Proposed Relocation of Staff Clinic and HRD Office Renovation work 2nd floor, Service Block

Civil Works

Electrical Works

Item Rate BoQ

BoQ_Ver3.0

NIT No. TMC/ENG/Civ&Elect/StaffClinic/HRD/25-26/e-NIT/60 dated 24/02/2026

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

Providing making and supplying computer table made out of 19mm thick approved commercial ply for table top, mounted on the vertical side support of 19mm thick ply and drawer unit cabinet with 12mm thick ply appron as shown in drawing. The drawer cabinet made out of 19mm commercial ply for sides, shelves and shutters and drawers mounting with heavy duty sliding channel with ready mode key board drawer with heavy sliding channels, all edges shall be lipped with 6mm thick T.W. lipping patti or PVC edge beading matching with laminate. All exposed faces should be 1.0mm thick laminate of approved colour and make, non laminated area should be 0.80 mm thick white / off white laminate including necessary hinges, handle, multuporpose lock, ball catch etc. as per drawing and as specified and directed by Engineer-In-Charge. Computer table with all inner surface with 0.8 mm thick approved laminate

Providing making erecting partitions (partly glazed partly panneled or fully panneled) to required ht. With aluminium square pipe heavy duty section of 50mmx50mm X 2mm thick in 600mm sq. panel or as required at site the wooden panneling with 8 mm thick commercial plywood of approved make and quality on both sides of partition with 6mm groove with 1.00 mm thick approved colour laminate finish. The glazed portion teak wood 30mmx12mm bedding on both sides to the required shape skirting at bottom on both the sides to required shape and top patti with 125 x 20mm T.W.to required flap/or as filler between the wall/ceiling/flooring and partition. The glazed portion of the partition. The glazed portion of the partition shall have approved make/quality –plain/frosted/ one way5mm thick glass. Partition with laminate

Partly glazed/partly panneled.

Fully panneled.

Providing making and fixing in position counter consisting of top (all width 2inch-6 inch) made out of 25mm commercial ply of approved make supported on drawer unit of ht.2 inch -6 inch and vertical supports at regular internals as shown in drawing made out of 15mm thick approved commercial ply and the counter made above the table of required width and size with vertical divider all made out of 19mm thick approved commercial ply and 12mm thick approved commercial ply for front side of counter with approved laminate or 10mm teak wood lipping on all exposed edges and table top edges should be 1 ½ inch x1 ½ inch finishing with and approved colour and moulding plastic laminate 1.0mm thick for all exposed surface etc. all inside surface shall be 0.8mm thick approved laminate soft board of 12mm thick pasted with approved adhesive and covered with tepestery felt cloth of required colour including cost of all hardware like hinges, tower bolt, handles, knobs, computer ready-made keyboards, cable manager, CPU stand made by 19mm thick ply with approved laminate finish and locking arrangement with Godrej multipurpose lock etc. complete as specified and directed.

Providing and fixing cabinet made up of 19 mm. Commercial ply of approved make for top, bottom, sides and shelves and 8 mm thick commercial ply approved make for back side.Door shutter made up of 19mm thick commercial ply and All exposed surfaces including shelves for open type cabine should be laminated with 1.0mm thick approved plastic laminate sheet of required colour including all brass fittings such as hinges, tower bolts, ball catches, stopper, handle, knobs as per shown in drawing or approved by Engineer-In-Charge etc.and all exposed edges shiuld be 6mm thick lipping patti or PVD lipping patti matching with laminate finish, locking arrangement with Godrej multipurpose lock etc. All inside areas shall be .80mm thick approved colour laminate etc.all complete as specified and directed by Engineer-In-Charge. Cabinate with inner side 0.8 mm thick laminate ( White / Offwhite ) With shutter

Providing wood work with 1st class teak wood in frames for doors windows, ventilators, Air-condition frames, clear story window, false ceiling and partitions etc.wrought framed and fixed in position including applying one coat of approved wood primer to the exposed surfaces and tow coats of bitumastic paint to the surface of wood in contact with masonry/concrete etc.complete.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters Door shutters with locking arrangement 4 lever mortice lock with handle set of approved make. 35 mm thick

Providing and fixing door closer of Everite/Hyper make confirming to is 3564 (left or right) to the existing door shutter including cost of all other materials labour etc. all complete as specified and directed. Archies make hold open arm door closer

Rail for sliding door (set)

Providing and fixing curtain track of fancy type powder coated suspended from ceiling with rings for curtains to be provided at 5 inch intervals etc complete.

