138WE/L-18/2020-21

Amount

Dismantling plain or corrugated steel sheeting any guage thickness including nanital or similar pattern complete all as specified and as directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling wall/floor and ceiling boards (fiber, pulp, inlsulation,,etc) or insulation boards/slabs/blankets ,any thickness including covered fillets complete all as specified and directed.

Dismantlng framed work in wooden fillets, rails, posts, rafters, purlins, grids for ceiling & wall panelling etc under 40 Sq.cm in secton complete all as specified and directed.

Dismantling timber scantling over 40Sqcm in section (unframed) in any position complete all as specified and as directed.

Demolition of brick work or stone boulder masonary built in mud morter complete all as specified and directed.

Demolition of brick work or stone boulder masonary built in cement morter complete all as specified and directed.

Demolition of un-reinforced cement concrete in ground floor and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition), complete all as specified and as directed by Engineer-In-Charge.

Demolition of cement concrete in any description and any position not otherwise specifically provided, complete all as specified and directed

Dismantling floor, hearth or wall tiling including wall cement mortar bedding (But not backing ) and rubbish of premises, complete all specified.

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc.laid bedded and pointed in any mortar, complete all as specified.

Demolition of bricks (laid flat or on edge) or interlocking tiles in floors, channels, kerbes, aprons, etc laid dry of laid dry and pointed, complete all as specified.

Taking down mud plaster on brick or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc, complete all as specified.

Taking down cement plaster / raised pointing on brick or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc, complete all as specified and directed.

Taking down steel / PPR tubing ( 20mm bore) and connections in any position including cleaning for refixing or removal to store, complete all as specified.

Demolition and breaking up drain pipes ( salt glazedware, AC,reinfoced concrete, PVC pipe) of internal dia upto100 mm bore, set in cement mortar and taking out of trenches if required, complete all as specified.

M&l for PCC type D-2(1:4:8) using 40mm graded crushed aggregate as mass conc and filling of foundation , complete all as specified and as directed.

Providing Cement concrete (1:2:4) type B1 (using 20 mm graded stone aggregate) as in lintels upto 1.5m clear span , cills, steps and other similar bands , plinth courses, parapets and railings upto 60 cm in height , coping , kneelers, spex stones, complete all as specified and as directed.

Mild steel TMT bars10mm dia and over, cut length, bent to shape required , including cranking , bending spirally for hooping for coloumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to, complete all as specified and as directed.

All as per item ser No 20 above but 6 to 8mm dia as in stirups complete all as specified and directed.

M&L for pre cast block masonry set in CM 1:6 & casted in cement concrete type C-1 (1:3:6) using 20mm graded curshed stone agg complete all as specified and directed.

M&L for 15mm thick rendering on other than fair faces of brick works finished even and smooth (without using extra cement) in cement mortar 1:6 complete all as specified and as directed.

M&L for 10 mm thick rendering on fair faces of brick works finished even and smooth without using extra cement in cement mortar 1: 4 complete all as specified and as directed.

M&L Old size brickwork with subclass ‘B’ bricks straight or curved on plan exc 6 m mean radius and built in mud mortar, complete all as specified & directed.

All as per srl item ser No 25 above but except bricks, complete all as specified and as directed by Engineer-In-Charge.

M&L for 25mm thick mud plaster on rigid walls, partitions etc surfaces except rubble masonary(in one coat) complete all as specified and as directed.

M&L for preparation of new surface of mud plaster and applying three coat of cement base paint, complete all as specified & directed.

supply only Integral water proofing compound, complete all as specified and as directed.

M&L for 2nd class soft wood clean sawn timber fixed as in scatling fixed with nails, complete all as specified and as directed.

Ditto as per item no.30 but except timber, complete all as specified and as directed.

S & F rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates conforming to FE-410 - W(grade E-250) quality 'A', complete all as specified and as directed.

S&F 0.63mm thick plain galvanised mild steel sheeting as in ridges hi, valley gutters drip and straight flashings (length and girth as fixed) with L or J hooks or coach screws with grade of zinc coating 275, complete all as specified and as directed.

S&F 0.63mm thick Galvanised corrugated mild steel sheeting with two corrugations side lap,fixed withcoach screws and washers in roofs walls etc. with grade of zine coating 275, complete all as specified and as directed.

