Renovation Modification of Re-Recording Studio for setting up of 100 seat capacity screening hall at Jyoti Chitraban

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:3 (1 cement :3 coarse sand)

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm

Providing and fixing bright finished brass door latch with necessary screws etc. complete : 300x16x5 mm

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing bright finished brass handles with screws etc. complete: 125 mm

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., omplete. Size of Tile 600x600 mm

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gm/ m² sqm

Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 0.63 mm thick with zinc coating not less than 275 gm/m²

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below

Of area beyond 3 sq. metres

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board sqm 1300.50

Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595mm, having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity <0.043 W/m K as per ASTM 518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 50mm wide (90 metre )roll and two coats of primer suitable for panelling as per manufacturer's specification as per direction of Engineer-in-Charge all complete. With 15 mm thick fully perforated square/butt edge light weight calcium silicate panels/ tiles

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.)

Supply and installation of Acoustic Grade Fire Retardant Fabric to be installed on the existing Acoustic Panels by using PVC Grippers

Supply and Installation of Push Back Chairs: Seat (civil) Inner Frame Injection moulded PPCP. Fabric 100% Polyester Fabric Fire Retardant Fabric, Push Back System Heavy Gauge Steel Roller and Spring Push Back Movement. Paint Epoxy Powder Coated Paint (Make Rana Chairs)

Providing making and finishing of 70.5 mm thick full ved Ana height, laminated partition/wall panelling, to be By the made with 50mm x 50mm sal wood frame structure CE(B) for 600mm c/c in bothways and fixing of 19 mm thick greenply plywood on over salwood frame structure and fixed supported from existing rcc slab with fixed, pasting and finishing of 1.5 mm thick decorative laminated sheet on over existing ply surface in both side as per required shade of the laminated sheet the work complete with all necessary hardware materials. like, fevicol, nails, screws,abro tape.etc. and making labour as per directed by the concerned department.

Providing supplying and fixing floor carpet tiles of size Ana 500 mm x 500 mm (admiral make Vista) as directed by the concerned department

Supply, Installation, Testing and Commissioning of Professional 3 Way Main Cinema Screen Speaker. SYSTEM TYPE: 3- way screen, FREQUENCY RANGE (-10 dB): 50 Hz-18 kHz, SYSTEM IMPEDANCE: Passive: 40, LF: 40, M/HF: 40, CROSSOVER: Bi-amp (MF/HF + LF), full passive, SYSTEM POWER: Passive: 800W, Bi-amp: LF 800W, HF 160W, SENSITIVITY (4 PI): 100 dB, MAX PEAK SPL (2 PI): 138 dB (Make:-JBL)

Supply, Installation, Testing and Commissioning of Two-channel, 1350W Power Amplifier. Frequency Response:- 20 Hz-20 kHz, +0/-1 dB (at 1 watt), THD:- <0.5%, 20 Hz-20 kHz, intermodulation Distortion =/<0.35% (60 Hz and 7 kHz at 4:1 from full rated ouput to -30 dB), Slew Rate >10V/us, Voltage Gain 36 dB, Damping Factor (8 ohms, 10 Hz to 400 Hz) >200, Signal To Noise Ratio (A-weighted) >100 dB (Make:- Crown)

Supply, Installation, Testing and Commissioning of Professional High Power Cinema Subwoofer. Frequency Response (±3 dB): 35 Hz 100 Hz, Frequency Range (- 10dB): 30 Hz-500 Hz, Power Handling (2Hr AES Rating): 1600 W, Sensitivity:- 98 dB, Maximum SPL (1m): 139 dB, Nominal Impedance: 2 x 80 (Make:- JBL)

Supply, Installation, Testing and Commissioning of Two-channel, 2100W @ 40 Power Amplifier. Sensitivity: 1.4V, Rated Power Output (per channel):- 3000W 20, 2100W 40, 1200W 80, Signal to Noise Ratio (below rated 1 kHz power at 8 ohms): 103 dB (A-weighted), THD < 0.5%, Frequency Response (at 1W, 20 Hz - 20 kHz): + 0 dB, 1 dB, Crosstalk (below rated power): 20 Hz to 1 kHz >70 dB (Make:- Crown)

