SPECIAL REPAIRS WORKS AT MILITARY STATION SRI GANGANAGAR

Amount

M & L for sand filling (25 mm thick) under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer - in - Charge.

M&L for PCC (1:5:10) type E-2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete or filling in sunken floor complete all as specified and directed by Engineer-in-Charge.

M&L providing cement concrete (1:3:6) Type C-1 (20 mm graded stone aggregate) for filling in pressed steel frames and other similar items etc complete all as specified and directed by Engineer - in - Charge

M&L providing precast cement concrete 1:2:4, Type B1 using 20mm graded aggregate as in kerb stone with solid blocks exc 10cm width and set in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L providing reinfoced cement concrete (nominal mix) in cement concrete 1:2:4 Type B1(20mm graded aggregate) as chajjas etc and similar work complete all as specified and directed by Engineer-in-Charge. (Note : The rate quoted shall be deemed to include use and waste of necessary form work)

M&L for pre-cast RCC jallies 40 mm thick(measured soild) 1:2:4 , Type B-1 (12.50 mm graded stone aggregate) and set in cement mortar 1:4 complete all as specified and directed by Engineer - in - Charge.

M & L brick work with sub class 'B' bricks(old size) straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 complete all as specified and directed by Engineer - in - Charge.

M & L brick work with sub class 'B' bricks straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 but except bricks complete all as specified and directed by Engineer - in - Charge.

S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engineer - in - Charge.

S & F Second class hard wood glazed and skeleton Door, kitchen cabinet shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc divided into squares with plain, chamfered or rounded mitred and rebated sash bars any number & fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, section 8 clause 8.24 (a) complete all as specified and directed by Engineer - in - Charge.

S&F 35mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed by Engineer - in - Charge.

Taking down chowkats or frames (without taking off shutters from the frame) n. exc.1.5 sqm each complete all as specified and directed by Engineer - in - Charge.

Taking down chowkats or frames (without taking off shutters from the frame) exc. 1.5 sqm and n. exc.4 sqm each complete all as specified and directed by Engineer - in - Charge.

Taking down steel window or ventilator of n.exc 1.5 sqm each complete all as specified and directed by Engineer - in - Charge.

Taking down shutters of any description exc. 1 Sqm but n.exc 2 sqm each and after easing/resecuring refixing in the same opening / place complete all as specified and directed by Engineer - in - Charge.

Taking down shutters of any description exc. 1 Sqm but n. exc 2 sqm each complete all as specified and directed by Engineer - in - Charge.

S&F Fiber Glass Reinforced plastic (FRP) Door Frames of required colour of three legged of cross section 90mmx45mm having single rebate of 32mmx45mm having single rebate of 32mmx15mm to receive shutter of 30 mm thickness. The laminate door frame molded with fire retardant grade unsaturate polysterresinn and chopped mat.Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiberglass from all sides, MS stay shall be provided at the bottom to steady the frame complete all as specified and directed by Engineer - in - Charge

S&F 30mm thick glass fiber reinforced plastic (FRP) paneled door shutter of required colour and approved brand and manufacture made with fire retardent grade unsaturated polyster resin moulded to 3mm thick FRP laminated for forming hollow rails and style with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings cast monolithically with 5mm thick FRP laminate for panels for conforming to IS:14856-2000 complete all as specified and directed by Engineer - in - Charge.

S&F Aluminium anodised barrel tower bolts 125 mm, stove enamelled black, with bright bolt and fixed complete all as specified and directed by Engineer - in - Charge.

S&F aluminium anodised barrel tower bolts 150mm long extruded section complete all as specified and directed by Engineer - in - Charge.

S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed by Engineer - in - Charge.

S&F butt hinges, heavy weight, cold rolled mild steel, and fixed of size 100mm fixing properly with screws etc complete all as specified and directed by Engineer - in - Charge.

S&F aluminium butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 of size 75mm fixing properly with screws etc complete all as specified and directed by Engineer - in - Charge..

S&F 300 mm size mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified & directed by Engineer-in-Charge.

S&F in repair 300 mm size mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified & directed by Engineer-in-Charge.

