NIT No. 1100/TC/EinC/PWD/25-26

Excavation for all types and sizes of foundations, trenches and drains or for any other purpose including disposal of excavated stuff upto 1.5 m lift and lead upto 50m (at least 5m away from the excavated area), including dressing and leveling of pits. (1.1.1) In all types of soils.

Extra for every additional lift of 1.5 m or part thereof. (1.6.1) All types of soils

Filling from available excavated stuff (Excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering with a lead upto 50 M. and lift upto 1.5 M.

Providing and filling in plinth with sand/ Crusher dust and hard moorum under floor in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, including dressing etc. complete.

Providing and fixing form work including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: (2.1.1) Foundations, footings, bases of columns plinth beam, curtain wall in any shape and size and all type of wall below plinth level.

Columns, Pillars, Piers and likes- rectangular or square in shape

Columns, beams & walls- circular or any other geometrical shape other than square and rectangular in all sizes

Beams, lintels, cantilevers & walls

Suspended floors, roofs, access platform, balconies (plain surfaces) and shelves (cast in situ)

Weather shade, chhajja, Cornices and mouldings

Stair cases of all types excluding spiral and folded plate type, including risers and landings

Extra for additional height every 1m or part thereof where height of staging for form work exceeds 4.0 metre with adequate bracing, propping etc at all levels, for suspended floor, roof, landing, beam and balcony. (only plan area is to be measured):

Providing and laying nominal mix plain cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work. (3.1.3) 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size).

1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size).

Providing and laying nominal mix reinforced cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work. (Note :Excess/ less cement used as per design mix is payable/ recoverable separately) (3.2.1) 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size).

Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire in foundation and plinth all complete: (3.12.2) Thermo-Mechanically treated bars FE 500

Providing and laying damp proof course (upto 50mm thick) with plain cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20mm nominal size) including form work.

Making 50mm thick plinth protection of plain cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with sand including finishing the top smooth.

Grading roof for water proofing treatment with: (4.13.1) Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in foundation and plinth in: (7.5.4) Cement Mortar 1:6 (1 cement : 6 coarse sand)

Extra for brick work in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

Extra for brick work in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

In Super Structure (G.f.)

Extra for providing and placing in position hopping 25x1.60 mm or 2 Nos 6mm dia MS bars reinforcement at every third course of half brick masonry. (382 + 11 +62.50 = 455.50)

Providing and laying AAC Autoclaved aerated concrete block confirming to IS: 2185 (Part-3)-1984) in block masonry with AAC blocks of width 100/ 200mm height 200/250/300mm, length 400/500/600 mm (approved sizes) with cement mortar 1 :6 (1 Cement :6 coarse sand) in superstructure. AAC blocks should have specific gravity 0.6 to 0.65 and crushing strength should not be less than 3 N/ sqmm (testing as per IS: 6441 - 1972).

Moulding and cornices with brick masonry using bricks of crushing strength not less than 35 kg/sqcm and water absorption not more than 20% in cement Mortar 1:4 (1 cement 4 coarse sand) including cement plaster 15 mm thick, 10 cm projected, 20 cm deep (40 cm Girth) in cement mortar 1:4 (1 cement : 4 fine sand) at any floor.

Providing and fixing Dash fastener (for fixing door/ window frames) on C.C. / R.C.C./ Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. (8.4.3) Dash fastener 12x100mm

Providing and fixing PVC membrane foil coated (laminated) flush door shutters, made with core of block board with frame of first class hard wood, coated with 0.30mm membrane pasted with resin using vacuam treatment process complete all but excluding hinges. (8.16.1) 35 mm thick (single leaf)

Extra for double leaf shutter instead of single leaf.

Providing and fixing antique/ SS finished brass parliamentary hinges with antique/ SS polished MS screw complete: (8.78.1) 150x125x27x5 mm

Providing and fixing antique/ SS finished brass sliding door bolt with necessary bolts, nuts and antique/ SS polished MS screw complete: (8.79.1) 300x16mm

Providing and fixing antique/ SS finished brass door latch with antique/ SS polished MS screw complete: (8.80.1) 300 x16x5 mm

Providing and fixing antique/ SS finished brass tower bolts (Barrel type) with antique/ SS polished MS screw complete: (8.81.1) 250 x10 mm

Providing and fixing 100mm antique/ SS finished brass mortise latch and lock with six levers and a pair of lever handles with antique/ SS polished MS screw complete.

Providing and fixing hanging powder coated aluminium door stopper with necessary M.S. screws etc complete. (8.130.1) Single

Providing and fixing IS: 3564 marked aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc complete.

Providing and fixing 30mm thick fibreglass reinforced plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF) / Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856 : 2000, complete.

Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of red oxide zinc chromate primer. (9.6.2) In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and fixing clear float toughened glass door or partition in required thickness frameless in appropriated sizes inclusive of edge molding polish and making required size slot or hole for patch fitting/hardware etc. The glass to be assembled together with patch fitting and hardware in proper alignment with all labour tools and tackles etc complete. (Patch fittings and hardware to be paid for separately). 12 mm thick for door/partition

Providing and fixing of stainless steel grade 316 patch fitting and hardware of approved (Hardwyn, Ozone, Godrej) make in frame less toughened glass door or partition in proper alignment with all tools tackles and labour etc complete. 1. Top patch with pivot SS grade 304

2. Top/side patch glass or L-connector patch SS grade-304

3. Bottom patch to be connected with floor machine

4. Bottom lock patch with three key SS grade 304

5. Corner patch fitting with pivot SS grade 304

6. Two way action Hydraulic floor spring machine heavy duty double cylinder type Capacity 120/150 kg mounted on floor including required cutting on floor and proper grouting with rich cement mortar.

7. H type handle 32x600mm SS 304 grade

8. Floor/Wall to Glass Connector SS grade 304

Steel work in tubular (round, square or rectangular hollow tubes etc.) structure in built-up sections, trusses and frame work including cutting, hoisting, fixing in position upto a height of 5m above plinth level, consisting of columns trusses, roof and bottom purlins, base plate, holding down bolts, wind ties bracing (if required), bolts, nuts and washers for fastening etc. complete with applying a priming coat of red oxide zinc chromate primer. (9.3.2) Electric resistance or induction butt welded tubes Grade-300

Extra for hoisting trusses and placing in position over height above 5m for every 2.5 m height or part thereof.

Providing and fixing M.S. grill of approved pattern made of M.S. flats or square or round bars welded to steel frame of windows etc. including applying a priming coat welded to frame with all necessary fitting complete including applying a priming of red oxide zinc chromate primer.

Providing and fixing aluminium work for doors, windows, ventilators and partitions made out of extruded aluminium standard sections (main section with minimum 1.5mm thickness) conforming to IS: 733, IS: 1285 mitred and jointed mechanically including aluminium cleats, neoprene weather stripping gasket beveled edge beading, screws duly fixed in wall/ floor with fixing clips or hold fasteners or bolts and nuts as required aluminium sections shall be anodized transparent or dyed to approved shade according to IS: 1868, minimum anodic coating shall be of grade AC-15. (Glazing to be paid for separately: (9.47.1) For fixed portion

For shutter of doors, windows & ventilators including providing and making provision for fixing of fitting wherever required including the cost of PVC/ neoprene gasket required (Fittings shall be paid for separately).

Extra for powder coated (minimum 50 micron) aluminium sections instead of anodized.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete. (Cost of aluminium snap beading shall be paid in basic item): (9.51.2) With float glass panes of 5 mm thickness

Extra for providing and fixing reflective glass panes in aluminium door, window, ventilator shutters and partitions instead of float glass. (9.59.2) 5 mm thickness

Providing stainless steel railing/ grill made of S.S. flats, hollow S.S. pipe or square/ rectangular sections of approved design fixing in stair case, balcony or other places with metal fasteners and stainless steel bolts etc complete. (9.57.2) SS Grade 304

Extra for providing and fixing wind ties of 40x6mm flat iron section.

