PROVISION OF EXHAUST FAN VARIOUS STORES AT CSD DEPOT AND CONSTRUCTION OF GODOWN BEHIND GP II CSD DEPOT UNDER GE GUWAHATI

Amount

S&F Flame proof, Exhaust Fan 457 mm or 18" sweep, 1400 RPM, AC single phase 230 V double ball bearing with bird guard, metallic body and blade, complete with nuts, screws, bolts of specified size including electrical connection with twisted three core PVC insulated unshelthed flexible cord of size 0.75 sqmm copper conductor from ceiling rose to exhaust fan complete all as specified and directed

M&L concealed point wiring for light/fan controlled by one, one way switch complete with 1.5 Sqmm single core PVC insulated unsheathed FR-LSH cable 1100 volts grade (ISI marked) with multistranded copper conductor with proper colour coding drawn through and including stove enamelled steel conduit not less than 20mm dia with accessories concealed in in wall surfaces including provision of 1.5 Sqmm PVC insulated multistranded unsheated copper conductor cable FR-LSH (ISI markd) with proper colour coding as earth continuity conductor connected to common earth dolly , terminal box Connections of cable with MCBs or bus bar shall be done through proper size of copper/brass thimbles. Where concealing of conduit is not feasible ie on surface of roof etc, conduit shall be fixed on surface with necessary saddles at no extra cost complete all as specified and as directed Note:- Connections of cable with MCB's or bus bar shall be done through proper size copper/brass thimbles.

M&L Switch flame proof rotary type with termination box in LM6, 16A, single pole 250V complete all as directed

M&L concealed sub-main wiring alongwith earth wire of size of 2 x 6.0 sq. mm + 1 x 6.0 sq. mm earth wire, ISI marked, FRLSH, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including necessary cutting chases, pining in Conceled stove enamelled steel conduit with accessories of suitable size with all fittings and accessories and making good to walls, floors etc as per existing specifications complete all as specified and as directed. NOTE : (i) Two runs of PVC wire, one run of earth wire & one run of Steel Conduit will be measured as one length. (ii) Providing loop length as directed by Engg-in -charge is deemed to included in unit rate quoted

S&F Sheet metal enclosure for 8 way Distribution Boards (DB’s), IP-43 double door, Single pole & neutral with 200 amps rated bus bar, including blanking plates as required and flush to wall surface including making good the distrubed surfaces of walls as per existing surfaces and finishes, complete all as specified and as directed.

S&F MCB Single pole and Neutral, 32 amps, 240 volts, ‘C’ curve, 10 KA complete all as specified and as directed.

S&F MCB Single pole, 6 to 32 amps, 240 volts, ‘C’ curve, 10 KA complete all as specified and as directed.

Surface excavation in soft/loose soil, n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out complete all as specified and as directed.

Removing excavated material (Soil) not exceeding 50 metre and depositing where directed at a level not exceeding 1.50 metre above the starting point complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in soft/loose soil complete all as specified and directed.

M&L Hardcore of gauge n exc. 63 mm, using broken stone or boulders, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for 100mm thick PCC (1:3:6) type C2 as in sub base of flooring using 40mm graded stone aggregate finishing cement concrete surface even & fair complete all as specified and as directed.

M&L Brickwork with sub class ‘B’ bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L Rendering 10 mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:6 for finished even and fair complete all as specified and as directed.

M&L for 15mm thick rendering with cement mortar (1:4) on fair faces of brick work in two layers (10mm & 5mm) seperately mixed with water proofing compound in top layer as per manufacturer's instructions and finishing the surface even and fair without using extra cement complete all as specified and as directed. Note:- WPC shall be measured and paid seperately under appropiate item.

Supply only Liquid water proofing compound complete all as specified and as directed.

M&L prepration of new plastered surfaces of wall applying two coat of oil emulsion distemper over 3mm thick wall care putty to obtained smoothness of plastered surfaces including a coat of primer complete all as specified and as directed.

M&L preparation of new treated plastered surfaces of wall and applying two coat of weather proof paint (exterior quality acrylic emulsion paint) over a coat of suitable priming coat complete all as specified and directed

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 including necessary preperation of surfaces and applying one shop coat of red oxide, zinc chrome primer complete all as specified and as directed.

S&F 3.8 to 4mm dia galvanised steel wire, 150x100mm mesh, made up into mattresses or cages, lapped, wired and laid in position, including closing after filling complete all as specified and as directed.

S&F 100mm butt hinges, medium weight cold rolled, MS steel complete, all as specified and as directed.

S&F 150mm Extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and directed.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixedr complete all as specified and as directed.

S&F 150mm long aluminium anodized, barrel tower bolts of extruded section and fixed, complete all as specified.

S&F Prepainted galvalume aluminium zink coating GI based corrugated/semi corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and as directed.

M&L preparing new steel surfaces of any description, not otherwise describe over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

M&L 75mm thick cement concrete (1:3:6) type C-2( using 40mm graded crushed stone aggregate) as in plinth protection laid in alternate bays (not exceeding 2 Sqm each) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and n.exc 1.5m in depth forfor foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc and getting out hard / dense soil complete all as specified and as directed.

M&L PCC (1:4:8) type-D2 with using 40 mm graded crushed stone aggregate as in mass concrete for base etc complete all as specified and as directed.

M&L PCC (1:2:4) type B-2 (using 20 mm graded stone aggregate) as in surface channels and drain complete all as specified and as directed.

M&L PCC (1:2:4) type B-2 (using 20 mm graded stone aggregate) as in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) complete all as specified and as directed.

M&L Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter. flat, roughed finished surfaces, complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and as directed.

Add to or deduct for each 25 mm girth or part thereof over or under 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and as directed. Note:- Rate quoted is for adjustment of rate only for the actual size excuted at site for the item no 33.00 mentioned as above

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25cm complete all as specified and as directed.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe 290 Gde E-165 including necessary preperation of surfaces and applying one shop coat of red oxide, zinc chrome primer complete all as specified and as directed.

S&F Mild steel bolts.purpose made. with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. exc 30cm long and dia of neck 12mm complete all as specified and as directed.

S&F 1mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required including necessary preperation of surfaces and applying one shop coat of red oxide, zinc chrome primer complete all as specified and as directed.

M&L Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed.

M&L Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and as directed.

M&L Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and as directed.

M&L 25mm thick Damp proof course to horizontal or vertical surfaces in In cement concrete 1:2:4, type B-0 including necessary formwork complete all as specified and as directed.

M/s Dhani Enterprise