SPECIAL REPAIR TO SINGLE OFFICERS ACCN AND SERVENT QTR IN KEY LOC PLAN PH-I OF 147 LT AD REGT, PROVN OF ONE TOILET BLOCK NEAR GUN SHED AT 147 LT AD REGT (COMP) AND ADDITION / ALTERNATION TO BUILDING NO P-9C FOR CER-TAIN UNIT UNDER GE DEHU ROAD

M & L for Complete removal of existing treatment of surface finish on wall (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped with wall care putty (2 mm thick) and applying one coat of primer with two coat of oil bound distemper complete all as specified. Note : Putty shall be measured and paid separetely.

M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or Rectangular) area of each tile exc. 0.11 Sqm but not exc. 0.18 sqm, as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile including 15mm thick Screed bed or bedding layer in CM 1:6 for laying floor finishes complete all as specified. complete all as specified and directed.

M & L for glazed coloured ceramic tile in vertical surface 350 x 250 x 7mm/ 450 x 350 x 7mm thk set and jointed in neat cement slurry and pointed in white or coloured cement to match including backing in Cement mortar 1:6 10mm thk

M&L for vitrified coloured tiles 8 to 10 mm th (square/rectangular) polished area of each tile 0.30 sqm but n exc 0.42 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm th screed bed in CM 1:6 complete all as specified and directed.

Returning, filling in soil, including spreading, leveling watering and well ramming in layers not exceeding 25cm all as specified and directed.

Taking down chowkhats or with shutter (without taking off shutter from the frames) & removing from site n. exc. 1.5 Sqm each.

Taking down chowkhats or with shutter (without taking off shutter from the frames) & removing from site exc. 1.5 Sqm but n. exc. 4 Sqm each.

S&F for pressed steel door frames with one or more rebates incl necessary fixing lugs, hinges, lock strike plates of size 125 X 60mm

M&L for plain cement concrete M10(nominal mix) using 20mm nominal size graded stone aggregates in door frame filling complete all as specified

S & F plain framed factory made plain framed panelled shutter (two panel) 35mm thk with lock rail and panel of 9mm B W P comercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS 1003 (Pt-I) kiln seasoned and chemically pressure treated

Dismantling floor hearth or wall tiling incl cement mortar bedding/plaster (but not backing) and removing rubbish off the premises etc complete all as directed.

Supply and fixing three track sliding window including frame with two shutters with 4mm thick tinted / plain glass and one shutter using stainless steel wire cloth 0.36mm nominal dia & 1.18 mm width aperture for mosquito proofing with good quality bearing handle, lock, rubber beading and glazing clips etc; fabricated using following aluminium anodised sections conforming to catalogue of 'JINDAL' or of equivalent make complete all as specified and directed by Engineer-in-Charge. (a) Bottom frame - 20620 (b) Top frame & vertical - 20621 (c) Handle (side) - 20606 (d) Shutter inter lock - 20724 (e) Shutter top & Bottom - 20844 (f) Glazing clips - 19352. (Note:- Cost of Tinted glass & wire cloth shall be included in the quoted rate of the item).

S & F Aluminium powder coted decogrill 7.5mm width and 6mm thk of design DG 102 having weight 3.131kg/Sqm fixed to and including powder coated aluminium U type frame with CP brass/SS screws @ 200 c/c, including cutting the grill to proper opening size for fixing and operation of handle and fixing powder coated aluminium section around the opening all as per requirement and direction of Engr-in-Charge

S & F 4mm thick figured glass pin headed type into aluminum frame in square n exc 0.5mm sqqm in each pan complete

S & F 5.5 mm thick ordinary quality glass aluminum frame in square n exc 0.5mm sqqm in each pan complete

M & L for galvanised mild steel wire cloth 0.63mm nominal dia of wire and avg width of aperture 1.40mm and wixed with tinned tacks or galvanised wire staples

Supply & Fixing PVC door frame (50x47) mm made out of plain colour5 mm thich PVC Sheet reinforced with MS Square Tube, supplying & fixing in opening as per specification & drawing

Factory made solid panel PVC door shutter 30 mm thick ( Style ) consisting of frame made out of MS Tubes for top & bottom rails.MS frame shall be covered with heat moulded plain colour PVC ' C 'Channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC Sheets for top rail , lock rail & bottomrail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC Sheet to be fitted in the MS Frame welded / sealed to stiles & rails with suitable PVC Sheet beading, jointed together with solvent cement,supplying & fixing in the frame at site as per specification & drawing.

