Construction of School Building Masat, Dadra and Nagar Haveli

Amount

EXCAVATION upto 1.50 Metre for foundation such as footing, pedestals, walls, drains, columns, ramps, plinth beams, cable trenches in dense or Hard soil MECHANICALLY but other than hard rock including shoring, strutting, sorting out and stacking useful material, dewatering where required, cutting vegetation up to 1.5m ht if required and disposing off the excavated stuff upto all lead and lift. Note- All types of soil that can be removed by JCB/ Poclain bucket shall be classified under this item.

EXCAVATION 1.50 to 3.00 Metre for foundation such as footing, pedestals, walls, drains, columns, ramps, plinth beams, cable trenches in Hard Murrum MECHANICALLY but other than hard rock including shoring, strutting, sorting out and stacking useful material, dewatering where required, and disposing off the excavated stuff upto all lead and lift.

EXCAVATION 1.50 to 3.00 Metre for foundation such as footing, pedestals, walls, drains, columns, ramps, plinth beams, cable trenches in Soft rock not requiring blasting but other than hard rock including shoring, strutting, sorting out and stacking useful material, dewatering where required, and disposing off the excavated stuff upto all lead and lift

EXCAVATION 3.00 to 5.00 Metre for foundation such as footing, pedestals, walls, drains, columns, ramps, plinth beams, cable trenches in Soft rock including shoring, strutting, sorting out and stacking useful material, dewatering where required, and disposing off the excavated stuff upto all lead and lift

EXCAVATION 3.00 to 5.00 Metre for foundation such as footing, pedestals, walls, drains, columns, ramps, plinth beams, cable trenches in Hard rock including shoring, strutting, sorting out and stacking useful material, dewatering where required, and disposing off the excavated stuff upto all lead and lift

Providing and laying RUBBLE SOLING wherever required in foundation and plinth including hand packing fillings interstices with chips and sand. Watering and compacting to consolidated thickness, etc complete as directed by engineer-in-charge

Providing material and labour for laying PLINTH PROTECTION including excavation of 30 cm depth and Filling with dry bricks bats of 20 cm thick and top layers C.C. 1:2:4 ( 1 cement 2 coarse sand: 4 graded stone aggregate 20m nominal size)50mm thk finished in proper grade and slop etc. complete as directed by engineer-in-charge

Carring out plinth treatment to post construction / existing structure by spraying chemical solution for termite control treatmentincluding labour and material consistment with I.S.I specification.Using Chlordene and Chiorpurfiles 20 EC. As Per 6131_paret-II Consentration Weight one percent is recommended i.e one litre 20 EC chemical emulsion with 19 liter give 1 % concrentration inclusive of one litre chemical emulsion appication at the rate of 5 Litre chemical / Sqm of surface is recommended as per I.S. treated Plinth area of structure to be measured for payment as directed by engineer-in-charge

Providing and laying Granular sub­base (GSB) for preparing base of road by providing close graded Material, mixing in a mechanical mix plant at OMC(Optimum Moisture Content), carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete.

Providing and laying PLAIN CEMENT CONCRETE 1:2:4 (1- Cement : 2- Coarse sand : 4- graded stone aggregates 20 mm nominal size) in foundations and superstructure including, machine mixing, leveling compacting, curing and formwork if any, scaffolding, staging etc. complete as directed and instructed by Engineer-in-Charge. Volume of PCC laid to be measured for payment.

Providing material and labour for laying machine mixed/machine batched/RMC controlled cement concrete M.250 using graded black trap stone aggregates of maximum 20mm nominal (down graded) size including fine aggregate confirming to IS 383 with minimum cement content as per IS456 (without flyash) for durability shall be followed as per approved design mix & latest IS456 for reinforced cement conrete work for all elements,all floors,all heights/depths, any lead and lift including cost of formwork with sheathing steel , scaffolding, staging, vibrating, compacting, finishing and curing complete but excluding cost of reinforcement for reinforced concrete work in Foundations, footings, Base of columns and Mass concrete, as directions of Engineer in charge Complete. Preliminary cubes to be prepared on award of work and to be tested to meet the specified requirement for M25 mix, design mix to be approved by the Engineer-in-charge/Architect. Concrete placing shall be done with utmost care, the free drop height shall not exceed 1.5m, and concrete shall be vibrated with immersion type vibrators having frequency not less than 7000 vibrations per second in methodical method so as all points of structures are covered. Free concrete surface shall be covered with Hessian cloth and kept wet.

Providing material and labour for laying machine mixed/machine batched/RMC controlled cement concrete M.250 using graded black trap stone aggregates of maximum 20mm nominal (down graded) size including fine aggregate confirming to IS 383 with minimum cement content as per IS456 (without flyash) for durability shall be followed as per approved design mix & latest IS456 for reinforced cement conrete work for all elements,all floors,all heights/depths, any lead and lift including cost of formwork with sheathing steel , scaffolding, staging, vibrating, compacting, finishing and curing complete but excluding cost of reinforcement for reinforced concrete work in Columns, Pillars posts and struts etc complete as directed by Engineer-incharge. Preliminary cubes to be prepared on award of work and to be tested to meet the specified requirement for M25 mix, design mix to be approved by the Engineer-in-charge/Architect. Concrete placing shall be done with utmost care, the free drop height shall not exceed 1.5m, and concrete shall be vibrated with immersion type vibrators having frequency not less than 7000 vibrations per second in methodical method so as all points of structures are covered. Free concrete surface shall be covered with Hessian cloth and kept wet.

Providing material and labour for laying machine mixed/machine batched/RMC controlled cement concrete M.250 using graded black trap stone aggregates of maximum 20mm nominal (down graded) size including fine aggregate confirming to IS 383 with minimum cement content as per IS456 (without flyash) for durability shall be followed as per approved design mix & latest IS456 for reinforced cement conrete work for all elements,all floors,all heights/depths, any lead and lift including cost of formwork with sheathing steel , scaffolding, staging, vibrating, compacting, finishing and curing complete but excluding cost of reinforcement for reinforced concrete work in Lintels,Beams,Girders and Cantilever etc complete as directed by Engineer-incharge. Preliminary cubes to be prepared on award of work and to be tested to meet the specified requirement for M25 mix, design mix to be approved by the Engineer-in-charge/Architect. Concrete placing shall be done with utmost care, the free drop height shall not exceed 1.5m, and concrete shall be vibrated with immersion type vibrators having frequency not less than 7000 vibrations per second in methodical method so as all points of structures are covered. Free concrete surface shall be covered with Hessian cloth and kept wet.

Providing material and labour for laying machine mixed/machine batched/RMC controlled cement concrete M.200 using graded black trap stone aggregates of maximum 20mm nominal (down graded) size including fine aggregate confirming to IS 383 with minimum cement content as per IS456 (without flyash) for durability shall be followed as per approved design mix & latest IS456 for reinforced cement conrete work for all elements,all floors,all heights/depths, any lead and lift including cost of formwork with sheathing steel ,scaffolding, staging, vibrating, compacting, finishing and curing complete but excluding cost of reinforcement for reinforced concrete work in Slabs ,landing, shelves, Balconies, Lintels, Beams, Girders and Cantilever etc complete as directed by Engineer-incharge. Preliminary cubes to be prepared on award of work and to be tested to meet the specified requirement for M25 mix, design mix to be approved by the Engineer-in-charge/Architect. Concrete placing shall be done with utmost care, the free drop height shall not exceed 1.5m, and concrete shall be vibrated with immersion type vibrators having frequency not less than 7000 vibrations per second in methodical method so as all points of structures are covered. Free concrete surface shall be covered with Hessian cloth and kept wet.

Providing material and labour for laying machine mixed/machine batched/RMC controlled cement concrete M.250 using graded black trap stone aggregates of maximum 20mm nominal (down graded) size including fine aggregate confirming to IS 383 with minimum cement content as per IS456 (without flyash) for durability shall be followed as per approved design mix & latest IS456 for reinforced cement conrete work for all elements,all floors,all heights/depths, any lead and lift including cost of formwork with sheathing steel , scaffolding, staging, vibrating, compacting, finishing and curing complete but excluding cost of reinforcement for reinforced concrete work in Slabs, landing, shelves and Cantilever etc complete as directed by Engineer-incharge. Preliminary cubes to be prepared on award of work and to be tested to meet the specified requirement for M25 mix, design mix to be approved by the Engineer-in-charge/Architect. Concrete placing shall be done with utmost care, the free drop height shall not exceed 1.5m, and concrete shall be vibrated with immersion type vibrators having frequency not less than 7000 vibrations per second in methodical method so as all points of structures are covered. Free concrete surface shall be covered with Hessian cloth and kept wet.

Providing material and labour for laying machine mixed/machine batched/RMC controlled cement concrete M.250 using graded black trap stone aggregates of maximum 20mm nominal (down graded) size including fine aggregate confirming to IS 383 with minimum cement content as per IS456 (without flyash) for durability shall be followed as per approved design mix & latest IS456 for reinforced cement conrete work for all elements,all floors,all heights/depths, any lead and lift including cost of formwork with sheathing steel , scaffolding, staging, vibrating, compacting, finishing and curing complete but excluding cost of reinforcement for reinforced concrete work in WALLS from top foundation level to all levels etc complete as directed by Engineer-incharge. Preliminary cubes to be prepared on award of work and to be tested to meet the specified requirement for M25 mix, design mix to be approved by the Engineer-in-charge/Architect. Concrete placing shall be done with utmost care, the free drop height shall not exceed 1.5m, and concrete shall be vibrated with immersion type vibrators having frequency not less than 7000 vibrations per second in methodical method so as all points of structures are covered. Free concrete surface shall be covered with Hessian cloth and kept wet.

Providing material and labour for laying machine mixed/machine batched/RMC controlled cement concrete M.250 using graded black trap stone aggregates of maximum 20mm nominal (down graded) size including fine aggregate confirming to IS 383 with minimum cement content as per IS456 (without flyash) for durability shall be followed as per approved design mix & latest IS456 for reinforced cement conrete work for all elements,all floors,all heights/depths, any lead and lift including cost of formwork with sheathing steel , scaffolding, staging, vibrating, compacting, finishing and curing complete but excluding cost of reinforcement for reinforced concrete work in Staircases complete as directed by engineer-incharge. Preliminary cubes to be prepared on award of work and to be tested to meet the specified requirement for M25 mix, design mix to be approved by the Engineer-in-charge/Architect. Concrete placing shall be done with utmost care, the free drop height shall not exceed 1.5m, and concrete shall be vibrated with immersion type vibrators having frequency not less than 7000 vibrations per second in methodical method so as all points of structures are covered. Free concrete surface shall be covered with Hessian cloth and kept wet.

Providing, laying and fixing in position REINFORCEMENT High yield deformed bars/TMT/CRS FE500/FE500D/FE550 for R.C.C. works at all levels including cutting, bending and binding with 16 gauge M.S. annealed wire, providing cover blocks of C.M. 1:2 Embedded with binding wire etc. complete. The reinforcement detailing to IS 456 or, if specified by engineer, shall conform to IS: 13920 (Ductile detailing of R. C. Structures), bars as per IS 1786 the rate shall be inclusive of executing such detailing. Laps to be measured shall be as shown in drawing and for reinforcement length longer than available in market. Chairs, pins and laps other than that specified shall not on be measured and paid for. No extra to be paid for height, rate remains same at all levels, complete as per drawings, specification, direction of engineer-incharge. Make: TATA, SAIL, JSW, or EQUIVALENT.

Providing material and labor for Structural steel work (Confirming to IS 4923-1997) riveted, bolted or welded in builtup for all type sections, in framed work, including cutting, hoisting, fixing in position and applying a priming coat &two coat applying synthetic enamel paint of approved steel primer all complete as per the structural designs and as directions of chief Engineer- in -Charge Complete.

Brick work using common burnt clay building bricks including scaffolding, raking of joints, curing using first class bricks having min. comp. Strength 35 kg/cm2 of approved manufacturer in foundation and plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand)(B)Conventional All bricks and shall be soaked in water for at least 24 hours before use. bricks used for masonry work shall be as available locally, but approved before start of work. volume of masonry to be measured for payment.

Providing & fixing LIGHT WEIGHT MASONRY BLOCKS of- Sand Based Autoclaved Aerated Concrete blocks (AAC Blocks) of approved make, upto all floor level/all heights, masonry walls in jointing mortar, complete as per Technical specification, density of blocks shall not exceed 700 kg/cum, using bonding material supplied by the manufacturer as per their instructions, including necessary scaffolding for fixing, in line & level. Volumne of blocks erected to be measured for payment. R.C.C. coping of size-wall thickness x 100mm ht. at 0.91m intervals shall be provided including reinforced with 2 Numbers 6mm diameter horizontal bars and 6mm diameter at 200 c/c ties. R.C work not to be measured separately but included in rate.

Providing & fixing upto 150mm thick LIGHT WEIGHT MASONRY BLOCKS of- Sand Based Autoclaved Aerated Concrete blocks (AAC Blocks) of approved make, upto all floor level/all heights, masonry walls in jointing mortar, complete as per Technical specification, density of blocks shall not exceed 700 kg/cum, using bonding material supplied by the manufacturer as per their instructions, including necessary scaffolding for fixing, in line & level. Area of blocks erected to be measured for payment. For wall thickness up to 150mm, R.C.C. coping of size-wall thickness x 100mm ht. at 0.91m intervals shall be provided including reinforced with 2 Numbers 6mm diameter horizontal bars and 6mm diameter at 200 c/c ties. R.C work not to be measured separately but included in rate.

Providing and laying 10mm thick in single coat CEMENT PLASTER in (i)Cement mortar 1:3 (1-cement:3-sand) at all height/all floors to internal surfaces of all elements, walls, R.C.C. work, Ceiling,[backing coat at places where glazed or ceramic tiles are to be fixed etc]. including hacking of concrete surfaces, racking of joints, scaffolding, curing etc. complete. Final finished surface shall be little rough , so as it has proper bonding to paint putty. The surfaces to be plastered to be hacked immediately on de-shuttering. The Brick/ RCC surface to be plastered to be cured sufficiently before start of plaster. Initial bare surface area to be Plastered shall be measured for payment unless noted otherwise, etc as directions of Engineer in charge Complete.

Providing and laying 20mm thick SANDFACED CEMENT PLASTER of required grain finishing upto all height/all floors including grooves, pattas etc. in two coats having the the base coat of not less than 12 mm thickness in CM 1:3 (1-cement : 3-sand) & finished coat 8 mm thk, in CM 1:1 (1-cement : 1-sand) to external surfaces of concrete & masonry including hacking of concrete surfaces, racking of joints, scaffolding, curing etc. complete. Rate shall include addition of “Impermo” water proofing compound or equivalent, providing, adding & mixing of fine fibrillated 100% virgin polypropylene fibers in cement mortar to form homogeneous mixture @125 gms per a bag of cement in both the coats of plaster, 12mm long fibers shall be used in first coat & 6mm long fibers shall be used in second finished coat. providing drip mould 40mm wide and 12mm thick in cement mortar 1:3 on soffit of chajjas, canopies, gutters etc.complete. as directions of Engineer in charge Complete. The surfaces to be plastered to be hacked immediately on de-shuttering. The Brick/ RCC surface to be plastered to be cured sufficiently before start of plaster. Initial bare surface area to be Plastered shall be measured for payment unless noted otherwise, etc as directions of Engineer in charge Complete.

Providing material and labor for applying Two coats of gypsum including providing grooves at all the edges of windows/Doors with neat finish on new wall surface to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth.make the surface uniform and levelled and must be without any undulation as directed by engineer in charge complete. Make: Diamond gypsum or its equivalent.