S&F Extruded aluminium alloy handles, fabricated type, anodised 150 mm long complete all as specified and directed by Engineer - in - Charge

S&F in repairs mortice lock with four lever (vertical type) with brass body 100 mm long complete all as specified and directed by Engineer-in-charge.

S&F drapery harrison rails/curtain rod 25 mm dia (minimum weight 0.36 Kg per RM) with brackets, fancy knobs and rings (20 cm c/c) etc complete all as specified and directed by Engr-in-charge.

S&F in repair stainless steel harrison rails/curtain rod 25 mm dia (minimum weight 0.36 Kg per RM) with brackets, fancy knobs and rings (20 cm c/c) etc complete all as specified and directed by Engr-in-charge.

S&F in repairs brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed by Engineer-in-Charge. Make:- Prayag cat part No- 323-Tor equivalent cat part as approved by GE

S&F floor door stopper of aluminium alloy body and tongue, overall length of cover plate 140mm anodised, with hard drawn steel spring, fixed in floor plate complete all as specified and directed by Engineer - in - Charge..

S&F in repairs door closer hydraulically regulated, designation No. 2, universal type, suitabel for door shutters of size 701 to 850 mm in width and of weight between 36 to 60 kg complete all as specified and directed by Engineer-in-charge.

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer - in - Charge.

S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed to window / ventilator with stainless steel wire staples complete all as specified and directed by Engineer - in - Charge

M&L for TMT bars 10 mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia using TMT bars complete all as specified and directed by Engineer - in - Charge.

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed by Engineer - in - Charge.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing Fe-290-W(Gde-E-165) complete all as specified and directed by Engineer - in - Charge.

M&L for pressed steel frame for doors of size 125 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed by Engineer - in - Charge.

M&L for Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. with Powder Coating on aluminium minimum thickness of powder coating 50 micron as per the specification top and bottom horizontal members and vertical members adjacent to walls and cills where required and fixing with the help of rawl plug and screw or with fixing clip or with expansion hold plate fasteners. Aluminium section shall be smooth, rust free, straight mitred and jointed mechanically where ever required complete all as specified and directed by Engineer - in - Charge.

S&F powder coated anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed by Engineer - in - Charge

S&F power coated aluminium snap grid frame work for false ceiling size 605x605 mm including hangers complete all as specified and directed by Engineer - in - Charge

S&F powder coated aluminium windows and ventilator luver shutters, side hung type without sash bars, aluminium saction weighing 0.55 kg/M including necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fitting such as aluminium peg stay 150mm long (1No), powder coated aluminium hinges type B-21 100 mm long (2No), suitable powder coated aluminium handle -(1No), and powder coated aluminium self closing tower bolt 75mm long (1No) complete all as specified and directed by Engineer - in - Charge.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated Mangalore tiles profile steel sheet 0.50mm thick of an colour (red) having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer - in - Charge

M&L for Pre-painted galvalume aluminum zinc coating GI based Plain Mangalore tiles profile steel sheet 0.50mm thick of red colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-charge.

S&F heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner complete all as specified and directed by Engineer-in-charge.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including fittings complete all as specified and directed by Engineer-in-charge.

S&F in repair 18/19 mm thick Prelaminated particle board, interior grade, prelaminated both sides with decorative choice laminations complete all as specified and directed by Engineer - in - Charge.

M&L for Providing and fixing Gypsum Board 12mm thick size (600x600) in false ceiling fixed with screw as per manufacturers instructions complete all as specified and directed by Engineer - in - Charge

M & L for 18-20 mm thick machine cut kota stone slab as in vertical surfces such as skirting, dados, laid over and including 10 mm thick backing coat in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed by Engineer - in - Charge.

M & L for 18- 20 mm thick (minimum size 55cmx 55 cm) machine cut kota stone slab flooring laid over and including 15 mm thick screed bed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed by Engineer - in - Charge.

M & L for 20-25 mm thick machine cut kota stone slab as in vertical surfces such as skirting, dados, laid over and including 10 mm thick backing coat in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed by Engineer - in - Charge.

M & L for 20-25 mm thick (minimum size 55cmx 55 cm) machine cut kota stone slab flooring laid over and including 15 mm thick screed bed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed by Engineer - in - Charge.