S & F aluminium alloy , anodised , sliding door bolt with hasp , staple ( bolt type ) & fixing clips of sheet, cast or extruded section & fixing bolts & sliding bolts of extruded section or cast aluminium alloy & fixed - length of bolt 250 mm

S&F in repairs floor door stopper with overall length of cover plate is 150 mm, of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor.

S & F Butt hinges medium weight cold rolled mild steel 75mm complete

S & F Butt hinges medium weight cold rolled mild steel 100mm complete

S&F 150mm long Mild steel barrel tower bolt, stove enamelled black, with bright bolt and fixed.complete

S&F 150mm long Aluminium handles cast type anodised

Taking down cement plaster on brick / stone walls or concrete surface including raking out joints hacking for key and scrubbing down with water etc. complete all as specified & directed by Engineer-in-Charge.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation .etc in hard/dense soil.

Estimated Rate in Rs. P

Taking down steel window/ventiltors of any size

S & F of 32 mm bore brass chromium plated bottle trap for wash basin with inlet and outlet, screwed for pipe or connection including necessary packing, union and cap complete all as specified and directed.

S&F in repair Vitreous china wash basin white flat back size 550 x 400mm including , waste pipe and plug and porcelain stopper and brackets incl cutting for and pinning in ends of brackets or erecting stand along with 32mm dia CP waste coupling and PVC waste pipe complete all as directed.

BASIC RATE In Figures To be entered by the Bidder Rs. P

S & F of 100 mm bore cast iron ‘P’ or ‘S’ trap complete all as specified and directed.

S&F in repairs 10 ltr capacity PVC valveless, syphonic action type flushing cistern low level white with inlet ball valve float and handle including bracket

S & F in repairs Brass cromium plated shower rose of 125 mm dia complete all as specified.

S&F in repair stop/ angle valves cast copper alloy,fancy type chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or union fixed for 15 mm dia GI pipe.

S&F in repairs bib taps cast copper alloy fancy type chromium platted with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass furrule and fixed for 15mm dia pipe.

S & F in repairs pillar mixer for mixing hot and cold water fancy type cromium plated with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed for 15 mm dia pipe.

S & F in repairs 15 mm dia stop valves concelaed type cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or union fixed in repair for 15 mm dia GI pipe all as specified and as directed.

S & F 15 mm dia Stop/angle valves, fancy type, chromium plated with , screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. (CAT No KUP-35053PM)

Taking up or down steel tubes and connections of 15mm dia bore of pipe

All as per item No. 42 above but bore of pipe 20mm

M&L GI tubes, medium grade with all fittings and fixed complete to walls, ceiling or laid in floors, bore of pipe 15mm

M&L for cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

M&L GI tubes, medium grade with all fittings and fixed complete to walls, ceiling or laid in floors, bore of pipe 20mm

TOTAL AMOUNT Without Taxes in Rs. P

S & F PVC Connection 15mm size with PTMT Nuts of length 450mm complete all as specified and as directed.

M & L for taking out old water proofing treatment to RCC roof slab as specified below and as directed by Engineer-in-Charge (a) The roof surface shall be thoroughly wire brushed, washed, dried up & cleaned to remove all foreign materials & dust to receive primer. (b) On the dried roof surface, apply one coat of bituminous primer @ 100 Gm/ Sqm as per manufacturers instruction. (c) On this primed surface, the approved APP modified bituminous membrane with non woven polyester mat asreinforcement weighing not less than 3.5 Kg/ Sqm laid by torch application metho and top surface shall be applied with bituminous aluminium paint. (d) The overlap while torching shall be 75mm on longitudinal direction & 100mm on transverse direction. Note:-Obtain material through out low laying Area

Supply only Liquid water proofing compound .

Material and labour for complete removal of existing treatment of plastered or unplastered old decorated surface walls by brooming down and applying two coats of weather proof paint on external surfaces including a coat of acrylic based primer at any height of building / tower complete all as specified and as directed by Engineer-in-Charge.

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

S & F in repairs ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe of 20 mm bore and fixed (minimum weight 210 gms ) complete all as specified and as directed.