M&L Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors,balusters,nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or FE 310-0, complete all as specified and directed.

M & L for 75mm PCC 1:3:6 type C-2 using 20mm graded aggregate as in sub base of floor complete all as specified and directed.

M & L for 50 mm PCC 1:3:6 type C-2 using 20mm graded aggregate as plinth protection finished even and smooth with out using extra cement, complete all as specified and directed.

M&L Forming Contraction (Dummy) joints 50 mm deep x 10mm wide, filled with sealing compound Grade 'A' in plinth protection, complete all as specified and directed.

M&L PCC 1:2:4, 25 mm thick type B0 using 12.5mm graded stone aggregate as in floor finished even and fair with out using extra cement, complete all as specified and directed.

M&L for Machine cut Kota stone slab flooring 18-25 mm thick over cement screed bed 20mm thick in CM 1:6, set and jointed in neat cement slurry laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing, complete all as specified and directed.

M&L for Chequred cement concrete tiles 20cm X 20cm X 25mm thick, set ,pointed & jointed in neat cement slurry in floors polished with grey cement & pigments .Layed over 20mm thick cement screed base (1:6) and all as directed by Engr-in - charge.

M&L for Non skid coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.11Sqm and nexc .18 Sqm in floor etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match the shade of tiles over screed bed with CM (1:6) 15mm thick laying floor tiles complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.06 and nexc .11 sqm in floor etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match the shade of tiles over screed bed with CM (1:6) 15mm thick laying floor tiles complete all as specified and directed.

M&L for Glazed ceramic coloured tiles in vertical surfaces 350 x 250 x 7mm /450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match the shade of tiles over over 10mm thick CM (1:4) in dado/skirting tiles complete all as specified and directed.

Taking down chowkats / frames with shutters (without taking off shutters from the frames) area n'exc 1.5 Sqm each complete all as directed by Engr-in-charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exceeding 1.5 Sqm and not exceeding 4 Sqm each complete all as directed by Engr-in-charge..

Taking down shutters of any description area exceeding 1 Sqm and not exceeding 2 Sqm each complete all as directed by Engr-in-charge.

Taking down shutters of area not exceeding 1.0 sqm complete all as directed by Engr-in-charge

Hacking old broken glass (any thick ness, size, quality or description) from wooden panes or stone, concrete or brick surrounds, glazed with oil putty or fixed with beads, complete all as specified and as directed .

Taking down shutters of any description area not exceeding 1 Sqm each, resecuring or easing & adjusting and refixing in the same opening complete all as directed by Engr-in-charge.

Taking down shutters of any description area exceeding 1 Sqm and not exceeding 2 Sqm each,resecuring or easing & adjusting and refixing in the same opening, complete all as specified and directed.

S&F 2nd class soft wood plain, solid, straight chowkets and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete(Glass shall be measured Seperately, complete all as specified and directed.

S&F mild steel work as in hold fasts and similar work confirming to Fe-290 or Gd -E 165, complete all as specified and directed.

M&L for treating wooden chowkats surface of any description n exc 10 cm in width or girth with black bituminus paint in two coats, complete all as specified and directed.

M&L for preparing surfaces and treating small articles such as stop, cover, gully gratings, MS hold fasts , end of post chowkat etc area n exc 0.1 sqm each and treated with tar or coal tar black paint , complete all as specified and directed.

Material & labour for PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) as in hold fast , bed block and like, complete all as specified and as directed by the Engr-in-Charge.

S&F 35mm hardwood Glazed and skelton shutter, open and prapared to receive the glass, gauze etc.(without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc. complete all as specified and as directed by the Engr-in-Charge.

S&F for 40 mm thick Flush shutters, solid core construction ,with block board core and plywood face panels commercial type on both sides , Supply and fixed to chowkats , complete all as directed by Engr-in-charge.

S&F 35 mm soft wood Glazed and skelton shutter, open and prapared to receive the glass, gauze etc.(without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc. (Glass / Wiremesh should be measured seperately) complete all as specified and as directed by the Engr-in-Charge..

