SPECIAL REPAIRS TO TYPEII QTR BLOCK NO P 15 AND ADDITION ALTERATION OF GALVALIUM SHEET SHED AND THREE PHASE ELECTRICITY CONNECTION FOR AIR COMPRESSOR AT AUNDH CAMP PUNE

Amount

Removing of old water proofing treatment and cleaning the surface of slab with wire brush, removing dust,foreign materials and removing the rubbish off the site to a distance n.exc 100m all as specified and directed by Engr-in-Charge.

M & L for PCC M-15 grade (nominal mix) using 12.5 mm graded stone aggregate) on roof top for maintaining of slope coving,benching etc all as specified and directed by Engr-in-Charge.

M&L for rendering 10 mm thick on concrete surfaces of roof in CM 1:3 mixed with liquid water proofing compound as per manufactures instructions finishing even and smooth to receive water proofing treatment complete without using extra cement all as specified and directed by Engr-in-Charge. Note :- Liquid WPC shall be measured and paid seperately under relevant item of BOQ.

M & L for applying APP (Atactic Poly Propylene) bitumen membrane 3mm thick APP modified weight not less than 3.60 Kg/Sqm reinforced with non woven polyester fibre of weight 160 gms/sqm as center core and without multiple layers of polyethylene, finished on top and bottom with 7 micron thick flammable polyethylene, applied by thermo fusion using LPG torch on the bottom portion of the membrane, after applying a coat of bituminous primer 0.40Kg/Sqm over roof ( An overlap of 100mm & 150mm shall be provided on sides and ends respectively ) all as per manufacturers instructions.

Taking up or down steel tubing 20 mm dia and connection including cleaning for refixing for following bore of pipe, complete all as specified and directed by Engr-in-Charge.

Taking up or down steel tubing 15 mm dia and connection including cleaning for refixing and removing to store for following bore of pipe, complete all as specified and directed by Engr-in-Charge.

Supplying & fixing to walls and ceiling 20 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and directed by Engr-in-Charge.

Refixing old steel tubing and connection of 20 mm dia in new or old position walls, ceiling ,floor etc

Supplying & fixing to walls and ceiling 15 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and directed by Engr-in-Charge.

Refixing old steel tubing and connection of 15 mm diain new or old position walls, ceiling, floor etc

S&F in repairs, gun metal globe or gate valves 20 mm dia ,with iron wheel head,screwed both ends for iron pipes complete all as specified and directed by Engr-in-Charge.

Dismantling water tank of any description or capacity 500 ltrs all as specified as directed.

Supply and fix 500 liters capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc complete.

S & F in repairs ball brass valve 20 mm dia high pressure with polythine float and fly nut for following bore of pipe, complete all as specified and directed by Engr-in-Charge.

Taking down chowkats and frame n.exc 1.5 Sqm incl shutter with out taking off shutters from frame all as specified and directed by Engr-in-Charge.

Taking down chowkats and frame exc 1.5 Sqm and n. exc 4.0 sqm incl shutter with out taking off shutters from frame and removing from site specified and directed by Engr-in-Charge

Taking down wooden shutters exc 1 sqm and n exc 2 sqm each complete

S&F 125x60 mm Pressed steel frames made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with one shop coat of red oxide primer complete, as specified, supplied and fixed all as specified and directed by Engr-in-Charge.

S&F 105x60 mm Pressed steel frames made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with one shop coat of red oxide primer complete, as specified, supplied and fixed all as specified and directed by Engr-in-Charge.

S&F in repairs Prelaminated particle board 18/19 mm thick, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work all as specified and directed by Engr-in-Charge.

S&F in repairs Second class hard-wood clean sawn timber framed and fixed in scantlings all as specified and directed by Engr-in-Charge.

S & F in repairs Continuous (piano) hinges, width of flaps 30mm, brass, bright finish or electrogalvanised all as specified and directed by Engr-in-Charge.

S&F Powder coated (Powder coating shall not be less than 50 micron of approved colour) aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed by Engr-in-Charge.