Supply and fixing of polymer precoated galvalume profile sheets (PPGL) of approved size, shape and pitch of corrugation, total coated thickness (TCT) 0.60 mm +/- 5%, epoxy primer on both side of the sheet and colour polyester top coat 18-20 microns and 6-7 microns on bottom. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Extra for working height above 6 metre for fixing GI/ profile/ PVC/ polycarbonate sheet for every additional height of 1 metre of part thereof. 5 m. above 6 m.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm +/- 5% total coated thickness (TCT), Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers complete : (10.16.6) Gutter. (600 mm over all girth).

Providing and fixing 18mm thick insulating board ceiling of approved quality with necessary nails etc., complete (Frame work to be paid separately). (10.31.3) Flame retardant face insulating board

Providing and fixing at all height false ceiling consisting of frame work "W" / "U" / "L" sections made of G.I. sheet with zinc coating of grade 120 consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick button wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.55mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed including providing and fixing 12.5 mm thick tapered edge gypsum board conforming to IS: 2095- Part-I all complete as per drawing and specification and direction of the Engineer in Charge but excluding the cost of painting.

Providing and fixing Acoustical Suspended Ceiling System made of tiles of size 595x595mm and specified thickness as approved by Engineer-In-Charge, in tru Horizontal Level Suspended on interlocking metal grid of hot dipped galvanised steel sections (galvanised @120 gsm both side inclusive) consisting of main "T" Runner with suitably spaced joints to get required lenght and of size 24x38 mm made from 0.30 thick(minimum ) sheet, spaced at 1200mm center to center and cross "T" of size 24x38mm made of 0.30 thick (minimum) sheet, 1200 mm long spaced between main "T" at 600mm center to lenght 600 mm and size 24x38mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24mm and laying false ceiling tiles of approved texture in the grid, cutting/ making opening for services like diffusers, grills light fitting, fixtures, smoke detectors etc wherever required. Main "T" runner to be suspended from ceiling using GI slotted cleats of size 27x37x25x1.6 mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm dia GI adjustable rods with galvanised butterfly level clips of size 85x30x0.8 mm spaced at 1200mm center ot center along main "T". Bottom exposed width of 24mm of all "T" sections shall be pre-painted with polyster paint, all complete for all heights as per specification drawings or as directed by Enginner-In-Charge. The tiles should have Humidity resistance (RH) of 99%, Light Reflectance>83%, Thermal Conductivity K=0.052-0.57 w/mk, color white, fire performance UKclass0/Class1(BS476pt-6and7) in module size of 600x600x16 mm with Bio Block coating on the face of the tile, suitable for green building application, with recycled content of 38-41%. Cielinng height up 3.5 mt from adjacent floor level. Extra height to be paid serately. (10.67.2) With 20 mm thick bevelled/tegular edged mineral fibre false ceiling tile (NRC 0.7)

Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595 mm, having NRC(Noise Reuction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85%(minimum). Non combustible as per BS:476(part-4), fire performance as per BS:476(part 6&7), humidity resistance of 100%, thermal conductivity 0.048 to 0.050 W/m0 KC as per ASTM 518:1991, Weight 1.900 Kg to 2.100 Kg per tile, 15 MM Edge Density Having 450 Kg/cum & 10 MM Central portion of tile having 350 Kg/cum, comprising of a frame made from especially fabricated galvanised mild steel steel sheet 0.50 mm thick pressed section (galvanizing @ 120 grams per sqm incluidng both sides) i.e. vertical studs of size 48 x 34 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50x32 m fixed to the floor and soffit at 600 mm centers using 12mm dia, 40mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 500mm wide (90 metre) roll and two coats of primer suitable for panelling as per manufacturer's specifiaction as per direction of Engineer-In-Charge all complete.

Providing and making 6mm thick cement plaster of mix: (11.1.2) In Cement mortar 1:4 (1 cement : 4 fine sand)

(11.1.1) In Cement mortar 1:3 (1 cement : 3 fine sand)

Providing and making 12mm thick cement plaster of mix: (11.2.4) In Cement Mortar 1:6 (1 cement : 6 fine sand)

Providing and making 15mm thick cement plaster on the rough side of single or half brick wall of mix: (11.3.4) In Cement Mortar 1:6 (1 cement : 6 fine sand)

Providing and making 18mm thick cement plaster in two coats with under layer of 12mm thick plaster 1:5 (1 cement : 5 fine sand) and top layer of 6mm thick with cement plaster 1:3 (1 cement : 3 fine sand) finished rough with sponge.

Neat Cement punning.

Extra for providing and mixing water proofing materials in cement plaster work in proportion as recommended by manufacturer.

25mm thick cement concrete flooring with 1:2:4 cement concrete (1cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) finished with floating cost of neat cement.

15 mm thick Table rubbed polished Granite stone slab in risers and treads of steps skirting dado and pillars laid on 12mm (Average) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry including rubbing and polishing etc. complete (single stone is to be used for risers and treads of steps and width of stone for skirting and dado shall be equal to the height of skirting & dado and length of 1.0 m). (12.46.2) Granite stone black

Extra for nosing in Granite stone for treads.

Providing and fixing recified glazed ceramic wall/dado tiles of 1st quality conforming to IS:15622-2017 of approved make, in all colors, shades on wall and dados over 12 mm thick bed of cement Mortar 1:3(1 cement:3 coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with matching pigment complete. (12.75.1) Size 300x450mm thickness 7 to 8mm

Providing and laying ceramic glazed floor tiles conforming to IS : 15622 of approved size, make, colour, shade laid on 20 mm thick Cement Mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement mixed with matching pigment etc., complete. (12.9.1) Size above 300x300mm

38 mm thick parquet (wood blocks) flooring of teak wood laid over 25mm thick leveling layer of cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm nominal size) to be paid separately coated with thin layer of hot bitumen (blown type) @ 2.45 kg/ sqm including fixing blocks after dipping in hot bitumen (blown type) upto half depth planned, leveled, smooth and finished complete

Extra for plaining the lower surface of wooden planking

Providing and laying DOUBLE/MULTI CHARGE (minimum 2.0mm thick layer) VITRIFIED floor tiles with water absorption less than 0.05% and conforming to IS:15622-2017 of approved make in all colours and shades and size mentioned below (+/- 10 mm), laid on 20mm thick cement mortar 1:4(1 cement:4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete. (12.79.1) Size 600x600mm thickness 9 to 10mm

Providing and laying DOUBLE/MULTI CHARGE (minimum 2.0mm thick layer) VITRIFIED floor tiles with water absorption less than 0.05% and conforming to IS:15622-2017 of approved make in all colours and shades and size mentioned below (+/- 10 mm), laid on 20mm thick cement mortar 1:4(1 cement:4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete. (12.79.2) Size 800x800mm thickness 9 to 10mm

15mm thick Granite work (machine cut, table rubbed & mirror polished) for kitchen platform, vanity counters, window sills and similar locations of required size laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) including joints treated with white cement mixed with matching pigment including rubbing and polishing to edge moulding to give high gloss finish. (13.6.2) Granite stone black

Wall painting with acrylic luxury emulsion (plastic) paint of required shade to give an even shade. (14.11.1) On new work (two or more coats)

Providing and applying 2mm thick ready mix exterior grade approved make putty (like Birla wall care, Alltek Superfine W/R of (NCL), Asian, ICI, Nerolac, J.K. wall putty) on walls to make the surface smooth and even.

