138WE/L-177/2025-26

Demolition of cement concrete (un reinforced ) in ground floors and pavings not exc 15cm thick (below or above ground level) and removing debris off the premises complete all as specified and as directed by Engr-in-Charge.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for and removing debris off the premises, complete all as specified and/or as directed by Engr-in-Charge.

Dismantling wall and ceiling boards (Fiber, pulp, insulation, blankets etc.) any thickness including covered fillets and supporting members, complete all as specified and/or directed by Engr-in-Charge.

Dismantling unframed wooden fillets, rails, posts, rafters, purlins, grids for ceiling & wall panelling etc. under 40 sqcm in section, complete all as specified and/or directed by Engr-in-Charge.

Demolition of precast cement concrete block walling built in cement mortar including all quoins, arches, pillars etc. complete all as specified and/or directed by Engr-in-Charge.

Taking down cement plaster on brick/ PCC block or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc., complete all as specified and/or as directed by Engr-in-Charge.

Taking down chowkat or frame with shutters (without taking off shutters from the frame) not exc 1.5 sqm each, any type of door (wooden, aluminium & steel etc.) complete all as specified and/or as directed by Engr-in-Charge.

Taking down chowkat or frame with shutters (without taking off shutters from the frame) exc 1.5 sqm but not exc 4 sqm each, any type of door (wooden, aluminium & steel etc.) complete all as specified and/or as directed by Engr-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden panes or stone, concrete or brick surrounds, glazed with oil putty or fixed with beads complete all as specified and/or directed by Engr-in-Charge.

Dismantling plain or corrugated steel/fibre sheeting any gauge or thickness including nanital or similar pattern complete all as specified and as directed by Engr-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for angle iron or flat iron as in post and guard bars or grating, complete all as specified and/or directed by Engr-in-Charge.

M&L for 9mm thick prelaminated particle board medium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with screws to timber frame work as in wall panelling, shelves/boarding complete all as specified and as directed.

M&L for 9mm thick prelaminated particle board medium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with screws to timber frame work as in ceiling, complete all as specified and as directed.

M&L for 2nd class soft wood clean sawn as in battens for grids of ceiling & lining fixed with nails exc 13 sqcm and not exc 25 sqcm in section, complete all as specified and directed by Engr-in-Charge

M&L for 2nd class soft wood clean sawn as in beading for edges of ceiling, lining or wooden flooring work fixed with nails exc 6 sqcm and not exc 13 sqcm in section, complete all as specified and/or as directed by Engr-in-Charge.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection finished fair and even, complete all as specified and/or as directed by Engr-in-Charge.

M&L for forming Contraction (Dummy) joints 65 mm deep x 10mm wide, filled with sealing compound Grade 'A' in plinth protection, complete all as specified and/or as directed by Engr-in-Charge.

M&L for PCC 1:4:8, type D2 (using 40mm graded crushed aggregate) as in mass concrete and filling of foundation, complete all as specified and/or as directed by Engr-in-Charge.

M&L for precast solid blocks in cement concrete 1:3:6 type C-1 (20mm graded crushed stone aggregate) as in block masonry, exc.10cm in width and set in cement mortar 1:6, complete all as specified and/or directed by Engr-in-Charge.

M&L for 10mm thick rendering on fair faces of block masonry / brick wall works finished even and smooth without using extra cement in cement mortar 1:6 complete all as specified and/or directed by Engr-in-Charge.

M&L for 15mm thick rendering on other than fair faces of brick works in two layers 10mm & 5mm thick using water proofing compound for outer layer of 5mm, finished even and smooth without using extra cement in cement mortar 1:4 including mixing of liquid water proofing compound as per manufacturer's instructions complete all as specified and as directed by Engineer-in-Charge. Note : WPC will be measured and paid separately.

Supply only integral liquid water proofing compound. Make : Pidilite/Sika/Asian paints.

M&L for preparation of new plastered wall surfaces of any description and applying two coats of cement based paint over a coat of primer complete all as specified and/or as directed by Engr-in-Charge.

M&L for preparation of new plastered wall surfaces of any description and applying three coats of white wash complete all as specified and/or as directed by Engr-in-Charge.

S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and/or as directed by Engr-in-Charge.

M&L for mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified and/or as directed by Engr-in-Charge.

S&F 35mm thick 2nd class hard wood plain framed panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, complete all as specified and/or as directed by Engr-in-Charge.

S&F 2nd class hard wood factory made 35 mm thick Glazed and Skelton shutter, open and prepared to receive the glass, gauze etc. (without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc. (Glass / Wiremesh should be measured separately) complete all as specified and/or as directed by Engr-in-Charge.

M&L for preparation of new untreated wood or wooden based surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and/or as directed by Engr-in-Charge.