S&F powder coated (Powder coating shall not be less than 50 micron of approved colour) aluminium three track window and ventilator shutters, sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings all all as specified and directed by Engr-in-Charge. Note : Glazing shall be measured and paid as supply only under relevant item of BOQ. Fixing rate is deemed to be included under limit rate quoted.

S&F powder coated (Powder coating shall not be less than 50 micron of approved colour) aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed by Engr-in-Charge. Note : Glazing shall be measured and paid as supply only under relevant item of BOQ. Fixing rate is deemed to be included under limit rate quoted.

S&F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0

Supply only 5mm thick Sheet glass, ordinary quality in square n.exc 0.5 sqm in each pane.

Supply only 5mm thick Sheet glass, obscured or frosted square n.exc 0.5 sqm in each pane.

M & L for 35mm thick flush shutters solid core constructions with block board core, ply wood face panels commercial type on both side all as specified and directed by Engr-in-Charge.

S & F 30 mm thick 2nd class H.W glazed or skeleton shutter open rebated divided intosquare with plain chamfered or rounded mitred and rebated with out sash bar and prepared to receive gauze or glaze, size of members as clause 8.20 (a) of SSR Part-1.

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing.

M&L Factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front Face & 2mm Plan colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing.

S&F in repairs stainless steel wire cloath 0.56 mm nominal dia of wire and average width of aperature 1.18mm including fixing with wooden/steel batten all as spd & directed by Engr-in-Charge

M & L for Aluminium alloy barrel tower bolts of stove enamelled blackwith bright bolt and fixed 150mm long all as specified and directed by Engr-in-Charge.

S&F butt hinges medium weight colled rolled mild steel 100 mm and fixed all as specified and directed by Engr-in-Charge.

S & F Aluminium alloy sliding door bolt 300 mm long, plate type, stove enamelled black with bright bolt not less than 12 mm dia with and incld mild steel min of 6 bolts and nuts, 4 on bolt plate and 2 on stapleplate fixed / welded to door shutter/frame all as specified and directed by Engr-in-Charge.

M & L for Aluminium alloy pressed oval type handles stove enamelled blackfor doors 150 mm long all as specified and directed by Engr-in-charge.

Taking down cement plaster in any description incl racking out joints hacking for key and scrubbing down with water etc all as specified and directed by Engr-in-Charge.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises all as specified and directed by Engr-in-Charge.

M&L for Rendering 10mm thick, on fair faces of brick work or concrete surfaces of walls in CM 1:6 finished even surface all as specified and directed by Engr-in-Charge

M&L for Rendering 10mm thick, on concrete surfaces of ceiling in CM 1:4 finishing the surface even and smooth complete all as specified and directed by Engr-in-Charge

M&L rendering 15 mm thick (10mm + 5mm) plaster on other than fair face of brick work in CM 1:4 and surface finished even and fair by mixing liquid water proofing compound as per manufacturers instructions complete. Note :- Liquid WPC shall be measured & paid seprately under relevant item of this BOQ.

Supply only liquid water proofing compound hydroseal-W+ or eqivalent (for plaster hardening, to contol efflorescence & fungal growth) as approved by GE.

M&L for providing and carry out water proofing treatment to toilets, sunken floors slabs, wet areas etc, after proper surface preparation, carry out cementitious injection grouting at leakage points using cobex 100 plasticised expansive grount admixture, application of polymer modified vatta at slab and wall junction using nitobond SBR latex- screed modifier cum bonding agent and application of two coats of brush bond RFX - two- Part acrylic polymer modified cementtious elastometic water proof and protective coating etc, complete including all tools and tackles as per manufactures specification.

M & L for PCC M-5 grade (nominal mix) uisng 40mm graded stone aggregate as in filling, mass concrete, for sunkun floor.

M&L Non Skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles laid over and including cement screed 15mm thick in CM 1:4 complete all as specified and directed by Engr-in-Charge.

M&L coloured Non Skid ceramic tiles 400 x 400 x 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles laid over and including cement screed 15mm thick in CM 1:4 complete all as specified and directed by Engr-in-Charge.

M&L coloured Glazed ceramic tiles in vertical surface of size 300mmx450mm x 6 to 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles laid over and including cement plaster 10mm thick as in backing coat in CM 1:4 complete all as specified and directed by Engr-in-Charge.

