PROVISION OF 02 NOS STATIC WATER TANK OF 50K. LITRE CAPACITY AND STANDBY PUMPING SET INCLUDING ALLIED WORKS AT OLD CANTT ALLAHABAD

Amount

Surface excavation in any soil not exceeding 30 cm deep and averaging 15cm deep and getting out soft / loose soil, complete all as specified and directed.

Excavating over areas, not exceeding 1.5 metre deep and getting out soft / loose soil, complete all as specified and directed.

Excavating over areas, exceeding 1.5 m deep but not exceeding 3 metre depth and getting out soft / loose soil, complete all as specified and directed.

Hardcore of broken stone or boulders of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

Plain Cement concrete 1:2:4 type B-1 (using 20 mm crushed stone aggregate) as in foundations, complete all as specified and directed.

RCC M-30 (20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and directed.

RCC M-30 (20mm graded stone aggregate) as in walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses, complete all as specified and directed.

Formwork to rough finished curved concrete surfaces of sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, complete all as specified and directed.

Formwork to rough finished curved surfaces of faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter, complete all as specified and directed.

TMT (high yield strength deformed) bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Rendering 5mm thick, on fair faces of brick work or concrete surfaces in cement and sand mortar 1:3, finished surface even and smooth without using extra cement, mortar mixed with WPC as per manufacturers instructions, complete all as specified and directed. NOTE:- Water Proofing Compound shall be measured and paid separately under respective items of this Schedule.

Supply only Integral water proofing compound ISI marked, complete all as specified and directed. NOTE:- Water proofing compound shall be mixed all as per manufacturers instructions only.

Neeru finish to plastering surface finished smooth, complete all as specified and directed.

Returning, filling in soils, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick, complete all as specified and directed.

Removing of surplus excavated material to a distance not exceeding 50metre and depositing where directed at a level not exceeding 1.5 metre above the starting point, complete all as specified and directed.

Plain Cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate), as in plinth protection, 75mm thick, complete all as specified and directed.

Plain Cement concrete 1:2:4 type B-1 (using 20 mm crushed stone aggregate) as in lintels upto 1.5metre clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs and the like, including weathering, slightly rounded or chamfered angles and throating, as directed complete all as specified and directed.

Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed.

Brickwork with flyash bricks, old size straight or curved on plan exceeding 6 metre mean radius, built in CM 1:6, complete all as specified and directed.

Demolition of Concrete work (un-reinforced) of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

Plain Cement concrete 1:2:4, type B-2 (using 40mm graded stone aggregate), as in sub base, 75mm thick, complete all as specified and directed.

Plain cement concrete 1:2:4 type B-1 (using 20 mm crushed stone aggregate), 40mm thick, as in floors (laid in alternate panel / bays) finished the surface even and smooth with using extra cement, complete all as specified and directed.

Taking down cement plaster on brick or stone walls or wall tiles etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Rendering 10 mm thick, on fair faces of brick work or concrete surfaces in cement sand mortar 1:6, finished surface even and fair without using extra cement, complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section as in framed work, in any position, complete all as specified and directed.

Excavating in post holes (or similar holes) each not exceeding 0.5cu.m, getting out in soft / loose soil, including returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed.

PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete, including sub bases of floors or similar work, complete all as specified and directed.

Rolled mild steel sections as in Plate girder or single stanchions (ISMB-100), built up of one beam or channel section with flange plates, caps, bases. splices, angle brackets, cleats and other connections conforming to Fe 410-W (Gde- E- 250) quality- A, including welding, cutting, etc, complete all as specified and directed.

Rolled mild steel sections as in Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, complete all as specified and directed.

Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 MPa as in roof covering / cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Framed work such as grills, gratings, etc.. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, and similar work conforming to Fe-290 Gde-E-165, fixed in repairs, complete all as specified and directed.

Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying two coats of white wash, complete all as specified and directed.

Preparation of new steel and iron surfaces over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

Demolition of concrete in ground floors and pavings not exceeding 15cm thickness (below or above ground level), complete all as specified and directed.

Plain cement concrete 1:2:4 type B-1 (using 20 mm crushed stone aggregate), 100mm thick, as in floors (laid in alternate panel / bays) finished the surface even and smooth with using extra cement, complete all as specified and directed.

Plain cement concrete 1:2:4 type B-1 (using 20 mm crushed stone aggregate), 50 mm thick, as in floors (laid in alternate panel / bays) finished the surface fair and even, complete all as specified and directed.

Wearproof topping, 20mm thick, as specified (incorporating an approved metallic floor hardner in ratio 1:4), laid on concrete floors and pavings, and finished even and smooth (except metallic hardner), complete all as specified and directed.

Supply only Metallic floor hardener, complete all as specified and directed.

Excavation in trenches not exceeding 1.5m deep and not exceeding 1.5m wide or area not exceeding 10 sq.m on plan and depth not exceeding 1.5 m for foundation, for shafts, wells, cesspits, manholes, pier holes etc., and getting out in soft / loose soil, complete all as specified and directed.