S&F MS framedwork such as grills, gratings etc with ends of bars shouldered and/or rivited or forged in spikes, framed guard bars, barred iron doors, ledders framed balsters walk ways railings frame work of water tanks and similar work confirming to Fe-290, Gde-E-165, complete all as specified and as directed.

M&L French polishing new/old untreated surface of wood or wood based surface of any width or girth or any description,including cleaning and preparing the surface including a coat of wood filler on old surface with two or more coats complete all as specified and as directed

S&F Steel windows (frame with shutter) with side hung shutters including projecting type hinges with steel handle ,and steel peg stay,complete with glazing bars,dovetailed or welded (Glass shall be measured Seperately)complete all as specified and directed by Engineer-in-Charge.

M&L sheet glass 3mm thick ordinalry quality and glazing with oil putty or wooden beads in square not exc 0.50 sqm in each pane, complete all as specified and as directed.

S&FGalvanised mild steel wire cloth ,0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and as directed.

S&F in repairs Galvanised mild steel wire cloth ,0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and as directed.

S&F mild steel butt hinges, medium weight cold rolled 100mm size, complete all as specified and as directed.

S&F 150mm long aluminium anodized, barrel tower bolt of extruded section, complete all as specified and as directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized, complete all as specified and as directed.

S&F mild steel butt hinges, medium weight cold rolled 75mm size, complete all as specified and as directed.

S&F 100mm long aluminium anodized, barrel tower bolt of extruded section, complete all as specified and as directed.

S&F 100mm size extruded aluminium alloy handles, fabricated type, anodized, complete all as specified and as directed.

M&L sheet glass 3mm thick ordinalry quality and glazing with aluminium beeds in square not exc 0.50 sqm in each pane, complete all as specified and as directed.

S&F in repair 300mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and as directed.

S&F in repair 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed, complete all as specified and as directed

S&F in repair 19mm dia mild steel, chromium plated curtain rods, with brackets, end bulbs, complete all as specified and as directed by Engr-in-charge.

M&L for 2nd class soft wood clean sawn as in battens for grids of ceiling & lining fixed with nails exc 13 sqcm and n exc 25 sqcm in section,complete all as specified and as directed.

M&L for 2nd class soft wood clean sawn as in beeding for edges of Ceiling ,lining ,or wooden flooring work fixed with nails exc 6 sqcm and n exc 13 sqcm in section,complete all as specified and as directed.

M&L for covered fillets of standard hard board 6mm thick and 40mm wide and fixing with screws, complete all as specified and as directed.

M&L for 6mm thick (5 ply) plywood grade BWR type BB as in walling panelling fixed with nails to timber frame work, complete all as specified and as directed.

All as item No 79 above but on ceiling, complete all as specified and as directed.

M&L for 9mm thick prelaminated particle board interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with screws to timber frame work as in wall panelling, shelves/boarding complete all as specified and as directed.

All as item No 82 above but on ceiling, complete all as specified and as directed.

S & F 500 litres capacity rotational moulded polyethylene water storage tanks with cover (Cylindrical vertical, with closed top), hoisted and fixed in position all as specified in SSR Part I including taking down old one as directed, complete all as specified and as directed.

3 layer PP-R Polypropylene random copolymer pipes 20mm dia SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot and cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to wall, ceiling or in floors etc, complete all as specified and as directed.

S&F in repairs PP-R gate valves 20 mm dia (brass insert) as per requirement of the site, complete all as specified and as directed.

S&F in repairs PP-R Ball valves (brass insert) 20 mm dia as per requirement of the site, complete all as specified and as directed.

S & F in repair Vitreous China wash basin, white, flat back, size 450 x 300mm including cutting for and pinning in ends of brackets or erecting stand but inclusive of fixing of supply and waste pipe, complete all as specified and as directed.

S&F in repairs Vitreous China bowl Urinal, flat back, size of 465x355x265mm white (Minimum) with grating and union for discharge pipe pipe (excluding flushing cistern, flush pipe and waste pipe), complete all as specified and as directed.

S&F in repairs Vitreous China squatting pan 'Orissa' pattern,size 580x440 mm white with integral foot rests (excluding flushng cistern and flush pipe) and all as directed by Engneer-n Charge.

S&F in repairs, 10 litres capacity PVC valveless syphonic action type, flushing cistern (ISI marked), low level with inlet, ball valve, float bracket & flush pipe, complete all as specified & directed.