Painting exterior surface with ACRYLIC SMOOTH exterior paint of required shade as per manufacturer's specifications to give protective and decorative finish including cleaning washing of surface etc. complete with: (14.15.1) On new work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Painting exterior surface with PREMIUM ACRYLIC SMOOTH exterior paint of required shade as per manufacturer's specifications to give protective and decorative finish including cleaning washing of surface etc. complete with: (14.16.1) On new work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Painting on new work (two or more coats) to give an even shade with: (14.22.1) Satin synthetic enamel paint

Providing and fixing corrugated fibre glass sheet roofing in any shade/ colour fixed with G.I. ‘J’ hooks, bolts, nuts and washers etc. complete but excluding cost of purlins, rafters, trusses etc. with: (10.25.2) 2.00mm thick fibre glass sheet

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required : (17.10.1.3) Kitchen sink with drain board 510x1040 mm, bowl depth 200mm.

Semi rigid pipe (17.28.1.2) 40 mm dia.

Providing and fixing vitreous china water closet (European type W.C. pan) with white ISI marked plastic seat and lid, 10 litre low level white P.V.C. flushing cistern (same colour), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : (18.4.3) White wall hung type

Providing and fixing vitreous china wash basin with C.I. brackets, 32 mm C.P. brass waste of standard pattern, including painting of brackets, cutting and making good the walls wherever required : (18.17.2) White Size 550x400 mm

Basin mixer pillar tap with spout (1000 grams)

Providing and fixing white vitreous china urinal basin with waste fitting as per IS : 2556, and other couplings in C.P. brass complete: (18.13.2) Flat back type urinal of size 460x380x250mm

Providing and fixing 15 mm nominal bore C.P copper connection pipe with C.P brass nuts collar and PVC bush of approved quality: (18.11.1) 30 CM length

providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: (19.14.1) Bib cock (400 grams)

Two way bib cock (800 grams)

Kitchen sink mixer with cast swivel spout (1000 grams)

Toilet paper holder

Health foscet (hand jet) with flexible connection pipe (for WC)

Providing and fixing stainless steel drain jali of approved make/quality

Toilet paper holder

Soap dish plate

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1mx1mx650 micron thick (0.65mm), finished with 12mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement rounding the edge sand making and finishing the outlet complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 150mm diameter and weighing not less than 440 grams.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (19.5.2) 20 mm nominal outer dia .Pipes.

25 mm nominal outer dia .Pipes.

32 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (19.4.2) 20 mm nominal outer dia .Pipes.

25 mm nominal outer dia .Pipes.

32 mm nominal outer dia .Pipes.

40 mm nominal outer dia .Pipes.

50 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete (19.6.4) 32 mm nominal dia .Pipes.

40 mm nominal dia .Pipes.

50 mm nominal dia .Pipes.

62.50 mm nominal dia .Pipes.

15 mm nominal dia .Pipes.

25 mm nominal dia .Pipes.

Constructing masonry Chamber 30x30x50 cm, inside with modular well burnt clay bricks of 35 kg/ cm² in cement mortar 1:4 (1 cement : 4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded

Constructing masonry Chamber 60x60x75 cm, inside with modular well burnt clay bricks of 35 kg/ cm² in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm. top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design :

Supply, erection, jointing, testing & commissioning of "C" Class MS pipes (as per IS: 1239) including necessary specials such as tees, bends, flanges reducers etc., complete on wall/ ceiling. The pipes to be erected on wall or suspended from beams, RCC roof slabs with suitable size MS bars/ angle irons including painting of metal part except pipe line. (23.1.1) 50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

Providing ISI Mark 32 mm dia G.I. ( B class) riser pipe and M.S. plunger rod in 3 meter length socketed on one end as per IS: 1239 ( Part I) 1990 with up to date amendments and socket as per IS: 2062/1990 up to date amendments.

Supplying and fixing single headed internal hydrant valve with instantaneous Gun metal couplings of 63 mm dia with cast iron wheel ISI marked conforming to IS: 5290 (Type - A) with blank Gunmetal cap and chain as required.

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : (23.5.1) 80 mm dia

100 mm dia

150 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required : (23.4.2) 100 mm dia

150 mm dia

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

Supplying and fixing swinging type First-Aid Hose Reel drum with MS construction spray painted in Post office Red colour, conforming to IS: 884 with upto date amendments, complete with brackets for fixing on wall, connections from riser with 25 mm dia MS/GI pipe and GM gate valve but excluding hose reel.

Supplying and fixing 2 way Fire Brigade Connection of cast iron body with 2 Each. Gun metal male instantaneous inlet couplings complete with cap and chain conforming to IS: 904 including connection to existing MS pipe line complete as required.

Supplying and installing Air Vessel of 300 mm dia, 1.5m in height made of 5mm thick MS sheet including painting with one primer and two finish coats complete as per specification.

Providing and fixing pressure switch with suitable for 1-10 Kg/cm2 including 12/15 mm Ø isolation valve, G.I. nipple, elbow, electrical connections setting of Cut-In and cut-Off pressure complete in all respects and in an approved manner.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying nominal mix plain cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work. (3.1.1) 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size).

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: (20.3.3) 180x150 mm size P type

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : (20.7.1) Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions,total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

Extra for depth for manholes : (20.8.1) Size 90x80 cm

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : (23.5.1) 80 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required : (23.4.1) 80 mm dia

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality. (20.15.1) HD-20 circular shape 560 mm internal diameter.

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer –in-charge, upto 90 metre depth below ground level. (21.1.1) All types of soil (21.1.1.3) 150 mm dia.

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer –in-charge. (21.3.4) 200 mm nominal size dia.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. (21.4.4) 200 mm nominal size dia.

Supplying, filling, spreading & levelling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. (21.14.1) Stone boulders of size range 5 cm to 20 cm, in recharge pit

Gravels of size range 5 mm to 10 mm, over the existing layer of boulders

Coarse sand of size range 1.5 mm to 2 mm over existing layer of gravel

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, including disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: (21.11.4) 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. (21.12.4) 200 mm dia

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing and fixing 15 mm nominal bore uplasticised PVC connection pipe with PTMT nuts and PVC bush of approved quality and colour: (18.10.2) 45 CM length

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: (19.14.7) Angle valve for basin mixer and geyser points (450 grams)

Providing and fixing powder coated M.S. hooks and eyes necessary iron screws: 300 mm

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: (19.14.19) Health foscet (hand jet) with flexible connection pipe (for WC)

Towel rail (600mm long x 20mm dia)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: (19.14.10) Wall mixer with elegant knob (1400 grams)

Providing and fixing on wall face or under floor UV stabilized Unplasticised Rigid PVC pipes (single socketed) having 3.2mm wall thickness conforming to IS : 13592 (4kg/sqcm) including required couplers, jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc complete. (18.76.1) 75 mm dia pipe.

110 mm dia pipe.

150 mm dia pipe.

Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (18.77.5) "P" trap 110mmx110mm long

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed and socketed/ plain ended casing pipes of required dia, conforming to IS: 4270, of reputed & approved make, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge. (21.7.1) 100 OD Pipe

Providing, laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : (20.1.2) 150 mm diameter

200 mm diameter

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. : (18.33.2) For 75 mm OD Pipe

For 110 mm OD Pipe

Plain reducing Tee 110x75mm

Providing and fixing cast iron grating for gully trap. (18.27.1) 100x100mm square or round

Multi floor trap 110

Providing, lowering, laying, aligning, fixing in position at and jointing at all level/ depths ISI marked HDPE pipes of PE-100 grade and PN 6 for sewer application as per IS 14333-1996 (amended upto date) in trenches in complete including all material, labour, testing and commissioning as per direction of Engineer. (20.6.1) 100 mm dia

150 mm dia

200 mm dia

Providing and fixing stainless steel drain jali of approved make/quality.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (19.4.5) 40 mm nominal outer dia .Pipes.

50 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete (19.6.1) 15 mm nominal outer dia pipes

20 mm nominal outer dia pipes

25 mm nominal outer dia pipes

32 mm nominal outer dia pipes

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : (19.17.1) 15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

Providing and fixing gunmetal single acting air release valve with screwed inlet 25 mm dia and with necessary G.I. coupling, valve to be fitted on top of Air vessel or on wet riser as per specification.