Steel water tubing, medium grade, ISI marked, galvanised, including short lengths, laid in trenches complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 80mm bore of pipe, complete all as specified and directed. NOTE:- Necessary excavation and earthwork for GI pipe shall be measured and paid separately under respective items of this Schedule.

Sluice valve heavy duty both ends flanged class PN 1.6, ISI marked, with high tensile steel spindle cast iron hand operated wheel and cap, top nuts, bolts and washers including 3mm thick rubber gasket joint and taking out existing sluice valve of any make of 80 mm bore, complete all as specified and directed.

Construction of brick masonary valve pit chamber of size 900 mm x 900 mm x 900 mm (internal dimension) including necessary excavation and earthwork in soft loose soil, foundation bed concrete 150 mm thick PCC 1:4:8 type D-2 (using 40 mm stone aggregate), fly ash brick work in one brick thick wall buildtin cement and sand motar 1:4, 15mm thick rendering in cement and sand mortar 1:4 on internal surface and top of of valve pit upto 200 mm depth externally, PCC 1:3:6 type C1 (20mm graded stone aggregate) as in coping, mild steel sheet cover 3.15mm thick and mild steel sheet fitted in angle iron frame size 40mm x 40mm x 6mm around valve pit, locking arrangement with pad lock of size 50 mm steel 6 leaver with double keys of make ; Godrej / Link or Harrision locks complete including provision of two coats of synthetic enamel paint over one coat of red oxide primer on steel surface,complete all as specified and directed.

Supply, installation, testing and commissioning of submersible pupm set, electric driven, 415 V, 50 Hz, three phase, 20 HP, 15 KW, speed 2900 rpm (sync), delivery size suitable for 150mm NRV, having discharge capacity 870 litres per minute at 75m head, suitable for lowering inside existing casing pipe of bore well (300/350 mm) including necessary jointing to existing MS column pipes with flanged joints, with rubber gaskets, nut, bolts and washers of required size and including electrical connection from starter panel to motor with existing submersible cable, complete all as specified and directed. MAKE:- Model No: BPHA 333/4F+ HBC of KSB or techno-commercially equivalent model in Cromption Greaves/ Calama / Kirloskar NOTE:- (i) Column pipe with flanged joints and submersible cable will be measured and paid separately. (ii) Rates for taking out of old submersible motor pump set and lowering of new motor pump set shall deemed to be included in rates quoted. (iii) Old submersible pump after taking out shall be deposited in AGE E/M old Cantt store yard. (iv) The cost of necessary T&P shall deemed to be included in rates quoted.

Supply, installation, testing and commissioning of submersible pupm set, electric driven, 415 V, 50 Hz, three phase, 30 HP, 22 KW, speed 2900 rpm (sync), delivery size suitable for 150mm NRV, having discharge capacity 1000 litres per minute at 75m head, suitable for lowering inside existing casing pipe of bore well (300/350 mm) including necessary jointing to existing MS column pipes with flanged joints, with rubber gaskets, nut, bolts and washers of required size and including electrical connection from starter panel to motor with existing submersible cable, complete all as specified and directed. MAKE:- Model No: BPHA 333/4C+ HBC of KSB or techno-commercially equivalent model in Cromption Greaves/ Calama / Kirloskar NOTE:- (i) Column pipe with flanged joints and submersible cable will be measured and paid separately. (ii) Rates for taking out of old submersible motor pump set and lowering of new motor pump set shall deemed to be included in rates quoted. (iii) Old submersible pump after taking out shall be deposited in AGE E/M old Cantt store yard. (iv) The cost of necessary T&P shall deemed to be included in rates quoted.

Supply, installation, testing and commissioning of submersible pupm set, electric driven, 415 V, 50 Hz, three phase, 33 HP, 24.5 KW, speed 2900 rpm (sync), delivery size suitable for 150mm NRV, having discharge capacity 1100 litres per minute at 75m head, suitable for lowering inside existing casing pipe of bore well (300/350 mm) including necessary jointing to existing MS column pipes with flanged joints, with rubber gaskets, nut, bolts and washers of required size and including electrical connection from starter panel to motor with existing submersible cable, complete all as specified and directed. MAKE:- Model No: BPHA 3335F+ HBC of KSB or techno-commercially equivalent model in Cromption Greaves / Calama / Kirloskar NOTE:- (i) Column pipe with flanged joints and submersible cable will be measured and paid separately. (ii) Rates for taking out of old submersible motor pump set and lowering of new motor pump set shall deemed to be included in rates quoted. (iii) Old submersible pump after taking out shall be deposited in AGE E/M old Cantt store yard. (iv) The cost of necessary T&P shall deemed to be included in rates quoted.