Demolition brick or stone masonary built in cement mortar including all quoins arches pillars etc but excluding ashlars facing dressed stone work and precast concrete block, complete all as specified

M&L for brick work with sub class 'B' brick in cement mortar 1:6, straight or curved on plan exc 6 m mean radius, complete all as specified

M & L for Brick work with sub class B brick straight or curved on plan to any radius in half brick in CM 1:6 complete

Dismantling / taking down AC/PVC waste/vent pipes fixed to walls with all fittings/ accessories any dia pipes all as specified and directed by Engineer-in-Charge.

S&F, PVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls, or laid in trenches bore of pipe 110 mm dia complete all as specified and directed by Engineer-in-Charge.

S&F, PVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls, or laid in trenches bore of pipe 75 mm dia complete all as specified and directed by Engineer-in-Charge.

S&F,110 mm dia PVC (SWR) bends, any radius with access door complete all as specified and directed by Engineer-in-Charge.

S&F,75 mm dia PVC (SWR) bends, any radius with access door complete all as specified and directed by Engineer-in-Charge.

S&F, 75 mm dia PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge.

S & F in repair PVC (SWR) floor trap plain with grating including grating jointing with solvent cement 75mm

M&L for Marble work green marble 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in CM (1:4) including pointing in white cement (1:2) including rounding edge using marble dust with admixture of pigment to match with green marble shade complete all as specified.

Demolition of concrete ( un reinforced ) in ground floors and paving n.exc 15 cm thk (below or above ground level) complete all as specified and directed.

M & L for cement concrete Type C2 1:3:6 (using 40mm graded aggregates) as in plinth protection 75 mm thick finished top surface even and smooth without using extra cement complete all as specified and as directed.

S&F in repair 20 mm dia anodised aluminium alloy curtian rod fixing in any opening including stainless steel brackets 02 Nos bracket in each door/windows with side knob as specified and directed complete .

S & F in repair liquid soap containedr of PTMT fixed with and incl CP brass screws and wooden/plastic cleats

S & F in repair Towel ring of PTMT fixed with and incl CP brass screws and wooden/plastic cleats

S & F in repair Towel rail 600mm long of PTMT fixed with and incl CP brass screws and wooden/plastic cleats

S & F factory made 35 mm thick glazed & skeleton shutter of 2nd class hard wood open rebated and prepared to receive gauge (divided into squares with sash bars) edges of framing plain chamfered or rounded, fitted without & fitted beads for securing glass etc, sizes of members of shutters as specified in SSR Pt-I Sec-8 clause 8.23 (a) and fitted to chowkhats complete all as specified.

M&L for rendering 10 mm thick (internal plaster) on fair faces of brick work or concrete surfaces finished even and smooth in cement mortar 1:6, complete all as specified

M&L rendering 15mm thick (external plaster) on fair faces of brick work or concrete surface in CM 1:4 finished even & smooth without using extra cement including WPC complete all as specified & directed by Engineer-in-Charge.

S & F in repairs rotational moulded polyethylene double layer water tanks (vertical cylindrical with close top) as per IS 12701: 1996 of 500 litres capacity hoisted and fixed in position including provision of 20 mm /15 mm dia medium grade GI pipe spouts for connecting inlet, outlet, over flow and washout pipes including dismantling all as specified and as directed complete all as specified and as directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. all as specified and directed.

S&F in repair vitreous china squatting pan ORRISA PATTERN size 580x440mm white with integral foot rests excluding flushing cistem & fush pipe fixed in repairs complete all as specified and as directed. .

M & L for two coats of synthetic enamel paint over new wooden surfaces of any description not otherwise described over 10cm in width or grith over one coat of pink primer including preparation of surfaces complete.

M & L for Preparing old painted surfaces of wood and wood based materials of any description over 10 cm in width or girth and applying two coat of synthetic enamel paint of tint approved by Engr-in-charge complete all as specified.

M & L for Preparing old painted steel & iron surfaces of any description over 10 cm in width or girth ,including roof and applying two coat of synthetic enamel paint of tint approved by Engr-in-charge complete all as specified.

Dismantling wall/ ceiling boards(fibre pulp insulation etc.) or insulations boards /slabs/blankets any thickness incl. cover fillets and alum snip grid.

