Type B-1, 1:2:4 (20 mm graded aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span.

M & L for Reinforced cement concrete (nominal mix) in Type B0 1:2:4 (12.5mm graded aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete, all as specified.

M & L for Mild steel TMT bars (Fe 500D) 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

All as per Sl Item No 22 above but 6mm to 8mm dia. in stirrups, spacers and binders.

Use and waste formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.

M&l for Centering and shuttering including strutting, propping etc. and removal of form work for :Columns, piers, abutments, pillars, posts and struts

M&L for Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform

Use and waste formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. including brushing neat cement slurry with 3.0 kgs of cement per sqm all as specified and directed.

M&L for Providing and laying in position 50mm thick cement concrete of 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) as in subbase to received tile including roughening of existing concrete complete all as specified and as directed.

M & L Paving vitrified parking tiles 300 mm x 300 mm x 8 to 10 mm thick (heavy duty), set, jointed and pointed in neat cement slurry with white cement and pigmentsas in footpath including 20mm thick screed bed in CM (1:4) complete all as specified and directed.

Earth work in surface excavation all kind of soil not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed.

M&L for 150 mm thick back filling of Moorum for pitching including supplying of required materials and consolidation etc as directed.

M&L for Chequerred precast cement concrete tiles 300mm x300mm x22-25 mm thick Medium shade pigment using 50% white cement 50% Grey cement in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, over and including 20 mm thick screed bed with cement mortar 1:4 (1 cement: 4 coarse sand). complete all as spd and directed.

M&L for Providing and laying 60 mm thickness machine pressed precast cement concrete paver block of M-35 grade confirming to IS 15658-2006 with approved colour, design, pattern, factory made, chamfered edge in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction.

M&L for Providing and laying in position cement concrete of specified grade 1:2:4 graded stone aggregate 20mm nominal size for cooping all as per direction.

Earth work in excavation by mechanichal means (Hydraulic excavator) in foundation trenches or drains (not exceeding 1.5m in width or 10sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m.

M&L for Providing and laying in position cement concrete1:4:8 graded stone aggregate 40mm nominal size for drain sub base, under paver block, etc. complete all as per specified and direced.

M&L for Providing and laying in position cement concrete 1:2:4 (graded stone aggregate 20mm nominal size in surface channels and drains, etc

M&L bricks work with flyash bricks, straight or curved on pl;an to any radius in half brick walls built in CM 1:6 complete all as specified & directed.

M&L 12mm cement plaster of mix 1:4 (1 cement : 4 fine sand) and finish the surface even and smooth without using extra cement complete all as specified and directed.

M&L for Providing and laying in position RCC 1:2:4 (nominal mix) with stone aggregate 20mm nominal size for cover slab, excluding the cost of centering, shuttering, finishing and reinforcement complete all as per required.

M&L for Steel reinforcement for RCC work ready to use "cut and bend" rebars of approved make from factory/workshop to construction site including placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of Grade Fe-500D or more.

S&F 100mm dia HDPE double wall corrugated SN 8 underground drainage/sewar pipes, confirming to IS7328, single socketed in any length jointed with solvent cement laid in trenches or floors etc complete all as specified and as directed.

S&F 150mm dia HDPE double wall corrugated SN 8 underground drainage/sewar pipes, confirming to IS7328, single socketed in any length jointed with solvent cement laid in trenches or floors etc complete all as specified and as directed.

Providing and laying cement concrete 1:4:8 graded stone aggregate 40mm nominal size) all-round S,.W. pipes including bed concrete 150 mm thick for 100mm dia HDPE double wall corrugated pipe

Providing and laying cement concrete 1:4:8 graded stone aggregate 40mm nominal size) all-round S,.W. pipes including bed concrete 150 mm thick for 150mm dia HDPE double wall corrugated pipe

Making connection (For pipes 100 to 250 mm diameter) of drain or sewer line with existing manhole including breaking into and making good the walls, floor with cement concrete 1:2:4 mix (1cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 ( 1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc, complete.

M&L vitrified floor tiles (double charge) of size 600mm x 600mm thickness of tiles as per manufacturer instruction in all colours and shades, laid over and including 20mm thick cement mortar 1:4, jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. complete all as specified and directed.

Material & Labour for providing and fixing stainless steel (Grade 304) hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the same with necessary accessories & etc., of required size as spcified.

Material & Labour for providing and fixing 3mm thick ACP board, plate etc., including buffing, polishing and making curvature (where ever required) including fixing the same with necessary accessories & etc of required size as spcified.

S&F factory made Knee Chair (Gym) of 100 mm dia MS pipe 3 mm thick with 100 micron epoxy coating over outer surface of pipe. Back rest shall be made of moulded hollow PVC sheet 5 mm thick of size 300 mm x 250 mm. Seat shall be made of moulded PVC of size 280 mm x 280 mm and rest of other parts shall be provided as shown on Drg No. AGE/BLS/06/2023-24 Sh No. 01/01 complying the standared size / dimentions as available in market including necessary foundation with RCC 1:2:4, Type-B1, designed as per manufacturer's instruction and fixing with and including required size of MS base plate, nut bolt, washers, etc. The knee chair shall be Self lubricating bearing for easy maintenance complete all as per manufacturer's specification and directed. Note : MS TMT bar, formwork, etc. shall included in quoted rate.