M & L for 75 mm thick cement concrete 1:3:6 type C –1 (20mm graded stone aggregate) as in plinth protection or similar works finished even and smooth with using extra cement etc complete all as specified and directed by Engineer - in - Charge.

M&L for 75mm thick cement concrete (1:4:8) type D-2, (40 mm graded stone aggregate) as in sub base, foundation filling and mass concrete complete all as specified and directed by Engineer - in - Charge

M&L for 25 mm thick cement concrete 1:2:4, Type B-0 (12.5mm graded aggregate) as in floor finished even and fair complete all as specified and directed by Engineer - in - Charge.

M&L for 40 mm thick cement concrete 1:2:4, Type B-1 (20mm graded aggregate) as in floor finished even and fair and smooth with using extra cement etc complete all as specified and directed by Engineer - in - Charge.

M&L for precast coloured rubber moulded concrete machine pressed concrete interlocking paver blocks any shape and size conforming to IS 15658-2006 of 60 mm thickness, M 35 grade set, jointed and pointed in neat cement slurry in floors/paving/path etc wirh grey cement and pigment complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises,complete all as specified and directed by Engineer-in-charge.

M&L for glazed ceramic coloured tiles interior grade, of size 450x350x7mm thick as on vertical surfaces like dados or skirting laid over and including 10mm thick rendering in CM 1:4 and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer - in - Charge.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but not exc 0.18 sqm in floor etc, laid over and including 15 mm thick screed bed in CM 1:4 and set and jointed in cement slurry and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer - in - Charge.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.18 sqm but not exc 0.36 sqm in floor etc, laid over and including 15 mm thick screed bed in CM 1:4 and set and jointed in cement slurry and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer - in - Charge.

M&L for virified ceramic tiles 10mm thick (square / rectangular) area of each tile n. exc 0.36 Sqm in floors etc. laid over and including 15 mm thick screed bed in CM 1:4, set and jointed in cement slurry mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer-in-Charge

Taking down cement plaster on brick or concreate wall surfaces including racking out joints, hacking for key, scrubbing down with water etc. complete complete all as specified and directed by Engineer-in-Charge.

M&L Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following types complete all as specified and directed by Engineer-in-charge.

M&L for rendering 15 mm thick in CM 1:4 on brick work or concrete work surfaces including finished even & smooth without using extra cement complete all as specified and directed by Engineer - in - Charge.

M&L 15 mm thick rendering in CM 1:6 on brick / concrete wall surfaces including finished even & smooth without using extra cement complete all as specified and directed by Engineer - in - Charge.

M&L, 5mm thick rendering in CM 1:3 on fair faces of concrete surfaces as on ceilings finished even and smooth without using extra cement complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil emulsion distemper, over a coat of chalk whiting with putty complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered surfaces of walls with putty and applying two coats of cement based paint over a coat of white wash complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of old decorated wall surfaces by brooming down or steel wire brushing,scrapping down smoke soot,moulds,moss and efflorescent salts and trading oil and greasy spots and then applying two coats of cement base paint with putty complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of old decorated plastered or un-plastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot,moulds,moss and efflorescent salts and trading oil and greasy spots and applying two coats of oil emulsion distemper complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plaster surfaces of ceiling and applying three coat of white wash complete all as specified and directed by Engineer-in-charge.

M & L for old decorated ceiling surfaces by brooming down or steel wire brushing,scrapping down smoke soot,moulds,moss and efflorescent salts and trading oil and greasy spots and then applying two coats of white wash complete all as specified and directed by Engineer - in - Charge.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty in square n. exc 0.5 sqm the each pane complete all as specified and directed by Engineer - in - Charge.

4 mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed by Engineer - in - Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of new wood and wood based surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of Pink primer complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of old wood and wood based surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint (ordinary tint) complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of old wood and wood based surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint (ordinary tint) complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide, zinc chrome primer complete all as specified and directed by Engineer - in - Charge

M&L for preparation of old steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint (ordinary tint) complete all as specified and directed by Engineer - in - Charge

S&F Galvanised steel water tubing 15 mm bore medium grade with all fittings concealed including cutting chases to brick wall/ceiling or laying in floors and making good disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

S&F Galvanised steel water tubing 20 mm bore medium grade with all fittings concealed including cutting chases to brick wall/ceiling or laying in floors and making good disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

Fixing only Galvanised steel water tubing 15mm bore with new fitting including cutting chases to brick wall /ceiling or laying in floors and making good disturbed surfaces complete all as specified and directed by Engineer-in-Charge. Note;- Serviceable GI pipe obtained Srl item No 92 shall be re-used.