Providing material & labour for Internal Wall painting (two coats) with Premium Emulsion of approved brand and manufacture including primer coat on undecorated wall surface to give an even shade including throughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth. as directed by engineer in charge complete. emulsion that must offer protection against different varieties of bacteria and fungus. The product shall be independently tested and approved for properties alike resistance to bacterial and fungal species, crack tolerance and flame spread resistance. The coating shall contribute to satisfying the following credit(s):  Indoor Environmental Quality (IEQ) under LEED® 2009  Environmental Quality (EQ) and Materials and Resources (MR) under LEED® v4 This product shall have a VOC limit not more than 24 g/lit. The product can be like Asian apcolite emulsion or Jotun Paints or approved equivalents. Two Coats of above paint should be applied using conventional Roller / Airless spray at the site after application and drying of applied Putty-Primer. For measurement of painting items the area painted shall be considered without any multiplication factor for different kinds of surfaces painted. Rate shall be quoted accordingly. All painting items final finish shall be as per manufacturer's specification as per acceptance of Engineer in charge /Architect. No extra payment shall be made for extra/over coat if required. The rate shall be inclusive of providing bamboo scaffolding Make: Jotun,Asian Paints, Berger Paints, Dulux Paints or equivalent.

Providing material & labour for Internal Wall painting (two coats) with Synthetic enamel paint of approved brand and manufacture including suitable primer coat on undecorated wall surface to give an even shade including throughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth. as directed by engineer in charge complete. The product can be like Asian apcolite premium enamel or approved equivalents. Two Coats of above paint should be applied using conventional Roller / Airless spray at the site after application and drying of applied Putty-Primer. For measurement of painting items the area painted shall be considered without any multiplication factor for different kinds of surfaces painted. Rate shall be quoted accordingly. All painting items final finish shall be as per manufacturer's specification as per acceptance of Engineer in charge /Architect. No extra payment shall be made for extra/over coat if required. The rate shall be inclusive of providing bamboo scaffolding Make: Jotun,Asian Paints, Berger Paints, Dulux Paints or equivalent.

Providing material & labour for Artistic Internal Wall painting (two coats) with Luxury Emulsion of approved brand and manufacture including suitable primer coat on undecorated wall surface to give an even shade including throughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth. as directed by engineer in charge complete. One component waterborne 100% pure acrylic interior eggshell emulsion that must offer protection against different varieties of bacteria and fungus. Paint should free of HCHO, APEO and have crack bridging property of min 0.9 mm with class 1 flame spread resistance The product shall have a Volume Solids of minimum 35% The product shall be independently tested and approved for properties alike resistance to bacterial and fungal species, crack tolerance and flame spread resistance. The coating shall contribute to satisfying the following credit(s):  Indoor Environmental Quality (IEQ) under LEED® 2009  Environmental Quality (EQ) and Materials and Resources (MR) under LEED® v4 This product shall have a VOC limit not more than 24 g/lit. The product can be like Asian paint Royale series or approved equivalents. Two Coats of above paint should be applied using conventional Roller / Airless spray at the site after application and drying of applied Putty-Primer. For measurement of painting items the area painted shall be considered without any multiplication factor for different kinds of surfaces painted. Rate shall be quoted accordingly. All painting items final finish shall be as per manufacturer's specification as per acceptance of Engineer in charge /Architect. No extra payment shall be made for extra/over coat if required. The rate shall be inclusive of providing bamboo scaffolding Make: Jotun,Asian Paints, Berger Paints, Dulux Paints or equivalent. Guidelines for application 1. Surface Preparation - Inspection: Assess the wall surface for defects like cracks, moisture, or old paint layers. All imperfections must be fixed before starting the painting process. - Cleaning: Clean the wall to remove dust, grease, and loose particles. Use a mild detergent solution or a vacuum to ensure a clean surface. - Repair: Fill cracks, holes, and other imperfections with a suitable filler (e.g., putty or spackle). Sand the area smooth after drying. - Priming: Apply a suitable primer to the wall to ensure proper adhesion of the artistic paint. Choose a primer based on the wall material (e.g., masonry, drywall, plaster). Allow the primer to dry according to the manufacturer's instructions. 3. Application Process - Base Coat: - Apply a base coat of paint, using a roller for large areas and a brush for edges and corners. Choose a base color that complements the final artistic design. - Allow the base coat to dry completely - Artistic Painting: - As per details provided by architect, Plan the design by sketching it lightly on the wall with a pencil or chalk & get necessary approval from architect or engineer-in-charge. Post approval proceed for final application. 4. Finishing - Sealing (Optional): Apply a clear sealer or varnish over the artwork for added protection, a matte, satin, or gloss finish based on the desired effect. 6. Quality Standards - Adhesion: Paint should adhere firmly to the wall without peeling or flaking. - Finish: The final surface should be even, free of brush marks, and match the intended artistic design. - Durability: The painted surface should withstand normal wear and cleaning without damage

Supplying & Providing two coat of primer and two coats of Texture paint, ANTIFUNGAL PAINT, water proof, dust proof Paint on Exterior Surfaces at all heights of surfaces. One component waterborne 100% pure acrylic emulsion that offers protection against concrete carbonation with an R Value of min 600m and an equivalent concrete layer thickness value of min 150cm. Paint should have crack bridging property of min 1.85 mm with Solar Reflective index of min 110 and IR reflectance property. The product shall have a Volume Solids of minimum 35% The product shall be independently tested and approved for properties alike Carbon Dioxide Diffusion resistance, resistance to chloride diffusion, crack bridging and liquid water/ vapour transmission as well as SRI properties. The product can be like Jotashield WaterXtreme Topcoat of Jotun Paints or approved equivalents. Two Coats of above paint should be applied using a conventional Roller / Airless spray at the site after application and curing of applied Primer. including cleaning, preparing the surface, applying primer - scraping by sandpaper, scaffolding etc. including - (a) All surface preparation, suitable number of base coats required, primers and suitable finishing to the complete satisfaction of the Engineer in Charge, (b) Scaffolding and all leads and lifts,(c) Proper curing in between the two subsequent coats, (d) Touch ups to the paint after the scaffolding is removed, (e) All measurements for paints to be as per IS-1200. f) Minimum Guarantee of Ten Years Waterproofing and Paint performance for all external paints by manufacturer . For measurement of painting items the area painted shall be considered without any multiplication factor for different kinds of surfaces painted. Rate shall be quoted accordingly. All painting items final finish shall be as per manufacturer's specification as per acceptance of Engineer in charge /Architect. No extra payment shall be made for extra/over coat if required. Make - Asian Paint Ultima Allura Torino, Jotun Jotashield Tex Fine OR Equivalent.

Providing and applying 3mm Thk. PUcrete for floor of approved quality including cleanig,Rubbingetc.,includingGrindingwith vacuum dust free, Gripping ( 4mm deep ), Prime coat ( 1 MM ), Top coat with required color for final finish( 2 mm thick), colour and shade to new surface in three coats etc. complete.

Providing & Applying 3-part Epoxy based high strength mortar that forms an bacterial resistant, chemical & abrasion resistant Coving in the juncture of wall & floor as well as between wall to wall having 75mmx75mm widht. Overcoating with epoxy coating/topping is mandatory to achieve aesthetic appeal & also to obtain hygienic environment.as directions of Engineer in Charge Complete.

ALUMINIUM WORKS -Doors and Windows work Providing material and labour for fixing in position frames, shutter for any type of aluminium work for any type of door, window, partition, made out of any type of aluminium sections of approved make having minimum 50 micron pure polyester powder coating of approved shade, texture & colour of approved make for all floors, all levels, all heights, all shapes, all sizes including cutting, bending, crimping, fabricating in best workmanship manner etc as per the drawing, specification and as directed by Architect or Engineer-in-Charge. Contractor shall prepare shop drawing based on concept drawing and get approved from the consultants before procurement of material. All loose material shall be approved. Mockup of one/two window shall be executed as per approved shop drawing with all hardware. Work shall carried out as per the approved shop drawings, approved mock-up and approved sample. Actual weight of installed Aluminium sections (for using fabrication without considering any wastage) shall only be measured and shall be considered for the payment. Glazing shall be paid as seperate item. Contractor shall provide guarantee for stability, water tightness etc for 12 months after defects liability period. Rate shall be inclusive of providing aluminium sections, cutting, fabrication, errection and fixing to the best workmanship manner, including 1) Sheet metal screws and casted solid aluminum corner cleats fixed with external byttins with a spring for rapid and secure joint assembly for casement and sliding shutter and frame; 2) Glazing clips for receiving infill panel; 3) Best quality wool pile where ever shutter touches the frame and compatible microwave cured EPDM rubber; 4) Dash Anchor fasteners of HILTI HRDUGT or equivalent for fixing the frame assembly to the RCC or masonry surfaces. Minimum 1 anchor fastener shall be used for every 600 mm length of section for stability of frame. 5) 10mm GI tie rod for connecting vertical stile at top and bottom for aluminum door shutter and 4mm thick solid aluminium corner cleat of full thickness of section for connecting style and horizontal rails; 6) providing and fixing packing (rough ground) in full periphery/ at every 600mm c/c with average 6 mm thick PVC spacer/ compact sheet of width (equal to section width less 30mm for backer rod and sealant); 7) Filling the gap between wall and frame on both sides (outside and inside) with polyethylene baker rod of avg. 10 mm thickness of approved make and color and then sealing the remaining gap with neutral grade G/M (Glazed & Metal) weather silicon sealant of approved make and color. 8) Termite treated seasoned teak wood as infill material to installe hardware in door shutter and frame as and when required, etc as per directions of Engineer in charge Complete. Make:- Jindal or equivalent as approved by Engineer-in-charge

Providing & Fixing Louvers and Fins (made out of Aluminium Section) Providing, fixing, designing aluminium fixed louver of any type of louver section of approved make having minimum 50 micron polyster powder coating on all the surfaces of approved shade, texture & make as per manufacturer's specifications. Contractor shall submit the shop drawing for louver/ fins based on concept design/ drawing and as per elevation. Aluminium louver section shall be fixed on aluminium framing/ carrier/ panel/ GI clip and necessary sub structure with required fastners, hardware as per approved shop drawing etc complete for all floor, all height including scaffolding as directed by engineer in charge. Louver, framing and sub structure shall be in proper line, level and plumb. Necessary MS work shall be paid in relevant tender item.

Providing material and labour for fixing 6mm thick Compact Sheet of any size, any shape, any color (single side, double side coloured), any texture of approved make and as per approved sample (approved by architect). Compact sheet shall be fixed in aluminium frame and shutter work with necessary cutting of sheet, provision of groove, filling of groove (both side) as per drawing & specifications including providing and fixing EPDM quality rubber/ silicon sealant/ adhesive tape/ screwing on the periphery of the sheet as per the required thickness etc. complete at all floors/ all levels/ all heights as per the drawing & directed by Engineer in charge. Cut edges of the compact sheet shall be provided with masking tape. Actual installed quantity shall be measured and paid.

Providing material and labour for fixing factory made and pressed laminated 35mm thick flush door shutter of specificied thickness made of ISI marked non decorative type flush door shutters confirming to IS- 2202 (Part 1), core of block board construction with aluminium frame and face veneers (IS 710 Grade) on both faces of shutters having 1 mm thick decorative type laminates of approved make, shade, finish on both faces of shutter fixed with phenol formaldehyde synthetic resin type adhesive conforming to IS 848 including providing and fixing external lipping with 2nd class teak wood battens, exposed (37mm x 12mm)/ concealed (35mm x 12mm) on all edges of door shutter as required with 2 coats of synthetic enamel painting including 1 coat of wood primer & lapi/ lacquer polishing with primer to all exposed side of lipping, all as per approved drawing, for all floor, all level all height etc. complete as directed by Engineer-in-charge. Measurement including lipping shall be considered for payment. Necessary hardware like hinges, pivot, handle, tower bolts, locks etc shall be separately measured and paid in the relevant tender items. Cost of laminates shall be paid in relevant tender item.

Providing and fixing 30mm thick factory made wire guazed solid PVC Door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles and 15mm x 15mm for top, lock and bottm rails, M.S. frame shall have a coat of steel primers of approved make and manufacture, 19mm x 19mm M.S. square tubes shall be coveed with 5mm thick head mouled PVC ‘C’ channel of size 30mm thickness, 90mm width out of which 75mm shall be flat and 15 mm shall be bent in 90 degree angle on either side forming stiles and 5mm thick 115mm wide PVC sheet out of which 100mm shal be flat and 15mm shal be betn in 90 degree on the inner side to from top and bottom rails and 130mm wide PVC sheet out of which 100mm shal be flat and 15mm shal be bent in 90 degree on both side to from lock rail10mm (5mm x 2) thick, 20mm wide cross PVC sheet as gap insert for top rail and bottom rail, panel will be of G.I. wire gauge of 24 gauge to be fitted in by ‘C’ channel of size 10mm x 35mm on the either side in the stiles.The inner side ‘C’ channel is fixed by 19mm x 19mm M.S. tube on both side with screws. The wire mesh in top, bottom and lock rail is sealed with 15mm x 15mm tube with G.I.wire, 1mm (5mmm x 2) thick PVC strip of 25mm width is to be stuck and screw on both side of G.I. wire guage interior at the top, bottom and lock rails. An additional 5mm thck PVC strip of 20mm width is to be stuck on the interior side of the ‘C’ channel using PVC solvent cement adhesive etc. complete as per dirction of Engineer in charge, manufacture’s specification and drawing.

Providing material and labour for fixing 1 mm thick Laminate sheet of any size, any shape, any color, any texture of approved make and as per approved sample (approved by architect) on Non decorative flush door, panelling work, fixed partition, any ply surface etc with necessary nails, screws, adhesives as per drawings and as per approved sample. The rate shall be for all heights, all floors, all places etc complete as directed by engineer in charge. Actual laid area shall be measured and paid without considering any westage. Laminates and ply shall be factory pressed.

Providing material and labour for fixing 6mm thick Clear Normal Glass as per approved sample of any size, any shape and specified thickness in frame and shutter work with necessary cutting of glass as per drawing & specifications including providing and fixing EPDM quality rubber/ silicon sealant/ structural sealant and 3M tape on the periphery of the glass as per the required thickness etc. complete at all floors/ all levels/ all heights as per the directions of Engineer in charge. Actual installed quantity shall be measured and paid.

Providing material and labour for fixing 6mm thick Clear Toughen Glass as per approved sample of any size, any shape and specified thickness in frame and shutter work with necessary cutting of glass as per drawing & specifications including providing and fixing EPDM quality rubber/ silicon sealant/ structural sealant and 3M tape on the periphery of the glass as per the required thickness etc. complete at all floors/ all levels/ all heights as per the directions of Engineer in charge. Actual installed quantity shall be measured and paid.

Notes for Hardware : Supplying and fixing heavy quality fixtures and fittings for doors, windows, ventilators, partition wall, cabinets with necessary screws, nails, machine pins etc at all floor/ all levels/ all heights complete. Sample shall be approved by Architect before execution. As per description, SS hardware shall be of 304 grade or 316 grade as per item description and as per approved sample. The fixture & fastenings shall be provided as under : Providing material and labour for fixing single/ double action hydraulic floor spring with SS cover plate & adjustable concealed casted top pivot (two piece) and bottom strap of approved make for wooden/ aluminium doors of minimum 100kg capacity with minimum one year guarantee. Rate shall be inclusive of cutting of floor neatly, grouting the floor spring & cleaning/ polishing the floor & maintaining in good working condition until defect liability period. In case of Aluminium shutter bottom arm of floor spring & top pivot shall be firmly fixed in the aluminium members using required size of teak wood by making rabbet in the wood. The Floor Spring shall conform to EN 1154. a) Hold open having for shutter width upto 1200mm with standard spindle and cover plate. Closing force complying with EN 1154 2-4

Providing & Fixing heavy quality SS 304 heavy pivot top & bottom (pair) of approved make with SS screws ect complete as directed by engineer in charge.

Providing material and labour for fixing hydraulic rack and pinion door closer with standard arm (Silver finish) with screws to pivoted/ hinged door of approved make for specified door width with minimum 100kg capacity and one year guarantee. All adjustment screws face fixed. Rate shall be inclusive of fixing with using the template as per manufacturer’s specification & maintain in good working condition until defect liability period. The door closer shall conform to EN 1154 standard. a) with standard/ hold open arm with two independent closing valves and latching speed adjustable by arm without mounting back plate, Closing force complying with EN 1154 2 - 4 for up to 900 mm door shutter width

Providing material and labour for fixing SS 316 grade butt hinge of average 100 x 75 x 3 mm - with ball bearing of approved make as per approved sample with necessary screws etc. complete for all floor all height all level as directed by Engineer in Charge.