S & F in repair 15 mm bore pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe, complete all as specified and as directed.

S&F in repairs Angle stop valves, cast copper alloy, screwed down high pressure with crutch or butter fly handle, fancy type, chromium plated with long shank and cup (concealed type), 15mm bore dia of pipe, complete all as directed by Engr-in-charge.

S&F flush waste pipe of polyethylene of low or high density or PVC ,32 mmdia for urinal/wash basin/ flush tankfixed in repairs, complete all as directed by Engr-in-charge.

S&F in repairs PVC connection pipe suitable for connecting flushing cistern and WHB etc 450mm long, complete all as specified and directed.

S & F in repairs, waste coupling of PTMT 32mm bore for urinal / wash basin (Half or full threaded ) (Minimum Weight 45 grams), complete all as specified and as directed.

S&F in repairs bib tap cast copper alloy chromium plated butterfly handle screwed down screwed for iron pipe completed (15mm dia tap), complete all as specified and as directed.

S & F in repairs, PVC (SWR) 75 mm dia, floor trap, plain with grating including jointing to waste pipe with solvent cement, complete all as specified and as directed.

S & F in repair grating doom 125mm dia with waste hole of PTMT (mim weight 40 grms) all as directed by the Engr-in-Charge.

S&F in repairs Soap dish vitreous china white fixed to plugs with chromium plated brass screws , complete all as specified and as directed.

S & F in repair Stainless steel sink with draining board,made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x 330mm x 160mm, complete all as specified and as directed.

S & F 110 mm dia, PVC (SWR) pipes, single socketed, in any length with rubber ring joints laid in trenches or in floors all as specified and as directed by the Engineer - in - Charge.

S & F 75 mm dia, PVC (SWR) pipes, single socketed, in any length with rubber ring joints laid in trenches or in floors all as specified and as directed by the Engineer - in - Charge.

PCC 1:3:6 type C-2 (40mm gradded aggergate) bed to drain pipe incl packing under and haunching against side after they are laid and tested for 110mm dia pipe , complete all as specified and as directed.

M&L dressed granite or trap Kerb stones roughly squared stones of size 20cm x 30 cm ,so that the maximum depression from a straight edge held against the dressed surface shall noot exceed 6mm for top and exposed surfaces of sides and 20mm for the rest of surfaces jointed in cement mortar 1:6 and struck finish ( rate included for removal of old damaged curb stones of any description), complete all as specified and as directed.

M&L for Cement concrete type D-2,1:4:8 (40mm graded aggregate) 100 mm thick as in sub -floors ,sub- bases ,floors and pavings etc, complete all as specified and as directed.

M&L machine pressed precast concrete interlocking paver block any shape and size polished with grey cement and pigment confirming to IS 15658-2006 of 80mm thickiness M-40 grade ,complete all as specified and as directed by Engr-in-Charge.

M&L sand filling (50 mm average thickness) under floors in foundations and for laying Interlocking paver blocks including watering and consolidation, complete all as specified and as directed by Engr-in-Charge.

M&L for preperation of new Brick,Concrete,Wall and Stone surface of any description descripton and applying two coat of synthetic enamal paint over a coat of primer, complete all as specified and as directed.

M&L for preperation of existing treatment on Brick,Concrete,Wall and Stone surface of any description descripton and applying one coat of synthetic enamal paint, complete all as specified and as directed.

M & L for preparation of new steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer, complete all as directed and specified.

M&L for prep of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of primer(chalk whiting) complete all as specified and as directed.

M&L for prep of newly plastered surfaces of walls and applying three coats of white wash, complete all as specified and as directed.

M&L for preperation of new wood or wood based surface of any description over 10cm width or girth and applying two coat of synthetic enamal paint over a coat of pink primer, complete all as specified and as directed.

M&L for preperation of existing treatment on steel / CGI sheets of any descripton and applying one coat of synthetic enamal paint (galvanisatin should be removed if required) ,complete all as specified and as directed.

M&L for preperation of old wooden joinery, wall & ceiling surface surface any description over 10cm in width or girth and applaying one coat of synthetic enamal paint complete all as specified and as directed.