S&F factory made Cycle (Gym) of 40 mm dia MS pipe 3mm thick with 100 micron epoxy coating over outer surface of pipe. Seat shall be made of moulded PVC 3 mm thick of size (100 -300) mm x 250 mm and rest of other parts shall be provided as shown on Drg No. AGE/BLS/05/2023-24 Sh No. 01/01 complying the standared size / dimentions as available in market including necessary foundation with RCC 1:2:4, Type-B1, designed as per manufacturer's instruction and fixing with and including required size of MS base plate, nut bolt, washers, etc. The Cycle (Gym) shall be Self lubricating bearing for easy maintenance complete all as per manufacturer's specification and directed. Note : MS TMT bar, formwork, etc. shall included in quoted rate.

S&F factory made Cross walker (Gym) of 100 mm dia MS pipe 3mm thick with 100 micron epoxy coating over outer surface of pipe. Foot rest shall be made of moulded PVC sheet 3 mm thick of size 100 mm x 300 mm and rest of other parts shall be provided as shown on Drg No. AGE/BLS/03/2023-24 Sh No. 01/01 complying the standared size / dimentions as available in market including necessary foundation with RCC 1:2:4, Type-B1, designed as per manufacturer's instruction and fixing with and including required size of MS base plate, nut bolt, washers, etc. The Cross walker (Gym) shall be Self lubricating bearing for easy maintenance complete all as per manufacturer's specification and directed. Note : MS TMT bar, formwork, etc. shall included in quoted rate.

S&F factory made Shoulder Press (Gym) of 100 mm dia MS pipe 3mm thick with 100 micron epoxy coating over outer surface of pipe. Back rest and Seat shall be made of moulded hollow PVC sheet 5 mm thick of size 300 mm x 250 mm and rest of other parts shall be provided as shown on Drg No. AGE/BLS/01/2023-24 Sh No. 01/01 complying the standared size / dimentions as available in market including necessary foundation with RCC 1:2:4, Type-B1, designed as per manufacturer's instruction and fixing with and including required size of MS base plate, nut bolt, washers, etc. The Shoulder Press (Gym) shall be Self lubricating bearing for easy maintenance complete all as per manufacturer's specification and directed. Note : MS TMT bar, formwork, etc. shall included in quoted rate.

S&F factory made Air waler (Gym) of 100 mm dia MS pipe 3mm thick with 100 micron epoxy coatingover outer surface of pipe. Foot rest shall be made of moulded hollow PVC sheet 3 mm thick of size 100 mm x 300 mm and rest of other parts shall be provided as shown on Drg No. AGE/BLS/04/2023-24 Sh No. 01/01 complying the standared size / dimentions as available in market including necessary foundation with RCC 1:2:4, Type-B1, designed as per manufacturer's instruction and fixing with and including required size of MS base plate, nut bolt, washers, etc. The Air waler (Gym) shall be Self lubricating bearing for easy maintenance complete all as per manufacturer's specification and directed. Note : MS TMT bar, formwork, etc. shall included in quoted rate.

S&F factory made Leg Press Double (Gym) of 100 mm dia MS pipe 3mm thick with 100 micron epoxy coatingover outer surface of pipe. Back rest shall be made of moulded hollow PVC sheet 5 mm thick of size 300 mm x 250 mm. Seat shall be made of moulded PVC of size 280 mm x 280 mm and rest of other parts shall be provided as shown on Drg No. AGE/BLS/02/2023-24 Sh No. 01/01 complying the standared size / dimentions as available in market including necessary foundation with RCC 1:2:4, Type-B1, designed as per manufacturer's instruction and fixing with and including required size of MS base plate, nut bolt, washers, etc. The Leg Press Double (Gym) shall be Self lubricating bearing for easy maintenance complete all as per manufacturer's specification and directed. Note : MS TMT bar, formwork, etc. shall included in quoted rate.

M&L point wiring for one light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable as main wire drawing through surface / recessed medium class PVC conduit of suitable size and 1.5 sq.mm.FRLS PVC insulated copper conductor single core cable as earth wire etc. as required.

Supplying and embedding 32 mm dia G.I. pipe (medium class) in pole collar/ foundation (during casting) for cable entry including bending the pipe to the required shape complete as required.

Supply & fix round/square shaped LED Downlight 9 W to deliver high efficiency superior quality with pressure die cast aluminium housing for improve life and efficiency , opal acrylic diffuser for spot-free and uniform lighting.

Supply, connecting and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6.0 sq mm 2 core including connection cable glands, aluminium lugs etc all as specified and as directed.

Laying of one number PVC insulated and PVC sheathed XLPE power cable of 1.1 KV grade of size upto 35 sq.mm direct in ground including excavation, sand cushioning, protective covering(bricks) and refilling the trench etc and making good disturbed surfaces of floors,ground etc. as required and as directed.

jlenterprise

MS BEHERA SANITARY AND HARDWARE

KRISHNA ENTERPRISES

R.B.Construction

ANAND CHANDRA DAS

M/s D.K Mukherjee & Co

M/SNeelachal Enterprises

Bidder Name

KRISHNA ENTERPRISES

R.B.Construction

MS BEHERA SANITARY AND HARDWARE

ARIN AND COMPANY

M/SNeelachal Enterprises

ANAND CHANDRA DAS

jlenterprise

M/s D.K Mukherjee & Co