Providing material and labour for fixing set of dead lock of approved make with 50mm backseat, 20mm square for end with 72 mm centers including strike plate in satin stainless steel finish as per DIN 18251-1, grade 2 and prepared for euro profile cylinder (EPC) including strike plate and EPC length 60/70 mm standard Euro profile Pin Cylinder/ Half pin cylinder with both side key/ one side key one side knob operation with one pair of SS 316 grade Escutcheons (key hole plate) for wooden/ aluminium/ metal doors with necessary SS Phillips head screws etc complete for all floor, all level, all height as per approved sample and as directed by engineer in charge. The lock shall be with 3 keys.

Providing material and labour for fixing SS 304 satin finished set of narrow style dead lock of approved make with 25mm /35 mm set back necessary euro profile pin cylindrical lock 60/ 70 mm for Key and or knob operation and one pair of SS 316 grade Escutcheons (key hole plate) for aluminium door with necessary SS Phillips head screws etc complete for all floor, all level, all height as per approved sample and as directed by engineer in charge. The lock shall be with 3 keys.

Providing material and labour for fixing Mortise lock of approved make having 72mm centre to centre, 55mm Backset 20mm Square forend and 60/ 70mm standard Europrofile Pin Cylinder with both side key /one side key - one side knob operation and SS 316 grade hollow tubular pipe pair of Mortise handle of 22mm dia 150mm long with a pair of SS 304 Escutcheons (key hole plate) for wooden /aluminium/ metal doors with necessary ss phillips head screws etc complete for all floor, all height, all level as per approved sample as directed by engineern in charge. The lock shall be with 3 keys.

Providing material and labour for fixing Mortise shaft dead bolt of approved make with key (Alen Key lock), sleeve with 57mm backset and 25mm square forend in stainless steel satin finish etc complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.

Providing material and labour for fixing Zinc material indicator bolt of approved make for toilet door with Thumb Turn inside & Emergency Release & Indicator Outside with necessary screws etc complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.

Providing material and labour for fixing SS 316 grade push-pull pair of handle of size 200 mm long x 19mm dia made out of satin (brush) finish hollow pipe of 1.5mm thick having offset type (C or D shape)/ H-shape/ D-shape of approved make with necessary screws etc. complete for wooden doors/ aluminium doors/ metal doors for all heights, all floors and all level as per approved sample and as directed by Engineer-in-charge. Rate shall be The length of handle should be perfect center to center as below specified.

Providing material and labour for fixing SS 316 grade handles 150mm long D shape hollow tube handle of approved make with both end bracket with necessary screws etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.

Providing and Fixing SS 304 Grade Satin Finish 1.8 mm Thickness Aldrops of 16 mm dia x 250 mm including 3 nos. fixing Bracket and 1 no. locking bracket of approved make with necessary MS nickle Plating Bolts etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.

Providing and Fixing SS 304 Grade Satin Finish 1.8 mm Thickness Tadi of 12mm dia x 200mm including 3 nos.fixing Bracket of approved make with necessary screws, pins, bolts etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.

Providing material and labour for fixing SS 304 brush finish solid Door Stopper with magnet, fixed type, wall mounted (square/ round) of approved make with necessary screws etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.

Providing material and labour for fixing SS 304 grade brush finish solid Door bufer with pvc base, wall mounted (square/ round) of approved make with necessary screws etc. complete as approved by Engineer-in-charge in Charge.

"Providing material & labor for laying Anti-Skid Vitrified 8 to 10 mm thick tile flooring over 20 mm (average) base of cement mortar 1:4 ( 1 cement: 4 coarse sand) on new surface and spacer of required size to be provide while fixing the tile. Tiles joint grooves to be filled with epoxy. including finished with flush pointing & cleaning the surface etc. complete. Tile sample must get prior approval of architect or by engineer-in-charge Make: Nitco, Simpolo, Kajaria, johnson, Rak or equivalent"

Providing and laying VITRIFIED TILES 8mm thick, in dado, vertical surfce, etc make of first quality at all locations and levels in cement mortar bedding 12mm thick ( 1:3 mix ) or back coat plaster of required thickness with neat cement float backing filling the joints with white cement with pigment of matching colour of the tiles , cleaning, washing with dilute acid etc. complete. The tiles shall be soaked in water for at least 10 hours prior to fixing. The tile before fixing shall be properly approved from architect or engineer-in-charge. The tiles shall be fixed in such a manner that no edges of the tile shall be seen at the corners. The workmanship shall be to the satisfaction of the Architect or engineer-in-charge. Make: Nitco, Simpolo, Kajaria or equivelant

Providing and laying 25mm think Mirror polished Kota stone flooring, treads in steps, etc of approx. size 450 x 600 or 600 x 600 in approved shade, all edges manually dressed at all locations and level in cement mortar bedding ( 1:2 mix ) in flooring including filling joints with net cement, curing and fine smooth wax polishing in situ after laying & final setting including scratch less polish with mechanically operated machine. The surface of the kotah stone shall be smooth & fine after fixing without any offset at joints,including rubbing and polishing cleaned to the satisfaction of architect or engineer-in-charge

Providing and laying 75mm high x 20mm thick Kota stone Skirting with manual polishing and including of chiseling the wall surface to make the Kotah flush with the wall surface in approved shade, all edges manually dressed at all locations and level in cement mortar bedding ( 1:2 mix ) in walls including filling joints with net cement, curing and fine smooth wax polishing in situ after laying & final setting including scratch less polish with manually. The surface of the kotah stone shall be smooth & fine after fixing without any offset at joints,including rubbing and polishing cleaned to the satisfaction of architect or engineer-in-charge

"Providing material & labor for laying ACID-PROOF TILE 8 to 10 mm thick tile flooring over 20 mm (average) base of cement mortar 1:4 ( 1 cement: 4 coarse sand) on new surface and spacer of required size to be provide while fixing the tile. Tiles joint grooves to be filled with epoxy. including finished with flush pointing & cleaning the surface etc. complete. Tile sample must get prior approval of architect or by engineer-in-charge Make: Nitco, Simpolo, Kajaria, johnson, Rak or equivalent"

Providing and laying ACID PROOF TILES 8mm thick, in dado, vertical surfce, etc make of first quality at all locations and levels in cement mortar bedding 12mm thick ( 1:3 mix ) or back coat plaster of required thickness with neat cement float backing filling the joints with white cement with pigment of matching colour of the tiles , cleaning, washing with dilute acid etc. complete. The tiles shall be soaked in water for at least 10 hours prior to fixing. The tile before fixing shall be properly approved from architect or engineer-in-charge. The tiles shall be fixed in such a manner that no edges of the tile shall be seen at the corners. The workmanship shall be to the satisfaction of the Architect or engineer-in-charge. Make: Nitco, Simpolo, Kajaria or equivelant

Providing material & labour for Fixing 15 mm thick Full body heavy duty vetrified tiles, premoulded and prepolished machine cut for platforms, vanity counters, door window, sills, jambs, soffits facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding on all exposed edges and polishing to edge to give high gloss finish etc. complete. at all levels. Make: Somany Duragres granit series or equivalent as approved by engineeri-in-charge

Providing material & labour for stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade. FOR URINAL PARTITIONS

Providing material and labour for making Black Granite stone Counter Ticket/Wash Basin/Food Stall of 0.60mt wide with vertical & Horizontal Support of granite stone and having bottom slab of 25mm to 30mm thick kadappa stone fixing with cement motar 1:4 (1 Cement :4fine sand) and neat cement slurry as per requirement including cutting the granite stone for fixing any shape of wash basin of any size in line & level. All exposed Edges of granite should be moulded including all accessories etc. as directed by Enginner on Charge.

Providing material and labour for fixing 25mm to 30mm thick kadappa stone on parapet wall with cement motar 1:4 (1 Cement : 4 fine sand) and neat cement slurry as per requirement including cutting the kadappa stone etc. as directed by Enginner on Charge.

Providing material and labour for applying Chemical Waterproof Coating PU One Coat epoxy primer and Three coat polyrethane coating including preparation of surface as required for terraces and Toilets. as approved by the Chief engineer-incharge with a guarantee of 10 years. Complete. Make:- MYK Arment, Pidilite, Sika or equivelant.

Providing material, Labour and equipments for Providing and laying integral Cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc. consisting of following operations : a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer in charge over the RCC Slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks / brick bats 25mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in charge over 20mm thick layer of cement mortar of mix 1:5 ( 1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junction of walls and slabs. c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg / sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in charge. d) Finishing the surface with 20mm thick jointless cement mortar of mix 1:4 ( 1 cement : 4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300 x 300 mm square 3 mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer in charge : Including Khurra & Gola work with average thickness of 120mm and minimum thickness at Khurra as 65 mm etc. complete as directed by Chief Engineer in charge.

Providing and fixing in position Stainless steel Railing, The railing is made of stainless steel AISI 304 with a polished finish. Glass: The glass used for the railing should be toughened glass with a thickness of 10mm. The glass will frosted as approved by architect.The height of the railing is 36 inches (914mm).Baluster spacing: The spacing should meet safety standards.Handrail: It should be at least 1.5 inches (38mm) in diameter made of stainless steel materials.Anchors: The railing is anchored to the floor or the side of the staircase using stainless steel anchors.

Providing material and labour for fixing suspended FALSE CEILING -made out of 12.0 mm (apprx.) thick Gypsum Plaster Boards of gyproc or equivalent made G.I standard section framework. -The G.I. Section frame work shall be tied to the roof and walls with the anchor fastener screws/bolts of appropriate size recommended by the manufacturer . -The boards shall be fixed to the frame work with the screws and the joints shall be flushed and finished with requisite jointing compounds paper tapes etc. -the ceiling will have 300mm wide plywood band will finish in 1mm thick laminate having Burma teak texture as shown in drawing. -The surface shall be finished evenly by applying putty, sand papering, applying primer & paint of approve make and type evenly complete with designer ceiling with part ply + laminate as shown in drawing -making all necessary provision and cut outs for all electrical boards, wiring, HVAC , plumbing etc. fittings, fixtures and cleanliness as per detailed design and drawing or as directed by engineer in charge. -height of false celling will be approx. 3000mm from Floor finish level, -Price shall include any ledge, grove, offset, edging in sq.mt. only. -Length X breath of false ceiling will measured for payment. as directed by Engineer-In-Charge etc. complete. (RA)

Providing and fixing in true horizontal level FALSE CEILING with metal sheet 2mm in -grid system manufactured by M/s. Armstrong World Industries (India) Pvt. Ltd or its equivalent -using hot dipped galvanized steel section, exposed surface chemically cleaned capping prefinished in backed polyester paint wall angle used in periphery of the ceiling fixed to the wall/partition/RCC column/band walls with the heip of screws -Main runner of size appropriate size suspended at specfied distaance c/c by using G.I. wire or any other hanger securely fixed to the structural member by using anchor fastener. long cross tee to be interlocked between in main runner to form grid as per architectural design. -and finally fixing metal ceiling of size as per drawing or as approved by engineer-in-charge -height of false celing shall be as per architectural drawing from Floor finish level -The rates to include cutouts for lighting fixtures / AC grilles / Fire Alarm Detectors etc., along with necessary strengthening and supports for fixing of these.

Providing material and labour for fixing suspended GRID FALSE CEILING 600x600mm -made out of 12.0 mm (apprx.) thick Calcium silicate Boards of gyproc or equivalent made G.I standard section framework. -The G.I. Section frame work shall be tied to the roof and walls with the anchor fastener screws/bolts of appropriate size recommended by the manufacturer . -The boards shall be fixed to the frame work with the screws and the joints shall be flushed and finished with requisite jointing compounds paper tapes etc. -the ceiling will have 300mm wide plywood band will finish in 1mm thick laminate having Burma teak texture as shown in drawing. -The surface shall be finished evenly by applying putty, sand papering, applying primer & paint of approve make and type evenly complete with designer ceiling with part ply + laminate as shown in drawing -making all necessary provision and cut outs for all electrical boards, wiring, HVAC , plumbing etc. fittings, fixtures and cleanliness as per detailed design and drawing or as directed by engineer in charge. -height of false celling will be approx. 3000mm from Floor finish level, -Price shall include any ledge, grove, offset, edging in sq.mt. only. -Length X breath of false ceiling will measured for payment. as directed by Engineer-In-Charge etc. complete. (RA)

Providing and fixing UPVC fins for cladding or as part of building façade systems in approved colur & specifications for UPVC fins with dimensions of 50mm x 50mm: 1 Material - Type: Unplasticized Polyvinyl Chloride (UPVC) - Density: Typically ranges between 1.3–1.45 g/cm³ - UV Stability: Must be UV stabilized for outdoor use to prevent degradation under sunlight 2. Dimensions - Width: 50mm - Height: 50mm - Thickness: 3mm - SPACING : 50mm between two fins - Length: As per architectural details 3. Physical Properties - Tensile Strength: Generally around 40–55 MPa - Impact Resistance: High impact resistance - Flexural Strength: 60–80 MPa 4. Installation with the necessary framing work shall be part of scope of work. - Fixing: on ms framing with appropriate UPVC-compatible fixings such as screws, bolts, etc. 6Kg/Sqm MS framing shall be considered for quoting. All other techincal details as directed by engineer-in-charge

Providing and fixing 600mm x 450mm bevelled edge Mirrror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden pluge with C.P. brass screws and washers.

Providing material and supply Toilet Dustbin having specifications: Materials:- - Body: High-density polyethylene (HDPE) - Lid: Plastic with a foot pedal for hands-free operation Dimensions: - Height: 60 cm - Diameter/Base Width: 40 cm - Capacity: 15 liter Design Features: - Shape: Round or rectangular design to fit in various bathroom spaces. - Color Options: Neutral tones (white, gray, black) or customizable finishe. FootPedal: - Durable plastic and other specification as directed by engineer-in-charge.

Providing material & labour for fixing Sand blasted pre-cast concrete High Strength High Finish (HSF) paver block 80mm thick as per design of any shape/any size with percentage of water absorption not more than 6%, compresive strength not less than 350 kg/Sqm. Tensile splitting strength (as per EN 1338) not less than 3.6 Mpa any colours as per approved design including 75mm Sand bedding layer for levelling and filling the joint with sand in proper line and level. The paver block should be strong enough to take heavy traffic load. The sand bed should make up for all the undulations and give a leveled surface. A mechanical compactor shall be used for compacting the sand base. All this should be in line with the manufacturer's specifications and the Engineer's directions. The final surface should be swept clean of all dust and sand to get uniform and smooth riding surface. Area of Block laid to be measured for payment etc complete. Make:- Vyara and Supertiles or equivalent.

Providing and fixing pre-cast concrete kerb stone of gray cement based concrete block 60cm length,30cmheight and 15cm thick of M250 grade concret as per approved design and includingexcavation for fixing in proper line and level,filling the joint withC:M 1:3 (1cement:3fine sand) etc complete.

Providing material and labor for GARDEN SOIL:- Supplying on site garden soil well sieved 90% to pass through I.S. sieve of 10mm size free from stones rubbish like dried grass roots and other such materials. The soil should be ftesh from quarry. The colour of the soil generally be red. The soil will be measured by measuring box.(Farma) (Item includes Royalty charges,, Transporting, Ioading unloading etc.) lead charges for 30 k.m. is considered.

Providing material and labor FARM YARD MANURE : Supplying on site well decayed, well dried, well powdered, without clods and free from stones, dried grass and other rubbish material. The colur of the manure generally be black. The manure will be measured by measuring box. (Farma) (Item includes Transporting, loading unloading etc.) lead charges for 20 km is considered.

Providing labour for MIXING GARDEN SOIL/SILT & MANURE THROUGHLY WELL, Watering Pervious night, Planting required plant species, lawn gress as dricted etc. complete.