Fixing only Galvanised steel water tubing 20mm bore with new fitting and fixed to walls, ceiling or laid in floorscomplete all as specified and directed by Engineer-in-Charge. Note;- Serviceable GI pipe obtained Srl item No 95 shall be re-used.

Taking down 15 mm bore Galvanised steel water tubing with all fittings complete all as specified and directed by Engineer-in-Charge.

Taking down 20 mm bore Galvanised steel water tubing with all fittings complete all as specified and directed by Engineer-in-Charge.

Dismantling and taking down water tank of capacity exc. 250 Litre but n. exc. 500 litre capacity complete all as specified and directed by Engineer - in - Charge.

S&F rotational moulded white colour polyethylene water storage tank 500 litre capacity (Cylindrical vertical with closed top) hoisted and fixed in position with necessary fittings complete all as specified and directed by Engineer - in - Charge. (Note : PVC tanks shall be ISI marked, having two layres and white colour)

S&F in repairs 15mm bib tap cast copper alloy,fancy type, chromium plated with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferule complete all as specified and directed by Engineer-in-Charge. Make: Prayag cat part no-8306 Parryware cat part no- T3504A1, Cera cat part no- HTF2001151,

S&F in repairs 15mm bore Pillar cock cast copper alloy fancy type chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engineer-in-Charge. Make:- Parryware cat part no-T3501A1, Prayag cat part No- 8304, CREA cat part No. -F3002101

S&F in repairs 15mm dia brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge. Make:- Parryware cat part no-G4636A1, Prayag cat part No- 8550, CREA cat part No. -F1005501

S&F in repairs 15mm bore angle stop cock / valve cast copper alloy, fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed by Engineer-in-Charge.Make: Prayag cat part no-8310 Parryware cat part no- T3507A1, Cera cat part no- F3002201

S&F in repairs 20mm bore angle stop cock / valve cast copper alloy, fancy type screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed by Engineer-in-Charge. Make: Prayag cat part no-8326 Parryware cat part no- T35011A1, Cera cat part no- F3002361

S & F in repairs 20 mm bore gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directrd by Engineer in charge.

S&F in repairs , 20mm bore Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe (minimum weight 210gms) complete all as specified and directed by Engineer - in - Charge.

S&F grating doom 100 mm dia of PTMT fixed complete all as specified and directed by Engineer-in-Charge. Note:- Minimum weight 25gms

S&F in repair PVC connections 15mm size with PTMT nut of length 450mm complete all as specified and directed by Engineer-in-Charge.

S&F 100mm dia bore sand cast, cast iron soil, waste and vent pipes in any length with or without ears with cement joints laid in trenches or fixed to wall complete all as specified and directed by Engineer - in - Charge

S&F 75mm dia bore sand cast, cast iron soil, waste and vent pipes in any length with or without ears with cement joints laid in trenches or fixed to wall complete all as specified and directed by Engineer - in - Charge

S&F 100mm bore cast iron Bends (any radius),with duck's foot or heel rest diminishing pieces or tapers (larger bore measured) complete all as specified and directed by Engineer-in-Charge.

S&F 75mm bore cast iron Bends (any radius),with duck's foot or heel rest diminishing pieces or tapers (larger bore measured) complete all as specified and directed by Engineer-in-Charge.

S&F 100mm bore cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches and sand cast (any radius),diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and directed by Engineer-in-Charge.

S&F 75mm bore cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches and sand cast (any radius),diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and directed by Engineer-in-Charge.

S&F 100mm bore cast iron sockets, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches and sand cast (any radius),diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and directed by Engineer-in-Charge

S&F 75mm bore cast iron sockets, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches and sand cast (any radius),diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and directed by Engineer-in-Charge

M&L 110 mm PVC (SWR) pipes single socked in any length with rubber ring joints, fixed to walls all as specified and directed by Engr-in-charge.

