Construction of New Toilet Block at Nehru Memorial Collage Mansaal Govt Collage Mansa

Amount

Carriage of Surkhi, sand, bajri, ballast, stone, boulders, kankar, building rubbish

Fine sand Lead 164 KM

6 km to 40 km

41 km to 60 km

61 km to 150 km

150 km to 164 km

Ghaggar sand Lead 314 KM

6km to 40 km

41 km to 60 km

61 km to 150 km

151 km to 314 km

Bajri Lead 314 KM

6km to 40 km

41 km to 60 km

61 km to 150 km

151 km to 314 km

Earth work in excavation in foundation treanches etc in all kinds of soil where pick jumper work is not envolved and not exceeding 2.0 mtr depth including dressing of bottom and sides of treanches stacking the excavation and subsequent around masonary in 15 cm layers with compaction including disposal of all surace as directed with in lead of 30 mtr.

Earth filling :-

Earth filling under floors with surplus ordinary soil or soil containing gravel or kankar upto 40 % excavated from foundation and taken only from outside the building plinth in 15 cm layers including remaining watering and consolidating lead up to 30 mtrs.

Centring and shuttering for sides and soffits of beam, beams launchings girders bressumers, lintels

Centring and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc.

Cement concrete 1:8:16 with stone ballast 40mm gauge.using concrete mixer volumetric type.

Reinforced cement concrete M-20 with cement @375/kg per cum hand mixed but excluding steel reinforcement centring and shuttering in superstructure.

Damp proof course 4 cm thick of cement concrete 1: 2: 4 with two coats of bitumen 20/30 penetration @ 1.65 kg per sqm laid hot and sanded.

First class burnt brick work laid in cement sand mortar 1:5 in foundation

First class burnt brick work laid in cement sand mortar 1:5 in first storey upto 4 metres above plinth level.

Terracing consiting of tiles 22.86x11.43x3.83cm laid over 25 mm mud plaster 7.5 cm mud filling on another laver of 25mm mud plaster including two coats of bitumen laid hot at 1.65 Kg/sqm top of RCC slab including grouting with cement sand mortar 1:4 and top surface to be left clean after wire brushing etc.

Providing and fixing cast iron 100mm dia,rain water pipe with screw and wooden plugs fixed on wall-face, including filling joints with spun yarn and cement mortar 1:2 excluding head and shoe etc.

Providing and fixing cast iron head for rain water pipe on wooden plugs fixed on wall-face including filling the joints with spun yarn and cement mortar 1:2.

Providing and fixing cast iron shoe for rain water pipe on wooden plugs fixed on wall face including filling the joints with spun yarn and cement mortar 1:2.

Top khurra 0.6m x 0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50mm thick cement concrete 1:8:16.

Bottom Khurra on ground 1.2m x 0.6m consisting of brick on-edge laid in cement mortar 1:3 over 75mm cement concrete 1:8:16 including 12.5mm thick cement plaster 1:3

Base course of floor consisting of 100mm thick cement concrete 1:8:16 and 100mm sand filling.

Providing and laying Rectified Porcelain floor tiles 400x400mm or more (thickness to be specified by the manufacturer) of premium quality conforming to IS:15622 of approved make in all colours laid on 20mm thick bed of Cement Mortar 1:4 (1 Cement : 4 Fine sand) for new flooring complete Rectified tiles have finished edges allowing them to be placed closer together for a narrower grout joint as opposed to other tiles and are more expensive. Unlike typical factory-edged tile, rectified tile is cut to size after the firing process. This process creates a precise, 90 degree angle edge and, as a result, can be laid with a tighter grout joint than un rectified tile. It gives a smooth, sophisticated and continuous look to the floor. Using a rectified tile allows you to place the tiles much closer together using tighter joint spacing. This makes the grout less visible as there is actually less grout used. When a wide space is used between tiles, the grout becomes a distinct part of the design and if the grout does not blend well with the tiles it can create a less than professional looking finish. In addition, the grout can easily become soiled and discoloured over time and will detract from the look of the tile itself.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 200 x 300 mm as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement: 4 fine sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

12.5mm thick cement plaster 1:2

Cement pointing 1:2 deep variety.

White washing (Three coat)

Finishing walls with exterior decorative cement based paint such as snowcem, robbiacem etc. two coats to give an even shade.