M&L for false ceiling with 10mm thick of panel size 600mm x 900mm plaster of paris sheets fixed with machine screws on GI channel 18 gauge thick, grid work main joists placed at 750mm centres, secondary joists placed at 450mm centres, GI angle suspenders from roof and treating the plaster of paris sheets with thin layer of pop with Gypsum binder, sanding the surfaces till smooth surface is obtained including preparation of surface and applying two coats of oil bound distemper over a coat of primer all as specified and as directed.Make: Gyproc or Equivalent

M&L12 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber/ RCC frame work complete

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flap 30 mm

supply and fix 32 mm dia flexible waste pipe for wash basin and kitchen sink complete all as specified and directed.

S&F in repair Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 mtr long flexible tube and ABS wall hook including making connection and fixed in position complete all as specified and as directed by Engineer-in-Charge

S&F in rep Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long all as specified and directed.

M&L prep of old decorative surface by Washing, rubbing down and stopping of distempered and painted surfaces of ceiling, and applying two coats of oil bound distemper paint including 2 mm thick wall care putty (wherever required) on plastered surface complete all as specified & directed by Engineer-in-Charge. (NOTE: Putty shall be measured and paid separately)

M & L for applying a layer of 2 mm thick Birla white putty/JK white wall care putty on wall / ceiling surfaces including removal of existing treatment and making the surface uniform and smooth complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light/exhaust fan) complete,(fittings such as switches, ceiling roses,pendants etc. to be measured separately), removing materials to store for keeping in safe custody for reuse at site and making good disturbed surfaces of walls, floors, etc.

Taking down unserviceable main switches,DBs alongwith teak wood boards etc and making good disturbed surfaces of walls/ floors to match the existing surfaces all as specified.

M&L for Point wiring complete with 1.5 Sqmm single core PVC insulated but unsheathed copper conductor FRLSH cable 1100 V grade drawn through concealed PVC conduit of suitable size as per site requirement including tees, junctions etc fixed on wall/ floor/ ceiling etc including 1.5 Sqmm PVC insulated but unsheathed multistranded copper conductor FRLS cable as earth continuity wire complete ISI marked for suitable size excluding modular flush box, cover plate all accessories and making good the disturbed surfaces of wall by cement work after cutting and conduiting into the wall all and matching the surface to the existing finishing colour all as specified & directed.

One bell/ buzzer point controlled by one push button on the same board with other switches or independent with cables1.5 sq.mm. size

One 3 pin socket outlet, 15 Amps, independent, with cables 4 sq. mm size

One light point controlled by one one way switch

Supply & Fix of Arteor modular mirror/graphic/wood/leather type, white/black/gold/metal finish color switch 1 way, 6 Amps, 1 modue complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & Fix of Arteor modular mirror/graphic/wood/leather type, white/black/gold/metal finish color switch 1 way, 16 Amps, 1 modue complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & Fix of Arteor modular mirror/graphic/wood/ leather type, white/black/gold/metal finish color Bell push switch 1 way, 6 Amps, 1 modue complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & Fix of Arteor modular mirror/graphic/wood/ leather type, white/black/gold/metal finish color socket 5 pin 6 Amps, 2 modue complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & Fix of Arteor modular mirror/graphic/wood/ leather type, white/black/gold/metal finish color socket 5 pin 6/16 Amps, combination type 2 modue complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & Fix of Arteor modular mirror/graphic/wood/ leather type, white/black/gold/metal fi

nish color Fan regulator 120 Watt 2 module complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & Fix of Arteor modular mirror/graphic/wood/ leather type, white/black/gold/metal finish color cover plate frame, 4 module complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & Fix of Arteor modular mirror/graphic/wood/ leather type, white/black/gold/metal finish color cover plate frame, 6 module complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & Fix of Arteor modular mirror/graphic/wood/ leather type, white/black/gold/metal finish color cover plate frame, 8 module complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & fix of metal flush boxes mounting 4 module, made of MS chromium plated complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & fix of metal flush boxes mounting 6/8 module, made of MS chromium plated complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm Make : Turbo-Force Havells/Crompton/Bajaj/Polycab

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete

One ceiling/exhaust fan point controlled by one one way switch

One switch socket 5 pin 5 Amps flush type on same board.

One switch socket 5 pin 5 Amps flush type on Ind board.