Providing material and labor for LAWN :- Supplying and planting reuired variety of lawn grass as directed and maintaining till well established by watering, weeding clipping, rolling etc. complete.

Providing material and labor for TREES:- (minium height to 3 mtr.):- digging pit with size 0.9mx0.9mx0.9m removing and conveying unwanted stuff to a required stuff to a required distance as directed. Filling the pit with approved excavated material up to a height of 0.30m. And remining height of 0.60m with fresh garden soil and manure in 3:1 proportion . mixing soil and manure thoroughly well, levelling, as directed , watering previous night, planting two to three year old , minimum 2.0 mtr. height , healthy trees sapling as per specification. maintaining till well established by watering , weeding, stirring of soil staking replacing of casualties etc. complete.

Providing material and labor for TREES:-( height to 1.5 mtr.):- digging pit with size 0.9mx0.9mx0.9m removing and conveying unwanted stuff to a required stuff to a required distance as directed. Filling the pit with approved excavated material up to a height of 0.30m. And remining height of 0.60m with fresh garden soil and manure in 3:1 proportion . mixing soil and manure thoroughly well, levelling, as directed , watering previous night, planting two to three year old , minimum 2.0 mtr. height , healthy trees sapling as per specification. maintaining till well established by watering , weeding, stirring of soil staking replacing of casualties etc. complete.

TREES:-Supply and erecting Morpankhi Hedges (minium height to 2.5 mtr)- digging pit with size 0.9mx0.9mx0.9m removing and conveying unwanted stuff to a required stuff to arequired diatance as directed. Filling the pit with approved excavted material up to a height of 0.30m. And remining height of 0.60m with fresh garden soil and manure in 3:1 proporation . mixing soil and manure thoroughly well, levelling, as directed , watering previous night, planting two to three year old , minium 2.0 mtr. height , healthy trees sapling as per specification. maintaning till well established by watering , weeding, stirring of soil staking replacing of casualties etc. complete.

HENNA PLANTATION :- Excavting the ground to required depth of 30 cms, removing and coveying unwanted stuff to a required depth as directed. Filling fresh garden soil and manure in excavted area 3:1 poroporation to a height of 30 cms. Mixing garden soil and manure thoroughly well developed shurbs plants, 0.50 mtr. height, 0.45mtr.apart as directed and maintaining till well eastabilished by watering, weeding, stirring, replacing casualtiies etc. complete

Preparing Shrubbery :- Excavting the ground to required depth of 30 cms, removing and coveying unwanted stuff to a required depth as directed. Filling fresh garden soil and manure in excavted area 3:1 poroporation to a height of 30 cms. Mixing garden soil and manure thoroughly well developed shurbs plants, 0.50 mtr. height, 0.45mtr.apart as directed and maintaining till well eastabilished by watering, weeding, stirring, replacing casualtiies etc. complete

Providing and Installing a toddler swing, as per technical specifications mentioned below 1. Material: - Frame: - made of powder-coated steel for outdoor swings. - Must be weather-resistant and rust-proof for outdoor use. -Seat: - High-density polyethylene (HDPE) for durability. - UV-resistant for outdoor swings to prevent degradation over time. - Soft or flexible rubber/plastic material for added safety. - Rope/Chains: - Chains: Galvanized coated with rubber for safety. - Ropes: High-strength synthetic material nylon 2. Dimensions: - Seat Dimensions: - Width: 10 to 12 inches (25 to 30 cm). - Depth: 8 to 10 inches (20 to 25 cm). - Back Height: 10 to 15 inches (25 to 38 cm). - Height from Ground (Swing Clearance): - 18 to 24 inches (45 to 60 cm) for a toddler swing - Overall Swing Height: - 6 to 8 feet (180 to 240 cm) for outdoor swings. 3. Weight Capacity: - designed to hold weight 25 kg 4. Safety Harness/Belt: - Made of durable, non-toxic, and skin-friendly materials. 5. Suspension System: - Swing Type: - Full bucket seat swings for safety, with support all around the toddler. - High-back support to prevent falling backward. 6. Mounting: - Must include strong mounting brackets that can handle at least double the weight limit of the swing - Ensure it’s securely fastened when used indoors. - Outdoor A-Frame - Securely attach to the swing set with proper fittings, bolts, and washers. 8. Swing Range: - Maximum Swing Angle:around 30° to 45° to avoid dangerous high-speed swinging. - Swing Distance from Other Objects:Ensure a safe clearance of at least 6 feet (1.8 meters) in front and behind the swing. 9. Assembly: - Easy to assemble with clear instructions. - Includes all necessary tools and parts (bolts, nuts, washers, etc.). - All hardware should be rust-resistant and heavy-duty. or any other specifications as directed by engineer-in-charge or architect.

Providing and Installing an integrated play structure with climbing, swings, and slides considering safety, materials, durability, and child development standards as per technical specification mentioned below: 1. General Requirements - Age Group: Designed for children aged 3-12 years. - Capacity: Accommodates up to 10-15 children at a time. - Usage: Outdoor use, suitable for installation in public parks, schools 2. Structural Components Materials - Frame: - Material: Galvanized steel with powder coating (min. thickness of 0.2mm) - Corrosion-resistant treatment for outdoor conditions. - Decking & Panels: - Material: High-density polyethylene (HDPE) - Slip-resistant surfacing with drainage holes to prevent water accumulation. - Fasteners: All nuts, bolts, and screws should be stainless steel with tamper-proof security features. - Ropes/Netting: UV-stabilized nylon ropes, weatherproof and anti-fungal treated. Climbing Equipment - Climbing Frame: - Type: Multi-level climbing structure with a combination of ladders, ropes - Material: Powder-coated steel - Height: 2-3 meters max, suitable for the age group. - Safety: Rounded edges, no sharp corners or gaps that could trap fingers. Swing Set - Frame: - Material: Galvanized steel - Height: 2.5-3 meters. - Design: A-frame for maximum stability. Swing Chains: - Material: Galvanized steel, coated with rubber at hand level. - Anti-pinch design to prevent finger injuries. -Swing Seats: - Material: Rubber - Size: Should accommodate children comfortably (min. width: 35-40 cm). - Safety: Anti-wrap design with seat safety straps for smaller children Slide - Material: UV-resistant, high-density polyethylene (HDPE) smooth finish. - Type: - Straight or spiral slides, integrated into the climbing structure. - Length: 1.5-2.5 meters. - Width: 45-60 cm. -Safety Features: Non-slip entry point with side barriers to prevent falls. 3. Safety Specifications - Fall Zones: - Minimum clear area around the play structure should be 1.8m for climbing equipment, swings, and slides. - Use of shock-absorbing surfaces like rubber mulch, wood chips, or rubber tiles with a fall height rating of at least 2.5 meters. - Maximum Fall Height: Not to exceed 2.5 meters. - Edge Protection: All exposed edges should have rounded, soft-capped ends to prevent injury. - Load Capacity: - Each swing seat: 80 kg. - Overall play structure should support multiple children (500 kg or more total capacity). - Anchoring: Ground installation with concrete footings bolted surface mountings. 4. Environmental and Durability Considerations - UV Resistance: All plastic components should be UV-resistant to prevent degradation from sunlight. - Weather Resistance: Coatings must prevent rusting, corrosion, and cracking under varying weather conditions. 5. Design and Aesthetics - Colors: Bright, engaging colors (preferably UV-stable), with an option to customize the color scheme. - Modular Design: Ability to expand or modify the play structure by adding new elements like tunnels, bridges, or additional swings and slides. 6. Installation and Maintenance - Installation: Should be done by certified professionals, with detailed instructions for anchoring, assembly, and safety checks. - Inspection: Routine maintenance should be possible with easily replaceable parts. Inspection guidelines to be provided for safety and wear checks every 6-12 months. ### 7. **Certifications and Testing**. - Testing: The equipment should undergo load-bearing, UV, and impact testing before delivery. or any other specifications as directed by engineer-in-charge or architect.

Providing & Installing seesaw for playground equipment designed for kids, consisting of a long board balanced on a central pivot point as per the technical specifications mentioned below: 1. Materials: - Frame: - Material: Galvanized steel (rust-resistant and durable). - Finish: Powder-coated for weather resistance and enhanced durability. - Seat: - Material: High-density polyethylene (HDPE) - Padding: Soft rubber padding for seat comfort and safety. - Handles: - Material: Rubber-coated steel for good grip. - Pivot (Fulcrum): - Material: Steel, corrosion-resistant material. - Bearings: Lubricated and sealed ball bearings for smooth movement. 2. Dimensions: - Length: 8 feet. - Height of Seat (at rest): Approximately 1-2 feet (0.3 - 0.6 meters) off the ground - Seat Width: About 8-10 inches (20-25 cm) for adequate sitting space. - Handle Height: Approximately 12-18 inches (30-45 cm) above the seat for comfortable gripping. - Weight Capacity: Designed to handle between 45-135 kg per side 3. Safety Features: - Shock Absorbers/Bumpers: Rubber stoppers or springs under the seat ends to soften the impact when the seesaw hits the ground. - Non-slip Seats and Footrests: Textured or anti-slip surfaces on the seats and footrest to prevent slipping during use. - Rounded Edges: Smooth, rounded edges to prevent injury from sharp corners. - Secure Pivot System: A well-balanced pivot with no exposed sharp parts or pinch points 4. Age Appropriateness: - Age Range: Designed for children aged 3-12 years. - Maximum Users: for two kids 5. Installation Requirements: - Anchoring: Ground-anchored using concrete footings for safety and stability.. 6. Standards Compliance: - Load Testing: Must be Tested for appropriate weight loads to ensure structural integrity. Any other specification as per the direction of Engineer-in-charge or architect.

Providing material and labour for Supplying and transporting & spreading of good quality golden sand including the cost of spreading the sand, loading, unloading etc. complete. As directed by chief engineer incharge.

Providing and fixing to wall ceiling and floor 6.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(A) 20mm

Providing and fixing to wall ceiling and floor 6.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(B) 25mm

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(C) 32mm

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(D) 40mm

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(E) 50mm

Providing and fixing in position cowel went to pipes.(B) 75mm dia. (Make - Astral / Prince / Truflow or eq.)

Providing and fixing in position cowel went to pipes.(C) 100mm dia. (Make - Astral / Prince / Truflow or eq.)

Providing and fixing screw down bib taps of following size.(B) Brass chromium plated screws down Bib Tap. (i) 15mm dia. Make: Jaquar/Cera/Parryware/Hindware Or Equivalent

Providing and fixing Gun metal check or non-return fullway wheel valve.(A) 15mm dia. (Make - Sant/ Zoloto/ or eq.)

Providing and fixing Gun metal check or non-return fullway wheel valve.(B) 20mm dia. (Make - Sant/ Zoloto/ or eq.)

Providing and fixing Gun metal check or non-return fullway wheel valve.(C) 25mm dia. (Make - Sant/ Zoloto/ or eq.)

Providing and fixing Gun metal check or non-return fullway wheel valve.(D) 32mm dia. (Make - Sant/ Zoloto/ or eq.)

Providing and fixing Gun metal check or non-return fullway wheel valve.(E) 40mm dia. (Make - Sant/ Zoloto/ or eq.)

Providing and fixing ball cock of approved. quality as directed.(B) Abonite (ii) 50mm dia. (Make - Zoloto / Sant / Or eq)

Providing and fixing G.I. Rain water spout of 50mm dia. and 30cm. length.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete.[A] 15 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [B] 20 mm.

Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concealed as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials. Make: Prince/Supreme/Jain/Astral/Tulsi/Finolex or Equivalent

Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concealed as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials. Make: Prince/Supreme/Jain/Astral/Tulsi/Finolex or Equivalent

Providing laying and jointing in true line and level 32mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concealed as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials. Make: Prince/Supreme/Jain/Astral/Tulsi/Finolex or Equivalent

Providing laying and jointing in true line and level 40mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concealed as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials. Make: Prince/Supreme/Jain/Astral/Tulsi/Finolex or Equivalent

Providing laying and jointing in true line and level 50mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concealed as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials. Make: Prince/Supreme/Jain/Astral/Tulsi/Finolex or Equivalent

Providing, laying and jointing in true line and level 160 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 160 mm diametre x 210 mm length x 196 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. Make: Prince/Supreme/Jain/Astral/Tulsi/Finolex or Equivalent.

Providing, laying and jointing in true line and level 110 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. Make: Prince/Supreme/Jain/Astral/Tulsi/Finolex or Equivalent

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm diameter with jali of the following nominal diameter of self cleansing design with C.I scread down or hinged grating including the cost of cutting and making good the walls.

Providing erecting and fixing double coated ISI water tank of required capacity each with all necessary fittings and connection etc. complete on terrace. Make: Sintex/Orient/Aqua safe or Equivalent.

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I. cover with frame of 300mm x 300mm size (inside) with standard weight.(i) Square mouth traps. (A) 100mm x 100mm size P type.

Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-pressure pipes I.S. class NP2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete.(B) 150mm (Make - Indian / Pranali or Eq.)

Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-pressure pipes I.S. class NP2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete.(C) 250mm (Make - Indian / Pranali or Eq.)

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1- cement :2-coarse sand : 4-graded stone aggregate 20mm nominal size) foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick with Cement Mortar 1:3 (1- Cement : 3-coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1 Cement :2-Coarse sand :4-stone aggregate 20mm nominal size) finished smooth complete including curing and festing (i) Inside size 900mm x 1200mm and 1.5M. deep including C.I. cover with frame size 560mm diameter total weight of cover and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (1) A type depth 0.90 Metre for 150mm diameter sewer.

(I) Extra rate for constructing B.B. masonry for every additional depth of 0.1M. or Part thereof over item No.24.27 (I) for depth from 0.9M to 1.5M.

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1- cement :2-coarse sand : 4-graded stone aggregate 20mm nominal size) foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick with Cement Mortar 1:3 (1- Cement : 3-coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1 Cement :2-Coarse sand :4-stone aggregate 20mm nominal size) finished smooth complete including curing and festing (i) Inside size 900mm x 1200mm and 1.5M. deep including C.I. cover with frame size 560mm diameter total weight of cover and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (2) B type depth 1.50 Metre for 150mm diameter sewer.

(II) Extra rate for constructing B.B. masonry for every additional depth of 0.1M. GR Part thereof over item No.24.27 (I) for depth from 1.50M. to 2.25M.

Providing and fixing cast iron steps of size 500mm x 150mm x 22.5mm and painting with two coats of Anti corrosive paint etc. complete.

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with bricks having crushing strength not less than 35Kg/Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1 cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(i) Inside dimensions 455mmx 610mm and 450mm deep for single pipe line.

Extra over items 24.44 for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(i) for 455mm x 610mm size.

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with bricks having crushing strength not less than 35Kg/Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(ii) Inside dimensions 500mm x 700 mm and 450mm deep for pipe line with one or two inlets.

Extra over items 24.44 for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(ii) for 500mm x 700mm size.

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with bricks having crushing strength not less than 35Kg/ Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1 cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(iii) Inside dimensions 600mm x 850 mm and 450mm deep for pipe lines with three or more inlets.

Extra over items 24.44 for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(iii) for 600mm x 850mm size.

Providing and fixing on platform stainless steel Sink glossy ASIS 304 grade x 1mm thick with over all size 610x460mm & bowl size 560x410x200mm & SS Pillar cock with extention body like JAQUAR FUS-CHR-29021N including fixing the sink in platform & making good the same including the cost of PVC waste pipe of 32mm dia. and PVC waste coupline etc complete as directed by EIC.