M&L for preperation of old plastered wall surface of any description and applying two coat of white wash, complete all as specified and as directed.

M&L for preperation of old plastered wall surface of any description and applying one coat of cement based paint, complete all as specified and as directed.

M&L for vetrified ceramic tiles 10mm thick (light shade ) (square/rectangular) polished, area of each tiles not exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over screed bed with CM (1:4) 15mm thick for laying floor tiles all as specified and directed.

S&F anodised aluminium snap grid framework for falsle ceiling including Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I.flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long and Perforated particle board/ tiles 12mm thick for insulation and accoustic purposes, 60x60 cm in size, fixed with nails to timber frameworkorwith staples on snap grid complete all as specified complete all as specified and directed. Make : SAINT GOBAIN/Gyprox/Everest

S & F in repair vitreous China wash basin, white, flat back, size 630 x 450 mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe, complete all as specified and directed.

M&L Anodised aluminium powder coating of any colour(Thickness or powder coating not less than 50 micron).window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.), complete all as specified and directed.

S & F Anodised aluminium door shutters of aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc, complete all as specified and directed.

S & Fsheet glass 4.8 mm thick ordinalry quality and glazing with oil putty or aluminium beads in square n.exc 0.50 Sqm in each pane, complete all as specified and directed.

M&l for PCC type D-2(1:4:8) using 40mm graded crushed aggregate as mass conc and filling of foundation complete all as specified and directed.

M&L Walling of random rubble stone masonry, uncoursed well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and directed.

Supply only broken brick for loose filling ,of gauge 80mm to 150 mm graded complete all as specified and directed.

M&L form work to soffits of suspended flat sabs such as roof slabs ,floor slabs,landings and similar works (smooth finished flat surface of concrete) not exceding 200mm thick (Horrizontal or sloping) , complete all as specified and directed.

M&L form work to fair finshed edges of concrete at flats, treads breaks in floors, window cills, concrete failings, openings in concrete walls, floor and roofs n.exe 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20 cm wide, complete all as specified and directed.

M&L RCC type B1 1:2:4 (20 mm grade aggregate ) in Slabs supported on walls ,beams and columns,in floors, roofs,landings, balconies, canopies,deck slabs and in shelves and the like, complete all as specified and directed.

M&L for precast cement concrete Type C1, 1:3:6 (20mm graded aggregate) in lindings, cover slabs (for manholes etc), chullah hoods, chhajja, water troughs, shelves and similar articles with plain faces, setting in CM 1:6, complete all as specified and as directed .

M&L excavation in trenches in hard /dence soil not exceeding 1.5 m wide and not exceeding 1.5 m depth, complete all as specified and directed.

S&F salt -glazed stoneware drain pipes150mm internal diameter laid in trenches and jointed, complete all as specified and directed.

S & F bends and taper bends for salt -glazed stoneware drain pipes150mm internal diameter laid in trenches and jointed, complete all as specified and directed.

M & L Concrete bed in 1:3:6 type C2 (40mm graded stone agg) to drain pipe of bore 150 mm including packing under ,and haunching against the sides of pipe after they laid and tested, complete all as specified and directed.

Returning,filling in ,including spreading,levelling ,watering and well ramming in layers not exe 25cm, complete all as specified and directed.

Removing excavated soil n exc 50m and depositing where deirected at a level n exc 1.50m above the starting point, complete all as specified and directed.

Extra over stone walling for hammer dressing for Granite or Trap store n'exc 40mm deep when held against edge complete all as specified and as directed.

Taking down carefully aluminium / copper point wiring light/fan/socket or power complete including unscrewing from board fitting and fixture such as switches, sockets, ceiling roses, lamp holders, brackets, pendent holder , light fittings , regulators, distribution/ Meter boards, MCBs etc and making good the distturbed surface matching with existing specifications complete all as specified and directed.

Point wiring for one light point or fan point controlled by one switch with 1.50 Sqmm, PVC insulated, unsheathed, FRLS single core, multi-stranded, copper conductor cable, 1100 Volts fire resistance ISI, drawn in and including PVC casing and capping, fire resistance, ISI marked, fixed surfaces of walls and ceilings, terminated in and including rectangular PVC board for mounting fitting/ switches/ sockets and 1.50 Sqmm, copper conductor, multi-stranded, FRLS as earth continuity wire connected to earth terminal, including making good to disturbed surface as matching to existing descriptions/ specifications, complete all as specified and as directed.