Supplying, fixing, testing and commissioning of following size Motorised BUTTERFLY VALVE with C I body SS Disc, O- Ring and minimum PN 16 pressure rating, conforming to BS 5155, IS 13095, with IP-55 actuator, capable of accepting upto 10V DC, and upto 20 mA electric signal and providing similar transduced feedback output to control system as per specification. (25.26.2.10) 150mm dia.

125mm dia.

100mm dia.

Supplying and fixing swinging type First-Aid Hose Reel drum with MS construction spray painted in Post office Red colour, conforming to IS: 884 with upto date amendments, complete with brackets for fixing on wall, connections from riser with 25 mm dia MS/GI pipe and GM gate valve but excluding hose reel

Supplying and installing pressure gauge of 100 mm Ø., 0-300 PSI or 0-21 kg per cm square fitted with 12/15 mm Ø. pad cock valve, and G.I. pipe, elbow etc. as per requirement in approved manner.

Supplying of following sizes GM gate valve as per specification. (32.105.5) 40 mm dia.

32 mm dia.

25 mm dia.

Providing, lowering, laying, aligning, fixing in position at and jointing at all level/ depths ISI marked HDPE pipes of PE-100 grade and PN 6 for sewer application as per IS 14333-1996 (amended upto date) in trenches in complete including all material, labour, testing and commissioning as per direction of Engineer. (20.6.1) 100 mm dia

150 mm dia

200 mm dia

100 mm dia. R.C.C. pipe

150 mm dia. R.C.C. pipe

Providing, lowering, laying, aligning, fixing in position at and jointing at all level/ depths ISI marked HDPE pipes of PE-100 grade and PN 6 for sewer application as per IS 14333-1996 (amended upto date) in trenches in complete including all material, labour, testing and commissioning as per direction of Engineer. (20.6.1) 100 mm dia

150 mm dia

200 mm dia

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete (20.5.1) 100 mm dia. R.C.C. pipe

150 mm dia. R.C.C. pipe

Providing filling and compacting local earth (from approved source pit) in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, including dressing etc. complete.

Cement art Mural work For Moulding Design Work

Providing & laying 60mm thick precast interlocking concrete blocks of approved size (approx 305 sqcm) and shape/ pattern, over 40 mm thick average complete coarse sand bed with joints of 3mm thick filled by fine sand including leveling with surface vibrator, temping and sweeping etc. complete of minimum compressive strength of 250 kg/sq.cm (12.65.2) Pigment Coloured (rubber mould) precast interlock concrete blocks

Providing and fixing precast compressed plain cement concrete edge restraint of size 500mm x 250mm x 60mm of compressive strength of 200kg. per sq.cm manufactured by electro hydraulically operated block machine by excavated trench of 150mm depth etc. complete

Supplying and stacking of good earth at site including royalty, loading, unloading and carriage upto 10 km (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking sludge at site including royalty, loading, unloading and carriage upto 10 km (sludge measured in stacks will be reduced by 8% for payment).

Rough dressing the trenched ground including breaking clods.

Spreading of sludge, dump manure or/and good earth in required thickness (Cost of sludge, dump manure or / and good earth to be paid separately).

Mixing earth and sludge or manure in proportion specified or directed.

Preparation of beds for hedging and shrubbery by excavating 60cm deep and trenching the excavated base to a further depth of 30cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, levelling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as directed, within a lead of 50m lift upto 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately).

Providing and planting following herbs in garden including preparation of soil, base plantation, providing and spreading different fertilizers, soil and sand: (22.25.4) Carpet grass well developed

Hedges like Alife, Dorenta, Tikoma etc

Furn like Arica, China etc (3 year old)

Hibiscus (Flower)/ Rose

Providing wood work in frames of doors, windows, clerestory windows and other frames wrought framed and fixed in position. (8.1.2) Sal, bijasal, benteak, khair, haldu

Providing 40x5mm iron hold fast 40cm long including fixing to frame with 10mm bolts nuts and wooden plug and embedding in Cement Concrete 1:2:4 in blocks of size 30x10x15cm.

Providing and fixing bright finished brass butt hinges with brass polished MS screws complete: (8.58.1) 125x85x5.50 mm (Heavy Type)

Providing and fixing bright finished brass sliding door bolt with nuts and brass polished MS screws complete: (8.60.2) 250x16mm

Providing and fixing brass door latch with brass polished MS screws complete: (8.61.2) 250x16x5 mm

Providing and fixing bright finished brass tower bolts (barrel type) with brass polished MS screws complete: (8.62.2) 200x10mm

Providing and fixing bright finished brass door handles with brass polished MS screws complete: (8.65.1) 125 mm

Providing and fixing ceramic glazed wall tiles conforming to IS : 15622 of approved make, colours, shades and size on wall and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with matching pigment complete. (12.7.1) Size 200x300mm

Providing and laying vitrified floor tiles with double charge/ multi charge printing with water absorption less than 0.5% and conforming to IS : 15622 of approved make in all colours and shades and size mentioned below (+/- 10mm), laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete. (12.13.1) Size 600x600mm

Carriage by mechanical transport upto 5 km lead: (1.26.1) Earth

Boring/drilling bore well perfectly vertical for the specified depth suitable to receive required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer–in-charge upto 90 metre depth below ground level. (21.1.1) All types of soil (21.1.1.2) 125 mm dia.

Rocky strata including Boulders. (21.1.1.2) 125 mm dia.

Boring/drilling bore well perfectly vertical for the specified depth suitable to receive required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer–in-charge beyond 90 metre & upto 150 metre depth below ground level. (21.2.2) Rocky strata including Boulders. (21.2.2.2) 125 mm dia.

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer –in-charge. (21.3.2) 125 mm nominal size dia. (50 mtr.)

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for bore well of: (21.11.2) 125 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tube well as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. (21.12.2) 125 mm clamp.

Providing and laying in trenches G.I. pipes medium class complete with G.I. fittings including excavation of trenches, refilling the same and testing of joints complete: (19.9.5) 40 mm dia. nominal bore

KOTA stone slab 25mm thick in risers and treads of steps, skirting dado and pillar laid in 12mm (Average) thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. (single stone is to be used for riser and treads of steps and the width of stone for skirting and dado shall be equal to the height of skirting/ dado up to length of 1.0 M.)

Providing and fixing brass/gun metal gate value with C.I. wheel of approved quality (screwed end) 50 mm nominal bore

Providing and fixing 15 mm dia, Quartzoid bulb type G.M. Sprinkler Head set to operate at 680C of approved make chrome plated complete in all respect as required.

MAIN HALL FLOORING: Providing & fixing of Loop pile Carpet,100% BCF polypropylene, solution dyed having pile height of 6mm having total density not less than 1100 gsm carpet in hall & balcony areas. Primary & secondary backing of Woven Polypropelene & having permanent static control with proper underlay of hitlon sheets of 10mm & total thickness between16mm rubber solution / SR- 998 pasted on the floor with suitable adhesives including labour etc complete.