S&F 110mm bore PVC (SWR) bends of with oval access door complete all as specified and directed by Engineer-in-Charge

S&F in repairs, cromium plated shower rose of size 125mm with or without shivel joints including fixing to pipe or union complete all as specified and directed by Engineer - in - Charge.

S&F in repairs, sinks with drainage board made of stainless steel 1 mm thick for kitchen with plugs, washers and waste coupling 40mm bore dia of discharge pipe , waste pipe plain 90cm long suitable for sink waste coupling, waste jali including making grooves , fixing properly or bedding in cement mortar to walll or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer - in - Charge.

S&F in repairs vitreous china wash down water closet pan (Pedestal pattern), white excluding fixing bolts, flushing cistern and flush pipe, including plastic water closet seat, black cosed pattern with flat bottom, and cover and mild steel chromium plated hinging device complete all as specified and directed by Engineer - in - Charge.

S&F in repairs water closet vitreous china squatting pan "Orrisa pattern" size 580mmx440mm white with integral foot rests (Excl flushing cistern) complete all as specified including CI 'P' trap all as specified and directed by Engr-in-charge.

S&F in repairs 10 litre capacity low level PVC valve less, syphonic action type flushing cistern, white, with inlet, ball valve, float and handle including bracket and provision of flush pipe of polythene of high density or PVC, 15mm dia and 450 mm long complete all as specified and directed by Engineer-in-Charge.

S&F in repairs vitreous china wash hand basin white, flat back size 550x400mm including brackets, waste coupling 32mm dia of brass Chromium plated, 15mm dia pillar tap of cast copper alloy with capstan head screwed down, high pressure, with or without letter "Hot or Cold" with long screwed shank and fly nuts, 32mm dia, waste pipe low or high density polyethelene of pressure rating 6 Kg/Sqm and PVC connection with PTMT nuts of 15mm dia and 450mm long cutting for and pinning in end of brackets or erecting stand etc. complete all as specified and directed by Engineer - in - Charge.

S&F in repair vitreous china toilet paper holder fixed with screws complete all as specified and directed by Engineer - in - Charge

S&F in repair vitreous china white soap dish 160x160x90 mm fixed with screws complete all as specified and directed by Engineer - in - Charge

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 18cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engineer - in - Charge

S&F corner glass shelf shelve complete all as specified and directed by Engineer - in - Charge

Demolition of brick work built in cement mortar or cement lime mortar complete all as specified and directed by Engineer - in - Charge

Demolition of cement concrete in ground floor and paving n. exc. 15cm thickness (below or above ground level) of any description complete all as specified and directed by Engineer-in-Charge.

Demolition of reinforced cement concrete of any description and in any position not other wise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed by Engineer-in-Charge

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer - in - Charge.

Dismatiling brick tiles or terracing tiles, single layer on roofs complete all as specified and directed by Engineer - in - Charge.

Dismantling galvalume sheet (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed by Engineer - in - Charge.

Dismantling Wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed by Engineer - in - Charge.

Demolation Mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified and directed by Engineer - in - Charge.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed by Engineer - in - Charge

S&F in repairs stainless steel plate rack 600x750x250 mm thickness of sheet 1 mm thick complete all as specified and directed by Engineer - in - Charge.

S&F magic eye in main door for security purpose complete all as specified and directed by Engineer - in - Charge.

S&F iron cloth hanger for bathroom and bedroom complete all as specified and directed by Engineer - in - Charge.

M&L for Water proofing treatment to RCC sunken slab (not exceeding 45cm depth of sunken) as specified below complete all as specified and directed by Engineer-in-Charge:- (a) applying 15 mm plaster in CM 1:3 with WPC on raised verticle surface (b) Cleaning the surface with wire brush/coir brush, removing lose material like dust particles, dirt etc. (c) Creating fillet coving of 50x50 mm with polymer modified mortar on the junction of slab and walls (d) Apply first coat of two component modified polymer coating on the horizontal and verticle surface (e) Provision of glass fiber mesh of 2 x 2 mm immediately on above coating (f) Apply second coat of two component modified polymer coating after 72 hrs (g) Cement concrete 1:4:8 thickness 50mm over the coating as per requirment (h) Joining the saintary pipes with the water proofing tape having bridging ability of more than 1.5 mm (j) Filling the gap between the wall opening and saintary pipe with non shrink cementatious grout complete all as specified and directed by Engineer-in-Charge. Make:- Dr. Fixit/Fosroc/STP/Sika Note: (i) PCC filling in sunken portion will be measured seperately.