M&L for preparation of old treated wood or wooden based surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and/or as directed by Engr-in-Charge.

S&F mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified and/or as directed by Engr-in-Charge.

M&L for sheet glass 3mm thick ordinary quality and glazing with oil putty or wooden beads in square not exc 0.50 sqm in each pane complete all as specified and as directed.

S&F 150mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and as directed.

S&F 100mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and as directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed.

S&F 100 mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed.

S&F floor door stopper (length of cover plate) 150mm long aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor complete all as specified and as directed.

S&F 75mm long aluminium anodized, butt hinges of extruded section complete all as specified and as directed.

S&F 100mm long mild steel, butt hinges, medium weight cold rolled complete all as specified and as directed.

S&F 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and/or as directed by Engr-in-Charge.

M&L for 25 mm thick PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in sub base of floor complete all as specified and/or as directed by Engr-in-Charge.

M&L for glazed ceramic coloured tiles in vertical surfaces of size 350x250x7mm / 450x350x7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including rendering 10 mm thick in cement mortar (1:4) for dado/skirting tiles, complete all as specified and/or as directed by Engr-in-Charge.

M&L for Non - skid coloured Ceramic joint free tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm, in floors over & including 15mm thick screed bed or bedding layers in cement mortar 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and/or as directed by Engr-in-Charge.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar, complete all as specified and/or as directed by Engr-in-Charge.

M&L for machine cut kota stone slab flooring 20-25mm thick over and including cement screed bed 20mm thick in cement mortar 1:6, set and jointed in neat cement slurry, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and/or as directed by Engr-in-Charge.

M&L for 75 mm thick PCC 1:4:8 type D2 (using 40mm graded crushed stone aggregate) as in sub base of floor complete all as specified and/or as directed by Engr-in-Charge.

M&L for preparation new steel surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed

Demolition of reinforced cement concrete of any description and any position not otherwise specifically provided for, complete all as specified and/or as directed by Engr-in-Charge.

M&L for form work to soffits of suspended slabs, flat type such as roof, floor slabs, landings etc not exc. 200mm thick (horizontal or sloping), rough finished concrete surfaces, complete all as specified and/or as directed by Engr-in-Charge.

M&L for reinforced cement concrete 1:2:4, type B1 (20 mm graded stone crushed aggregate) nominal mix as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs etc. complete all as specified and/or as directed by Engr-in-Charge.

M&L for TMT bars, 10 mm dia and over, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9 mm dia), complete all as specified and/or as directed by Engr-in-Charge.

M&L for chequered cement concrete tiles (glazed) 30cm x 30cm x 20mm thick, set, jointed and pointed in neat cement slurry in floors polished with grey cement & pigments, laid over 20mm thick cement screed base (1:6), complete all as specified and/or as directed by Engr-in-Charge.

S&F in repair 19mm dia mild steel, chromium plated curtain rods, with brackets, end bulbs, complete all as specified and/or as directed by Engr-in-Charge.

S&F mild steel rolled sections in main and cross beams, hip and jack rafters; purlins where connected to common rafters running rails and guids for sliding doors; fixed with angle cleats or other connecting plates and similar work conforming to Fe-290, Gde-E-165, complete all as specified and/or as directed by Engr-in-Charge.

S&F 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with coach screws and washers in roofs, walls etc. with grade of zinc coating 275, complete all as specified and/or as directed by Engr-in-Charge.

All as per Ser item No 56 above, but except sheeting.

M&L for preparation of old steel surface of any description over 10cm in width or girth and applying two coats of synthetic enamel paint, complete all as specified and/or as directed by Engr-in-Charge.

Taking down carefully copper/ aluminium point wiring (light, fan, socket and power point) including complete fittings such as switches, ceiling rose, regulators, socket etc. and removing material from site and making good disturbed surfaces of walls, floors/ceiling to match the existing surface, complete all as specified and/or as directed by Engr-in-Charge.

Point wiring complete with 1.5 sqmm nominal area of copper conductor multi stranded PVC insulated and unsheathed 1100 volts FRLS cable drawn through & including PVC casing & caping with standard accessories such as elbows, tees, junctions etc. and PVC moulded terminal box with top cover of including PVC insulated unsheathed solid 1.5 sqmm copper conductor FRLS cable as continuous earth lead all as specified and directed for the following:-

One light point controlled by one way switch.

One switch socket outlet 6 Amps, 230 volts point on independent board.

S&F switch piano flush button single pole 6 Amps 230 volts one way complete all as specified and directed.

S&F socket outlet two in one 5 pin 6 Amps flush type.230 volts complete all as specified and directed .

S&F ceiling rose, surface bakelite three terminals complete all as directed.

S&F in replacement of sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 8 Ways all as specified and directed.

S&F in replacement of sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 6 Ways all as specified and directed.