PROVIDING AND FIXING/PLACING IN POSITION AUDITORIUM CHAIRS WITHOUT DESKLET:- Seat Shall be made of Polyurethane Foam Moulded with 1.5+0.1cm thick plywood insert and upholstered with fabric. Approx Seat Size: Depth 42.0cm x Width @ rear 44.0cm x Width @front 41.0cm. The Back assembly shall be flexible type and made of polyurethene Foam moulded with M.S. tubular frame insert and upholstered with fabric and back cover. The insert is made of ᴓ1.9+0.02cm x ᴓ0.16+0.128cm. M.S. thick Tubular Frame with flexible nylon straps running across the length and width of the frame. Approx Back Size: Height 65.5cm x Width @ top 34.5cm x Width @ seat level 46.0cm. High Resilience Polyurethane foam is moulded with density 45+2 kg/cu.m. The back cover and mechanism cover shall be vacuum formed from black ABS Sheets. Armrest understructure shall be upholstered with PU foam Moulded with MS insert. Arm tops shall be made of black integral skin polyurethane with 50-70 Shore A harness & reinforced with wooden insert. Armrest width 7.0+0.5cm and shall be offered as common/individual armrest between chairs. Chair Understructure shall be made of MS powder coated (DFT 40-60 microns) with integrated auto tip up mechanism which folds the seat when not in use. Base plat shall be made of HR steel with base area of 15.0+02cm. x 22.0+0.2cm x 0.5+0.05cm thick. Backrest supporting beam width: 46.0 + 0.2cm (L) x 8.0+0.03cm x 4.0+0.03cm x 0.2+0.0016cm MS tube. Understructre fixed to ground with mechenical/Chemical Bolting.(Location: Main Auditorium, 100 Seater Auditorium, 54 Seater Auditorium.) Refer Drawing No. TD-20.

2 SEATER SOFA-WAITING Dimension: 1538L x 820 x650 H , Arm Height 210mm, Back Height from Armrest: 250mm, Arm Width : 135mm, . Type of Thread Used: Polyster, 6stiches per inch. (PU/PVC/Cotton/ Polyester/ Composite): Thickness : 1mm, Weight 575GSM. FRAME MATERIAL ( PINE WOOD ): Moisture content less then 10%, Anti – Tremite Treatment (Borex Powder Treatment). Thickness of Plywood used(mm) :12mm & 18mm. Standard : IS 303 Commercial Plywood used. SEAT FOAM: Thickness (mm) : 103 mm + 22 mm, Density (Kg/m3): 32 density/28 density soft. Type of foam: Slabstock foam. Back Foam: Mixing of PSF & cut piece of foam. ARMREST FOAM: (DENSITY, TYPE): Thickness (mm) : 24 mm, Density (Kg/m3): 40 density. BELT/ WEBBING MATERIAL:: Width of belt (mm) :68mm - 48mm, Total length of belt used (mm): 68mm :- 3500 mm ; 48mm :- 1850mm. Fixing of Leg : (Self Tapping Screw / Insert with metric threading) :- Woodscrew provided on frame in addition to M-8 / T-Nut. * Material of leg : (Plastic / Insert Moulding / Wooden/ MS / SS) :- leg 95 mm. (Location: Reception.) Refer Drawing No.TD-24.

ACCOUSTICAL DOOR Providing and fixing Acoustical Sandwiched Doors of size from First class teakwood frame of finished size 225mm x 80 mm and 66mm thick finished shutters consisting of 100x42mm teakwood style, top and lock rail 125x42 and bottom rail, 150x42mm, and intermediate 25mmx42mm Teak wood horizontal members,with 8mm thick BWP 710 grade ply on both sides and 4mm thick natural veneer (BWP grade) with grooves on one side (Green ply Century make or equivalent). 50mm thick core of Glass wool slab (24 kg density)16g Fiber glass tissue paper sandwitched inside and 25mm thick 32 density kurlon make foam with 1 mm thick leatherite, stitched in rombus shape on inside. Heavy duty stainless steel hinges (152mmx76mmx3mm) 316 grade with bearings with Pin and cap, 300mm tower bolts ss 304 grade, 450mm heavy handle ss 316 grade, 350mm heavy duty Aldrops ss 316 grade, heavy door stoppers (zinc), rubber buffers, concealed hydraulic door closer aluminum extruded wt. up to 90 kgs, (Ozone or Yale make) as per drawing schedule of fitting and fixtures of (kich, Godrej make or equivalent). All around edge Teak wood bead 70mm x 12mm thick, including finishing the over all surface with thinner polish spray and P.U. coating etc, complete to the satisfaction of Engineer in Charge.

STAGE CURTAIN Manufacture, providing and commissioning of front main curtain and control mechanism as per following materials of size 17.00 mt x 7.00 mt .1)The main curtain fabric should be more than 300 gsm and more than 25000 to 30000 Rub count 100% polyster in width of 1.40 mts. fabric should stitched with 100 to 120 mm frill all width of fabric to stitch with each other in half width of opening and properly attached with the track assembly.2)Providing and commisioning to track channel of special section 32x22x1.5 mm buffed polised anodized or powder coated track around with heavy duty drive belt geared in 12 to 10mm wide attached with pully drive and master slider and with track is fixed S.S. bracket to hold the track at top of curtain (track length is 7.8mts).3)The above curtain is to controlled by special electronic type motor imported make of Selve (Germany) of equivalent make of torque rated load 2.00 Nm of 80 watt power for carrying the load of fabric up to 80 kg operated with tough drive in radio automotive motor 2 Nos. for operating the curtain two opposite direction. One no. backup motor also to be paired with this system. The motor is to be controlled by R.T.S. Remote control and backups with wireless transmission switchs. (Total operation to be done as per drawing design and direction of Engineer-in-charge)

Providing and planting of 3‟0” to 4‟0” heighted wasingtonia, filipheria/bismarkia novelist plam plants with 1‟6” x 1‟6” depth pit formation and soil preparation, (Mixing organic manure and plant‟s protection insecticide). Up to 4 month maintenance.

Providing and planting of 4‟0” to 5‟0” heighted Ficus prestige/Blackiana plants with 1‟6” x 1‟6” depth pit formation and soil preparation, (Mixing organic manure and plant‟s protection insecticide). Up to 4 month maintenance.

Wiring for light/ fan/ exhaust fan / call bell point with 3x1.5 sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.I. box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Short Point

Medium Point

Long Point

Wiring for twin control light point with 3x1.5 sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.I. box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)

Extra for providing and fixing light plug point on board in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) point wiring with modular type 3 pin 5/6 amp socket outlet and 5/6 amp switch including cost of base and cover plate and G. I. box etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)

Wiring for light plug point with 3x2.5 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 6 Amp switch and 3 pin 6 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Extra Long Point I

Extra Long Point II

Extra Long Point III

Wiring for power plug point with 3x4 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 16 Amp switch and 6 pin 16 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Extra Long Point I

Extra Long Point II

Extra Long Point III

Wiring for power plug point with 3x6 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 32 Amp SPMCB "C" curve and 6 pin 20 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Extra Long Point I

Extra Long Point II

Extra Long Point III

Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, wire in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) 3 X 1.5 sq. mm in 20mm conduit

3 X 2.5 sq. mm in 20mm conduit

6 X 2.5 sq. mm in 25mm conduit

3 X 4 sq. mm in 25mm conduit

3 X 6 sq. mm in 25mm conduit

3 X 10 sq. mm in 25mm conduit

3 X 16 sq. mm in 32mm conduit

2 X 25 sq. mm + 1 X 16 sq. mm in 32mm conduit

Supplying and fixing of following sizes FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with accessories in concealed complete as per specification and IS: 9537 (2000 Part 5) 25 mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, multi strand wire in the existing surface/ concealed, FRLS PVC conduit / PVC casing caping as per specification and IS: 694 (2010) 1 x 2.5 sq. mm

1 x 4 sq. mm

Supplying and drawing UTP 4 pair Cat 6 LAN wire in existing surface/ concealed Steel/FRLS PVC conduit as per specification

Supplying and fixing following modular switch, socket, other accessories on the existing modular plate & switch box including connections but excluding modular plate etc. as per specification. Fan regulator (two module size) electronic stepped type moving all rounds

Ceiling rose 3 pin 5 amp

Batten/ angle holder

Blanking plate

Providing and fixing composite unit for computer points having modular type 1 No 6 pin 16 amp socket outlet, 1 No 16 amp switch, 3 Nos 3 pin 6 amp socket outlets, 3 Nos 6 amp switches, suitable G.I. box, base and cover plates, earthing the sockets and switch box including etc. as per specification.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts A.C. supply, complete as per specification. Deluxe

Providing and fixing fan hook made of 12mm dia steel bar in existing ceiling slab including cutting of roof, fixing hook above reinforcement on both side, repairing with cement mortar 1:2 (1 cement : 2 sand) etc. as per specification.