Supply and fixing round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete

Taking down unserviceable Meter box including all fittings and fixture complete, Supply and installed meter box made with 2 mm thick MS sheet powder coated of suitable size for fixing electric meter 07 Nos and one MCCB 63 Amps TPN as incommer, Seven number out going MCB SPN 40 Amps , IP-65 fitted with 04 no copper strip of size 30x6mm included necessary connection arrangement with suitable size of copper flexible cable from MCCB to Busbar and Busbar to MCB, Meter complete all as directed. Make : CPRI approved. Note : Cost included the MCCB, MCB, Busbar and other accessories which is required for necessary connection (lugs etc). Cost of meter will be paid separately.

Supply and fix electronic meters temper proof LCD display with polycarbonate cover 230 V, 10- 60Amp, single phase accuracy class-I 50Hz, conforming to IS 13779, IP-54, with parameters to show data, time, current reading, load, PF, voltage and KWH

Supply and fix LED security/ street light 35 W IP 65 Die cast Aluminium extruded housing with reflector and enclosed with toughened glass IP 65 for 1Wx15/18 Nos LEDs and Driver incl pipe & clamps all as specified & Directed. Make :- HPL or equivalent in Luker/ Bajaj/ Philips/ Havells

Each Job

Returning,filling in including spreading ,leveling ,waterring and well ramming in layers not exc 25cm with excaveted soil as directed.

Removing excavation material/soil n .exc. 250 m and not exc 500m and depositing where directed at a level n. exc 1.5 m above the starting point.

M&L moorum filling in floors/pavings, laid in layers not exceeding 15cm thick, spread levelled and rammed/rolled including watering to reqd level and gradient all as specified.

S&F submain wiring with 2 single core PVC insulated multistranded flexible copper conductor 1100 Volts grade cables 6 Sqmm and 1 run 6 Sq mm Earth Wire PVC insulated multistrand cupper conductor cable (FRLSH) drawn through concealed PVC conduit of suitable size and with all accessories all as directed and specified by Engr-In-charge.

M & L in repair MCB DB SPN sheet metal double door enclosure mounted into the wall of suitable size for mounting MCB 230 Volts , 4 way

S & F MCB SPN 40 amps, 240Volts 10KA

S & F MCB SP 5-40 amps, 240Volts 10KA

M & L for providing reinforced cement concrete M-25 (Design Mix), using 20 mm graded stone aggregate as in foundation including rafts, footing, foundation beams, plinth beams, base of columns and the like complete all as specified and directed.

M&L for Cement concrete, (1:4:8) type D2 (using 40mm graded aggregate) for PCC as in foundations/filling mass concrete, flooring etc complete all as specified and directed

Supply & fix in replacement of Modular USB socket of 2 module complete with input 250V & output is 12/24 V DC with two USB cord arrangement complete all as specified. Make: Standard/ Legrand/ Indoasian

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for providing reinforced cement concrete M-25 (Design Mix), using 20 mm graded stone aggregate as in columns, pillars, piers, posts and struts and the like complete all as specified and directed.

M & L for providing reinforced cement concrete M-25 (Design Mix), using 20 mm graded stone aggregate as in roof Beam, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M & L for providing reinforced cement concrete M-25 (Design Mix), using 20 mm graded stone aggregate as in slabs complete all as specified and directed.

M & L for providing reinforced cement concrete M-25 (Design Mix), using 20 mm graded stone aggregate as in chajjas and the like complete all as specified and directed.

M & L for use and waste of form work to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beam and similar works in rough finished flat surface of concrete complete all as specified and directed.

M & L for hard core of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified and directed.

M&L Formwork to sides of Square, rectangular on plan or polygnal pillars, posts, struts, piers, columns and stanchion rough finished flat surface of concrete complete all as specified and directed.

M&L Formwork for rough finished surface to sides and soffits of beam, bressummers,lintels, cantilevers and supports etc all as specified and directed.

M&L for rendering 05 mm thick on ceiling in CM 1:3 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

M & L for use and waste of form work rough finished surface of concrete flat to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exc. 200 mm thick horizontal or slopping in rough finished surface of concrete complete all as specified and directed.

M & L non skid coloured ceramic tiles 7 to 8 mm thick area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm , in floors, etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match. Including 15 mm thick screed bed or bedding layer in cement mortar 1:6 complete.

M & L 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms wash Basin top and like in cement mortar (1:4) including rounding edges of sides, pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite complete.