Description all as per serial item No-140.00 here-in-before but for one 5 Amps 3 pin socket outlet on same board, complete all as specified and as directed.

Description all as per serial item No- 140.00 here-in-before but for one 5 Amps 3 pin socket outlet on independent board, complete all as specified and as directed.

Point wiring on independent board with 2.50 Sqmm, PVC insulated, unsheathed, FRLS single core, multi-stranded, copper conductor cable, 1100 Volts, drawn in and including PVC casing and capping, fire resistance, ISI marked, fixed surfaces of walls and ceilings, terminated in and including rectangular PVC board for mounting fitting/ switches/ sockets and 2.5 Sqmm, copper conductor, multi-stranded, FRLS as earth continuity wire connected to earth terminal, including making good to disturbed surface as matching to existing descriptions/ specifications, complete all as specified and as directed.

S&F Switch piano, flush type, single pole, one way, 5 Amps 240 Volts complete all as specified and as directed. Make : ANCHOR/PLAZA/HAVELLS

S&F Switch socket combination 2 in 1, 3 pin 5 Amps, flush type universal complete all as specified and as directed. Make : ANCHOR/PLAZA

S&F Switch socket combination piano flush button single pole one way 5 pin 5/16 Amp, 240 Volts, complete all as specified and as directed. Make : ANCHOR/PLAZA

Ceiling rose, surface bakelite 65 x 50 mm two or three terminals including taking down, complete all as specified and directed. Make : ANCHOR/PHILIPS/HAVELLS/CROMPTON

S&F in replacement 2'x2' Recess/Surface mounting slimness (9 mm thin) in class LED Ceiling Panels white LED Luminaries white powder coated sheet housing LED front frame blends seamlessly with Ceiling layout of capacity 36 watt (2x2) LED extruded alluminium heat sink projected in false celing, with complete accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete. Make:Havells cat part No- ENDURASLIMPROPLUS2x2PLR28/36WLED857MOD & LEDDRIVER36V36WS or equivalent in Bajaj / Crompton / Philips/.

LED bulk head light fitting 1 x 10 watt , 230 volts, attractive wall/ ceiling mounted any type with white reflactor complete with all accessories prewired and including connecting up with twin core twisted flexible copper conductor cable complete all as specified and directed. Make: Havells cat part No RUGBYNEONFT10WLED760SSYMBOPC or equivalent in Bajaj/ Philips.

S&F for LED Light fitting incl LED tube light batten type 1 x 20 watt mounted on integrated sleek extruded polycarbonate LED channel with white acrylic cover suitable for 230 volt 50 Hz cool white colour bipin holder connector block etc complete will all accessorized internally prewired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete. Make: Havells cat part No- STOUTPLUS600BS20WLED857SPCWH or equivalent in Bajaj/ Crompton Greaves/ Philips.

Lamp holder, PVC/ Polycarbonate type with back plate, straight/ angular, suitable for batten fittings, including taking down, complete all as specified and directed. Make Havells / Kinjal / Anchor.

Taking down existing unserviceable/old DBs from any height and any make good complete including disconnection from existing MCBs/Isolator etc complete all as directed.

Factory made epoxy powder coated distribution board ,double door, triple pole and 4 ways (TPN MCB DB) with metal door (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper bus bar neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with one MCB TPN 415 V, 63 Amps, 10KA as incoming and 12 Nos, single pole, MCB 63 Amps, outgoing and conforming to IS : 8623 complete all as specified and directed.Make : Legrand Cat No. 607715 or equivalent of Havells/C&S

Sheet metal enclosures for distribution box for MCBs, Single pole and neutral, 8 way with, 240 Volts, double door, with 200 Amps rated bus bar blank plate complete all as specified and directed.

S&F sheet metal enclosures for distribution box for MCBs, Single pole and neutral, 12 way with, 240 Volts, double door, with 200 Amps rated bus bar blank plate complete all as specified and directed.

S&F MCB, triple pole and neutral (TPN ) 63 Apms, 415 Volts, connecting with copper lugs including taking down old one complete all as directed.