Supplying, installation, testing and commissioning of following sizes ceiling fan including wiring the down rods of standard length up to 30 cm with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, earthing etc. complete as required. P.F. should be greater than 0.9, with BEE Star rating from 3 star and above, IS: 374:2019 including all amendments. 1200 mm sweep

Supplying, installation, testing and commissioning of following sizes Pedestal fan with telescopic arrangement for height adjustment and standard wiring/connection etc complete as per specification. P.F. should be greater than 0.9 450 mm sweep

Supplying and fixing of wall/ cabin fan including connection etc. as per specification. P.F. should be greater than 0.9 400 mm sweep

Supplying, installation, testing and commissioning of following sizes heavy duty (continuous running) 1400 rpm exhaust fan in existing opening in wall including earthing etc. complete as per specification. P.F. should be greater than 0.9 300 mm sweep

Supplying and fixing following sizes of down rod of 15/20mm dia M.S. pipe of thickness 2 mm to ceiling fan including painting with matching colour etc. as per specification. 60 cm long

Providing and fixing phenolic laminated sheet cover of 180 mm dia 3 mm thick on the fan box etc. as per specification. (If provided at the time of installation of ceiling fan)

Supplying, installation, testing and commissioning of following LED fitting (luminaries) Panel Light in round/ square shape complete with electronic driver heat sink capacitor and all other accessories on surface/ in false ceiling etc. as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 18/20 Watt

Supplying, fixing, testing and commissioning of following LED lamps with inbuilt electronic driver heat sink and all other accessories in existing holder/ luminaries as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 15 Watt

Supplying, installation, testing and commissioning of following COB LED Spot Light fitting complete with Electronic Driver Heat sink Capacitor and all other accessories including connection, earthing etc complete as per specification and IP20, P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 40 watt

Supplying, installation, testing and commissioning of following LED tube light fitting including batten with Electronic Driver Heat sink Capacitor complete with all other accessories on surface/ in false ceiling, including connection, earthing etc complete as per specification and IP20, P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 18/20 watt {4 feet}

Supplying, installation, testing and commissioning of following 230/250 volts LED street light fitting with all accessories like driver, heat sink made of die cast aluminium with IP 66 protection and 15 KV surge protection on pole bracket, including connection, earthing, Separate housing for driver etc complete as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 120 lumens /watt. 150 watt

Supplying and fixing metal clad busbar chamber made of 2.0 mm thick CRCA MS powder coated sheet with 4 strip copper busbars of following capacity and length, complete with all accessories, including earthing the body etc. as per specification. 200 amps x 900mm long

Providing and making interconnection in cubical panel between BBC and switchgears with following size FRLS PVC insulated copper conductor wire lead of length upto 50cm including providing copper thimbles on both ends as per specification (To be measured separately for each phase/ neutral). 35 sqmm (125 amps)

Providing and making interconnection in cubical panel between BBC and switchgears with following size copper strip of length upto 50cm as per specification (To be measured separately for each phase/ neutral). 60x5mm (500 amps)

Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and following depth made out of not less than 2 mm thick CRCA MS powder coated sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ammeters etc as per specifications including powder coating painting but without busbars, switchgears and other accessories etc complete as per specification. Above 450 mm and upto 600 mm deep

Supply, installation, testing and commissioning of 4 pole (3 phase + neutral) copper (electric grade) bus bars in existing cubicle type compartmentalized wall/ floor mounted panel board along with suitable size and shape insulators, necessary bolts and nuts etc complete as per specification. 500 amp (60x5mm)

Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as per specification, IS/ IEC: 60947-2 and Ics = 100 % Icu. 4 pole MCCB, 100A, Adjustable Microprocessor Release, 50KA

4 pole MCCB, 320A, Adjustable Microprocessor Release, 50KA

4 pole MCCB, 630A, Adjustable Microprocessor Release, 50KA

Supplying and fixing on surface/ recess prewired horizontal type following way, 415 volts TP&N, MCB distribution board of sheet steel phosphatized and powder painted complete complete with loose wire box, terminal blocks, tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, duly prewired with suitable size FRLS PVC insulated copper conductor up to terminal blocks including interconnections, earthing etc. as per specification. (But without MCB/ RCCB/ Isolator) 8 way (4 + 24), Double door

Supplying and fixing SP MCB, 240 volts, 'B' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 6 amps to 32 amps

Supplying and fixing TP&N MCB, 440 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 63 amps

Providing and fixing metal clad, TP&N 415/500 volts, By Pass Switch Unit with sheet steel enclosure including drilling holes on the board, connections, earthing the body, testing and commissioning etc. as per specification. 200 amps

Providing and fixing following rating current transformer in existing cubical panel including, connections, testing and commissioning etc. as per specification. 630 amps

Providing and fixing penal mounting 230 volt LED type indicating lamp in existing cubical panel including, connections, testing and commissioning etc. as per specification.

Providing and fixing panel mounting digital type VAF (Volt-amp-frequency combined) Multi Function meter of size 100x100 (NS) in existing cubical panel including connection, testing and commissioning etc. as per specification.

Supplying, installation, testing and commissioning following rating single phase in single phase out ON-LINE UPS including connection etc but without batteries as per specification. 5 KVA with DC bus voltage 180 V

Supplying, installation, testing and commissioning following rating (Sealed Maintenance Free) lead acid battery including connection as per specification. 65 AH

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe, with charcoal and salt as per specification and IS Code 3043: 1987(R 2016)

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode at 0.5 Metre depth below ground level including excavation and refilling the trench etc. as per specification.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as per specification.

Providing maintenance free earthing with following size GI pipe including making bore pit of minimum 150mm dia, providing and laying approved make Earthing Electrode of Pipe-in-Pipe technology as per IS 3043(R 2016) -1987 made of corrosion free G.I. Pipes having outer pipe of 80mm dia and inner pipe of 50mm dia and filling with specified qty highly conductive compound around pipe and above that with soft soil in bore pit complete and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. as per specification: With 2 metre long GI Pipes and 25 kg back filling compound.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, copper tube, having single prong at top, with 85 mm dia 3 mm thick copper base plate having 4 nos holes for fixing etc. complete as per specification.

Making jointing of copper tape (with another copper tape, base of the finial or any other metallic object) by reverting, sweating and soldering/ nut bolting of as per specification.

Providing and fixing copper tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as per specification.(For horizontal run)

Providing and fixing copper tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as per specification.(For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick copper strip, 125 mm long, with 4 nos. of tinned brass bolts, nuts, chuck nuts and spring washers etc. complete as per specification.

Providing and laying copper tape 32 mm X 6 mm from earth electrode directly in ground as per specification.

Supplying and laying ISI marked double wall HDPE pipe (IS 14930 Part II) having corrugation on the outer wall and plan surface on inner wall in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as per specification. 90 mm outer dia and 75 mm Inner dia

Supplying and fixing G.I. pipe along with wall or pole/ support with 2 Nos MS clamps for protection of under ground cable in approved manner including bolts and nuts or metal dash fasteners complete as per specification. 50 mm dia

Supplying and laying following sizes one number FRLS PVC insulated/XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade direct in ground at a depth not less than 40 cm and upto 90 cm including excavtion, sand cushioning, protective covering and refilling the trench etc as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1). 3.5 x 35 sq. mm.

3.5 x 150 sq. mm.

4 x 16 sq. mm.

4 x 25 sq. mm.