Applying pink primer including painting 2 coats excluding priming coat with synthetic enemel paint in all shades on wood work metallic or plastered

Hollock wood doors shutter windows shutter including hinges, screws, chocks, cheats, stops cords etc. complete fixed in position.

Panelled, glazed or glazed and panelled(Double leaf)

35mm thick

Cost of Aluminium fittings complete for doors,windows such as tower bolts, handless and screw etc. for these fittings (Excluding sliding bolt)

For shutter area above 0.50 sqm

Cold twisted deformed (Ribbed/ Tor Steel Bar) Bars Fe 500 grade as per IS 1786-1985, for R.C.C works, where not including in the complete rate of RCC including bending and placing in position complete

Supply & Fixing of pressed steel frames (Chowkats) consisting of 18 gauge (1.25mm) thick steel sheet of the specified section(standard design latest) including iron lugs (hold fasts) iron hinges, confirming to P.W.D. specifications including bolts for fixing stops, lock-notch provision for receiving tower bolts, Hydraulic spring and finished with one priming coat of approved quality, fixed in position, including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:2:4 for lugs complete.

Doors and windows frame of size 118mm x 60mm with 40 mm wide single rebate weighing 3.43 kg per meter.

Wiring in PVC insulated copper conductor single core FRLS cable (ISI marked), 1100volts grade to be laid in heavy gauge welded conduit pipe 20 mm/25 mm dia (1.6mm thick) ISI marked,recessed in wall etc., complete with powder coated/anodized concealed metal boxes required for having electronic fan regulators (socket size), bell push, electronic buzzer, 3pin 6Amp., 3pin 16/20 Amp. Sockets and 6 Amp./16/20Amp. Swithces (flush piano type accessories) etc.and covered with brown bakelite white glazed translucent backside painted sheet 3mm thick etc., & including the cost of flush piano type switches/sockets, step type electronic fan regulator 100 watts, PVC connector (For Fan Box and Electronic Buzzer), PVC Bush, Steel Hooks, Circular Inspection Box (Recessed Type and Deep Type) conduit pipe & copper wire and other petty material etc. including the cost of cutting and filling up of chases:-

Wiring fan point with sheet metal fan box (shapehexagonal & sheet thickness not less than 1.60 mm) in PVC insulated copper conductor single core FRLS cable (ISI marked) overall 1.5 sq. mm, 1100volts grade with step type electronic fan regulator 100watts (socket size)

Wiring light point in PVC insulated copper conductor single core FRLS cable (ISI marked) overall 1.5 sq. mm, 1100volts grade.

Wiring 3 pin 6 Amp. wall socket point in PVC insulated copper conductor single core FRLS cable (ISI marked) overall 1.5 sq. mm, 1100volts grade complete with bonding to existing earth with PVC insulated copper conductor single core FRLS cable (ISI marked) overall 1 sq. mm, 1100volts grade.

Wiring 3 pin plug 16/20 Amp.

Non Schedule Items

Providing & fixing electric fan & regulator etc.

Providing & fixing Tube Light fitting 40 Wx1.20 M. Long on wall

Providing & fixing LED 15W

Providing fixing exuast fan including shutter compleate in all respects

External Sewerage

Providing, laying in trenches to correct gradient and alignment and jointing of UPVC pipes having ISI specification IS:15328-2003 class-SN-8 marked make Supreme, Finolex, Kissan, Jain, Prince or equivalent good on them and laying the same in trenches to correct alignment and gradients, cutting and jointing, testing for water tightness and making good the leakages and defects including cost of specials (Specials and Solvent should be of same make as that of pipes) complete in all respects.

110 mm o/d pipes (for External sewar pipe )

Construction of brick masonry inspection chambers size as given below up to 0.60 metre average depth in 1:5 cement sand mortar, lime concrete with 40 per cent lime mortar 2:3 in foundation, cement concrete 1:2:4 benching 12.50 mm thick cement plaster 1:2 with a floating coat of 1 mm thick of neat cement, R.C.C. 1:2:4 slabs 100 mm thick cement concrete topping 50 mm thick with 455 mm x 455mm, 455 mm x 610 mm inside light duty C.I. inspection chamber cover and frame (Weight as per I.S.I specifications) painted with 3 coats of black bitumastic paint conforming to I.S.I complete as per standard design.