M&L for Roof treatment to RCC roof as follows :- (a) Cleaning the roof surfaces thoroughly using wire brushes to remove sharp projections,cleaning joints,washing,drying and removing all dirt/dust to receive concrete padding/ plaster etc complete. (b) Providing 15 mm thick screed bed or bedding layer of cement mortar (1:4) with WPC , finished even and smooth without using extra cement. (c) Providing one coat of approved bituminous primer @ 100 gms per sqm, over dried plastered surface. (d) Laying 3 mm thick APP based polymeric membrane,(mineral finish) minimum weighing 3 Kg/Sqm reinforced with non woven polyster fabric (weight not less than 150 gms/Sqm) by torch application. The overlapping while torching shall be 75 mm on longitudinal direction and 100 mm on the transverse direction complete all as specified and directed by Engineer-in-Charge. Makes:-STP, Dr Fixit/Pidilite,Texsa India Ltd Notes: (i) All joints and change in directions should be covered with cement mortar (1:3) mixed with SBR latex @ 200 ml/bag of cement/ as per site requirement and cured well before laying membrane by torching. (ii) All angles and abuttments should be sealed well with extra care to ensure full bondage. (iii) Water proofing treatment shall be got carried out by approved authorised applicator of manufacturer only.The name of firm shall be got approved from GE before carrying out the work. (iv) The independent testing of membrane for technical parameters given in particular specifications shall be carried out from Govt approved labs having fascilities for testing of membrane. (v) The guarantee of treatment shall be for minimum 10 years reckoned from date of completion of whole work

Excavation in trenches in n.exc. 1.5 m wide & n. exc. 1.5m in depth in soft/ loose soil for laying of cable complete all as specified and directed by Engineer - in - Charge

Returning filling in, including spreading levelling, watering and well ramming in layers not exc. 25 cms thick in soft/ loose soil complete all as specified and directed by Engineer - in - Charge.

Removing excavated material n. exc. 50 m & depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed by Engineer - in - Charge.

Supply & filling/ laying a layer of dry coarse sand 8 cm thick before laying ofcable and 15 cm thick after laying of cable complete all as specified and directed by Engineer - in - Charge. Note:- After punning drain 18 cm will be measured for payment.

M&L for brick protection layer with one brick wide using sub class ‘B’ bricks laid flat across the cable complete all as specified and directed by the Engineer in charge.

Supplying, laying and testing 25 Sqmmx4 core XLPE insulated, heavy duty electric cable with aluminium conductor 1100 V grade conforming to IS-7098 laid in trenches/ducts/fixed on poles wall/ laid under roads/paths/ drain/ culverts or passing through pipes complete all as specified and directed by engineer in charge.

Taking down copper/aluminium point wiring (light,fan,socket or power)complete including fixture and fittings such as switches& sockets and removing materials for taking credit complete all as specified and directed by Engineer-in-charge.

M&L for concealed conduit point wiring complete with cable 1.5 sqmm(Nominal area) FRLS PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC conduit pipe medium grade 20mm bore,pipe hooks,elbows,junction covers and junction boxes, after cutting in wall chasing for conduits and sinking's for sunken cast iron /pressed steel terminal boxes 60 mm deep of suitable length and 1.2 mm thickness for mounting switches, sockets, fan regulator with 3mm thick plastic laminated seat cover fixed with brass screws and cup washers, duly grouting and painted with red oxide metal primer and making good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth contuity conductor along with point wiring of 1.5 sqmm copper FRLS PVC insulated cable for point controlled by one way switch and connected to common earth dolly, complete all as specified and directed by Engr-in-charge.

All as described in Srl item No -144 here in before but for one three pin socket outlet 5 Amp on same board with other switches complete all as specified and directed by Engineer - in - Charge.