Supplying and making end termination with brass compression gland and aluminum lugs for following size armoured aluminum conductor power cable of 1.1 KV grade as per specification. 3½ X 150 sq. mm (45 mm)

4 X 16 sq. mm (22 mm)

Supplying, fixing and cramping suitable size and all type Copper ferule/ lugs to following size 1.1 KV grade power cable core / lead, pressed with high pressure cramping tool including connection to switch gear/ MCCB etc as per specification. . 10 sq. mm

Designing and providing suitable RCC foundation in Cement Concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) for 3 mere to 12 metre high GI octagonal pole including steel reinforcement form work, embeding 2 nos 50mm dia PVC pipe for cable entry in each foundation, excavation disposal of surplus soil and curing etc. as per specification.

Supplying, installation, testing and commissioning of following capacity diesel Generating Set (alternator directly coupled to diesel engine) compete in all respect broadly comprising of following and as per CPCB 2 norms (upto date ammended), including following specification. A. Alternator : Self excited, brush less type, of following capacity, 3 phase, 415 volts 50 Hz, 4 pole, AC alternator complete with all accessories.B. Engine : water cooled diesel engine of suitable BHP for rated alternator at 1500 rpm, turbo charged, direct injection type, 4 stroke, 4/6 cylinder including specified size fuel tank of approved design and shape duly calibrated and painted with one coat of primer and two coats of synthetic enameled paint of approved colour, residential type silencer with exhaust MS pipe (upto 2 metre beyond silenser) duly wrapped with asbestos rope of legging of specified quality and specification.C. AMF Panel : Cubical, compartmentalized, AMF panel board with all suitable size power and control contactors, switches, meters and other accessories, internal wiring, connection, inter-connection etc. for trouble free smooth functioning of DG Set complete with battery charger and leads as per specification.D. Base Plate : Common base plate of required size for mounting of engine alternator set fabricated from MS channel and vibration damping arrangement with cushy foot mounting i/c painting etc. as per specification. 200 KVA

Supplying, installation, testing and commissioning of submersible pump set for water supply system with submersible motor directly coupled to multi-stage submersible pump of specified discharge capacity, head, delivery size in existing bore well including 2 sets of suitable size holding clamps made out of 50 mm X 6 mm MS flat, connection with suitable submersible cable of standard length etc. as per specification and IS: 694 (2010). Note: submersible Cable should be rust proof, safe from oil / Grease and under water Chemical / abrasion Resistant. 2.0 HP, single phase

Supplying and fixing following dia HDPE pipe PE-80 Grade (8kg/sqcm) in single length in the suction/ delivery line of water supply pump etc. as per specification. 32 mm outer dia

Supply, installation, testing and commissioning of 1-3 HP 1 phase submersible motor starter cum control wall/ floor mounted type made out of not less than 1.6 mm thick MS sheet and comprising of following panel mounting switchgears there in including connection inter-connection etc. as per specification. a) Phase indicating lamps with fuses and toggle switches 1 set b) 1/2/3 HP 1 phase DOL starter with over load and no volt relay 1 No c) 25 A "C" curve DPMCB 1 No d) Voltmeter 0-250 V 1 set e) Ammeter 0-10 A 1 set

Supplying and fixing M.S. clamp 50 cm long made of 50mmx5mm thick M.S. Flat for holding the pipes and submerable pump set as per specification.

Supplying and fixing 300 mm dia 2 mm thick M.S. sheet cover with 3 cm edge in two past on tube well bore pipe as per specification

Supplying, laying and fixing following size submersible cable along with GI/PVC/HDFC pipe line or laid in ground etc as per specification and IS: 694 (2010). Note: Cable should be rust proof, safe from oil / Grease and under water Chemical / abrasion Resistant. 3x4.0 sqmm

Supplying and making water proof joint with heat shrinkable joint kit including copper ferrules for following size of 3 core submersible copper conductor cable of 1.1 KV grade as per specification. 3x4.0 sqmm

Supplying and laying of approved make stainless steel wire rope of 6 mm dia for support of submersible pump set complete with tying to pump set and pump holding clamp.

Installation of split type Inverter/Non Inverter Air Conditioner unit, cooling unit on wall inside and condensing unit on out side wall/ ceiling/ floor at desired locations with existing standard length of copper piping with insulation and power cable including providing and fixing necessary good quality powder coated MS frame etc complete as per specification. (Extra length of copper piping and power cable shall be paid extra on linear basis)

Supply and fixing of approved make wall mounting type voltage stabilizer with input volts 160-250, output volts 200-240 volts and double step relay on desired location with necessary fixing material including connection etc complete as per specification. 5 KVA

Supply, connecting and fixing extra length of copper piping for split type air conditioners of following dia and approved quality with insulation sleave etc complete as per specification 5/8 "

Supplying and fixing good quality powder coated MS frame for installation of out door unit of split type Air Conditioner at desired location with atleast 6 nos steel fastners etc complete as per specification

Supplying, connecting and fixing 15mm dia PVC flexible drain pipe (reinforced with nylon threads) in drain outlet of split type air conditioners etc complete as per specification

Supply and filling up required quantity of R-22/R-32/R-410 refrigrent in existing window/ split air conditioners as per manufacturers specification including checking for leakage before and after filling, flushing the line with R-22/R-32/R-410 etc complete as per specification. 2.0 ton split type AC

Supplying of approved make Hiwall split Inverter type Air Conditioner unit with cooling unit (copper coil) and condensing unit (copper coil) including 5 years compressor warranty and standard length of upto 5 metre of copper piping with insulation etc complete as per specification 2.0 Ton split type Inverter AC {5 Star}

Supplying and fixing of approved make Tower Air Conditioner unit with cooling unit and condensing unit with copper coil including standard length of upto 3 metre of copper piping with insulation etc complete as per specification. 4.0 TR

Supplying and fixing wall mounted storage/instantaneous type electric geyser, complete with inner copper container, heating element, thermostat, indicating lamp including inlet / outlet water pipe connection, electric connection testing and commissioning etc. as per specification. 15 Ltr. Capacity storage type geyser 5 star

Supplying , installation , testing and commissioning of 4 MP Bullet Camera weather & dust proof IP based Fixed Lens day/night Camera (IP67 , IK 10) , 1/3” 4MP PS CMOS Image Sensor, H.265 and H.264 triple-stream encoding, WDR(120dB), Day/Night Support, UL ,CE FCC Certified as per the specifications.

Supplying , installation , testing and commissioning of 2 MP DOME Camera weather & dust proof IP based Fixed Lens day/night Camera (IP66) 2Megapixel CMOS Image Sensor,H.265 / H.264 triple-stream encoding , WDR(120dB), Day/Night UL, CE, FCC Certified as per the specifications.

Supplying , installation , testing and commissioning of 32 Channel NVR 8 Sata Port Up to 32 channel IP camera input , Max 320Mbps incoming bandwidth , Smart H.265+/H.265/Smart H.264+/H.264/MJPEG , Up to 12MP resolution preview and playback , Support 8 SATA HDDs up to 10TB each,1 eSata , 4 USB(2 USB3.0, 2USB2.0) , 2 HDMI / 2 VGA simultaneous video output ,ONVIF Version 2.4 conformance , Alarm In / out 16/6 , Two way talk 1 Channel Input, 2 Channel Output RCA , 1 RS485, 1 RS232 , 2 RJ-45 port (10/100/1000Mbps), Support ANPR Camera as per the specifications.

Supplying, installation, testing and commissioning of 8 Port Giga PoE Switch 10/100/1000 8 Port with 2 Giga RJ 45 uplink, PoE switch, AI Extend, AI Vlan as per the specifications.

Supplying , installation , testing and commissioning of 8 TB Surveillance Hard disk drive Complete as required

Supplying , installation , testing and commissioning of 6U Indoor Rack Wallmount 6U 450D With Front Glass Door Lock & Key 550 6U - loaded with cable manager + PDU + Fan complete as required.

Supplying, installation, testing and commissioing of following size LED Monitor, table/wall mount with inbuild speaker minimum 5Wx2, with minimum 1 No of HDMI and USB port including remote control, connecting cable, batteries and all accessories, connection etc complete as per specification. 55 inch

Supply, installation and testing for HDMI cable.