M & L for use and waste of form work to chullah hoods, chajjas, troughs and similar items including edges in rough finished surface of concrete complete all as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts and 45 cm long

Supply and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame., complete as specified by the manufacturer and as per directions of Engineer-in-charge

M&L for three coats of white wash on new plaster surfaces but in ceilings including preparation of surface over a coat of primer complete all as specified and directed

Supply and fixing to existing door frames 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete as specified by the manufacturer and as per directions of Engineer- in-charge.

S&F 4 mm Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete

M&L for concrete bed to drain pipe 150 mm dia including packing under and haunching against the side of pipes after they are laid and tested complete all as specified and directed

M&L for reinforced cement concrete pipes class NP-2 , laid in trenches & jointed complete with collars, dia of pipe 150 mm complete all as specified and directed by Engineer-in-Charge.

M/L for water proofing treatment using polymerised membranne to roof slab including 10 mm thick plaster in cement mortar 1:4 as in roof mixing with WPC mixing with water proofing compound by 3% by weight of cement or as per manufacture instruction (a) Apply one coat of oil bituminous primer @ 0.20 kg/Sqm over concrete surface. (b) Laying APP Polimerised modfied membrane not less than 3 mm thick and weighing not less than 3.5 kg per Sqm

by torch applicaton method. (c) The overlap for APP membrane shall be 75 mm on longitudinal direction and 100 mm on transverse direction. (d) Finally applying a coat of solar reflective bituminious aluminium paint @ 0.15 Kg/Sqm over the membrane. (e) The make / treatment shall be from the one of the following manufacturer:- (i) 'Moply FP' of M/s Texsa (I) Pvt Ltd. (ii) 'Hyperplast' pf IWL India Ltd. (iii) 'Super thermpay' manufactured by M/s Shalimar tar product. (iv) 'Hydroflame' of M/s Hydrotech Ltd.

M&L for preparation of new plastered surface of wall and applying three coat of white wash over a coat of primer complete all as specified and directed

Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out in hard dense soil all as specified

M & L for 75 mm thick PCC type D-2 1:4:8 (40 mm graded aggregate) as in sub base for tiling complete all as specified and as directed

Excavation over areas 1.50m in depth for foundation etc or for shaft, wells, cesspits, manholes , pier holes etc n exc 10 Sqm on plan and n exc 1.50 m in depth and getting out in average soil.

Excavation over areas for depth beyond 1.50 mtr in hard dense soil and getting out

Loose filling with broken bricks aggregates of gauge 80 to 150 mm in sockage wells

S&F RCC Hume pipe 900mm dai and 2.50 Mtr length septic tank tank capacity 1800 Ltr for 25 users including excavation earth work as reqd, and connected to soak pit as specified and directed.

M & L for PCC type D-2 1:4:8 using 40mm gradded crushed stone aggregate as sub base of floor 100mm thk

M & L for PCC type B-1 1:2:4 using 20mm gradded crushed stone aggregate as sub base of floor 25mm thk

M & L for reinforced cement concrete in foundation, including rafts footings foundation beams; plinth beams; bands, bases for columns etc. type B1 1:2:4 nominal mix using 20mm gradded crushed stone aggregate

S&F aluminum powder coated ventilator with three shutter - one glazed shutter fixed in half bottom and two upper shutter one glazed outside openable and other wire guaged inside openable shutter with frame with or without sash bars of aluminum section weighing 0.55 Kg per Sqm including necessary joining clits , glazing clips, rubber packing, alu. Snap beading , screws, aluminum fittings, suitable handles and wire mesh complete .

M & L for Preparation of newly plastered surfaces of wall and appling two coats of oil bound distemper on walls over a coat of primer on plastered surfaces complete including 3mm thick wall care putty complete all as specified and as directed.

S & F 12mm thick Gypsum board for ceiling, insulation and accoustic purpose 60x60cm in size fixed with screws with staples incl aluminium snap grid frame work 605x605 mm in flat/slopting ceiling with aluminium anodised grid work 35.60x23.60x1.60mm main Tee 23.60x23.60x1.60mm cross section and 26x26x1.60mm angle including 3mm dia GI wire suspender of suitable length aluminium cleats etc complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling and applying two coats of distemper oil emulsion over and including a coat of priming complete all as specified and as directed.