Removing the existing partitions/ doors and handing over the same at required place indicated by the engineer in charge. etc. complete.

Providing and Fixing wooden flooring in line & levelling including underlayment requirement like a vapor barrier and specific thickness of foam with all necessary allied works & taking out debris out of TMH premises

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main"T" runners to be suspended from ceiling using GI slotted cleats ofsize 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanisedbutterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mmcenter to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete forall heights as per specifications, drawings and as directed byEngineer-in-charge.

GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. a) Plain sheet

Providing and Fixing new Gypsum board false ceiling with GI frame work including providing necessary openings for light fixtures, diffusers, trap doors etc to be made as per layout drawings and as per EIC.

Providing and fixing in position suspended false ceiling system using 600x600 mm material fibre reinforced factory applied vinyl painted "ARMSTRONG" ceiling tiles (Armstrong ceiling systems) Tiles having 16/15 mm thick, and approved surface design and edge profile ( TEGULAR or equivalent) place in a suspended grid of size of 600 x 600 mm made of hot- dipped G.I. steel sections having an exposed surface capping of pre-finished bake polyester painted caoil wherein the main tee of size 24mm x 32 mm shall be suspended at 1200 mm centres along the length of ceiling with 4mm dia G.I wire with necessary level adjustments. The cross tees of size 24x27x1200mm shall be inserted in to slots between the main tees at 600mm centres and thereafter in direction vertical to the longer tees , cross tees of size 24mm x 24mm including providing necessary openings for light fixtures, diffusers, trap doors etc to be made as per layout drawings and as per EIC. The maint tees to be suspended from the ceiling/soffit with the help of metal dash fastners of 6mm x 50mm ,soffit clits of 25mm x 35 x 1.60mm and 4m dia G.I wire with galvanised spring steel levelling clips. the entire grid system shall be designed to bear a disturbuted load of minimum 15kg/sqm (only Armstrong false ceiling area will be measured for the purpose of payment) ARMSTRONG tile models of 'ELITE-16mm/' Fine Fissured - 16mm/Classic Lite-15mm'or other approval

Providing and fixing approved quality machine pressed phenol formal dehy de bonded commercial/marine ply wood of approved size and fixing the same with necessary nails/screws/adhesive in partition cupboard shelves/ktichen/cabinets/flush doors etc. at all floors and locations in quantities as required at site in following thickness including 6 mm thick T.W.lipping patti at all exposed edges with nails/screws/hardwares/adhesive wastage in cutting, transportation etc. complete all as directed by the Engineer-In-Charge. Commercial ply

12mm thick ply

19mm thick ply

Providing and fixing 1.0mm thick approved make laminate of required colour over existing surfaces along with the adhesive all as required specification design etc. complete as specified and directed by Engineer-In-Charge. 1.00 mm thick

Providing and fixing 12mm thick soft board pasted with approved adhesive and covered with tepestary felt cloth (Jute fibre) of required colour including removing old soft board if necessary and refixing etc. complete as specified and directed. Soft board with felt cloth

S.S. plate handle D type 150mm X 150mm

Providing and Fixing 12mm thick plain glass with 'D' bracket (With machine edge polishing)

Providing and Fixing S.S.heavy duty hinges of approved make-

Providing and Fixing Mirror 24 inch x 18 inch (Plastice frame)

Providing and fixing 600mm long s.s. towel rod of Jaquar make

CUDDAPAH :Providing & laying 25-30mm thick cuddapah stone slabs in platforms / sinks with all exposed edges machine cut double machine polished in true plane and level with matching cement paste curing finishing the joints neat etc. complete including making grooves in walls for fixing and making good the surfaces.making cutting for fixing waste cupling water inlets etc. ( disposing / taking away the debris outside the premises & disposing as per the guidlines of statutory authoritised. )

GRANITE: Providing and laying 18-20mm thick granite slab in required size and approved colour as per approved sample 1st quality for lift architraves / dado / flooring / sills / platform / sink / with all exposed edges machine cut double machine polished (mirror polish) laid over a bedding of cement mortar 1:3, 35mm thick in true plain curing finishing the joints making holes for wash basin / sinks coupling in slab if required etc. complete including making grooves in walls for fixing and making good the surface (excluding cuddapah platform) colours – Black/Red/Grey. ( disposing / taking away the debris outside the premises & disposing as per the guidlines of statutory authoritised. )

