Provn and installation of 48V DC SMPS, 10 KVA UPS and misc equipment for NFS Node and other works at Military station Beas and Suranussi under GE Kapurthala

Amount

Supply, install, testing and commissioning of 7.5 KVA KOEL GREEN AIR COOLED SILENT DG SET comprising of KOEL make Air Cooled Diesel Engine model EA16-G1 (CPCB NORMS COMPLIANCE) 1500 RPM & 7.5 KVA KOEL Green make Alternator rated at 3 Phase, 415 Volts, 50 Hz; 0.8 p.f. @ 1500 RPM both mounted, and aligned on a common MS base frame complete with MS Fuel Tank, AMF Panel, Residential Exhaust Silencer, AVM Pads fitted on base frame,1 No.12 Volts DC Battery with Battery Leads, 1st fill of Lube Oil, all housed in Sound Proof Acoustic Enclosure as per CPCB norms complete with foundation for DG Set (as per OEM design) including brick work, PCC, plastering etc all as specified and directed by Engr in Charge. Make- Kirloskar/Ashoka Leyland/ Cummins or equivalent approved make comprising of the followings :-

The design of integral acoustic enclosure should be approved by National Physical laboratory as per central pollution control board(CPCB-II) latest regulation/norms with fuel tank, battery & standard (A) ENGINE- Air cooled diesel engine of at 1500 RPM capacity to match the 7.5 KVA alternator under NTP conditions with provision of 10 % over load for 1 hour in every 12 hours running confirming to BS 5514/ IS 10001/ 10002. (B) Exhaust piping of GI Med Grade size 50 to 80 mm dia shall be provided duly insulated with asbastos rope duly cladded with aluminium sheet. (C) CONTROL PANEL The control panel with aluminium bus bar, bottom entry and exit of cable, current transformer, set of control fuses, Multifunctional Meter, it should display time and date, Volts, Frequency, Current, KW, KWH, PF, RPM, Cumulative Run Hours, Oil Pressure, Coolant Temp, Charging current (DC Amp Meter). Emergency off, factory made floor mounted, totally enclosed, epoxy powder coated suitable for 7.5 KVA DG Set incl all necessary operating controlled devices as stated above and MCCBs as out going with protection fues for panel insturments duly wired with flexible copper conductor cable and cable connection with lugs/thimbles complete as per latest IS/BS and all as specified and directed.

(D) AMF PANEL ;- The AMF Panel suitable for 7.5 KVA DG Set factory made out of CRCA Steel 16 SWG Sheet floor mounted type and front operated type, totally enclosed dust, damp and vermin proof, all doors and joints will be suitable gasketed to form dust and vermin proof. The panel would be powder coated minium thickness of 50 microns, stove enameled paint finished after elaborate pre-treatment to form a long lasting characteristic. The control panel will be complete in all respect with fuses, wiring and labels etc, the following will be incorporated in the AMF Panel as per standard design/ specification in vogue :- a) Multifunctional meter digital (Amp+Volt+PF+Hz+KW=KWH) b) Alternator voltage monitor c) Main voltage monitor d) Ammeter Digital e) Voltmeter Digital f) Power fuse link h) Power fuse base j) Main power contactor - 3 pole k) DG Power contactor-3 pole l) Indicator lamps

m) MCB (for control ckt) n) Auxiliary Contactor o) Automatic battery 12 volt charger p) Terminal O/L relay q) Terminals (for control cable) Note :- The above specification can vary as per Company norms if supplied inbuilt/ open execution by the manufacturer of DG Set Make of engine : Greaves cotton/Cummins/Ashoka Leyland/Kirloskar. Make of alternator : Greaves cotton/Stamford/Kirloskar/Electric/Crompton Greaves Make of Acoustic Enclosure : Sudhir/Ashoka Leyland/Kirloskar Green Note:-(i) Pre-Commissioning test shall be carried out by IEM of HQ CE JZ, for which all arrangement of testing load and other accessories required for testing at site including DHPP and Lub Oil etc shall be arranged by contractor to the entire satisfaction of Eng-In--Charge and testing officer and rate quoted by the contractor deemed to include this provision.

Supply and fix Online UPS 10 KVA 3/1 360VDC- Input 415 AC Output 220 AC with Isolation Transformer (Inbuilt) Amron Quanta/Exide/Rocket 12 V 26 AH SMF Batteries for 60 minutes backup complete all as specified and directed by Engr in Charge. Make- Unitek or equivalent ISI Mark. Note for Item No 2 : The contractor will arrange visit of service engineer/ technical rep of Manufacturer to give presentation on technical details/ catalogues/ specification of above product i.e Online UPS to Engr in Charge & User Unit Auth Rep and take approval of User Unit and Engr in Charge before placing order for procurement of UPS & also before, supply and installation.

