(1) Work of installing poles in 33 KV line under 33/11 KV substation Mandi Samiti 2) Work of changing the pole in 33 KV line of 33/11 KV substation Jansath Road 3) Work of changing the pole in 33KV line of 33/11 KV sub-station TP Nagar (Muzaffarnaga

1. Supply of following material G.I. Angle (65×65×6)mm

G.I. Channel (125×65)mm

G.I. Channel (100×50)mm

M.S. Earthing Rod

V Type Cross Arm 33 KV

Stay Sets (20x1800) mm

Stay wire G.I 7/8 SWG

Cross Arm Holding clamp for PCC Pole 9 M + S.T. Pole 11 M long & 13M long

Holding Clamp for top Channel, Dropper Channal & Bracing

F Bracket for 33 KV

E Bracket for 33 KV

Danger Board with clamp for PCC Pole 9 M + S.T. Pole 11 M long & 13M long

Number Plate with clamp for PCC Pole 9 M + S.T. Pole 11 M long & 13M long

Aluminum Binding wire

P G Clamp Dog to Dog

Barbed wire

Red Oxide Paint

Aluminium paint

M.S. Bolts Nuts & Washers

Earth wire clamp with Nut & Bolts

Concreting of support 13 Mtr STP

Stone pad (300×300×75)mm

Safe carriage Following Item with loading & unloading at both ends respectively. (under jurisdiction of PVVNL) a) Steel Tublar Pole SP-70 13M (Bottom Portion Galvanized)

b) 33 KV Pin Isulators (Polymer)

c) Disc Insulators B&S 7000 Kg. (Polymer)

d) Disc Fittings B&S for Dog 70 KN (Polymer)

Erection of Following material A- Erection of support after excavation of foundation pit in mix soil/normal soil/soft & hard rock and its back filling and leveling etc. The size of the pit will be (900×600)mm and having depth of 1/6th of the full length of the support & Erection of support. The work includes carriage and handling of supports from site store to pit site. (i) 13 M Long STP, SP-70 Round Pole

B- Fixing of all clamps, Cross Bracing Sets 3.5 Mtr. from M.S. Angle 65×65×6mm/50×50×6mm & other accessories on the supports as per drawing. Work includes cutting of holes and providing M.S. Bolts of 16×40mm size in the middle of cross bracing with 1 no. spring washer. The work also includes carriage & handling of accessories from sectional store to pit site as well as any fabrication work if required. (i) Single Pole (a) 13 M Long STP, SP-70 Round Pole

(ii) Double Pole (b) 13 Mtr STP, SP-70 Round Pole

Grouting of stay rods (20×1800)mm including all work of excavation, cement concrete in size (0.60 × 0.60 × 0.30)m in ratio 1:4:8 cement, sand, 40mm brick ballast) as per drg. including back filling, proper ramming etc and fixing tightening & nozzling of stay wire with stay rod with the poles of required tension as per drawing.

Grouting of supports in CC 1:4:8 (Cement, sand & 40 mm brick ballast) Grouting will be done in the block of size (450×450)mm ×1/6th of full length of the support, up to ground level, 300 mm plinth above the ground level with C.C. 1:3:6 (Cement, Course sand and Stone grit) with muffing as per drawing, work includes back filling and proper ramming. (i) 13 M Long STP, SP-70 Round Pole

Earthing of supports with MS earth Rod of (20×2500)mm long including excavation of pit and driving M.S. Rod 3.0 M apart from support and 0.5m below the ground level and connecting below the earth electrodes with the help of G.I. wire no. 8 SWG and earthing lugs.

Providing & fixing of danger board at each location as per specification of the drawing with clamps etc.

Painting of following supports/structures with 2 coats of synthetic enamel paint after one coat of ready mix primer including cost of all material, as well as rubbing/cleaning of surface as required for proper completion of work. Painting will be done by post office red paint from top to cross arm and remaining by Aluminium paint. (a) 13 Mtr, SP-70 Poles including all channels/X-Arms/Clamps etc. (i) Single supports

(ii) Double supports (b) 13 Mtr STP, SP-70 Round Pole

Wrapping of barbed wire on 33 KV PCC Poles/SP-55 ST & SP-72 ST Poles as anti-climbing device for a length of 0.9 Mtr., wire pitch/gap 13mm and fixing upper and lower end keeping lower end at a height of 2.75 Mtr. from the ground complete with supply and fixing of lower end & upper end clamps made of M.S. Flat 40×5mm complete with nuts & bolts & all other required material.

Numbering of each supports by preparing background with dark yellow paint in the size of 150mm dia and writing support number 100mm high with black paint.

Material required Local store to Store ESCMZN. MS Scrap

Fixing of Stone Pad (300×300×75)mm

Hi-tech power transmission