Provision of Security light and High mast light at Regional Training Center, Jharkhand Home Guard Wind, Chianki, Palamu.

Swaged steel tubular pole ( 410SP-2) of height 7 Mtr. onfirming to IS:2713 (Part II ) in three section with steel base size, bottom of the pole made of 50 mm dia MSB Clamp pipe welded to 300 mm long MS canopy of suitable dia at an angle of 102.5 suitable size of nuts and bolts including rating of one cost steel primer and two coat of read - oxide all complete as required. (Without Arm)

a) Single arm 1 mtr long

b) Double Arm (1x2) mtr long

Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.

a) Above 6.5 metre and upto 8.0 metre

S.I.T.C of floowing rating LED Street lighting luminarie with pressure die cast housing and toughened glass cover (IP 66 protection) in existing pole/pipe for supply voltage 100-270V AC, 50Hz. Luminarie shall be confirm to IS: 10322 part-5/section-3 and shall be complete with all neccssary accessories as required

a) 90W LED Street light

S.I.T.C of floowing rating LED Flood lighting luminarie with pressure die cast housing and toughened glass cover (IP 66 protection) in existing pole/pipe for supply voltage 100-270V AC, 50Hz. Luminarie shall be confirm to IS: 10322 part-5/section-5 and shall be complete with all neccssary accessories as required

a) 120W LED Flood lgiht (On Building)

b) 200 W LED Flood lgiht (for High Mast light)

S.I.T.C of following rating LED Post top lamp made in die cast aluminium housing with decorative clear/opal serylic diffuser on existing pipe including connection with 1.5sq.mm. copper conductor etc all complete as required.

20/25W LED Post top lamp clear

Supplying and drawing following sizes of FR PVC insulated copper conductor single core cable in existing surface / recessed steel / PVC conduit including dismantling as required

a) 3x1.5 sq mm

6 sq mm 2 core (for building light and gate light)

10 sq mm 4 core (for LED Street light)

25 sq mm 3.5 core (from main panel to hight mast)

50 sq mm 3.5 core (from Poel to main Panel)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size not exceeding 35 sq mm directr in ground including excavation, and refilling the trench etc as rquired, but excluding sand cushioning and protective covering.

Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size exceeding 35 sq mm but not exceeding 95 sq mm direct in ground including excavation, and refilling the trench etc as rquired, but excluding sand cushioning and protective covering.

10 sq mm aluminium lugs

16 sq mm alluminium lugs

25 sq mm aluminium lugs

50 sq mm aluminium lugs

Cabel Juction box.

Supplying and fixing 6 amps to 32 amps rating, 240 volts, 10 KA, “B” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, esting and commissioning etc. as required.

6/32 amps, single Pole, "B" series

Supplying and fixing 6 amps to 32 amps rating, 240 volts, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, esting and commissioning etc. as required.

6/32 Amp DP

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

a) 2 way single door

Supplying and fixing of following sizes of PVC/G.I box on surface / recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required.

72 mm x 146mm x 48mm deep/ (4" x 7")

Earthing with copper earth plate 600mm x 600mm x 3mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) as required.

Supply and laying 8 SWG copper wire at 0.50 metre below ground level for conductor earth electrode, including solding etc. as required.

Supply of 16mtr. High mast in two section Construction S355 grade as per BS-EN 10 025 Top Dia 150mm, bottom dia 360mm, plate thickness 3mm, 20side polygon, galvanisation as per BS EN ISO 1461, base plate dia 520mm, base plate thickness 25mm, GI single spike lighting protection, maximum wind speed 47 m/s with 6 nos foundation bolts of PCD 445mm TS 600/ 24mm dia/850 mm long. Luminaries carriage : Material for 40 NB ERW Class B – M.S. Pipe, dia of carriage ring 450mm (ID) with 8/12 arm, welded, 2 sections having carrying capacity upto 8/12 luminaries. Trailing Cable : 5 core 2.5sq.mm. PVC flexible copper conductor Winch/Power Tool : Double drum, SWL 350 kg with 1HP 6 pole single speed integral motor Rope : Grade AISI 304, 7/19 construction, dia 5mm, BLC 1450 x 2 having 2 nos of continues rope. Aviation obstruction light : twin dome aviation obstruction lights LED type as required.

For 16 mtr. High mast : ITC of the high mast and light fixture with the help of suitable tools and plants, wiring of luminaries with all wiring material like PVC insulated PVC sheathed flexible cable of suitable copper conductor lugs, MCB and all labour & construction of shallow foundation with M25 grade concrete for the high mast considering safe soil bearing capacity of 10T/ mtrs sq. for 16 M High mast.

Outdoor stand mounted Feeder Panel with 63amp TP&N, MCB incomer, 65amp TP contactor automatic switching of luminaries, power tool control incommer outgoing terminal etc as reqd. (for high mast)

Fabriaction and installation of cubical panel with following accessoris made of 16 SWG M.S sheet painted with one coat steel primer and two coat power spray painting with apprved shade making PCC plinth and foundation includgin fitting/ fixing/ connection & Transportation upto work site, labour charge etc all complete.

150/160 Amps 35 KA fixed thermal setting (for line incoming)-1 nos

125 Amp MCCB 16 KA fixed thermal setting (for Genrator incoming)-1 Nos

160 Amps 4 Pole chngover- 1 nos

25-100 Amps, 10 KA fixed thermal setting (for outging)-4 Nos

LED Indicator lamp R/Y/B/G- 3 nos

ANALOG Volt mtr (0-500 volt)-1 Nos

ANALOG Amp Mtr (0-500Amp)-1 Nos

C.T Coil of CT rato 200/5 IS:2705 Part 3-3 Nos

25mm x 5mm coppwer strips (1.15kg/Mtr)26 kg

Labour Cess @ 1%

Please Enable Macros to View BoQ information