Providing and fixing Two way BIB cock with wall flange of genuine Jaquar ompany brand, in with model no FUS-CHR29041, water tap brand or approved ISI brand quality, fixing in pieline and testing the same… etc., complete., as directed by EIC

Providing and fixing wash down water closet European type WC pan (Wall Hung) like JAQUAR CNS-WHT-961SPP- SIZE 365x545x360MM and P trap distance 23.5 cms with integral P trap including jointing the trap with soil pipe in cement mortar 1:1 (1 cement : 1 find sand) including providing and fixing of 1) Health Faucet hand shower heavy duty with SS braided hose 1.2 MT long pipe to water closet - JAQUAR ALD-CHR-573 with Single Piece Slim Concealed Cistern Body with Installations Kit & “S-Type” drain pipe connection set for Wall Hung WC (without Flush Control Plate) - JCS-WHT-2400S with Control Plate Opal - JCP-CHR-152415,Toilet roll holder -Jaquar -ACN -1151N etc,complete Make:-Jaquar/Cera/Parryware/Hindware or Equivalent

Providing and fixing Wash Basin vitreous china table top wash basin size 560mm x 450 mm in white colour. Like JAQUAR CNS-WHT-903 SIZZE OF 425x340x175MM with single hole for pillar tape with CP or MS brackets painted white including cutting holes and making good the same including (1) Providing and fixing SS waste coupling of 32 mm dia size half theread with 80mm height like jaquar -ALD - CHR-705 for wash basin with rubber plug (2) Providing and fixing SS bottle trap with internal partition of 32mm size with 250mm &190mm long wall flange connection pipes and wall flange likejaquar ALD-769 L250X190 of approved quality with necessary fitting for wash basin (3) Providing and fixing SS Pillar cock with extention body like JAQUAR FUS-CHR-29021N with necessary fittings etc. complete (4) Providing and fixing SS finish Angular Stop Cock quarter turn like Jaquar code FUS-29053 with necessary fittings (5) Providing and fixing SS finish soap dispenser with metallic bottle like Jaquar code-ACN-CHR-1135N,Towel ring -jaquar-CAN-1121BN etc. complete. Make: Jaquar/Cera/Parryware/Hindwareof Equivalent

Providing and fixing Urinal of approved quality including connection with trap and with integral longitudinal flush pipe.(A) Squating plate pattern white earthenware size of urinal 370mm x 315x 620 mm.of jaquar make code no URS -WHT-132530 including (1) Providing and fixing SS finish waste coupling of 32 mm dia size half theread with 80mm height like jauar -ALD - 709 for wash basin with rubber plug (2) Providing and fixing SS finish bottle trap with internal partition of 32mm size with 250mm &190mm long wall flange connection pipes and wall flange like jaquar ALD-769 of approved quality with necessary fitting for wash basin (3) SS finish flush valve of auto closing system like jaquar PRS-073 of approved quality and connection with waste pipe trap etc. complete. Make: Jaquar/Cera/Parryware/Hindware or Equivalent

Providing and fixing U PVC SCH40 for cold water 20 mm dia (3/4)"

Providing and fixing PVC SWR pipes IS 13592 for Drain - 75 mmdia

Providing and fixing PVC SWR P- Trap IS 14735 for Drain -110x110

Providing and fixing Gun metal check or non-return fullway wheel valve. (A) 50mm dia. (Make - Zoloto / Sant / Or eq)

Providing laying and jointing PVC SWR pipes IS 13592 for Drain - 50 mmdia it's accessories.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing and fixing SS finish Angular Stop cock for wash basin like Jaquar code FUS-29053

Providing laying and jointing in true line and level 65mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concealed as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials. Make: Prince/Supreme/Jain/Astral/Tulsi/Finolex or Equivalent

Providing and fixing Gun metal check or non-return fullway wheel valve. (A) 65mm dia. (Make - Zoloto / Sant / Or eq)

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length , in below type of pipe erected with 6A Modular type switch / bell push & accessories and earth continuity of following type, erected on PVC / Metallic/Wooden box, single mounting base frame covered with textured/metallic/white front plate modules erected on / in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed. (f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete cat III

Point wiring for Tissino / Modular secondary light point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires, in below type of pipe to be erected complete with earth continuity and necessary connection with primary light with accessories erected on Metal / PVC / wooden box covered with 3 mm thick PC(Polycarbonate) / Acrylic sheet for open / concealed wiring. with necessary Lamp holder / ceiling rose / H.D.Connector as directed. Note:- Maximum up to 6 mtrs length, excess will be considered as Mains for Secondary Point. (f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete cat III

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe erected with 6A Modular type switch and hum free EME step type electronic fan regulator mounted and accessories with earth continuity of following type erected on PVC / Metallic/Wooden box, single mounting base frame covered with textured/metallic/white front plate modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed. (f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete cat III

Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (green) both are of .ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires erected in below type of pipe with 6A Modular type switches and following type of accessories erected on PVC / Metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate modules erected on / in wall / ceiling as per pipe erected. with necessary batten/angle holder or ceiling rose or H.D.Connector as directed. (f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe erected complete with Modular type switch & 5 pin Plug erected on PVC / Metallic/Wooden box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories [II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu. Wire from mcb db board. (f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete cat III

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe erected complete with Modular type switch & 5 pin Plug erected on PVC / Metallic/Wooden box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories. [I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire from nearby switchboard/mcb db board (f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete

Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate modules erected on / in wall / ceiling with following type accessories Cat. III

Providing & erecting Switch board for Computer or electric apparatus consisting of following modular type accessories mounted with PVC / Metallic concealed/open box with single mounting base frame covered with textured/metallic /white front plate,modules erected with necessary connections as directed 1 no. 6A/16A universal plug-switch combined. 3 nos. 6A Switch 3 nos. 6A 5 pin Plug For Modular Type Accessories Cat. III

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate , modules erected with necessary connections as per site situation directed by Engineer In charge. (8) Computer RJ-45 socket Cat.III

Supplying & erecting approved make LAN cable of following size in existing pipe as per direction [D] CAT - 6 e

Supplying & erecting approved 24 port gigabyte unmanaged switch.

Supplying & erecting access point with POE.

Supply,Installation,Testing and Commissioning of Table mount Modular Multi-connection Cable Manager Should have an easy openable retractable lid which disappears with a single tap of a button.

SITC of Patch Panel Cat 6 UTP Keystone Type- 24 Port-Fully Loaded (Including Five year free maintenance with guarantee)

SITC of CAT6 UTP 24AWG PATCH CORD:1M,Plug 30U' Snag less [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]

SITC of CAT6 UTP 24AWG PATCH CORD:2M,Plug 30U' Snag less [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]

Providing & Erecting Netwrok rack with following capacity with Necessary cooling fan,Cable manager,6A PDU,equipment rack with necessary mounting accessories. (A) 9 U

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate , modules erected with necessary connections as per site situation directed by Engineer In charge. (3) Two Pin/RJ-11 Telephone Socket [A] For One Gang Cat.III

Supplying & erecting approved make Telephone Cable electrolytic copper conductor PE insulation twisted in two pairs, & wrapped with FRLS PVC tape & sheathed with FRLS PVC or HFFR outer Jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe. of following size of conductors & nos.of pairs. With necessary connections. [A] Conductor Size 0.5 mm (a) Unarmoured (2) Two Pairs

Providing & erecting main Distribution (MDF) indoor type, back mounted frame as per DoT standard approved with krone strips (c) Suitable for 50 pair

SITC of Digital / PCM / TDM EPABX System having SMT design, system with flexible universal slots. Inbuilt Auto attendant facility, Minimum 15 Nos. conference, Analog extension line, Calling GSM, E&M line, PRI / EI & VOIP program me through Analog telephone digital key from Ethernet, public address cord, shall have unrestricted simultaneous dialing facility, QSIG protocol on PRI, 95 / STD / ISD / Local-Locking, Class of Service, Quick Dial-Single Digit dialing of any two external number, Once only ring device, Chairman / Secretary - Do not disturb Facility, Power Down Mode, Hot Line, Hot Outward Dialing, Day Night Mode, Auto Call Back, Barge-in, Call Pick Up & Call Transfer, Call transfer while Ringing with Voice Guide System, (DISA), Caller ID (CLI), CLI Base ECF, CLI Base routing Internet Ready Port, External Music Port, Call Budgeting, Call Most Calculation (ASMDR), DID Direct Inverse Dialing, External Music Input, Fax Homing, Global Directory Printing with following capacities [[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] [B] No of Extension 24, No of Junctions 9, 8 Port IP Resource in-built, 4 Port Web base Video Conferencing, No of expandable ports : 96, Operators Console - 01 Compatible : ISDN

providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 erected in existing pipe of following size (Specifically for control panel, relays, power switchgears, motor starters & control wiring) with required size of copper lugs, nuts and bolts if required. (f) One wire 10.00 sq. mm

providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 erected in existing pipe of following size (Specifically for control panel, relays, power switchgears, motor starters & control wiring) with required size of copper lugs, nuts and bolts if required. (g) One wire 16.00 sq. mm

providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 erected in existing pipe of following size (Specifically for control panel, relays, power switchgears, motor starters & control wiring) with required size of copper lugs, nuts and bolts if required. (h) One wire 25.00 sq. mm

providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 erected in existing pipe of following size (Specifically for control panel, relays, power switchgears, motor starters & control wiring) with required size of copper lugs, nuts and bolts if required. (i) One wire 35.00 sq. mm

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size. (A) With medium class Rigid PVC pipe and accessories (a) 2 wire 1.5 sq. mm

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size. (A) With medium class Rigid PVC pipe and accessories (b) 2 wire 2.5 sq. mm

providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size(A) With medium class Rigid PVC pipe and accessories (a) 2 wire 4 sq. mm

providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size(A) With medium class Rigid PVC pipe and accessories (c) 2 wire 10 sq. mm (use earth wire of 4 sq.mm )

providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size(A) With medium class Rigid PVC pipe and accessories (g) 4 wire 4 sq. mm

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as directed (b) 25 mm

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts etc. complete of following sizes.(2) 25 mm

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) suitable for (A) single phase incoming and horizontal single phase outgoing (b) sheet steel double door (IP-43) (ii)6 way

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) suitable for (A) single phase incoming and horizontal single phase outgoing (b) sheet steel double door (IP-43) (iii)8 way

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) suitable for (B) three phase incoming and single phase horizontal type outgoing Per phase isolation type (PPI) (b) sheet steel double door (IP-43) (i)4 way

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) suitable for (B) three phase incoming and single phase horizontal type outgoing Per phase isolation type (PPI) (b) sheet steel double door (IP-43) (ii)6 way

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) suitable for (B) three phase incoming and single phase horizontal type outgoing Per phase isolation type (PPI) (b) sheet steel double door (IP-43) (iii)8 way

providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark Cat.III

Providing & erecting 240 V MCB double pole switch for lighting Load (B Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity (A) 6 to 32 Amp. Cat-III

Providing & erecting 240 V MCB double pole switch for lighting Load (B Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity (B) 40 Amp. Cat-III

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity (a) 6 to 32 Amp. Cat III

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity (b)40 Amp. Cat.III

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity (c)63 Amp. Cat.III

providing and erecting Approved make RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and suitable for operation on single phase 240 V,50Hz. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed (i) 25 Amps.DP Cat. III

providing and erecting Approved make RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and suitable for operation on single phase 240 V,50Hz. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed (ii) 40Amps. DP Cat. III

providing and erecting Approved make RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and suitable for operation on single phase 240 V,50Hz. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed (iii) 63 Amps. DP Cat. III

Supplying and erecting triple pole & neutral 440V / 500V panel mounting Copper Busbars with four equal Nos. of electrolyte bus having current density not more than 1.6 Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour insulating tape for phase sequence of following current carrying capacity, erected with necessary bus bar supports /insulators, main cable socket to each bar, erected in existing cubical panel with necessary connections. (A) Suitable for 100 Amp. Capacity

Supplying and erecting triple pole & neutral 440V / 500V panel mounting Copper Busbars with four equal Nos. of electrolyte bus having current density not more than 1.6 Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour insulating tape for phase sequence of following current carrying capacity, erected with necessary bus bar supports /insulators, main cable socket to each bar, erected in existing cubical panel with necessary connections. (B) Suitable for 200 Amp. capacity

Supplying and erecting triple pole & neutral 440V / 500V panel mounting Copper Busbars with four equal Nos. of electrolyte bus having current density not more than 1.6 Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour insulating tape for phase sequence of following current carrying capacity, erected with necessary bus bar supports /insulators, main cable socket to each bar, erected in existing cubical panel with necessary connections. (D) Suitable for 400 Amp. capacity

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 25 KA. at 415 V,having normal current rating up to 25 A to 100A. with Fixed thermal & magnetic release suitable to work on A.C. supply 50 c/s. with all internal connections, spreader tinned copper & complete erected in existing 16 G.M.S. housing.

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 35 KA. at 415 V. having normal current rating 125A. with Fixed thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all internal connections, spreader tinned copper & complete erected in existing 16 G.M.S. housing.

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 35 KA. at 415 V. having Normal current rating 200A.with variable Thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all internal connections, spreader tinned copper & complete erected in existing 16 G.M.S.housing

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 50 KA and above at 415 V having Normal current rating 400A. with variable Thermal & magnetic release suitable to work on A.C.supply 50 c/s. With all internal connections, spreader tinned copper & complete erected in existing 16 G.M.S. housing. Cat III

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 50 K.A. and above at 415 V having normal current rating up to 630A. with variable thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all internal connections, spreader tinned copper & complete erected in existing 16 G.M.S. housing Cat III

Supplying & erecting approved make Four Pole 415V change over switch interior for panel mounting with operating mechanism A.C.23 duty confirming to IS for (G) 630 A. Cat.III

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor type cubical panel board necessary IP- 42 and above protection as per approval from engineer incharge made from 14 SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for internal partitions with necessary accesories , supporting angles/ flats channel including cutting, bending, drilling, welding, riveting with internal partitions & cable alley as per requirements & instruction of engineer-in- charge with erection of supplied switch gears, BUSBARS, suitable size of inter connecting PVC copper wire / copper-aluminium strips, rubber grommets, rib, bakelite control fuses/MCB for measuring instruments, earth bus & earth bolts, foundation flange - bolts-base Plates, sufficient nos. of hinged doors, handles with locking arrangement and rubber gasket,heavy duty end terminal connection,danger notice board,necessary ventilation,earthing strip complete. The Panel shall be painted with epoxy powder coating (The rates excludes the cost of switchgears, bus bars, inter connecting mains & Copper Aluminium strips, meters, Fuses etc. The dimension shall be measured excluding base beams) The panel shall be supplied with following approved manufacturers with following size. (B) The standard companies switch gear shall be used and only manufacturers at CPRI approved factory. (i) with 350mm depth board

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor type cubical panel board necessary IP- 42 and above protection as per approval from engineer incharge made from 14 SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for internal partitions with necessary accesories , supporting angles/ flats channel including cutting, bending, drilling, welding, riveting with internal partitions & cable alley as per requirements & instruction of engineer-in- charge with erection of supplied switch gears, BUSBARS, suitable size of inter connecting PVC copper wire / copper-aluminium strips, rubber grommets, rib, bakelite control fuses/MCB for measuringinstruments, earth bus & earth bolts, foundation flange - bolts-base Plates, sufficient nos. of hinged doors, handles with locking arrangement and rubber gasket,heavy duty end terminal connection,danger notice board,necessary ventilation,earthing strip complete. The Panel shall be painted with epoxy powder coating (The rates excludes the cost of switchgears, bus bars, inter connecting mains & Copper Aluminium strips, meters, Fuses etc. The dimension shall be measured excluding base beams) The panel shall be supplied with following approved manufacturers with following size. (B) The standard companies switch gear shall be used and only manufacturers at CPRI approved factory. (iv) with 1000 mm. depth

Providing , erecting , fabricating the M.S. structure as per requirement on site incorporating proper size of M.S. angles,square,round, flats, bars, channels, sections complete with cutting, welding, grinding & finishing duly painted with one coat of red oxide with erection on site as per direction of engineer in charge with necessary grouting, cementing, plastering & finishing complete.