MOULDING :Labour charges for making moulding for granite slab as per approved sample with mirror polishing etc. complete all as per instruction by engineer in charge.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

VITRIFIED FLOOR TILES / DADO TILES Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600mm

Providing, laying, jointing, fitting & testing UPVC pipe SDR of heavy quality following dia for cold water distribution system of approved make (Prince, finolex, Supreme make) including all fittings required as per site requirement for concealed pipe laying by chasing in wall, floors and making good the same to the original condition and for open type of pipe laying and fixing in proper line & level with necessary PVC clamps wood packing etc. fixing the joints with proper solvent or threaded type fittings or press type fittings to make totally water proof joint with necessary testing etc. complete all as per specified and directed by Engineer in Charge. (work includes removing old fixtures also) 20mm n.b.

P.V.C. PIPES: Drain Line - Providing, laying, jointing, fitting testing heavy quality PVC pipes of Prince, Supreme etc. make & of required dia including all fittings required as per site requirement & laying the same at any floor levels including scaffolding all jointing materials & clamping in wooden blocks if required etc. complete as directed & specified by engineer in charge. 32mm

WASH BASIN : Providing & fixing best quality wash basin of approved colour & size with following items as specified.Providing & fixing white / colour glazed vitreous china ware wash basin of make Hindware with semi punched tap holes for fixing the tap in different position in the basin, mounting the set over a suitable C.I. bracket etc. as approved by & Fixing 32mm size C.P. / PVC brass/ a bottle trap with extension piece wall flanges (heavy quality) jointing with white Zinc & Spun yarn & fixing 15mm dia PVC water inlet connection of required length with C.P. brass unions at end & fixing 32mm dia C.P brass heavy quality waste coupling with C.P. brass ball chain & rubber plug & fixing 15mm C.P brass fancy stop cock including cost of jointing materials etc. as per requirement & Fixing C.P. brass 15mm dia fancy pillar tap or approved pillar tap of make,BMC approved including cost of jointing materials etc. Testing the entire system to the full satisfaction of the engineer in charge wash basin model No.10001/10004 of hindware. Parryware/Cera counter wash basin white colour

Item Rate BoQ

BoQ_Ver3.0

NIT No. TMC/ENG/Civ&Elect/StaffClinic/HRD/25-26/e-NIT/60 dated 24/02/2026

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

POINT WIRING :- Point wiring for light/fan/bell with ISI mark 3 x 1.5 sq.mm (P+N+E). FRLS PVC insulated copper conductor of Polycab / RRK /Finolex in surface/ recessed heavy class pvc casing capping/conduit of Presto-plast/sunwood /Precision make with Modular switch of Legrand-Myrius/MK-Blenze & Anchor make-ceiling rose/batten holder/slanting holder Boxes etc. with circuit labling/marking/ferruling complete.

Primary point upto 4 mtrs length

Primary point length 4 mtrs to 7 mtrs

Primary point length 7 mtrs to 10 mtrs

Secondary point Extending from Primary point upto 4 m

Half point on same board with 5A S/W and 5A Socket.

Concealing of 25mm dia. Pipe with surface finish.

Concealing of 6"X 6" Box or lower size with surface finish.

Concealing of upto 12"X 12" Box with surface finish.

Dismantling Electrical wiring, cabling and accessories :- Providing qualified Wireman and a helper with tools for carrying out dismantling the existing light, fan, bell, independent plug point wiring of all types with accessories and cable /switchgear in an approved manner as per instruction of Engineer Incharge and handing over all the removed material to Engineering Dept. by preparing list of material.

Supply & Installation of White Colour Legrand-Myrius Series /MK-Blenze Series Accessories with back box as per requirement of site conditions.

TV socket co-axial - 1 module with face plate and PVC back box

Bell Indicator with buzzer - 240V - Modular type

Blank plate -1 module

Supply & Installation of Legrand-Myrius /MK Metal boxes

1/2 -3 Module

4 Module

6 Module -

8 Module -

2 x 4 Module -

12/16 Module -

18 Module -

Supply & installation of surface Board Legrand-Myrius/MK-Blenze (inclusive of back box, surface plate & wiring)

6Amp Switch&Socket

6A socket-2 nos+6A switch 2 nos

6A socket-3 nos+20A switch Cat. No. 6730 75

16Amp Socket + 16A Switch with Indicator

Telephone Outlet with telephone I/O, back box and face plate in all respect (without telephone wire)

Supplying and fixing on wall PVC sun wood /prestplast heavy duty boards of following size

6 inch x 8 inch

8inch x 10inch

SUB MAINS Mains :- Providing Heavy duty PVC casing-caping/conduit of Precision make. Supplying and erecting mains with copper conductor PVC insulated FRLS of 1100 V AC grade Polycab/RRK/Finolex make wire with circuit labling/marking/ferruling complete.