M&L for 18 - 20mm thick machine cut machine polished Kota stone slab flooring laid and jointed in neat cement slurry mixed with pigment to match the shade including cutting and polishing over and including 15 mm thick screed bed in CM 1:3 complete all as specified and directed by Engr-in-Charge.

All as per item No 49 above but in riser, step, skriting, dados and pillar over and including 10 mm thick plastering in cement morter 1:3 all as specified.

M&L Granite slab 20 mm thick machine cut bedded and jointed with grey cement and pointed with white cement and adhesive of pigment to match the shade incl cutting and polishing laid over and including cement screed 10mm thick in CM 1:4 complete all as specified as directed by Engr-in-Charge.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations.

S&F in repairs kitchen sink with drainage board made of stainless steel 1mm thick with plugs washers and wastes incl bedding in CM to drawf wall incl fitting cantilever brackets and connecting union to pipe overall size 915mm x 460mm and bowl size 410mm x 330mm x 160mm.

S&F in repairs steel plate rack of 900mm x 750mm x 200mm all as specified and directed by Engr-in-Charge.

S&F in repair 20 mm dia, chromium plated curtain rod with fixing brackets, stops, rollers etc.complete all as specified and directed by Engr-in-Charge. Note : Bracket shall be measured & paid seperately under relevant item of this BOQ.

S&F in repairs bracket of fancy type curtain rod powder coated 20mm dia including fixing to walls with MS full screws (including fixing of wooden pieces of required size of walls) all as specified and directed by Engr-in-Charge.

S&F in repairs aluminium anodised Tubular towel rail 20mm dia, D type, 60cm long between flanges complete.

S & F in repairs stopvalves cast copper alloy screwed down high pressure withcrutch or butterfly handle screwed both ends for iron pipe 15 mm dia all as specified and directed by Engr-in-Charge.

S & F in repairs bib taps CP Brass with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule 15mm dia all as specified and directed by Engr-in-Charge.

S & F in repairs brass CP shower rose 125mm size with swivel joint incl fixing to steel pipe fixed in repairs all as specified and directed by Engr-in-Charge.

M & L for 75mm thick PCC M-7.5 grade (nominal mix) uisng 20mm graded stone aggregate as in Plinth, Path, floor with fair finish surface without using extra cement all as specified and directed by Engr-in-Charge.

S & F in repairs viterious china wash basin white flat back size 550 x 400 mm excluding taps waste chain and plug and porcelain stopper but incl necessary brackets CP wastes and other fittings all as specified and directed by Engr-in-Charge.

S & F in repairs pillar taps chromium plated cast copper alloy with capstan heads screwed down high pressure with or without lettered Hot Or Cold Withlong screwed shanks and fly nuts screwed for iron pipes 15mm dia all as specified and directed by Engr-in-Charge.

S & F in repairs water closet (Squat Pattern) complete incl provn of lime concrete bedding Orissa pattern size 580 x 440mm white integral foot rests (excluding flush pipe or flushing cisterns) including connection to trap and flushing pipe anti syphonage pipe etc complete and making good to floor.

S & F in repairs PVC High/Low level flushing cistern 10 litres capacity including all fittings i.e float valve, syphon, flushpipe, brackets all as specified and directed by Engr-in-Charge.

M&L for PCC M-15 grade (nominal mix) using 12.50mm graded stone aggregrate as in coping hold fast block bed bolck filling pressed steel door frame etc all as specified.

M&L painting to wooden surfaces of any description over 10 cm width or girth incld prepration of new or untreated surface and applying two coat of synthetic enamel paint over one coat of pink primer all as specified.

M&L for preparation newly plastered surfaces of walls/ceilings and applying two coats of weather proof acrylic exerior paint (100%) Acrylic) over one coat of self primer including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and directed by Engr-in-Charge.

M&L for complete removal of existing treatment of old surfaces and applying two coats of weather proof acrylic exerior paint (100%) Acrylic) over one coat of self primer including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper of approved colour and pattern over a coat of primer over a coat of wall care putty not less than 1mm thick finished even and smooth complete all as specified and directed by Engr-in-Charge.