Providing & erecting approved make AMF control panel suitable for following size of 3 phase, 415 V., 50 cycles, A.C. diesel generating set complete of scope as detailed below: 1) Power module: A pair of electromechanically interlocked contactors (for mains & generator) Overload relay for generator contactor Neutral contactor for mains and generator Power socket for connections. 2) Control and metering module: Line voltage monitor. Generator voltage monitor Ammeter 3 items attempt start facility. Air circuit breakers/MCB/MCCB of suitable rating for auto/manual operation. Auto/manual switch. Emergency stop push buttons. Manual start push button. frequency meter. Engine hour meter. Two earthing studs. 3) Protection module: The engine shutdown in the unlikely event of Low lube oil pressure High cylinder head temperature. V belt failure. 4) Indicators with alarm Load on generator. 5) Indicators Load on mains Engine fails to start . Emergency stop battery charger. The AMF Panel of following capacity (D) AMF Control Panel for200 KVA/250 KVA3 phase DG Set

Providing and erecting multifunctional meter suitable for application of Power monitoring and showing measurement of following Voltage, Frequency, Apparent energy, Apparent power, Active and reactive energy, Active and reactive power, Average voltage Vavg, Peak demand power PM, QM, SM, Demand power P, Q, S, Apparent power S, S1, S2, S3, Unbalance current, Power factor and displacement PF (signed, four quadrant), Calculated neutral current, Active, reactive, apparent energy (signed, four quadrant), Active power P, P1, P2, P3, Voltage U21, U32, U13, V1, V2, V3, Phase currents, Average current Iag, Peak demand currents, Reactive power Q, Q1, Q2, Q3, Demand current I1, I2, I3, [Us] rated supply voltage 40...300 V AC 45...65 Hz, 40...300 V DC, Network frequency 50 Hz, Type of network 3P, Display type 7 segments LED, Display colour Red, Messages display capacity 3 fields of 4 characters, Display digits 12 digit(s) - 14.2 mm in height

Supplying and erecting approved make suitable panel indicator LED type lamp, lens cover, complete erected with necessary connections.

Providing & erecting L.T. Current Transformer with bar primary 50/5 to 1000/5 ratio 15 VA burden erected in existing CRCA box duly secured with insulating materials connected to the meter.

Providing and erecting metallic vitrified danger notice board as per language suggested by engineer incharge for MEDIUM VOLTAGE installation to be erected as per IS-2551.

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate , modules erected with necessary connections as per site situation directed by Engineer In charge. (7) Blank Plate Single

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables. (C) 3 core 6 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (B) 3 1/2 core 35 Sq. mm ( 16 Sq. mm 1/2 core)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (C) 3 1/2 core 50 Sq. mm ( 25 Sq.1/2 mm core)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (F) 3 1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (I) 3 1/2 core 240 Sq. mm( 120 Sq. mm 1/2 core)

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand / Solid Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (B) 4 core 6 Sq. mm

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand / Solid Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (C) 4 core 10 Sq. mm

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (A) 4 core 16 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. (B) 2 to 4 core 6 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. (C) 2 to 4 core 10 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. (D) 2 to 4 core 16 Sq. mm

Providing and, fixing heavy duty flange type brass double compression type cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. (B) 3 & 1/2 core 35/50 Sq. mm

Providing and, fixing heavy duty flange type brass double compression type cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. (E) 3 & 1/2 core 120 Sq. mm

Providing and, fixing heavy duty flange type brass double compression type cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. (H) 3 & 1/2 core 240 Sq. mm

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (A) 1.5/ 2.5/4/6 Sq.mm

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (B) 10 Sq.mm

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (C) 16/25 Sq.mm.

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (D) 35/50 Sq.mm.

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (G) 120 Sq.mm.

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (J) 240 Sq.mm.

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications with chamber and heavy duty cover. (A)(approved make OEM has to submit test certificate including value of earth resistance of installation duly stamped and signed by agency and officer Incharge has to ensure the value of earthing resistane mentioned in test Certificate) & having back filling compound of (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C) Back fill Compound :- Earthing compound should be capable to retain moisture for long time Necessary test report must be submitted by Agency. (c) For Electrical Installation covering Transformer Neutrals, Lightning arrester Earthing, A.C.Plant & Sensitive Computer System(like Automation, SCADA) i.e independent Earthing in normal soil. Length of Pipe : 3.00 mtrs Back filling Compound :2 nos Bags of 25 Kg.

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board, Motors etc. using proper clamp.

Providing and erecting required size Copper strip for earthing of H.T. OCB / ACB/ Transformer, LT panel board, Motors etc. using copper clamp.

Providing and erecting Annealed bare Copper wire 8 to 16 SWG.

Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan with double ball bearing ISI mark with Condenser 230 volt A.C. 50 Hz 1200 mm sweep complete having 3blades with aluminium blades with , canopy & 30 cm. down rod erected with earthing.(Make shall be approved by Engineer in charge))

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly painted for fan complete with proper insulation without leakage and earthing.

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC bars up to 50mm length each side and pierced through a 16 Gauge M.S. box / Heavy Duty PVC box complete erected concealed in Ceiling with necessary finishing.

Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box.

Supplying & erecting approved make low noise decorative exhaust fan having square frame ABS body with inbuilt lowers & square frame. 200mm with 1350RPM Cat.II

Providing recess in wall or window frame suitable for erection of Exhaust fan complete with plastering and colour washing to match the colour of the wall or window complete with expanded metal in order to render the fitting in accessible and the room water-proof.

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate , modules erected with necessary connections as per site situation directed by Engineer In charge. (11) 6 Amps. Bell Push

Supplying & erecting Approved make call bell indicator with buzzing sound and Red light indicating lamp with Red light button to attend the call suitable for 240 v 50 c/s supply to be erected.

Supplying and erecting led lamps with following wattage capacity of 220 to 240 voltage, minimum 15000 burning hours life, 500 V in built-surge protection,Polycarbonate diffuser, mounting suitable for E14 / E27 / B22 lamp holders, pf >= 0.5 (A) LED Lamps integral type, with PC diffuser suitable LAMP holder (ii) 5 to 8 watts CAT III

Supplying & erecting recess wall mounting speaker with 5W rated input power 3.3 K. Ohms / 3W impedance, 100 - 10000 Hz frequency response with 6 inch dia. cone type 8 ohms speakers duly fitted in ABS plastic cabinet of colour match with wall or ceiling of following size. [[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] (b)Square shaped 260 x 260mm size speaker

Supplying & erecting Amplifier having following specification: Power Output :250W (RMS) (300W Max.) inputs : 6 Misc. & 2 Aux. frequency Response :50-1500HZ I3db Tone Controls :Cut & Boost type LED Meter :5 LED Arrays The amplifier suitable to operate 240V A.C.& 24volt D.C. (Battery) with automatic changeover from AC to Battery operation, duly protected by wrong Battery Polarity connections. [[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]

Supplying, erecting & testing Approved make Microphone for announcement, speech & general P.A. application with frequency response of 150 - 10000 Hz having sensitivity 2mv/Pa, & impedance 600 Ohms supplied with quick detachable holder, 6 mtr twin core cable & PCIM / MCIF connector. [[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]

Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv grade ISI marked copper wires of following size to be erected as directed. (d) 1.50 Sq.mm 2 core round PVC sheathed

Providing & erecting water cooler having storage capacity 150 Ltr. & cooling capacity 150 Ltr.per hour @ an ambient temp of 45˚ C. The outlet temp. of the water should drop by 15˚C within a hour, The water cooler should be comprising of hermetically sealed compressor, fan motor, condensing unit, water tank surrounded by evaporating, coil, thermostats, relay etc.complete with necessary inlet & outlet connection. The body of water cooler will be made from Stainless Steel.

Supplying & erecting reverse osmosis (RO) water purification system with M.S. powder coated pedestal frame, prefilter housing carbon filter suitable buster DC pump, auto low & high pressure switches with following size of LPH capacity & erected as directed [F] 500 LPH with 3 phase Raw water pump of 1000LPH @ 3.0 kg/cm2 (1No - Kirloskar /CRI /Lubi), Dual media filter 13"x54" - (1No), Micron catridge filter 20" x 4.0"-1No, High pressure pump 1000LPH @ 11kg/cm2 - (1No - lubi/ Shimge/ CRI), RO Membrane housing with RO membrane of 40*40 - (2 Nos), RO pressure tube 4" x 2E -(1No), 0-2400 LPH Rotameter ( 2Nos), , Dosing pump 0 -6 LPH - (1 No),. with 100 Ltr Dosing tank - (1 No), with Recovery Rate 50%.

S.I.T.C. submersible pump set suitable for bore of 100 mm. dia. or more having three phase motor capacity not more than 5 H.P. with following capacity . Lifting and Lowering taken extra. (B) (16 stage) 140 to 180 LPM discharge at 96 to 69 mtrs. head respectively suitable for 50mm dia. delivery pipe cat III

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper cable approved make of following Size. (C) 3 Core x 4 Sq. mm

Providing & erecting open well type horizontal mono block pump set with stainless steel body having following specification (C) 1 H.P. single phase open well motor pump set suitable for 185 LPM discharge @ 25 mtr. head, suitable for 32 mm dia. Delivery pipe with control panel. Cat II

Providing & erecting open well horizontal mono block pump set with cast iron body, complete for three phase submersible motor having [A] For 1.5 HP 3 phase open well horizontal mono block pump set suitable for 190 LPM @ 20 mtr head suitable for 40 mm dia delivery pipe Cat II

Providing & erecting open well horizontal mono block pump set with cast iron body, complete for three phase submersible motor having [C] For 3 HP 3 phase open well horizontal mono block pump set suitable for 85 LPM to 270 LPM @ 11 mtr to 33 mtr head suitable for 50/65 mm dia delivery pipe Cat II

Supplying & erecting approved make Automatic liquid level controller 6A. with sensor testing as per instruction of Engineer in charge on site complete with wiring connection with existing wires , with copper conductor from pump to upper and lower tank.

Supplying & erecting approved make motor control cubical panel [Star delta] made from 16G CRCA sheet duly epoxy powder painted inside and outside with hinged doors and locking with suitable size of ON - OFF isolator (AC 3 / 23 duty) main fuses. Digital volt and current meter (in a single unit) with micro controller based control unit and current sensing single phasing preventer electronic overload protection, over voltage (Programmable) protection and under voltage (Programmable) protection, prod less dry run protection programming facility for setting of all parameter like overload current, high voltage limit, low voltage limit, dry run limit with digital indication on seven segment LED display for any fault like over load, high voltage, low voltage, dry running single crimped, electronic star delta timer, feather touch start / stop push buttons to be erected on angle iron frame. Grouted on wall the contactors will be of L& T, Siemens, BCH make only) (A) DOL up to 5.0 H.P.

Supplying and erecting approved make Conical Pole (Standard ) Made from HR sheet steel. The pole should be made as per IS. and shall be coated with hot dip galvanizing as per IS 2629/2633/4759 with required base plate and integral Junction box consist of terminal plate of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and arrangement for cable terminationas erected on suitable foundation (included) with necessary nut-bolts/J-Bolts. as per details given by manufacturer considering site requirement.The length of poles are as below. (E) 7 Mtr. Long 65mm Top X170 mm bottom dia, 3mm thickness.

Supplying and erecting approved make Conical Pole (Standard ) Made from HR sheet steel. The pole should be made as per IS. and shall be coated with hot dip galvanizing as per IS 2629/2633/4759 with required base plate and integral Junction box consist of terminal plate of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and arrangement for cable terminationas erected on suitable foundation (included) with necessary nut-bolts/J-Bolts. as per details given by manufacturer considering site requirement.The length of poles are as below. (J) 12 Mtr. Long 70mm Top X250 mm bottom dia, 3mm thickness.

Providing and erecting street light pole bracket comprising main B Class MS pipe of 4.2 cm/require outside dia. complete with suitable B Class M.S. sleeve tubing of approx. 45cms.length and suitable for 76.5 mm / 80mm. / require size pole top having sufficient fasteners for fixing the brackets and having spread of 1 mtr. length with suitable rise as per site condition & suitable welded stiffener reducer and nipple with check nut complete painted with one coat of Red oxide / PU base primer and two coats of Aluminium / PU paint. paint with following nos of arms. [A] Single Arm bracket 1 Mtr

Supplying & erecting approved make SMC press moulded composite FRP. loop-in, loop-out approx. 2mm thick box complete with Bakelite connector strip 5way(3P+N+E),DIN rail for mounting mob & hinged doors as per requirement having locking arrangements with mounting clamp with nuts, bolts & washers suitable for erection on pole with cable clamps& earth bolt of following size of box. (A) 300mm x 200mm x 100mm [deep]

(b) LED Bollard fittings of minimum height 600 mm & dia.100mm having polycarbonate clear/milky diffuser mounted on 3mm thick aluminium finished powder coated pipe with base plate 160x160mm with erection by M8x75mm fastner with required RCC foundation.IP65 for 9 to 20 watt ,surge-4kv- cat-III

Providing and erecting out door type halogen fitting made from cast alloys with electro- chemically polished Aluminium reflector complete with tuffend glass, silicon gasket with Halogen tube of following size (A) With 500 watt Halogen Tube

Providing and fixing Terminal board of size 5.0 x 127 x 152.4 mm.bakelite sheet with suitable brass studs with nuts, washers and clamps of size 25mm x 3mm suitable for pole painted with one coat of red lead paint.

Supplying & erecting approved make Digital time switch having lithium cell 6 years operative and operate battery backup 1 channel day clock with 14 memory programme, suitable to operate on 240V + 5%, 16A with, floating contacts Minimum switching setup time 1 minimum & LCD display. Also comprised permanent ON/OFF switching. Programming switches & housed in fire proof thermoplastic enclosure & transparent cover erected as required with necessary connection erected as directed.

Supplying & erecting power contactor ,AC3 duty for time switch complete erected as per direction Cat III (B) 2 pole 250V 32 Amp.

Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv grade ISI marked copper wires of following size to be erected as directed. e) 1.50 Sq.mm 3 core round PVC sheathed

Supplying and erecting B class Galvanized iron pipe having smooth finished bore of the pipe on both ends erected nuts and bolts along the pole / wall shaping the pipe as per site requirement. Pipe dia as following. (C) 40 mm dia.

Providing and erecting Pipe type earthing with 40 mm dia 2.5 mtr long 'B' grade G.I. pipe with necessary coupling buch buried in specially prepared earth pit & G.I. earth wire of 8 SWG erected & connected as directed (For panel) For using salt and charcoal / coke as required for pipe type earthing.

Providing & laying approved make Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same material at required depth in existing trench for laying of cable. below ground / road surface for enclosing cable (A)50 mm outer dia

providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark

Making trench in Hard Murrum / Tar Road of suitable width of 90 cm or required depth for laying any size of cable or locating the fault all over the run and back filling the same and making the surface as normal ground.

Making trench in soft soil of suitable width of 90 cm deep for laying cable or locating the fault all over the run and back filling the same and making the surface as normal ground.