Size 450 mm x 450 mm inside with RCC 455 mm x 455 mm cover and frame light duty double seal

Providing and fixing in position SWR UPVC soil waste vent or antisyphonage pipes as per IS -13592 of approved make (to the approval of Engineer-in-charge)including cutting, jointing, wastage, but excluding cost of lead jointing.

Type B

110 mm o/d SWR UPVC pipe line laid complete

90 mm o/d SWR UPVC pipe line laid complete

Providing and fixing in position SWR UPVC specials for soil waste vent or anti syphonage pipes as per as per IS - 14735 of approved make (to the approval of Engineer-in-charge) including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining.

For 110 mm o/d pipes

Bend Plain

Collar

For 75 mm o/d pipes

Bend Plain

Collar

P trap /Floor trap 75mm x75mm

Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with Grating 150 mm x 150 mm , cover and frame clear opening 300 mm x 300 mm and out of side size 330 mm x 330 mm and chamber including cost of all bricks work in cement mortar 1:5 cement concrete 1:2:4 in coping around cover and frame etc. as per standard design minimum depth of water should be 150 mm with a minimum seal 50 mm.

100 mm internal Diameter S.W. Gully trap with H.C.I. grating and cast iron cover weighing approximately 7.26 kg. and frame clear opening 300 mm x 300 mm and out of side size 330 mm x 330 mm

Internal Water Supply

Providing, laying, jointing, fixing and testing ISI Marked G.I. Pipe (as per IS 1239) B- Class Premium make such as (Jindal Hisar) including cost of specials (such as tees, bends, sockets, elbows etc.), painting with anti corrosive bitumastic paint, testing,cutting trading inside building complete

Providing, fixing and jointing G.I Union Couplings (of approved make with the approval of EIC) as per IS 1879 in G.I. Pipe lines complete in all respect.

15 mm i/d G.I. Union

20 mm i/d G.I. Union

25 mm i/d G.I. Union

Providing, fixing and jointing Brass Ball valves screwed with SS/BRASS ball & spindle & Teflon seats, on G.I. Pipe lines including all carriages complete.

25 mm i/d Brass Ball valves

Painting G.I. Pipes and Specials with synthetic enamel Paint in all shades as per I.S.I. specification on existing or new work, two coats paints including cleaning rubbing surface, etc.

15 mm & 20 mm i/d G.I. Pipe

25 mm & 32 mm i/d G.I. Pipe

Cutting holes up to 23 cm square through B.B. in cement walls or stone masonry wall in cement for pipes, and making good the same & finishing according to existing finish where required.

Through wall 11.43 cm thick

Through wall 22.86 cm thick

Cutting chase in brick walls in cement or in floor for embedding G.I. or C.I pipes line and making good the same to its original condition. Size 75 mm x 75 mm (15 mm+25 mm)

Saintary Installation

Providing and fixing in position Chinaware Indian Orissa water closet size 580 mm of approved make (to the approval of the Engineer-in-charge) consisting of 10 ltr. PVC flushing cistern including cost of PVC long bend 32 mm dia complete in all respect and to the intire satisfaction of engineer in charge

Providing and fixing in position Chinaware European type water closet P trap or S trap of approved make (to the approval of the Engineer-in-charge) consisting of 10 ltr. PVC flushing cistern, PVC short bend 32 mm dia including cost of seat cover complete in all respect and to the entire satisfaction of Engineer-in-charge.

Providing and fixing jet spray with 2'-6" long PVC pipe with PTMT nut

Providing and fixing in position vitreous Chinaware white large flat back or angular lipped front urinal 610 mm high of approved make (to the approval of the Engineer-in- charge) (610 mm x 410 mm x 380 mm) consisting of C.P. waste 32 mm dia and C.P. brass spreader, complete.

Providing and fixing PVC waste pipe 32 mm i/d of approved make (to the approval of Engineer-in-charge) complete in all respect.

Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge) consisting of C.P. brass waste 32 mm dia with one C.P. brass pillar tap complete in all respect.

Size 550 mm x 400 mm

Providing and fixing vitreous chinaware standard pedestal of approved make (to the approval of Engineer-in-charge) for wash hand basin complete in all respect.