Supply ad laying concelled of CPVC pipes SDR 11 & plain CPVC SDR 11 fitting or laying walls or in floors complete all as specified 16mm

S&F rolled sections as in main and cross beams, hip and jack rafters,purlins where connected to common rafters confirming to Fe 410 -W (Gde- E- 250) quality- A complete all as specified & directed by Engr-in-charge.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as per manufacturers instructions with all fittings and accessories complete all as specified & directed by Engr-in-charge.

M & L for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area

M & L for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured)

M & L fo treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface

M & L for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area

S&F 15 mm dia bib taps two way fancy type cast copper alloy screwed down, screwed for iron pipe or for brass furrule and fixed for 15mm dia pipe complete all as specified and as directed. (CAT No KUP-35041PM) from Jaguar

S&F 15 mm dia single lever basin mixer with popup waste pipe with 450mm long braided hose chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed pipe complete all as specified and as directed. (Cat Part No : KUP-35011BMP Jaguar)

S&F vitreous china wash hand basin, off white Counter top of size 545 x 545 x180mm incl waste coupling, pipe excluding taps and connection all as specified and directed by Engineer-in-Charge (Cat No FSS-WHT-29601 Jaguar)

S&F in repair Health faucet Brass body chromium plated suitable for 15mm dia pipe with 1.00 mtr long flexible tube and ABS wall hook including making connection and fixed in position complete all as specified and as directed by Engineer-in-Charge (Cat No CPHF-1) from Prayag

Supply and fix single lever3-inlet diverter exposed parts kit consisting of operation lever,cartridge sleeve, wall flange woth seals button allembly sleeve and buton cap including concealed body for 3 inlet single lever diverter with button assembly etc complete all as specified and as directed. (CAT No : OPP-15125PM for external body and ALD-193N for conceled body) from Jaguar

S&F Hand shower 140mm round shape single flow with air efect (ABS body and face plate cromium plated) with rabit cleaning system including CP flexible pipe 1.25m long all as directed. CAT NO HSH-1721 from Jaguar

S&F Over head shower 140mm round shape multi flow with air efect (ABS body chromium plated with grey face plate) with rabit cleaning system all as directed. (CAT NO OSH-1769) from Jaguar

S & F Mirror Cabiet of size 622mmx422mm (CAT No PTA-50) from Prayag

Supply ad fix brass Towel rack CAT NO CPA-12 from Prayag

S & F single piece water closet with UF soft close seat cover, hinges, dual flush cistern fitting including all fixing accessories set of size 395mmx740mmx730mm `S' trap of size 300mm (Cat No VGS-WHT-81851S300UF)

S & F Brass CP bottle traps for wash basin with inlet ad out let screwed for pipe or connections including necessary packing 32m

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F Sheet glass, 5.5 mm thk ordinary quality, in square exc 0.5

sq. m in each pane complete. all as specified and directed by Engr-in-Charge.

Taking down carefully by old/ damaged/unserviceable unscrewing from boards/outlets boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and regulators etc complete all as specified.

Taking down carefully fan any type complete deposited in MES E/M store complete all as specified.

Material and labour for Sub-main wiring complete with 4 sqmm single core PVC insulated but unsheathed multistranded copper conductor cable 1100 V grade drawn through concealed PVC conduit with wall thickness not less than 1.8 mm incl sunken type pressed steel terminal boxes including 4 sqmm single core PVC insulated but unsheathed copper conductor grade 1100 V grade cable as earth continuity wire complete all as specified. (two run 6 sqmm and one run 4 sqmm) (Make : Finolex/Anchor/Polycab)

Supply & Fixing of BLDC Ceiling fan of 1200 mm sweep 3 blade in white/ brown/ Ivory clolor with regulators, with down rod AC single phase, 230 V, 50 Hz, 5 star rating including provision of cable from ceiling rose or connector to ceiling fan complete all as specified. Make: Havells cat pat No. ES 5 or equivalent in Bajaj/ CG/ Polycab Note : Old Fan to be deposited in MES store.

Supply & Fix of Arteor modular mirror/graphic/wood/leather type, white/black/gold/metal finish color switch 1 way, 6 Amps, 1 modue complete all as specified.

Supply & Fix of Arteor modular mirror/graphic/wood/leather type, white/black/gold/metal finish color switch 1 way, 16 Amps, 1 modue complete all as specified.