Providing and fixing approved make 'T' Junction for Perforated C type cable tray. Made from sheet steel. The Junction should be bended as per IS 2062/1079 and shall be coated with hot dip galvanizing as per IS 2629/4759. with max 17.5% perforation with coupler plate / Fish plate and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification and as per instruction of engineer in charge of following size (2) 100 X 50 X 1.6 mm Thick

Providing and fixing approved make 'T' Junction for Perforated C type cable tray. Made from sheet steel. The Junction should be bended as per IS 2062/1079 and shall be coated with hot dip galvanizing as per IS 2629/4759. with max 17.5% perforation with coupler plate / Fish plate and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification and as per instruction of engineer in charge of following size (5) 300 X 50 X 2.0 mm Thick

Providing and fixing approved make 'T' Junction for Perforated C type cable tray. Made from sheet steel. The Junction should be bended as per IS 2062/1079 and shall be coated with hot dip galvanizing as per IS 2629/4759. with max 17.5% perforation with coupler plate / Fish plate and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification and as per instruction of engineer in charge of following size (6) 450 X 50 X 2.0 mm Thick

Supplying & erecting carbon dioxide (CO2) fire extinguisher user of following capacity with necessary clamps made from 50 x 6 mm M.S. Flat with nut & bolts grouted in wall complete. [A] For 4.5 Kg Capacity

Supplying & erecting ABC powder type 'Ceasefire' type Fire extinguisher as per IS 13849 or 1 Kg capacity with necessary clamp for erection on wall

SITC of sensor isolator mounting base, includes stainless steel contacts, slim profile - only 8mm, quick connection via square cable clamps, facility for remote indicator, Approved by LPCB (Including Five year free maintenance with guarantee)

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

SITC of Active Repeater Panel to be integrated with Fire Alarm Control Panel,larger display Full colour 800 x 480 LCD with resistive touch screen and automatic back-light dimming and the status of any Fire/Fault of Integrated Fire Alarm Panels, Panel should compliant with EN54-2, EN54-4 and Approved by LPCB (Including Five year free maintenance with guarantee)

SITC of Microprocessor based Net-workable Analogue Addressable Fire Alarm Control Panel. The Panel shall be compliant with EN54-2, EN54-4 and approved by LPCB. The Fire Alarm Control Panel shall have inbuilt 3 loops and expandable upto 4 Loops. The Panel must have large graphic display. The Panel must also have the capability to take Addressable Intelligent Wired and Wireless Devices on same loop. Each loop shall have a capacity of 127 analogue Addressable devices and 127 Base sounders/Base Sounder Beacons. The Panel shall have 240 V AC power supply along with automatic Battery Charger. Approved by LPCB (Including Five year free maintenance with guarantee)

Supply, Installation, Testing and Comissioning of 4MP Varifocal Lens Dome Type Camera, H.265 4MP IR Turret Dome N/W Camera, Manual Varifocal 2.8-12mm, 50M, Micro SD, DC12V/PoE, IP67/IK10, Basic IVA, 4MP resolution (2560 × 1440), True day/night, Digital WDR, 3D DNR, HLC & BLC, Triple streams, Smart codec by ROI, Built in MIC, Cyber Security, Basic intelligent video analytics, Audio In, NDAA Compliance, UL, CE, FCC Certified (Including Five year free maintenance with guarantee)

Supply, Installation, Testing and Comissioning of 4MP Varifocal Lens Bullet Camera, H.265 4MP IR Bullet N/W Camera, Manual Varifocal 2.8-12mm, 50M, Micro SD, DC12V/PoE, IP67/IK10, Basic IVA, 4MP resolution (2560 × 1440), True day/night, Digital WDR, 3D DNR, HLC & BLC, Triple streams, Smart codec by ROI, Cyber Security, Basic intelligent video analytics, NDAA Compliance, UL, CE, FCC Certified (Including Five year free maintenance with guarantee)

Supply, Installation, Testing and Comissioning of 64 Channel Network Video Recorder (NVR), Dual OS design, HDD Hot Swap with RAID support, N+1 hot spare configuration, Support 16CH@2MP, H.265/H.264 Video Compression, HDMI, VGA output, up to 8 SATA interface each with max 10 TB support and 1 eSATA, 16-ch synchronous playback at up to 1080p resolution, Gigabit Ethernet network interfaces, bandwidth 320 mbps, CE FCC, BIS, Operating Temp -10 deg to 50 deg C, USB and serial Interface, RAID supported (Including Five year free maintenance with guarantee)

SITC of SCREEN SIZE 105.41 cm diagonal (42” INCH), RESOLUTION FHD (1920*1080), USB INPUT (2.0 SUPPORT) 2*Side(USB2.0), HDMI INPUT 2*Side(HDMI 1.4), USB DEVICE SUPPORT USB Supported HDD, HOTEL MODE Yes, Basic, BLUETOOTH Yes (Ver. 4.1), WIFI TYPE(STANDARD) 802.11a/b/g/n 2.4G 2T2R, Built-in, WIFI BAND TYPE 2.4GHz, OS & VERSION INFO Android 'P' - 9.0, MEMORY FLASH 8GB EMMC, RAM 1.5.0GB , DDR3 2133Mhz. (Including Five year free maintenance with guarantee)

SITC of 48 x 10/100/1000BASE-T ports 4 x Gigabit GbE/SFP combo ports Advanced L2 switching and security features L2+ Static Routing Optional “standard mode” or “surveillance mode” management user interface [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]

Supply, Installation, Testing and commissioning of 6 TB Surveillance Series Hard disk supporting 24X7 operational efficiency

Providing & Erecting Netwrok rack with following capacity with Necessary cooling fan,Cable manager,6A PDU,equipment rack with necessary mounting accessories. (D) 15 U

Providing, erecting, testing & commissioning approved make oil immersed ONAN cooled, double wound, core type indoor / outdoor copper wound 11KV/ 433V step down transformer of following capacities operating on 3 phase, 50 Hz 4 wire & neutral earthed system continuously rated for a full temperature rise in oil not exceeding 45 Deg.C.at maximum ambient temp. of 50 Deg. C. complete with necessary radiator first filling of new transformer oil & standard fitting as below complying with IS 1180( Part 1 ):2014 standards with energy efficiency level 2 Off load tap changing range steps +2.5% to -5% on H.V for variation should be provided. The H.V. shall be connected Delta & Secondary with star connection. The transformer should have cable-end boxes on H.T. side suitable for up to 3 core 150 sq.mm. XLPE cable & on L.T. side suitable for bus duct or cables as per requirement complete with test certificates from manufacturers 1. Oil conservator with filling Hole & Cap - One No. 2. Thermometer pocket with 6" dial type thermometer switch alarm & trip contacts- Two nos. 3. Silica-gel breather with charge- One No. 4. Plain oil level gauge - One No. 5. Drain / Sampling / Filter valve- One No. 6. Top Filter Valve - One No. 7. Explosion vent with Diaphragm - One No. 8. Rating & Diagram plate - One No. 9. Additional neutral bushing for earthing - One No. 10. Bi directional Roller - Four Nos. 11. Earthing terminals - Two Nos. 12. Lifting lugs - Two Nos. 13. Air release plug. - One No. 14. Double float buchholz relay with Alarm and trip contacts. 15. Control cable as required from Transformer to VCB Panel is to be provided with necessary connection to VCB relays for protection. as per IS 1180 level-2 (b)315 KVA Max. allowable loses at 50 % of rated load is 1.025 KW and at full load is 3.1 KW

Providing, and erecting 11 KV D.P. 9 mtr. high Structure made of 6" x 3" ‘I’-Section Girder, 4" x 2"channels, clamps, nuts, bolts etc. Suitable for erection of the followings duly connected with necessary ACSR conductors. as per drawing approved by the Engineer- in charge complete with following. Height as per IS 7 Mtr above ground ) (A) 11 KV 200 Amps Drop out fuses with S.R.B.P. tubes carries.-Three nos (B) 11 KV G.O.D. switch complete with insulators, operating handle with galvanised pipe, Sq.bar etc. 400 Amp.- One Set (C) 11 KV lightening arrestor with clamp- Three Nos. (D) 11 KV shackle insulators- Six Nos. (E) The above D.P. structure should be earthed with 25 mm.X 3 mm thick double copper earth strips run separately and connected with separate copper plate earth electrode

Providing and erecting ISI Marked 3core 240 Sq.mm XLPE insulated 11 KV armoured cable Aluminium conductor IS-7098 to be laid on wall with clamps or in provided cable trench / pipe approved manner as directed.

Providing and erecting cable end termination kit, heat shrinkable Push on type Densons/ Raychem/ Elastimold make suitable for 11 KV XLPE cable 3core 95 & 120 Sq.mm (A) Outdoor type

Providing and erecting cable end termination kit, heat shrinkable Push on type Densons/ Raychem/ Elastimold make suitable for 11 KV XLPE cable 3core 95 & 120 Sq.mm (B) Indoor type

Providing, erecting, testing commissioning & getting Plan Approval as well as NOC from Electrical Inspector for extensible H.T panel comprising of one 400A. H.T. VCB incoming & Two outgoing 400 A Drawout type VCB confirming as per I.S. for use on 11 KV, 3 phase, 50 c/s. unearthed A.C. supply system having breaking rupturing capacity of 350 MVA complete with spring operated mechanism, mechanically & automatic ON-OFF and spring mechanism charged, discharged indicators, ON-OFF mechanical push button, operation counter necessary auxiliary switches, closing shunt trip, air insulated busbar chamber having heat shrinkable PVC sleeves, mechanical interlocks safety shutters, isolating plugs and a VCB trolley with three vacuum interrupters with epoxy support insulators and self aligning finger type isolating contacts. The breaker shall be Manual cum motorised mechanism & auto spring charge with TNC switch closing with following accessories. 1. 144 mm. square flush mounting type digital multifunctional meter with communication facility - Three sets. 2. Power Factor Meter One No 3. Double core current transformer cast resin type having ratio 200 to 50/1 core for metering & second core for protection having required class of accuracy. - Three Sets 4. Instantaneous under voltage relay& Temperature rise Tripping Relay 5. Electrical closing coil & short trip coil operating on 110V. D.C.- Three Sets 6. Auxiliary relay for anti pumping device 7. Three phase Three limb Drawout type feeder connected & output of 200 VA cast resin insulated potential transformer having ratio 12000V./110V. and 200 VA Burdon with 0.5 accuracy. - One No. 8. Common Alarm bell operating on 110V A.C.- One No. 9. Digital KWH Meter - One No. 10. Cable boxes suitable up to 11 KV 3core 150 sq.mm XLPE cable. - Three Nos 11. 230V. A.C. to 110V. D.C. power pack for closing & tripping circuit common. 12.Breaker ON-OFF, Auto trip and spring charged indicators. - Three Sets. 13.Phase indicating & panel illumination lamps with plug socket - Three Sets. 14.Numerical Communicable type non directional O/C & E/F Relay with a setting of 5-250% both in O/C & E/F. -Three Set complete with necessary interconnection with air insulated high grade copper busbar {Breaker Testing scope include Closing Time, Opening Time, VCB Hi-Pot test at Site}{ Relay Testing Scope Include testing of all protection by three phase testing kit at site }(VCB Trolley is to be provided)

Providing and erecting Inverter based approved make split air-conditioning unit consisting of condensing unit with variable speed fan motor, inverter type hermetically sealed rotary compressor with accessories etc. duly connected separately erected evaporating unit and blower motor with its accessories by means of extra supplied proper insulated copper tubing,drain PVC pipes suitable for ( cost includes Eco Friendly green gas charging and 15A plug top & Remote Control & MS Stand) with necessary core cutting. (2)For 4/5 Star Rating of current year (C) for 2.0 ton capacity-Premium Cat.

Supply, Installation, Testing & Commissioning of following size of Grid Tied Solar Power Plant with Solar Panels (ALMM approved): Frame Material : Anodized Aluminum alloy Frame With Twin Wall Profile, Front Cover : High Transmission Low-Iron Tempered Glass (AR Coated), High efficency and positive power tolerance Pmax: 0/+5, Module Efficiency should be approx. 18%-21%, Normal operating temperature 45'C, Junction Box with Waterproof IP67 & MC4 Compatible and Enclosed with Bypass diodes, 100% Electroluminescence test to ensure error free Modules, Thep. temp. co-efficient of the PV module shall equal or better than -0.45%/degree C. Solar PV modules of minimum fill factor 75% to be used. Unit Production:- 4 to 5 Unit /kw /day (Actual)(1Year Avg) With 10 year Product warranty and 25 year Linear Power Warranty., Solar Inverter: MPPT Range: 80-1000 V, Max efficiency: 97.5% - 98.9%, O/p Frequency: 50/60Hz, Operating Altitude (m) ≤4000, O/p Power Factor: ~1, O/P THDi: <3%, Operating Tempreture Range: -25~60°C, Anti-islanding Protection:Integrated, Input Reverse Polarity Protection Integrated, Insulation Resistor Detection Integrated, Residual Current Monitoring Unit Integrated, Output Over Current Protection Integrated, Output Short Circuit Protection Integrated, Output Over Voltage Protection Integrated, Protection Degree: IP65, User Interface LCD & APP,Datalogger & Communication: GPRS / Wi-Fi, Module Mounting Structure: Seamless Box Pipe / 'C' Channel of suitable size for rooftop solar installations with good stability agaist wind & weight load., Hot Dipped Galvanized steel coils. suitable arrangement for base plate for foundation , solar panel mounting, the structure should be suitable for carry the load of solar panel,wiring, sprinkler system etc. with necessary foundation work/wall mount, j bolt, anchor fastner etc. the nut bolt used for installtion of stucture should be (SS 304) quality. and Balane of System with necessary Swithgears (Suitabel size and protection of ACDB & DCDB), inter connecting wiring, earthing system, lightining arrester system, all liasoning work with various gov. dipartment like state nodal agency,DISCOM & CEIG is included in agency scope(Excluding GEDA Application fees, Solar connectivity Charges, Meter connectivity Charges, Meter testing Charges.) (F) Grid Tied Solar Power System: 101 - 250 kW (3 - phase)

Providing & erecting Automatic solar panel cleaning system for solar power projects which includes necessary plumbing work (UPVC pipes and accessories) from source of water to project site (upto 30 meters),Suitable size of sub mercible/ open well motor, necessary wiring for motor and sprinkler system with safety, timer circuit for automatically on/off the sprinkler system, necessary size oand number of nozzles/JET (minimum 1 Nozzle/Jet per module).(F) 101KW-200KW Cleaning System

Main Fire Hydrant Pump- Electric Motor Driven: SITC of: Back pull out type -Single Stage, Self Mriming, Centrifugal Pump for Main Fire Pump with Electric Motor, Base frame and Couplings. MOC:-Casing-CI, Impeller- Bronze, Shaft- SS 410, Sleeve-SS410. Flow Capacity: 2280 LPM Head: 65 mtr Speed: 2900 Approx Pump shall be capable of furnishing not less than 150% of rated capacity at a head not less than 65% of rated head The shut off head shall not exceed 120% of rated head. UOM:-Price Per Complete set of Pump + Motor + Accessories. Note:-01. Minor civil work like tank hole/ Core Cutting etc. are in bidders scope. Location: In Pump Room Make: Kirloskar / Lubi

Main Fire Sprinkler Pump- Electric Motor Driven: SITC of: Back pull out type -Single Stage, Self Mriming, Centrifugal Pump for Main Fire Pump with Electric Motor, Base frame and Couplings. MOC:-Casing-CI, Impeller- Bronze, Shaft- SS 410, Sleeve-SS410. Flow Capacity: 2280 LPM Head: 60 mtr Speed: 2900 Approx Pump shall be capable of furnishing not less than 150% of rated capacity at a head not less than 65% of rated head The shut off head shall not exceed 120% of rated head. UOM:-Price Per Complete set of Pump + Motor + Accessories. Note:-01. Minor civil work like tank hole/ Core Cutting etc. are in bidders scope. Location: In Pump Room Make: Kirloskar / Lubi

Jockey Fire Pump- Electric Motor Driven: SITC of: Back Pull-out End Suction Type -Single Stage, Self Priming, Centrifugal Pump for Jockey Fire Pump with Electric Motor, Mechanical Seal, Base-frame and Couplings. MOC:-Casing-CI, Impeller- Bronze, Shaft- SS 410, Sleeve-SS410. Flow Capacity: 180 LPM Head: 65 mtr Speed: 2900 Approx Pump shall be capable of furnishing not less than 150% of rated capacity at a head not less than 65% of rated head The shut off head shall not exceed 120% of rated head. UOM:-Price Per Complete set of Pump + Motor + Accessories. Note:-01. Minor civil work like tank hole/ Core Cutting etc. are in bidders scope. Location: In Pump Room Make: Kirloskar / Lubi

Standby Fire Pump- Diesel Engine Driven SITC of: Diesel Engine driven Standby Pumping System complete with,diesel engine, Back Pull-out Type Single Stage, Self Priming, Centrifugal Pump, Couplings & Base-frame: MOC:- Pump Casing-CI, Impeller- Bronze, Shaft-SS410, Sleeve- SS410. Flow Capacity: 2280 LPM Head: 65 mtr Speed: 2900 LPM Diesel Engine includes 100 ltr diesel tank, battery, battery charger, engine oil and coolant. UOM:-Price Per Each Set. Note:-01. Minor civil work like tank hole/ Core Cutting etc. are in bidders scope. Location: In Pump Room Make: Kirloskar / Lubi

Fire Pump Control Panel- Auto and Manual Type. Supply, Installation and Testing of: Electric Control Panel for Electric Motor Driven Main Fire Pump, Sprinkler Pump and Jockey Fire Pump. all pumps can be Start Automatically (by Pressure Switch) & Manually. Design As per the Detail Specifications given. UOM:-Price Per Set. Location: In Pump Room Make: Kirloskar / Lubi

Air Vessel: SITC of Pressurized Air Vessel f Size 450 mm Dia x 2000 mm long fabricated from 10 mm thick MS Plate with 25 mm drain valve, air release valve with ball valve on top and isolation valve.