All as described in Srl item No -144 here in before but for one switch socket combination 5/6 Amps on independent board complete all as specified and directed by Engineer - in - Charge.

All as described in Srl item No -144 here in before but for one light point controlled by two ways switches complete all as specified and directed by Engineer - in - Charge.

All as described in Srl item No -144 here in before but for call bell point complete all as specified and directed by Engineer - in - Charge.

M&L for concealed conduit point wiring complete for light /fan with cable 2.5 sqmm(Nominal area) FRLS PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC concealed conduit ( medium quality ISI marked) pipe medium grade 20mm bore,pipe hooks,elbows,junction covers and junction boxes, after cutting in wall chasing for conduits and sinking's for sunken cast iron /pressed steel terminal boxes of suitable length and thickness for mounting switches, sockets, fan regulator with 3mm thick plastic laminated seat cover fixed with brass screws and cup washers, duly grouting and painted with red oxide metal primer and making good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth contuity conductor along with point wiring of 2.5 sqmm copper FRLS PVC insulated cable for for one switch socket outlet 3 pin 15 Amps on independent board with complete all as specified and directed by Engineer - in - Charge.

S&F angle holder insulated body with back plate for conduit fittings complete all as specified and directed by Engineer - in - Charge.

S&F switch piano flush type 5/6 Amp single pole one way complete all as specified and directed by Engineer - in - Charge

S & F bell push flush type 5 Amps complete all as specified and directed by Engineer - in - Charge

S & F electronic bell AC 230 volt single pole ding dong type complete all as specified and directed by Engineer - in - Charge

S&F Socket outlet 5 pin 5 Amps flush type complete all as specified and directed by Engineer - in - Charge.

S&F switch socket combination 5 pin, 5/6 Amps flush type complete all as specified and directed by Engineer - in - Charge

S&F Switch socket combination 2 in 1, 6 pin , 15/16 Amp flush universal type all as spd and directed by Engr in charge.

S&F in replacment MCB ‘B’ series type suitable for 240 volts, AC supply 5 to 40 Amps , single pole with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S&F in repairs MCB ‘B’ series type suitable for 240 volts, AC supply 5 to 40 Amps, S P & N with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S&F in repairs sheet metal enclosure for double door DB's made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 8 ways, 240 Volts, 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

S&F in repairs sheet metal enclosure for double door DB's made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 12 ways, 240 Volts, 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

S&F ceiling rose, surface bakelite 65x50 mm three terminals complete all as specified and directed by Engineer - in - Charge.

M & L for Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried in ground (earth pit not less than 2.25 Mtr deep below normal ground level with top edge of the plate not less than 1.5 Mtrs below normal ground level, connecting to the Galvanised iron earth lead 4 mm dia GI earth wire, by means of bolts, nuts check nuts and washers of galvanised iron and protection by provision of GI medium grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B1 using 20mm graded stone aggregate with 40mm thick cover of RCC (1:2:4) reinforced with XPM (wieght not less than 4gs/Sqm) and frame of angle iron 25mm x 25mm x 6mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape, GI light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed on top edge of earth plate common salt and charcoal filling test point made out of 40mm x 8 mm FI with fixing arrangements, funnel, wire mesh and earth work in hard dense soil, returning filling in and removal of surplus soil to a distance not exceeding 50 Mtrs all as per electrical Plate No.3 of SSR Part I and connecting to earth test point including taking our unserviceable earthing with all acessories all as specified or indicated including testing on completionall as specified and directed by Engineer - in - Charge.

S&F in replacement sub-main wiring with two single core cables PVC insulated and un-sheathed 6 sqmm (Nominal Area) FRLS stranded copper conductor drawn and including steel dia "medium quantity" PVC conduit including 6.00 Sq mm (Nominal Area) copper cable as earth continuity conductor after chasing in wall and making good the disturbed surface and white wash or existing colour, necessary junction box and cover including necessary connections, PVC flexible pipes are used in pannel board while connecting the cable complete all as specified and directed by Engineer - in - Charge.