Providing & Fixing in position 5 mm thick bevelled edge mirror of superior glass (of approved make) complete with 4 mm thick hard board backing fixed in with rawl plugs 50 mm , C.P. brass screws and washers complete in all respect (as required by the Engineer-in- Charge) - Size 600 mm x 450 mm.

Providing & Fixing in position C.P. Brass flange of approved make (to the approval of Engineer-in-charge) under various fixtures complete in all respect.

Providing & Fixing in position C.P. Brass extension piece 25 mm long to 50 mm long of approved make (to the approval of Engineer- in-charge) with various fixtures complete in all respect.

Providing & Fixing in position C.P. Brass Hexa Nipple 15 mm of approved make (to the approval of Engineer-in-charge) complete in all respect.

Providing & Fixing in position 15 mm i/d bib cock of approved make (to the approval of Engineer-in-charge) complete in all respect.

C.P. brass Bib cock long nose/ long body without flange

C.P. brass Bib cock without flange

Providing & Fixing in position stop cock / Angle valve of approved make (to the approval of Engineer-in-charge) complete in all respect.

C.P. Brass 15 mm Angle valve without flange

C.P. Brass 15 mm Concealed stop cock with flange.

Providing & fixing in position PVC flexible tube connection of approved make (to the approval of Engineer-in-charge) complete in all respect - PVC tube connection of size 15 mm x 375 mm with PTMT nut

Providing and fixing in position automatic brass Ball Cock in tanks.

Providing & placing in position on terrace (at all floor levels) HDPE water storage tanks of approved make (to the approval of Engineer - in-charge) with cover with suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fittings and base support for tank - Double Layer Tanks

1000 Litres capacity

Providing and fixing in position G.I. Tank Nipple of approved make (to the approval of Engineer-in-charge) in PVC Water storage tanks complete in all respect.

G.I. tank nipple 25 mm i/d

Providing and fixing in position vitreous Chinaware white channel of approved make (to the approval of Engineer-in-charge) of size 600 mm x 100 mm including laying and fixing in cement concrete 1:2:4 complete in all respect.

CONSTRUCTION OF SEPTIC TANK & SOACKAGE PIT

Excavation in Soil (any type) using Hydraulic Excavator CK 90 Excavation with hydraulic excavator of 0.9 cum bucket capacity including cutting trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, including all lifts andcombind lead up to 60mtr

Shuttering for faces of concrete foundations and foundation beam & plinth beam (vertical or battering)

Centring and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc.

Cement Concrete 1:8:16 with 40mm gauge stone aggregate.

Cement Concrete 1:2:4 with stone ballast or shingle.

Reinforced cement concrete M-25 with cement @425/kg per cum hand mixed but excluding steel reinforcement centring and shuttering in superstructure.

Suplying & laying dry Brick bats.

First class burnt brick work laid in cement sand mortar 1:5 in first storey upto 4 metres above plinth level.

12.5mm thick cement plaster 1:2

Cement Rendering on palster 1mm thick

Cold twisted deformed (ribbed/ tor steel) Bars Fe 415 grade as per IS 1786-1985 for R.C.C. works, where not included in the complete rate of R.C.C. including bending, binding, and placing in position complete.

Boring hand pump in soil with admixture of shingle

above 75mm dia but not exceeding 100mm i/d bore.

Proving & fixing 560mm ,500 mm,450 mm internal diameter circular or 450 mm x 600 mm clear inside opening rectangula RCC manhole cover & frame ISI marked as per IS 12592-2002 including carriage from the store of Engineer -in -charge to site of work loading unloading including stacking and setting the same to correct lines over manholes including cement conc copping (M20) around the frame etc dia of steel for lifting hook is 16 mm (for EHD and HD)

Providing orange colour safety footrest of minimum 6mm thick plastic encapsulated as per IS:10910 on 12mm dia steel bar confirming to IS: 1786 having minimun cross section as 23mm x 25mm and over all minimum length 263mm and width as 165mm with minimum 112mm space between protruted legs having 2mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specification and having manufacturer's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x15x11.5cm cement concrete block 1:2:4 (1 cement: 2 sand: 4 stone aggragate) complete as per design.each

Non Schedule Items

Filling Crasher in bore hole