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall FRLS type with necessary clamps or in existing trench / pipe of following size of cables - 3.5 core 70 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. - 3.5 core 70 Sq. mm

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. - 70 Sq.mm.

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall FRLS type with necessary clamps or in existing trench / pipe of following size of cables - 4 core 16 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. - 4 core 16 Sq. mm

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. - 16 Sq.mm.

Pressure Gauge with Siphon Tube and Cock. Supply, Installation and Testing of: Pressure Gauge with Siphon Tube and Cock. MOC:-4” Dial- Glycerin filled- Stainless Steel Body Pressure Gauge with GI Siphon Tube andBrass Cock. Size:-Dial: 4” (100 mm) Range: 0 – 16 Bar (kg/cm2) UOM:-Price Per Unit

Pressure Switch with Siphon Tube and Cock. Supply, Installation and Testing of: Pressure Switch with Siphon Tube and Cock. Size:- Range suitable for System Design Pressure. UOM:-Price Per Unit

Pipe Laying. Supply, Fabrication, Installation, Hydro Testing & Painting of Under Ground Pipe. With necessary Pipe Fitments (Flanges, Bands, Socket etc.), MS Support/Clamps/Hangers, Coating etc. Hardware (Gaskets, Nut-Bolts, Paint etc.), Consumables (Welding Rod, etc.) and Labour Charge. Quality: GI, C-Class (Heavy). Paint: UOM:-Price Per Running Meter Size: 200 mm

Pipe Laying. Supply, Fabrication, Installation, Hydro Testing & Painting of Under Ground Pipe. With necessary Pipe Fitments (Flanges, Bands, Socket etc.), MS Support/Clamps/Hangers, Coating etc. Hardware (Gaskets, Nut-Bolts, Paint etc.), Consumables (Welding Rod, etc.) and Labour Charge. Quality: GI, C-Class (Heavy). Paint: UOM:-Price Per Running MeterSize: 150 mm

Pipe Laying. Supply, Fabrication, Installation, Hydro Testing & Painting of Under Ground Pipe. With necessary Pipe Fitments (Flanges, Bands, Socket etc.), MS Support/Clamps/Hangers, Coating etc. Hardware (Gaskets, Nut-Bolts, Paint etc.), Consumables (Welding Rod, etc.) and Labour Charge. Quality: GI, C-Class (Heavy). Paint: UOM:-Price Per Running Meter Size: 100 mm

Pipe Laying. Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe. With necessary Pipe Fitments (Flanges, Bands, Socket etc.), MS Support/Clamps/Hangers etc. Hardware (Gaskets, Nut-Bolts, Paint etc.), Consumables (Welding Rod, etc.) and Labour Charge. Quality: GI, C-Class (Heavy). Paint: UOM:-Price Per Running Meter Size: 200 mm

Pipe Laying. Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe. With necessary Pipe Fitments (Flanges, Bands, Socket etc.), MS Support/Clamps/Hangers etc. Hardware (Gaskets, Nut-Bolts, Paint etc.), Consumables (Welding Rod, etc.) and Labour Charge. Quality: GI, C-Class (Heavy). Paint: UOM:-Price Per Running Meter Size: 150 mm

Pipe Laying. Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe. With necessary Pipe Fitments (Flanges, Bands, Socket etc.), MS Support/Clamps/Hangers etc. Hardware (Gaskets, Nut-Bolts, Paint etc.), Consumables (Welding Rod, etc.) and Labour Charge. Quality: GI, C-Class (Heavy). Paint: UOM:-Price Per Running Meter Size: 100 mm

Pipe Laying. Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe. With necessary Pipe Fitments (Flanges, Bands, Socket etc.), MS Support/Clamps/Hangers etc. Hardware (Gaskets, Nut-Bolts, Paint etc.), Consumables (Welding Rod, etc.) and Labour Charge. Quality: GI, C-Class (Heavy). Paint: UOM:-Price Per Running Meter Size: 80 mm

Pipe Laying. Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe. With necessary Pipe Fitments (Flanges, Bands, Socket etc.), MS Support/Clamps/Hangers etc. Hardware (Gaskets, Nut-Bolts, Paint etc.), Consumables (Welding Rod, etc.) and Labour Charge. Quality: GI, C-Class (Heavy). Paint: UOM:-Price Per Running Meter Size: 65 mm

Pipe Laying. Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe. With necessary Pipe Fitments (Flanges, Bands, Socket etc.), MS Support/Clamps/Hangers etc. Hardware (Gaskets, Nut-Bolts, Paint etc.), Consumables (Welding Rod, etc.) and Labour Charge. Quality: GI, C-Class (Heavy). Paint: UOM:-Price Per Running Meter Size: 50 mm

Pipe Laying. Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe. With necessary Pipe Fitments (Flanges, Bands, Socket etc.), MS Support/Clamps/Hangers etc. Hardware (Gaskets, Nut-Bolts, Paint etc.), Consumables (Welding Rod, etc.) and Labour Charge. Quality: GI, C-Class (Heavy). Paint: UOM:-Price Per Running Meter Size: 40 mm

Pipe Laying. Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe. With necessary Pipe Fitments (Flanges, Bands, Socket etc.), MS Support/Clamps/Hangers etc. Hardware (Gaskets, Nut-Bolts, Paint etc.), Consumables (Welding Rod, etc.) and Labour Charge. Quality: GI, C-Class (Heavy). Paint: UOM:-Price Per Running Meter Size: 25 mm

Gate /SluiceValve Supply, Installation and Testing of: Gate/ Sluice (Rising Spindle -Screw & Yoke Type) Valve with necessary pipe fitments, hardware and consumables. MOC:-Body: Cast Iron, Disk: Cast Iron, Seat: Nitrile, Stem: SS. (With Flange Ends). Standard: ISI Marked. UOM:-Price Per Each No. Size: 200 mm

Gate /SluiceValve Supply, Installation and Testing of: Gate/ Sluice (Rising Spindle -Screw & Yoke Type) Valve with necessary pipe fitments, hardware and consumables. MOC:-Body: Cast Iron, Disk: Cast Iron, Seat: Nitrile, Stem: SS. (With Flange Ends). Standard: ISI Marked. UOM:-Price Per Each No. Size: 150 mm

Gate /SluiceValve Supply, Installation and Testing of: Gate/ Sluice (Rising Spindle -Screw & Yoke Type) Valve with necessary pipe fitments, hardware and consumables. MOC:-Body: Cast Iron, Disk: Cast Iron, Seat: Nitrile, Stem: SS. (With Flange Ends). Standard: ISI Marked. UOM:-Price Per Each No. Size: 80 mm

Check Valve Supply, Installation and Testing of: Check Valve (Ball type or Swing type) with necessary pipe fitments, hardware and consumables. MOC:-Body: Cast Iron (With Flange Ends). Standard: ISI Marked. UOM:-Price Per Each No. Size: 150 mm

Check Valve Supply, Installation and Testing of: Check Valve (Ball type or Swing type) with necessary pipe fitments, hardware and consumables. MOC:-Body: Cast Iron (With Flange Ends). Standard: ISI Marked. UOM:-Price Per Each No. Size: 80 mm

Check Valve Supply, Installation and Testing of: Check Valve (Ball type or Swing type) with necessary pipe fitments, hardware and consumables. MOC:-Body: Cast Iron (With Flange Ends). Standard: ISI Marked. UOM:-Price Per Each No. Size: 50 mm

Butterfly Valve Supply, Installation and Testing of: Butterfly Valve with necessary pipe fitments, hardware and consumables. MOC:-Body: Cast Iron, Disk: SS, Seat: Nitrile. UOM:-Price Per Each No. Size: 150 mm

Butterfly Valve Supply, Installation and Testing of: Butterfly Valve with necessary pipe fitments, hardware and consumables. MOC:-Body: Cast Iron, Disk: SS, Seat: Nitrile. UOM:-Price Per Each No. Size: 100 mm

Butterfly Valve Supply, Installation and Testing of: Butterfly Valve with necessary pipe fitments, hardware and consumables. MOC:-Body: Cast Iron, Disk: SS, Seat: Nitrile. UOM:-Price Per Each No. Size: 80 mm

Butterfly Valve Supply, Installation and Testing of: Butterfly Valve with necessary pipe fitments, hardware and consumables. MOC:-Body: Cast Iron, Disk: SS, Seat: Nitrile. UOM:-Price Per Each No. Size: 50 mm

Strainer. Supply, Installation and Testing of: Y Type Strainer with necessary pipe fitments, hardware and consumables. MOC:-Body: Cast Iron, Mesh: SS-304. Working Pressure: 10 Bar UOM:-Price Per Each No. Size: 200 mm

Air Release Valve- 25 mm Supply, Installation and Testing of: Air Release Valve Check Valve with necessary pipe fitments, hardware and consumables. MOC:-Body: Gunmetal / SS. UOM:-Price Per Each No.

Fire Hydrant Landing Valve (Stainless Steel (SS-304), ISI Marked): Supply, Installation and Testing of: Fire Hydrant Landing Valve with necessary pipe fitments, hardware and consumables. MOC:-Body: Stainless Steel (SS-304), Working Parts: Stainless Steel (SS-304), Coupling: Stainless Steel (SS-304), Standard: -ISI Marked. Size:-63 mm (Flange End: NB 75 mm, PCD 160 mm) UOM:-Price Per Each No.

Fire Hose Pipe (Delivery Hose)- 63 mm x 15 m Supply, Installation and Testing of: Fire Hose with Hose Couplings. RRL (ISI Mark- Type A) Fire Hose. Hose Couplings: ISI Marked Stainless Steel. With SS Wire Binding. Standard: - ISI Marked & TAC Approved Hose. Size:-63 mm dia x 15m long Hose. UOM:-Price Per Each Set.

Cabinet For Fire Hose (Hose Box)- Double Type Supply, Installation and Testing of: Fire Hose Cabinet (Hose Box) suitable to accommodate 02 no. of 15 m long fire hoses and 01 no. of nozzle. With Lock-n-key facility. Wall Mounting Design. MOC: 16 Gauge MS Box with Powder Coating Standard: - As per Guidelines. Size:- Suitable for 02 nos. of 15 m long hoses. UOM:-Price Per Each No.

Fire Hose Nozzle- Short Branch Pipe Nozzle. Supply, Installation and Testing of: Short Branch-pipe Nozzle. MOC: Stainless Steel (SS-304). Standard: ISI Marked, Heavy Quality. Size:- 63 mm X 20 mm UOM:-Price Per Each No.

Fire Hose Reel Set (ISI)-19 mm x 30 m -Rubber Hose. Supply, Installation and Testing of: Fire Hose Reel Set with necessary pipe fitments, hardware and consumables. MOC:-Drum: 16 G Powder Coated MS, Hose: 19 mm X 30 m heavy-duty RUBER hose. Shut-off Nozzle: SS-304. With Control Valve: SS- 25mm Ball Valve. Standard: ISI Marked. Heavy Quality. Size:-19 mm dia x 30m long Hose. UOM:-Price Per Each No.

Fire Service In-let (In-let Connection for Fire Brigade)-4 Way Type. Supply, Installation and Testing of: Fire Service Inlet with necessary hardware and consumables. MOC:-Body: Heavy-duty CI. Couplings/NRV: Gunmetal. Standard: -Made As per IS Standard- Heavy duty quality. Size:-Couplings: 63 mm, 150 mm E-table Flange End. UOM:-Price Per Each No.

Sprinkler Head/ Nozzle. Supply, Installation and Testing of: K 5.6 Pendent type Standard Response Sprinkler rating of 57 deg.C. with required accessories. MOC:-Brass Standard: UL Listed Size:-15 mm (1/2”) UOM:-Price Per Each No.

Sprinkler Drop Pipe: Supply, Installation and Testing of: Sprinkler Drop Pipe with necessary pipe fitments. Standard: UL Listed UOM:-Price Per Each No. Make: Safex/Tyco/ UL Listed

Flow Switch Supply, Installation and Testing of: Flow Switch with necessary pipe fitments, hardware and consumables. UOM:-Price Per Each No. With all wiring/ cabling up to control panel and all electrification.

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall FRLS type with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cable. (a) 3 core 2.5Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. (a) 2 to 4 core 2.5 Sq. mm

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (A) 1.5/ 2.5/4/6 Sq.mm

Providing, fixing, testing and commissioning of Annunciator panel for flow control switch, providing Audio/Visual indicating of actuation of automatic sprinkler system for each zone complete as per specifications with provision for 30 zones (22 working and 8 spare for future). 'Indication of zone fire, 'Indication of zone fault, 'Fire/Fault hooter, 'Alarm cancel for fire/fault, 'Battery for emergency Make: CPRI Approved

Providing and fixing, testing and commissioning of Drainning Valve 50mm dia with by pass drain connection as required.

Providing and fixing, testing and commissioning of CO2 type Fire Extinguisher of capacity 22.5 kg filled with Co2 Gas as per IS 15222 with controll discharge mechanism fitted with Hose, Horn & TROLLEY confirms to IS 2878 bearing ISI mark. Co2 Cylinder as per IS 7285.

Fire Extinguisher- ABC Powder type, 6 kg. Supply, Installation and Testing of: ABC Powder Fire Extinguisher necessary hardware and consumables. Stored Pressure Mechanism. Charged with MAP-50 % (ABC) Dry Powder. With wall mounting clamp. Size:-6 kg Powder. UOM:-Price Per Each No.

Fire Extinguisher- CO2 Gas type, 4.5 kg. Supply, Installation and Testing of: CO2 Gas Fire Extinguisher with necessary hardware and consumables. Standard: - Confirming to IS: 15683-2006 with ISI Mark. Size:-4.5 kg UOM:-Price Per Each No.

Supplying FIRE bucket round bottom of 9 litres capacity made out of 24 gauge G.I. sheet with extra handle at bottom duly painted white inside and Red out side with FIRE mark, filled with dry-sand and kept on existing stand provided or hung on wall hook.

Supplying and erecting floor mounting stand for keeping four nos. of FIRE buckets comprising 1500 mm in length, 900 mm height frame made out of 30mm X30 mm X 4 mm angle iron with cross supports for legs, welded with 4 hooks and duly painted with one coat of red lead and two coats of approved enamelled silver paint.

Safety Signage- Night Glow Type: SIRC of: Single Side Printed Night Glow (Glow in Dark ) Safety Signage. Printed on PVC sticker sheet and pasted on 3-5 mm thick PVC foam sheet. Size: 10” X 10”.

RCC Hume Pipe: Providing and Laying NP3 RCC Hume Pipe of 300 mm at road crossing including excavation for pipe line trenches incl. all safety provisions using site rails and stacking excavated stuff up to a lead of 90 mts. cleaning the site etc. complete for lifts and strata as specified upto 1.5 mt. Depth. Also refilling the pipeline trenches incl. ramming, watering consolidating desposal of surplus stuff as directed within a radius of 3 K.M.

Approval of Fire Hydrant & Entire Fire Protection System from Local Fire Authority and any other relevant statutory authority at initial and various other stages of work, including preparation of report/drawings as per fire authority requirement. Contractor shall include cost of all liason work which are not explicitly mentioned above but are mandatory to have fire authority approval (any statutory charges will be paid extra).

M/s. Natvar Construction Co. (BID ID -20708)

M/s D. H. Patel and Co (BID ID -20714)