Supply and fix in repairs for vitreous china EWC of white colour with plastic water closet seat closed pattern with flat bottom (with MS or CP hinging device) and fixing bolts, including connection to drain or out going pipe and to PVC flusing pipe, antisyphonage pipe and all necessary fittings etc complete all as specified and as directed.

Modular switch 2 way 6A, 1 module

Supply & Fix of Arteor modular mirror/graphic/wood/ leather type, white/black/gold/metal finish color cover plate frame, 2 module complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & fix of metal flush boxes mounting 2 module, made of MS chromium plated complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

S&F grating round 100 mm size of PTMT with hole or without hole (Minimum weight 25gms.) complete all as specified and as directed.

S & F of 8 way SPN DB made of CRCA sheet, RAL 9003, powder coated for IK-09 double door, IP-43 glazed door, confirms to IS-8623-1, IEC 61439-1&3, 415 v with 200 amps rated bus bar , ready to use DB insulated phase busbar, neutral bar's with shroud's, earth bar, sticking saddles, cement spill protector, color coded interconnecting wire set, cable ties, blanking plates & circuit identification label with provision for FP, MCB/ Isolator/RCCB/RCBO as incomer & SPN MCB's as outgoing all as specified Make: L&T cat pat No. DBTPE004GD or equivalent in Legrand/ Schneider/ ABB

Supply & fixing in replacement of MCB TPN (3P+N), 415 Volts, 50HZ, 10KA Brecking capacity, C/D characteristics of capacity 63 Amp complete all as specified .

Supply, install, testing & commissioning of Storage type water geyser, electric driven (single phase), capacity 25 Litres, BEE 5 star rated vertical/ horizantal type, Rust proof body, including PTMT pipe for Cold & HOT water from ball valve to inlet & oulet of geyser respectively complete all as specified & directed by Engr-in-charge. Make :- Havells Puro+/ Kenstar Aquaplsh/ Recold Eterno

Supply & fixing in replacement of old ceiling light fitting with new LED tube light POLYCARBONATE FIXTURE in two optional hanging with ceiling including hanging arrangement and also incl. accessories, high power low heating superflux LEDs, 100 lumen/ watt, 120-270 V AC inbuilt electronic driver, complete all as specified for 9/10 watts LEDs. Make : HPL Cat Pat No NEPTUNE 9W or equivalent in Polycab/ Halonix/ Bajaj/ Philips/ Luker

Supply & fixing in replacement of LED bulb 9W. Make : Havells/Shakti/Benlo

M & L for Modular Bell, Ding Dong AC. 230 volts, single pole fitting complete. Make- Legrand/ Standard/ Indoasian

M & L 3 terminals Ceiling rose, AC, 230 V, PVC/ polycarbonatecomplete all as specified. Make- Anchor Penta / Cona/ C&S

M & L for High density ERW PIPE of pressure rating 6 kgf/cm2 fixed/ laid in complete to walls, ceilings or in floors, trenches etc. for cable protection of the following outer dia :-

50 mm dia

Supply & fixing in replacement of LEDs Decorative wall mounted dia-cast Al. LED fixture with ivory/white/Gold coating for up-down accent lighting in the module of Xing Hexa/ Penta/ Round/ Square/OVAL of capacity 14/18 Watts complete high power low heating superflux LEDs, 100 lumen/ watt, 120-270 V AC inbuilt electronic driver all as specified.

Supply & fixing in replacement of LED BED Lamp fitting POLYCARBONATE FIXTURE in two optional hanging with ceiling including hanging arrangement and also incl. accessories, high power low heating superflux LEDs, 100 lumen/ watt, 120-270 V AC inbuilt electronic driver, complete all as specified for 12 watts LEDs. Make : Bajaj Cat Pat No. ALPHA 12W WW or equivalent in Luker/ Philips/ Halonix/ HPL

S & Laying in repair/ replacement cable XLPE insulated screened PVC bedded ,galvanized steel strip or wire armoured ,electric power cable heavy duty 1100 volts grade with strandad aluminum conducter of following sizes:-

25 Sqmm x 3.5 Core

All as per item No 4 above but on skirting over 8 to 10 mm th rendering in CM 1:4 complete all as specified and directed.

All as per Item No 128 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth and getting out all as specified and directed :-