M&L for complete removal of existing treatment & applying two coats of oil bound distemper of approved colour and pattern over a coat of primer over a coat of wall care putty not less than 1mm thick finished even and smooth complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash over a coat of wall care putty not less than 1mm thick finished even and smooth complete all as specified and directed by Engr-in-Charge.

M&L for Complete removal of existing treatment on ceiling & applying applying three coats of white wash over wall care putty not less than 1mm thick finished even and smooth complete all as specified and directed by Engr-in-Charge.

Demolition of brick work PCC block mansonry or stone boulder masonary built in cement mortar including all quoins arches pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles.

M&L for Pre-cast cement concrete block masonry of PCC 1:3:6 Type C1 using 20mm graded stone aggregate with solid blocks straight or curved on plan , exc 6m mean radius and exc. 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

Taking down drain pipes (any size or pattern), including all fittings, T, bends,etc., including cleaning or refixing (measured overall as fixed along the centre line over fitting and accessories)

S&F 110mm dia PVC (SWR) pipes type 'A' single socketed in any length with rubber ring joints fixed to walls.

All as per item No 78 above but except pipe complete.

S&F 75mm dia PVC (SWR) pipes type 'A' single socketed in any length with rubber ring joints fixed to walls.

All as per item No 80 above but exept pipe complete.

S&F 110mm dai PVC (SWR) bends any radius complete.

S&F 75mm dai PVC (SWR) bends any radius

S&F 110mm dia PVC (SWR), junction single, (Single T) equal or unequal complete.

All as per in item No 84 above but except fittings.

S&F 75mm dia PVC (SWR), junction single, (Single T) equal or unequal

All as per item No 86 above but except fittings.

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings all as specified and directed by Engr-in-Charge.

M&L for 75mm thick, PCC M-7.5 grade (nominal mix) using 40 mm graded stone aggregates as in sub base of floor/ pavement, all as specified and directed by Engr-in-Charge.

M&L for 75mm thick M-15 grade (nominal mix) using 20mm graded stone aggregate as in floor of all as specified and directed by Engr-in-Charge.

M&L for Cement concrete M-15 grade (nominal mix) using 20mm graded aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, all as specified and directed by Engr-in-Charge.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in cladding to wall, fixed with self tapping screws complete all as specified.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to Fe-410-W

S&F Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated)

M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:6 all as specified and directed

S&F of 35mm thickness 2nd class HW rail and style of factory made shutter of Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed by Engr-in-Charge.

S&F of 2nd class hardwood for Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed all as specified and directed by Engr-in-Charge.

Cutting openings, through brick walls for door, window and other openings or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc.. to store and removing rubbish to a distance not exc. 50m complete all as specified.

Forming jambs, etc. to openings (to foregoing item) in CM 1:4 in cement mortar, including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete all as specified and directed by Engr-in-Charge.

S&F of Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M&L for preparation of old steel surfaces of any description, not otherwise descri-bed, over 10cm width or girth and applying one coat of synthetic enamel paint all as specified and directed by Engr-in-Charge.

M&L for preparation of new steel surfaces of any description, not otherwise descri-bed, over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of red oxide primer all as specified and directed by Engr-in-Charge.

S&F of 300mm length Aluminium anodised, barrel tower bolts of extruded section and fixed all as specified and directed by Engr-in-Charge.

S&F of 150 mm size Aluminium handles, cast type, anodised all as specified and directed by Engr-in-Charge.

S&F of 150mm length Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor

M&L for preparation of old wooden surfaces of any description, not otherwise descri-bed, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-Charge.

S&F of 250 mm length aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed all as specified and directed by Engr-in-Charge.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, such as switches, ceiling roses, pendants, regulators, sockets etc. removing materials to store for keeping in safe custody or for taking credit(credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

M & L for point wiring with 1.5 sqmm (nominal area) single core multi stranded copper conductor PVC insulated but unsheated FRLS cable 1100 Volts drawn in and including PVC concealed conduit Medium grade ISI marked of suitable size including its accessories such as tee, bend ,elbow, socket and chisselling on wall complete also including 1.5 sqmm PVC insulated and PVC unsheathed single core multistranded copper conductor FRLS cable 1100 V grade as earth wire including "concealed" MS terminal box ISI marked with modular cover plate of suitable size as per site requirement for housing switch, socket, regulators etc complete. Note : Cost of modular plate is deemed to be included under unit rate quoted.