2 x 1.5 sq mm -+ 1.5sqmm Earth wire

2 x 2.5 sq mm -+ 1.5sqmm Earth wire

2 x 4 sq mm -+ 2.5 sqmm Earth wire

Supply and Fixing Rigid PVC conduit Medium Mechanical Stress (MMS) with all fitting & fixing accessories Precision make

Supply and Fixing PVC Flexible Conduits Poly Proplyne (PP) with all fitting & fixing accessories Precision make

Supply and Fixing PVC Casing Caping with all fitting & fixing accessories Precision make

1inch dia 25mm x 12mm

Supply and Fixing of PVC Trunking /covering of following sizes

100 x 50 mm PVC trunking

50 x 50 mm PVC trunking

PVC/XLPE CABLE :- Armoured cables - supplying, laying, testing and commissioning of 1100 V AC grade PVC FRLS insulated ISI mark Poly- cab/RRK/Finolex Copper Conductor cable erected on wall,ceiling,column etc with appropriate size of GI spacers & saddlers screws etc complete in approved manner of following size . .

2 x 1.5 sq mm copper (Red color fire fire alarm system)

3 x 4 sq mm copper

Supplying, erecting, testing and commissioning of 1100 V AC PVC FRLS armoured 3 1/2 core Aluminium Conductor cable of Polycab/RRK/Finolex make erected on wall/beam/ceiling/shaft etc with appropriate size, along with saddlers,spacers complete with approved manner of following size . .

3 1/2 x 35 sq mm

Cable Glands - Double Compression with Termination:- Supplying and erecting heavy duty flange type brass cable glands for armoured cable with brass washers,rubber rings complete erected with cable ends & leads connected with proper size lugs.Make Comet/Braco/Dowells.

2 to 4 core 2.5/4/ 6 sq mm

3 to 4 core 25-50 sq mm

Earthing :- Supplying,installation of copper strip /bare wire of earthing system on wall /slab/column/beam along with clips etc including end connections with crimping type copper lugs complete in all respected and as directed by Eng-in-charge

14 SWG copper bare wire

8 SWG GI wire

Supplying and erecting following cable / wire with appropriate size casing caping or rigid PVC heavy guage pipe of approved make (Precision) with PVC accessories to make complete piping rigid, install in or wall / ceiling / concrete with PVC spacers, sadd clamps by suitable clips to complete the pipe erected etc as per Instruction of Engineer in charge.

RG 6 Coaxial cable

RG 11 Coaxial Cable

Erection/fixing & commissioning of departmently supplied fluorescent fixtures on

On wall/ceiling/false ceiling with all its accessories like J hooks and chain required to mount the same.

Distribution Boards Supply, installation, testing & commissioning DBs for mounting MCB/ELCB/Isolator - on wall complete.

SPN 12 way IP 43 with Metal door

TPN 4 way IP 43 with Metal door

TPN 8 way IP 43 with Metal door

SITC of Legrand DX3 make AC C Curve MCB of following sizes in provided enclosure and connected with leads on incoming and outgoing side duly completed in approved manner.

6 to 32 A SP MCB 10 KA

6 to 32 A TP MCB 10 KA

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

Providing ,fixing and commissioning of Legrand DX3 make RCBO

25A/32A FP - 300 mA

40A FP - 300 mA

63A FP - 300 mA

Cable end box for IP 43 DBs

SPN 8WAY DB

ETPN 4WAY DB

ETPN 8WAY DB

Telephone Wiring :- Supplying and laying 0.5 mm gauge unarmoured telephone wire D.O.T approved, make Dlink/Finolex/Digilink/Polycab through exisitng conduit/casing caping/cable tray.

Boxes - MS sheet to be used for fabrication of boxes, panel,cable end boxes,boards etc including cutting,bending, drilling,welding,riveting etc and painting one coat of red oxide and 2 coats of gray enamel paint etc complete.