Supply and laying cable XLPE insulated screened PVC bedded LT cable, 1100 volts grade aluminium conductor of size 70 Sqmm 3.5 core

Excavation in trenches in soft/loose soil not exceeding 1.50 mtr wide and not exceeding 1.50 mtr in depth for laying of cables and getting out including trimming of sides complete all as specified and directed by Engineer-in-Charge.

Returing, filling in, including spreading, leveling watering and well ramming inlayers not exceeding 25 cms thick each layer compete all as specified and directed by Engineer-in-Charge.

Removal of surplus spoil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed by Engineer-in-charge.

Material and labour for sand cushioning with a layer of sand 8cm thick before laying of cable and 15 cm thick after laying of cable in trenches complete all as specified.

Material and labour for brick protection using old size sub class ‘B’ new bricks, laid flat dry but jointed, laid length wise perpendicular to the axis of cable all as specified and directed.

M & L for earthing with galvanized iron earth plate electrode 600mm x 600mm, 6mm thick buried directly in ground vertically in a earth pit not less than 2.25mtr below normal ground level with top edge of the plate not less than 1.5mtr below normal ground level connected to GI strip 32x6mm by means of GI bolts, nuts, check nuts and washers (earth plate covered with alternate layers of charcoal dust and common salt 15cm thick), GI strip 32x6mm protected by GI pipe medium grade 40 mm dia upto switch board and connected to main switch board including provision of GI pipe 20 mm dia medium grade watering pipe with funnel and wire mesh, all as shown in Electrical Plate No. 3 of SSR Part-I, including PCC chamber (1:3:6) using 20mm graded stone aggregate and CI cover and frame including all necessary excavation and earth work and taking out old earthing complete all as specified and directed by Engineer-in-charge

Supply, install, testing and commissioning Voltage stabilizer for automatic operation, three phase naturally oil cooled indoor type & designed for input variation between 340 V to 460 V with output voltage stabilized at 415 with accuracy ± 2.5% and speed of correction 8 Volts per second and of capacity 10 KVA Make- Volina/ IEC or equivalent

S&F sheet steel enclosure with single door vertical DB , flush/surface mounting for and incl MCCB/MCB’s fitted with bus bar, earth bar and neutral link 12 ways TPN 415 V comprising of (a) Incoming MCCB, 100 Amps, 4P, 25 kA -01 Nos (b) Outgoing MCB, 63 Amps, 4P, - 01 Nos (c) Outgoing MCB SP, 6-32 Amps - 08 Nos including fixing/grouting on existing wall with proper electrical connection all as specified and directed by Engr in Charge. Make of DB/MCBs - Havells/Indo asian/ Legrand or equivalent

S&F GI tubing light grade for encasing cables for mechanical protection, laid under plinth/floors/ roads/ path /culverts or fixed on walls/on poles by means of MS FI clamps with necessary bolts, nuts and washers all as specified of sizes 50mm bore

Supply and fixing in replacement sub main wiring with 4 single core PVC insulated cable with copper conductor stranded and sheathed of size 4 Sq mm in and including PVC casing caping of suitable size with 4 Sq mm copper earth wire to common earth and connected to earth dolly complete all as specified and directed. Note:- Five run of 4 sqmm cable and one run of casing and caping will be meadured as one unit of length Make of cable : Finolex/Havells/Plaza/Indo Asian.

M & L for chemical earthing with copper earth plate 90 x 60 x 5 mm & copper earth strip 32 x 6 mm as per IS:3043 (Code of practice for earthing) as specified and directed by Engr in Charge.

S & F Air termination, single pointed, copper rod 12 mm dia and 300mm long mounted on GI pipe 40mm dia light grade embedded in mass pcc all as specified and directed by Engr in Charge

S & F copper strip 25 x 3 mm with saddles and fixing screws etc for roof/down conductor above ground including jointing with rivets/ brazing etc all as specified and directed by Engr in Charge.

S&F test point terminal block made of gun metal or phosphorus bronze/ copper size 75 x 75 x 25 mm drilled and screwed including 3 Nos 8 mm dia 25 mm long hex head screw specified and directed by Engr in Charge.

S & F steel tubing,medium grade,galvanised with all fittings,laid in trenches or fixed to walls or poles for mechanical protection of earth strip/ holding Air termination rod etc complete of size 40 mm bore all as specified and directed by Engr in Charge.

M&L for PCC 1:2:4, type B1, using 20mm graded crushed stone aggregate as in bed block coping cells etc. all as specified for fixing of pipe for lightning arrester all as specified and directed by Engr in Charge.