One light / bell / ceiling fan point controlled by one way modular switch 5/6 Amp.

One 3 pin 5 Amps socket point controlled by one Modular switch on independent board complete.

One 3 pin 5 Amp socket outlet on same board with other switches

M & L for point wiring with 2.5 sqmm (nominal area) single core multi stranded copper conductor PVC insulated but unsheated FRLS cable 1100 Volts drawn in and including PVC concealed conduit Medium grade ISI marked of suitable size including its accessories such as tee, bend ,elbow, socket and chisselling on wall complete also including 2.5 sqmm PVC insulated and PVC unsheathed single core multistranded copper conductor FRLS cable 1100 V grade as earth wire including "concealed" MS terminal box ISI marked with modular cover plate of suitable size as per site requirement for housing switch, socket, regulators etc complete. Note : Cost of modular plate is deemed to be included under unit rate quoted.

One 3 pin 16 Amps power socket outlet controlled by one Modular switch on independent board complete.

One light point controlled by two way switch on independent board complete.

S & F switch modular switch 1 way 6A 1 module complete all as specified and directed by Engr-in-Charge.

S & F switch modular switch 2 way 6A 1 module complete all as specified and directed by Engr-in-Charge.

S & F switch modular bell push 6A 1 module complete aall as specified and directed by Engr-in-Charge.

S & F switch modular socket 6A 2/3 pin combined 2 module complete all as specified and directed by Engr-in-Charge.

S & F switch modular socket 16A 2/3 pin combined 2 module complete all as specified and directed by Engr-in-Charge.

S & F switch modular switch 1 way 16A 1 module complete all as specified and directed by Engr-in-Charge.

S & F modular fan regulator step type two module.

S & F electric bell Ding Dong, AC 230 volt complete all as specified and directed by Engr-in-Charge.

S & F LED building security / street light 35/36 W IP 65 with make Halonix cat part - HLSLD-14-36-W-CWDL-R, Bajaj and equivalent make

S & F LED tube light along with fixture, 22 W Aluminium extruded housing.

Supply & fix PVC angle holder complete all as specified and directed by Engr-in-Charge.

Supply & fix LED batten, 10 W Aluminium extruded housing complete

S & F MCB DP 40-63A "C" curve all as specified and directed by Engr-in-Charge.

M&L for submain wiring in PVC conduit with two runs 6sq mm and one runs of 6 sqmm for earth continuity1100 volt grade PVC insulated unsheathed FRLS grade copper conductor cable single core multistandard ISI marked (IS 694) drawn through and including 25 mm dia PVC rigid conduit heavy grade ISI maked (IS 9537 Part III ) including accessories such as bends, support etc complete including taking down existing submain wiring all as specified and directed. Note : Two runs of 6 Sqmm PVC cable and one run of 6 Sqmm earth cable & one run of PVC conduit shall be measured as one unit length.

Taking down defective distrubtion board including MCBs and wooden boards and S & F sheet metal enclosure distrubtion board for fixing MCBs with double door, TPN 4 way, 415 volts with 200 Amps rated bus bar complete all as specified and directed by Engr-in-Charge.

Supply and Fixing ceiling rose surface bakelite 65mm x 50mm three terminals complete all as specified and directed by Engr-in-Charge.

Disconnecting & taking down unserviceable material of earthing & material and labour for Earthing complete with GI earth plate 600mm x 600mm x 6 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level ) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI wire 4.0 mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES schedule Part-I and incl 15 mm bore light grade GI protection pipe (upto 7.5 metres beyond outer edge of earth pit) PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate in pit with 40mm thick RCC cover in reinforced cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate, reinforced with 8mm dia bar both way @ 150mm c/c, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and chaarcoal filling, necessary excavation and earth work complete.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10 cm grith all as specified and as directed.