S&C hylam sheet of 3 mm thick to be used for covering MS boxes etc including cutting,drilling,fixing with nut bolts/ screws cup washers etc complete as required and to the satisfaction of incharge with making necessary groove/ cutting for fixing electrical accessories.

SITC of conventional Fire Alarm Dectector with base make Apollo series 65 or equivalent.

SITC of analog telephone instrument make Panasonic Model KXTS 500 color Black

Supply Installation Testing and Commisisoning of Dome IP-Camera , 2 megapixel (1920 x 1080) resolution or better,Image sensor-1/2.8” 2MP CMOS progressive sensor Or Better, 0.03Lux (Color), 0Lux (B/W, IR LED on), 2.8mm fixed lens, Frame rate- 25fps controllable or better, H.265, H.264, MJPEG Multiple streaming, True WDR,Motion detection, Tampering, Defocus detection, View (90°/270°), Support memory card (Max. 128GB), Inbuilt IR viewable length 15m,Onvif Profile-S G, Protocol support-IPv4, IPv6, TCP/IP, UDP/IP, RTP(UDP), RTP(TCP), RTCP, RTSP, NTP, HTTP, HTTPS, SSL/TLS, DHCP, FTP, SMTP, ICMP, IGMP, SNMPv1/v2c/v3(MIB-2), ARP, DNS, DDNS, QoS, UPnP, Bonjour, LLDP,Security-Password protection, IP address filtering, HTTPS encryption, IEEE 802.1X network access control, Digest authentication, User access log,Interface-RJ 45, 100 Base TX or better,POE power, IP66, IK10, PoE, 12VDC,Metal Body, Back box, Certification-STQC, BIS, UL/ CE/ FCC/ NDAA.

SITC of CAT6 Cable in MMS PVC 20mm dai., 1.3mm thick Conduit with PVC saddle at equidistance of 1 meter on wall/ceiling in proper mannner, all PVC fitting & fixing accessories Precision make,Conduit colour:- graey/White, Cat cable colour:- Blue .

Filling-up of Financial Bid: Unless otherwise called for, any tender containing percentage below / above the estimated cost put to tender is liable to be rejected. All rates shall be quoted on the tender form by the tenderers in figures and words shall be accurately filled in, so that there is no discrepancy in the rates written in figures and in words. The amount for each item should be worked out and requisite totals given. However,

Please Enable Macros to View BoQ information

TATA MEMORIAL CENTRE

ENGINEERING DEPARTMENT

TECHNICAL BID DOCUMENTS CHECKLIST

NIT No :

Description

Address

Contact person

Telephone no.

Fax no.

E mail Id

GSTIN

Annual Income Tax return filed with I.T. Department

TIN, EPFO, ESIC, BOCW Welfare Board registration certificate, etc.

Letter of Transmittal

EMD in the form of Demand Draft / Pay Order / Banker’s cheque / Fixed Deposit Receipt (FDR), issued by a Scheduled Bank drawn in favour of Accounts Officer, TMC, Mumbai

Annual Turnover of latest five year ending in March 2024 duly certified by Chartered Accountant with Profit / Loss (Form A)

Financial turnover in Lakhs

Average last 3 consecutive years

Profit/Loss in Lakhs

Bank solvency certificate (Form B)

List of similar works carried as per letter of transmittal.

M/s. Company Name WO No. / LOI No / Agreement No. dated Subject Amount Rs. (Location of site)

M/s. Company Name WO No. / LOI No / Agreement No. dated Subject Amount Rs. (Location of site)

M/s. Company Name WO No. / LOI No / Agreement No. dated Subject Amount Rs. (Location of site)

List of Completed works (Form C).

List of works in Hand/ under Execution (Form D).

Client Performance Report (Form E)

Structure & Orgnization (Form F)

List of Technical & Administrative staff (Form G)

List of Plant & Equipments (Form H)

Declaration confirming the knowledge of site condition(Form I)

Details of court cases pending against tenderer (Form J)

NEFT Mandate Form – (Form K)

Undertaking Preference to Make in India – (Form L)

Date wise execution Program

Undertaking - the eligible similar work(s) have not been executed through another contractor

Undertaking - gone through the documents

Undertaking for downloaded the pre-bid clarifications

NIT (Stamp & Signed)

Make List (Stamp & Signed)

Electrical Contractor License