S&F single pole and neutral (SPN) MCB 40 Amps, 240 volts, 50 Hz AC, made from moulded self-existing thrmostate plastic and suitable 'C' curve 10 KA breaking capacity and terminal box suitable for 4 to 10 Sqmm cable complete, conforming to IS 8828 including taking donw old one all as specified and directed.

S&F distribution board, single pole and neutral (SPN) MCB 32 Amps, 240 volts, 50 Hz AC made from moulded self-existing thrmostate plastic and suitable 'C' curve 10 KA breaking capacity and terminal box suitable for 1.5 to 6 Sqmm cable complete conforming to IS 8828 incluiding taking down old one all as specified.

S&F of LED light energy saving and environmental friendly long life versatile pressure dia cast aluminium , IP66 street light of 48 watt 5700K 240 Volts single phase LED light suitable for 40 mm dia pipe for fixing on wall including connection with suitable size 3 core PVC cable complete all as specified and directed. Make: Havells cat part No ENDURAPEARLNEOSL48WLED757SASYTOPC or equivalent in Bajaj/ Philips/C&G.

S&F heavy duty five star rated Exhaust fan AC single phase 230 Volt of size 450 mm sweep with louvers shutters and connecting up including provision of cable from ceiling rose to connector of fan controlled by one way switch complete all as specified and directed. Make : Usha/Havells/Khaitan.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground.(earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr. Below ground level connecting to galvanised iron wire 4mm diaas earth lead by means of bolts, check nuts and washers of GI and earth strip protected by provision of GI pipe light grade, 20 mm bore including provn of concrete pit in PCC (1:2:4) type B-1 using 20mm graded crushed stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM ( weight not less than 4Kg/Sqm) and frame of angle iron 25 x 25 x 3mm with lugs 2 Nos and with 6mm dia MS bar handle made to shape, GI medium grade 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil,returning filling in and removal of surplus soil to a distance not exeeding 50 mtr, all as per electrical plate No 3 of SSR 2009 Part-I and connection all as specified and testing on completion. Note: The cost of excavation and earth work, PCC pit and pit covers, funnel and watering pipe, wire mesh, charcoal dust and common salt, 20mm dia, medium grade, GI pipe as protection to earth lead and earth lead as 4mm dia GI strip (main earthing lead from earth electrode to test point length not less than 7.5mtrs) shall be deemed included in the unit rate for earthing.

Sub main wiring for circuit/ submain wiring alongwith earth wire with two run of 6.0 Sqmm of fire resistance, PVC insulated copper conductor, single core cable, multi stranded, FRLS, ISI marked, 1100 Volts grade and one run of 4 Sqmm, FRLS, PVC insulated copper conductor, single core cable, multi stranded, ISI marked, 1100 Volts grade as earth wire connected to earth terminal, drawn in and including PVC casing and capping, fire resistance, ISI marked, fixed on surfaces of walls/ ceilings, including making good to disturbed surface matching to existing descriptions/ specifications, complete all as specified and directed. Make : Plaza/Havells/Finolex.

Taking down old unservicable LT U/G cable of 2/4 core 10/16 Sqmm to 25 sqmm , complete all as specified and directed.

Sand cushioning to protection of underground cables, laid 8 Cm before laying and 15 Cm after laying of cable, and punned to form an overall layer of 18 Cm thick, complete all as specified and directed. Note: Punned thickness shall be measured.

Supplying and laying un-reinforced precast concrete cable cover, Class LV, Type-I, flat, size 250mmx150mmx40mm, complete all as specified and directed.

XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with multi-standard aluminium conductor, 1100 volts grade, cross sectional area 25 Sqmm 4.0 core, laid in trenches or passing through pipes, including making necessary connections at both ends, complete all as specified and directed.

XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with multi-standard aluminium conductor, 1100 volts grade, cross sectional area 25 Sqmm 2.0 core, laid in trenches or passing through pipes, including making necessary connections at both ends, complete all as specified and directed.

SHARMA AND SONS CONSTRUCTION CO

Mehar Enterprises

ASHOK KUMAR SHARMA

M/S Praveen Kumar and Sons

ANJALI CONSTRUCTIONS

VIJAY ENTERPRISES

R B TRADERS