Supplying , installation , Testing and Commissioning of UHF Wireless Cardioid Condenser handheld microphone system with Frequency Response of 60 Hz to 16 kHz , RF Sensitivity 10dBμV (S/N 60dB @ 20 kHz deviation) or better, Total Harmonic Distortion <1.0% (at 1 kHz, ±20 kHz deviation) or better, Dynamic Range > 108dB or better, on/off switch operating range 60 mtrs or better, RF Power Output: 10 mW or better, maximum Output level XLR / Balanced: +4 dBV & 6.3 mm (¼") / Unbalanced: -2 dBV with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of UHF Wireless Cardioid Condenser lapel microphone system with Frequency Response of 60 Hz to 16 kHz , RF Sensitivity 10dBμV (S/N 60dB @ 20 kHz deviation) or better, Total Harmonic Distortion <1.0% (at 1 kHz, ±20 kHz deviation) or better, Dynamic Range > 108dB or better, on/off switch operating range 60 mtrs or better, RF Power Output: 10 mW or better, maximum Output level XLR / Balanced: +4 dBV & 6.3 mm (¼") / Unbalanced: -2 dBV with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of Advanced digital audio processor with open architecture software-configurable functionalityComprehensive library of DSP algorithms optimised for installation applications, 8 Channels of wide band Acoustic Echo Cancellation (AEC) for telephone and video conferencing, Auto mixer functionality for multiple microphone applications, Optional Dante card for IP-based audio networking, PC-based software with intuitive graphical user environment, 10 high-headroom analogue universal mic/line inputs,6 electronically balanced low impedance line level outputs, USB audio connection for integration with computer based audio, ULTRANET digital audio transport output for connection to compatible devices Ethernet port for software configuration via CAT5/5e cable with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of Wall Mounted two way full Range speaker with Minimum 2 x 3.5" LF or 1 x 5.25" LF or better with 1" HF with a Frequency Response(-10dB):- 65Hz-20Khz & Long Term Program Power Handling of 120W or more. The Loudspeaker should have a Sensitivity(1W/1m) of atleast 90dB with a Max. Peak SPL of >114dB. Speaker shoudl have 70/100 volt transformer taps with upto 60 watts tapping. The Sound Dispersion should be 90x70 Degrees or better complete with wall mount Bracket of same OEM with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of Passive Column Array Loudspeaker with 7 Mid Range Drivers and FAST Dispersion Control for Installation Applications (EN 54 Certified),7 x 3.5" full range drivers with 150 W RMS Power @ 8 Ohms with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of Dual Channel Audio Amplifier Professional 1700-Watt (Per Channel 700 to 800 Watts into 4 Ohms OR Per channel 400 to 500 Watts into 8 Ohms OR 1600 to 2000 Watts into 8 Ohms (bridge mode)Stereo with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of Mono Connectors Pin with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of RCA Connectors Pin with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of MXLR (Male External Line Return) Connectors Pin with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of FXLR (Female External Line Return) Connectors Pin with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of EP 3.5 MM Connectors Pin with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of MXLR Connector Socket with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of FXLR Connectors Socket with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of Patch box with 04 connetors options for mic & stage monitor

Supplying , installation , Testing and Commissioning of 2.5Sq.mm Speaker cable Cross sec Area 1.5 sqmm, No of Strands 75 , Size of Strands 34 , Cond.Type ATC Speaker Cable - Copper 2Core, Twisted, Tin Coated, Shielded 2.5SQMM (70/.2) ATC 2/C SPEAKER CABLE 14AWG with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of Heavy Microphone Cable AWG NOM Insulation Dia. Shield NOM NOM Conductor Center Inches mm Construction Jacket Dia. Capacitance Resistance Canductor (Min.) Inches mm (Pf / mtr.) Ohm / km (Max.) 24 AWG 0.053 1.35 80% 0.232 5.9 68(Cond. To Cond.) 91.1 with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of Power Management (Constant Voltage / Frequency Stabliser): Power Conditioner, with a built in 3 Way Sequencer that provides sequenced switching with a fixed interval, turning them on & off ina preset sequence. Adjustable Protection Levels : Over voltage 245-275 VAC Under voltage 170-220 VAC with Disable %-Over Frequency 50.5-55.0 hz with Disable Under Frequency 45.5-49.5 hz with Disable with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of 17U Equipment Rack, with Metal Side Panel, Back Door, Front Glass Door, Floor Wheel, 15u PDU Unit, Cooling FAN, Cable Manager, Counter Shelf with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning Cardioid Condenser Gooseneck Microphone with goosenck length of 415mm or more. Flexible gooseneck head for accurate positioning. Shock Mount to be inlcuded with Microphone from same OEM with Frequency Response 70 Hz - 16,000 Hz; It shall be capable of handling sound input levels up to 134 dB with a dynamic range of 106 dB. Nominal open-circuit output voltage shall be 12.0 mV at 1 V, 1 Pascal or better, Signal-to-noise ratio of 66dB,1kHz at 1Pa or better. Support 11V to 52V phantom power for operation. Impedance 100 ohms or better complete with Foam Windscreen with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning Active Speaker 600 Watt 2 Way 10" Full Range Powered Loudspeaker with DSP Technology Components 1 x 10" LF driver 1 x 1" HF driver Connectors Mic/Line input: combo jack/female XLR wired pin 2 hot Mix out: male XLR wired pin 2 hot Frequency Range 55 Hz–18 kHz ±3 dB 50 Hz–20 kHz -10 dB Dispersion @-6 dB pts 90° H x 60° V Max SPL (peak) 126 dB Equalisation Bass: ±6 dB @ 80 Hz Treble: ±6 dB @ 12 kHz Max Output Power LF: 500 W HF: 100 W with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning Active Speaker 1100 Watt 2 Way 15" Full Range Powered Loudspeaker with DSP Technology Components 1 x 15" LF driver 1 x 1" HF driver Connectors Mic/Line input: combo jack/female XLR wired pin 2 hot Mix out: male XLR wired pin 2 hot Controls Level, Line/Mic, Low Cut, Speech/Music, Bass and Treble, Front LED, Mains on/off requency Range 45 Hz–18 kHz ±3 dB 40 Hz–20 kHz –10 dB Dispersion @-6 dB pts 90° H x 60° V Max SPL (peak) 130 dB Equalisation Bass: ±6 dB @ 80 Hz Treble: ±6 dB @ 12 kHz Max Output Power LF: 1000 W HF: 100 W with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning Active Speaker 2200 Watt 18" Powered Subwoofer Components 1 x 18" LF driver Connectors Input: 2 x female XLR wired pin 2 hot Thru: 2 x male XLR wired pin 2 hot Frequency Range 40 Hz–100 Hz ±3 dB 30 Hz–150 Hz -10 dB Dispersion @-6 dB pts N/A Max SPL (peak) 134 dB (half space) Boost Frequency +6 dB @ 40 Hz–90 Hz, Q=1 Max Output Power 2200 W Input Sensitivity +4 dBu @ centre position for full rated power Input Impedance 10 kO unblanced, 20 kO balanced with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning 24‑channel Compact Mixing System, 24 input channels (16 Mic/Line + 4 Mic/Stereo-Line) 2 High-Quality editable effects, MIC input to Master A L/R outputs, +16 dBu, typical < 0.01% Frequency Response, -3 dB, ref. 1 kHz, any input to any Mixer output 15 Hz to 20 kHz, Equivalent Input Noise, MIC input, A-weighted, 150 ohms -130 dBu with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning Wall Hanging Arrangement for Speaker Metal Wall Bracket with necessary accessories to mount the speakers on wall with all necessery terminals and Connectors.

Earth work in soft rock with all lead and 1.5 metre lift, dressing, stacking excavated strata including refilling with excavated soil in trench / pit to ground level complete as per specification

UOM Name

Percentage

Per mile

Siemens Per meter

Activity unit