Supply and install hi wall split units (Air Conditioner) indoor/outdoor complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality of capacity 1.5 TR BEE 3 star rated.Make- LG/Voltas/Carrier or equivalent.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 4 KVA . Make of Stabilizer - Volina/ V Guard or equivalent.

Supply and fix Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 A MCB Make- Havells/ Indo Asian/Legrad or equivalent.

Supply and install Online 48 VDC 150 Amps SMPS Based Uninterruptable supply (48 VDC- Output) (220 V AC- Input) with Isolation Transformer (Inbuilt) Amaron Quanta/Exide/Rocket 12 V 200 AH SMF Batteries complete for 60 minutes backup all as specified and directed by Engr in Charge. Make- Unitek or equivalent ISI Mark Note for Item No 24: The contractor will arrange visit of service engineer/ technical rep of Manufacturer to give presentation on technical details/ catalogues/ specification of above product i.e 48V DC SMPS to Engr in Charge & User Unit Auth Rep and take approval of User Unit and Engr in Charge before placing order, supply and installation.

Supply, laying & testing PVC insulated, PVC sheathed cable galvanized steel strip or wire armoured, electric control cables (Heavy duty) with stranded copper conductor of size 4 sq mm ,4 core, 1100 Volts grade all as specified and directed by Engr in Charge.

S & F Cable tray 14 SWG 100 mm Height and min 500 mm width ISI Mark all as specified and directed by Engr in Charge

M &L for Cement concrete 1:5:10 type E-2 using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified and directed by Engineer - in - Charge.

M&L for Brick work with sub class 'B' bricks using old size bricks straight or urved on plan exc 6m mean radious built in CM 1:6 etc complete all as specified and directed.

M&L for 15mm thick Rendering in CM 1:6 on brick work or concrete surfaces finished even and smooth etc complete all as specified and directed.

M&L preparing newly plasatered surfaces of walls and applying birla putty 1mm th to achieve smooth surfaces and applying two coats of Oil emulsion distemper over a coat of primer , complete all as directed by engineer-in-charge.

M&L for providing cement concrete type B-1, 1:2:4 (using 20 mm graded stone agg) as in lintels upto 1.5m clear span complete all as specified and directed by engr-in-charge.

M & L mild steel TMT bars10mm dia and over cut to length bent to shape required including cranking, hooking ends and binding with MS wire (annealed) not less than 0.90mm dia all as specified and directed by Engineer - in - Charge.

All as per item 32above but 5mm dia to 10mm dia as in stirrups.

Formwork to sides and soffits of beams, lintels, including supports, overhangs, etc. also splays between floors and beams, etc. for fair finished works

Supply and fix openable anodised aluminum door (frame and shutter) made out of hollow extruded aluminum sections as mentioned below:- Each door having 02 Nos D type handles, 02 Nos aluminum tower bolts 200mm size, hydraulic door closer, 04 Nos stainless steel butt hinges and one Mortice lock with duplicate key . Shutter to be partly glazed with 5mm thick, plain or tinted glass and partly paneled with 12 m thick prelaminated partilcle board and fixed with glazing clips, rubber beading/gasket, anodised aluminum beading, screws complete including provn of anodised aluminium grill on glazed and gauzed portion of size 25 mm x 25mm, 6mm dia , made out of matters or cages, lapped wire and fixed to aluminum frame work with U section and screws/other fixtures as required. Chowkat/Frame : 101.60 x 44.45 x 1.60 mm thick Shutter top and bottom rail : 114.30 x 44.45 x 1.55 mm th Shutter Middle Rail : 83.50 x 44.45 x 1.55 mm Shutter verticle style : 85 x 44.45 x 1.55 mm thick complete all as specified and directed by Engineer - in – Charge.

M & L Hardcore (broken bricks)of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for Cement concrete 100 mm thick, type D- 2, 1:4:8 (40mm graded aggregate) in flooring complete all as specified and directed.

M & L for Cement concrete 100 mm thick, type B-1, 1:2:4 (40mm graded aggregate) in flooring complete all as specified and directed.

S & F Mild Steel Works as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets (for securing wire mesh etc) including all necessary welding, drilling, bolting or reveting etc including embeding in concrete etc and similar work conforming to Fe Fe 290 Gde E 165.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, Soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm.

M&L Cement concrete Type D-2 1:2:4 (40mm graded aggregate) in foundations, filling and mass concrete.

M & L for preparation of new steel surfaces of width or girth exc 10 cm and applying two coats of synthetic enamel paint over a coat of red oxide.

S&F 0.63mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 fixed with L-type or J-type or cranked hook bolts in lieu of screws.

Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing

KAMAL AGGARWAL

L-7 Primewave Communications

DUGGAL CONSTRUCTION CO

J K AND COMPANY

R D Bansal