Taking down defective distrubtion board including MCBs and wooden boards and S & F MCB DB SPN 8 way of any size and capacity double door type horizontal with 200 A busbar including disconnecting from mains and making good the disturbed surface complete all as specified and directed by Engr-in-Charge.

Taking down ceiling fan 1200 mm / 1400 mm sweep from any height and bringing down to floor for carrying out repair servicing and refixing in position after repair complete all as specified and directed. Note : Minor part such as rubber yoke, clamp, nut bollt cost shall be deemed to be included in unit rate quotated.

M&L for spray painting of ceiling fan 1200mm/1400mm sweep with one coat of synthetic enamel paint of same colour including preparation of old surface complete including numbering of fans as existing complete all as specified and directed by Engr-in-Charge.

Taking down serviceable kwh meter from site without any damage after completion of work re-fixing the kwh meter on existing position all as specified and directed by Engr-in-Charge. Note : Cleaning / painting / welding of damaged door of meter panel box by using sheet shall be deemed to be included in unit rate quoted.

S & F MCB SP of capacity 5A-32A "B" curve all as specified and directed by Engr-in-Charge.

S & F MCB TPN 40A "B" curve all as specified and directed by Engr-in-Charge.

Supply, laying, testing & commissioning XLPE cable insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35.00 sq mm 3.5 core.

Excavating in trenches not exc 1.5m wide and not exc 1.5m in depth for laying UG cable not exc 1.5m in depth and getting out in hard / dence soil.

Excavating in trenches not exc 1.5m wide and not exc 1.5m in depth for laying UG cable not exc 1.5m in depth and getting out in soft / loose soil

Returning, filling, incl spreading levelling, watering and well ramming in layers not exc 25cm all as specified and directed by Engr-in-Charge.

Removing excavated material to distance not exc 50m and depositing where as directed at a level not exc 1.5m above the starting point.

M&L for sand cushioning to under ground cable in trenches/existing cable trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep after laying and stretching the cable complete all as specified and directed by Engr in charge. Note:- Measurement shall be taken after gentling running.

Supply and laying reinforced precast concrete cable cover class LV, type 2, flat of size 250mm x 150mm x 40mm size for cable protection.

Supply and laying in trenches GI tubing light grade 50mm bore, ISI marked, for cable protection

M&L for road cutting and making good with M-10 grade (nominal mix) using 40mm graded stone aggregate of 150mm X 100mm inrespect of width and thickness complete all as specified and directed by Engr-in-Charge.

M&L for submain wiring in PVC conduit with two runs 2.5sq mm and one runs of 2.5 sqmm for earth continuity1100 volt grade PVC insulated unsheathed FRLS grade copper conductor cable single core multistandard ISI marked (IS 694) drawn through and including 1.5 sqmm PVC rigid conduit heavy grade ISI maked (IS 9537 Part III ) including accessories such as bends, support etc complete including taking down existing submain wiring all as specified and directed by Engr-in-Charge. Note : Two runs of 2.5 Sqmm PVC cable and one run of 2.5 Sqmm earth cable 1 run of PVC conduit shall be measured as one unit length.

Supply and fix switch piano flush type one way 6 Amps complete all as specified and directed.

Supply and fix exhuast fans AC single phase 230/240 V of size 600mm sweep metal body with louvers complete all as specified and directed.

Supply and fix in industrial wall mounted plug socket suitable for IP 44 degree of protection of 63 Amps rating 3p+N+E all as specified and directed. Make: L&T cat part DBPPS563SD or other Equivalent make in Legrand / Seimense / ABB all as specified and directed by Engr-in-Charge. Note : Rate of 63Amps MCB is deemed to be included in unit rate quoted.

Supply and fixing LED lights fitting 20W, (4 FT long ), 6500k temp 220V AC decorative box type with friver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable sice form ceiling rose complete. As dircted by Engr-in-charge. Make: Crompton/Wipro/Philips

Material and labour for fixing or passing through pipe, laid in trenches or fixed to pole/wall or fixed to LT panel board, armoured heavy duty electric cable with aluminium conductor, XLPE, 1100 Volts grade, cross- sectional area of size 10sqmm 4 core with all as specified and directed by Engr-in-Charge.

M/S JAYCONSTRUCTION CO

M/S VR KRNCH