Supply, installation, testing and commissioning of submersible pupm set, electric driven, 415 V, 50 Hz, three phase, 40 HP, 30 KW, speed 2900 rpm (sync), delivery size suitable for 150mm NRV, having discharge capacity 1200 litres per minute at 75m head, suitable for lowering inside existing casing pipe of bore well (300/350 mm) including necessary jointing to existing MS column pipes with flanged joints, with rubber gaskets, nut, bolts and washers of required size and including electrical connection from starter panel to motor with existing submersible cable, complete all as specified and directed. MAKE:- Model No: BPHA 383/4A+ HBC of KSB or techno-commercially equivalent model in Cromption Greaves/ Calama / Kirloskar NOTE:- (i) Column pipe with flanged joints and submersible cable will be measured and paid separately. (ii) Rates for taking out of old submersible motor pump set and lowering of new motor pump set shall deemed to be included in rates quoted. (iii) Old submersible pump after taking out shall be deposited in AGE E/M old Cantt store yard. (iv) The cost of necessary T&P shall deemed to be included in rates quoted.

Cast Iron fittings for flanged / spigot socketed end pipe upto 150mm bore conforming to IS-1538 such as bends. Tapers. Tee pieces (single & double branch) any type and angle/radius and straight connecting pieces but all ends flanged, complete all as specified and directed. NOTE:- Jointing and Jointing material shall be measured and paid separately under respective items of this Schedule

Rubber or fibre board gaskets for flanged joints including jointing material required suitable for 100 mm bore pipe and fittings in old or new pipe of any locations, complete all as specified and directed.

Rubber or fibre board gaskets for flanged joints including jointing material required suitable for 150 mm bore pipe and fittings in old or new pipe of any locations, complete all as specified and directed.

MS column pipe 100mm dia, thickness 5.4mm, complete all as specified and directed. NOTE:- Column pipe shall be cut off 3 metre length and making thread for the both ends by lathe and fixing the MS flange of size 175mm x 12mm thick duly welded firmly with 90 degree perpendicularly including provision of 4 Nos of bolt and nuts with washers each flange shall deemed to be included in the quoted rates

MS column pipe 125mm dia, thickness 5.4mm, complete all as specified and directed. NOTE:- Column pipe shall be cut off 3 metre length and making thread for the both ends by lathe and fixing the MS flange of size 200mm x 15mm thick duly welded firmly with 90 degree perpendicularly including provision of 8 Nos of bolt and nuts with washers each flange shall deemed to be included in the quoted rates

MS column pipe 150mm dia, thickness 5.4mm, complete all as specified and directed. NOTE:- Column pipe shall be cut off 3 metre length and making thread for the both ends by lathe and fixing the MS flange of size 225mm x 15mm thick duly welded firmly with 90 degree perpendicularly including provision of 8 Nos of bolt and nuts with washers each flange shall deemed to be included in the quoted rates

Industrial cable for submersible pump, PVC insulated, flat three core, 6.00 sq.mm (nominal area) with multi stranded copper conductor, 1100 V grade, conforming to IS-694, connected from starter to pump motor including jointing material, complete all as specified and directed. MAKE:- Havells product code No WHPNDSKB36X0 or techno-commercially equivalent model in Finolex / RR Cable

Industrial cable for submersible pump, PVC insulated, flat three core, 10.00 sq.mm (nominal area) with multi stranded copper conductor, 1100 V grade, conforming to IS-694, connected from starter to pump motor including jointing material, complete all as specified and directed. MAKE:- Havells product code No WHPNDSKB3010 or techno-commercially equivalent model in Finolex / RR Cable

Industrial cable for submersible pump, PVC insulated, flat three core, 16.00 sq.mm (nominal area) with multi stranded copper conductor, 1100 V grade, conforming to IS-694, connected from starter to pump motor including jointing material, complete all as specified and directed. MAKE:- Havells product code No WHPNDSKB3010 or techno-commercially equivalent model in Finolex / RR Cable

Industrial cable for submersible pump, PVC insulated, flat three core, 25.00 sq.mm (nominal area) with multi stranded copper conductor, 1100 V grade, conforming to IS-694, connected from starter to pump motor including jointing material, complete all as specified and directed. MAKE:- Havells product code No WHPNDSKB3010 or techno-commercially equivalent model in Finolex / RR Cable

Submersible pump controller in sheet metal enclosure type suitable for 30 HP or 22.5 kW submersible pumping set relay max range 30-50 Amps, with timer controlled and single phase preventor, complete all as specified and directed. MAKE:- Model No. MU-G 30 FACD, Cat No CS96008COGO of L&T or techno-commercially equivalent model in BCH / Havells

Submersible pump controller in sheet metal enclosure type suitable for 50 HP or 37.5 kW submersible pumping set relay max range 45-75 Amps, with timer controlled and single phase preventor, complete all as specified and directed. MAKE:- Model No. MU-G 50 FACD, Cat No CS96009COJO of L&T or techno-commercially equivalent model in BCH / Havells

M/S DEEKSHA CONSTRUCTION

chauhan construction

Mohit Enterprises

R.K.ASSOCIATES