Supply, Installation, Testing and Commissioning of Compact Cinema Surround Speaker. Frequency Range (+3 dB):- 65 Hz-18 kHz, Frequency Range (- 10dB): 50 Hz-20 kHz, Power Rating:- 150 watts continuouspink noise600 watts peak, Sensitivity:- 94 dB-SPL half-space/wall- mounted91 dB-SPL free-field, Maximum SPL (1m): 116dB, Nominal Impedance:- 180 (Make:- JBL)

Supply, Installation, Testing and Commissioning of Two-channel, 1350W Power Amplifier. Frequency Response: 20 Hz-20 kHz, +0/-1 dB (at 1 watt), THD:- <0.5%, 20 Hz-20 kHz, Intermodulation Distortion =/<0.35% (60 Hz and 7 kHz at 4:1 from full rated ouput to -30 dB), Slew Rate >10V/us, Voltage Gain 36 dB, Damping Factor (8 ohms, 10 Hz to 400 Hz) >200, Signal To Noise Ratio (A-weighted) >100 dB (Make:- Crown)

Supply, Installation, Testing and Commissioning of Two-channel, 750W @ 40 Power Amplifier. Frequency Response:- 20 Hz-20 kHz, +0/-1 dB (at 1 watt), THD:- <0.5%, 20 Hz - 20 kHz, Intermodulation Distortion:=/ <0.35% (60 Hz and 7 kHz at 4:1 from full rated ouput to-30 dB), Slew Rate: >10V/us, Voltage Gain:- 33 dB, Damping Factor (8 ohms, 10 Hz to 400 Hz):- >200, Signal To Noise Ratio (A-weighted):- >100 dB (Make:- Crown)

Supply and Installation of customized 8 bracket for surround speakers (Make:- Custom)

Supply, Installation, Testing and Commissioning Digital Cinema AV Processor. Upgradeable to full Dolby Atmos capability (with CP950-UPG hardware upgrade kit and Full Dolby Atmos License), Built-in booth monitor to simplify operations and audio quality assurance, Touchscreen front panel interface for easy control, Easily integrates with Dolby Multichannel Amplifier, Web user interface for remote configuration and control, Dolby Atmos Designer compatibility for setup and precise system calibration, (Make:- Dolby)

Supply, Installation, Testing and Commissioning of Wireless Handheld Microphone for Vocal (Make:- AKG/ Sennheiser/ Audio Technica)

Supply, Installation, Testing and Commissioning of 8 Ch Analogue Mixing Console with in-built effect processor. (Make:- Soundcraft/ Behringer/ Allen & Heath)

Supply and Laying of Audio Signal Cable; Balanced microphone cable with single shield, high flexible, velvet faint PVC-Jacket, Conductor: Stranded bare copper wires 28 x 0.10 mm (0.22mm²), Jacket: PVC, 6.0 mm max. Ø (Make:- Gotham/Klotz/ Belden)

Supply and Laying of High flexible Speaker cable for power amplifiers upto minimum 500 Watt (Make Gotham/ Klotz/ Belden)

Supply and Laying of High flexible Speaker cable for power amplifiers upto minimum 4000 Watt (Make Gotham/ Klotz/ Belden)

Supply, Installation, Testing and Commissioning of 24U Floor Mounted Equipment Rack with accessories (Make:- Nettrack/ Valrack/ LinkEu)

Supply and Installation of COB LED 22W Auditorium Hall Round Lights 4000K.

Supply and installation of LED Strip Lights with Profile

Supply and Laying of Electrical Cables Including PVC Conduits and electrical switches, sockets, MCB, DP etc.

Supply and Installation of 2Watt LED Step Lights

HRISHIKESH BAIDSHYA