S&F stepped type,single socket fan regulator not less than 120 watt for ceiling fan 1200/1400mm sweep complete all as specified and directed by Engineer - in - Charge

S&F Exhaust fan with high speed noiseless motor of size 250-300 mm sweep,5 star rating heavy duty metal body by grouting both ends in wall upto required length and making hole of suitable size in wall, making good the existing surface and connecting with ceiling roses with and including flexible cable 3 core copper conductor of size 24/.2 mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan of suitable length with frame. louvers, nuts, bolts etc. including making good disturbed wall in CM(1:4) complete all asspecified and directed by Engineer - in - Charge. Make- Crompton/Bajaj/Havell's/Orient

Supplying, laying, jointing and testing and commissioning in replacement of factory made feeder pillar box of 0.75mx0.60m x0.45m outdoor type pedestal mounting approx height 0.45 m from ground level totally enclose dust & vermin proof, doublr shutter, front and back opening including PCC 1:3:6, Type C-1 for pedestal of suitable size including provision of incoming & outgoing cable with glands, made with MS sheet of 3.15 mm thick & dust proof busbar chamber, comprising aluminium bus bar 3 Nos phase of size 20x10 mm for neutral 10x10 mm hinged sectional door with locking arrangement, copper conductor with PVC insulated cable lugs etc and duly powdered coated complete all as specified and directed by Engineer-in-Charge (Make : Hanson, ABB, Superteck, Power System & Control)

S&F in replacement MCB protected Socket -25Amps with plastic box and plug top vertical Din rail mount type suitable to operate at 240V current rating range 25A , 50Hz 1Ph, complied IS specification 13032 & 8623 complete all as specified and directed by Engineer - in - Charge.

S&F in replacement extruded aluminium LED batten channel 20 watt having input voltage AC90-300V, 50Hz, 6500K, with white acrylic cover tube light fitting wall mounted complete with rod, driver and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connector complete all as specified and directed by Engineer - in - Charge. Make :-Havells cat part No. LUMILINEPLUSBS20WLED865SPCSS, Bajaj cat part No. BCLSBAL 20W CW, Crompton cat part No. CCS-100-20-65-HL2-DP-NWH

S&F LED lamp 9 W for angle holder complete all as specified and directed by Engineer - in - Charge.

S&F in repairs water tight bulk head fitting, comprision of connector galvanised cast iron back plate, weather proof enamelled gallery, glass well and including 10 watt LED lamp complete all as specified and directed by Engineer-in-Charge. Make :-Havells cat part No. HEXAFT10WLED857SSYMBOPC, Bajaj cat part No. BIBWP 10W LED, Crompton cat part No. LBHP-10-CDL

S&F recess mounting 2x2 feet 36 watt LED luminaire with powder coated CRCA housing with LEDs, seamless front frame with high transmission acrylic cover and fixed electronic driver (surge protector ) complete all as specified and directed by Engineer - in - Charge . Make :-crompton cat part No. LCTLRNE-36-FO-CDL or equivalent make in Bajaj , havells

S&F in replacement security light fitting LED TYPE 25 watt with all necessary accessories, Clear transparent acrylic cover, prewired suitable to operated on 230 volt 50 HZ AC & Supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 35 mm bore “light grade” brackets 2 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed by Engineer - in - Charge. Make :-Havells cat part No. ENDURAPEARLSL25WLED757SASYTOPCMP, Bajaj cat part No. BRLEP 25 W, Crompton cat part No. LSTS-25-CDL-M

S & F in replacment meter box of size (0.9m x 0.9 m x 0.2 m) thickness 2.25 mm double door, single opening with lock arrangement suitable for fixing 04 electric meter & VTPN DB box with two single core PVC copper conductor unsheathed wire multistandred 4 sqmm, and fixing in wall with suitable cutting, including good the disturbed surfaces as per existing complete all as specified and directed by engineer in charge.

S&F switch piano flush type 5/6 Amp single pole two way complete all as specified and directed by Engineer - in - Charge

Note : Notes : (i) Amount of credit for retrieved materials is mentioned in Sch 'A' Section-II of tender documents in pdf form which will be deducted while acceptance of tender offline.

M/S KARNI CONSTRUCTION COMPANY

M/s Durga Constructions Company

M/S BUDHRAM BISHNOI