S&F MCB SPN 63 Amp 240 Volts AC ISI marked complete all as specified and/or directed by Engr-in-Charge.

S&F MCB SP 6-32 Amps. 240 Volts 50 HZ complete all as specified and/or directed by Engr-in-Charge.

S&F in replacement LED light fitting 1X20 W, 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and/or as directed by Engr-in-Charge. Make-Havells /Crompton/ Bajaj.

S&F LED light fitting 1x9W/1x10W bulk head luminaires including LED light driver, holders connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and directed. Make-Havells/ Philips/Crompton/ Bajaj.

S&F in replacement of lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendent fittings including copper cable to hang to a desire length, complete all as specified and directed.

S&F in repair LED lamp 12 Watt, complete all as specified and/or as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth for laying of pipe, cables etc. and getting out in soft / loose soil, complete all as specified and directed.

Returning, filling in including spreading leveling watering and well ramming in layers not exc. 25 cm thick complete all as specified and directed. (Surplus soil if any shall not be removed but left over the trench).

Removing surplus soil to a distance not exc. 50m and depositing where directed at a level not exceeding 1.5 Mtr above the starting point complete all as specified and directed.

Material & labour for sand cushioning with clean dry sand to cables with layer of sand 8 cm before laying of cable and 15 cm thick after laying of cable complete all as specified. Note : For payment purpose punned thickness of 18 cm shall be measured against spread thickness of 23 cm as mentioned in para 19.75 of SSR part-I.

Material & labour for providing PCC cable cover class LV type-I of size 250x150x40mm laid in perpendicular to the cable abutting each other all as specified and directed at site.

Supply & laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volt grade of cross sectional area 70 Sqmm 3.5 Core complete all as specified and directed.

Supply & laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volt grade of cross sectional area 50 Sqmm 3.5 Core complete all as specified and directed.

Supply & laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volt grade of cross sectional area 120 Sqmm 3.5 Core complete all as specified and directed.

Supply and laying in replacement XLPE insulated, armoured heavy duty electric cable with aluminum conductor, 11000 volt grade of cross sectional area 10 Sqmm 2.0 Core complete all as specified and directed.

Supply and fix in replacement on load change over of 160 A with enclosure complete all as specified and directed.

Supply, installation, commissioning and testing of LT panel board outdoor type 60 cm from ground to bottom of pillar box, front door with locking arrangement with duplicate keys including PCC foundation and connecting LT panel cubical flush pattern type made of 3.15mm thick MS sheet with angle iron base frame of size 50 x 50 x 6 mm for mounting of panel, dust proof welded steel structure with TPN bus bar 400 Amps rating capacity mounted on insulators including painting of panel with two coats of synthetic enamel paint over a coat of red oxide primer having IP-54 and confirming to IS-8623 and including following accessories :- INCOMING MCCB 320 Amps 4 pole, with short circuit and earth fault protection with earth module breaking capacity 35 KA-01 No OUTGOING (a) MCCB 200 Amps 4 pole, with circuit and earth fault protection with earth module breaking capacity 35 KA-01 No (b) MCCB 160 Amps 4 pole, with short circuit and earth fault protection with earth module breaking capacity 35 KA-01 No (c) MCB SPN 32 Amps, 240 Volts, 50 Hz ‘C’ curve type-06 Nos (d) MCB SPN 63 Amps, 240 Volts, 50 Hz ‘C’ curve type – 06 Nos Note: - (i) All AMCBs/instruments/MCBs/Bus Bar shall be housed in a separate housing with on-off latches in the housing.

Supply and fixing in repair Steel tubular swaged street light poles complete with pole arms 1.2 m & cast iron base plate ,finial taper plug,bolts,nuts and screws as specified type 410 SP-31 9.0 mtr long and painting with two coat of aluminium paint over one coat of primer on exposed surface of pole all as specified and directed by Engr-in-Charge. (NOTE- Excavation & PCC will be measured and paid separately).

M&L for PCC 1:2:4, type B1 (using 20mm graded crushed aggregate) as in mass concrete and filling of foundation, complete all as specified and/or as directed by Engr-in-Charge.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

Supply and fix FRP type looping box 100x100mm including necessary arrangements to fix looping box with the suitable nuts, bolts washers flat iron etc comprising of one MCB 5 to 30 Amps 10 KA, C series complete all as specified and directed.

Supply & fixing in replacement of tubes light grade of size 80 mm bore galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified.

Material & labour for Earthing complete with galvanized steel earth plate 600x600x6 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 meters below normal ground level, connected to galvanised strip 25 mm x 4 mm dia as earthing lead by means of bolts, nuts, check-nuts, and washers of galvanised iron or steel besides welding at all joints as shown in drawings and including excavation and earth work, GI pipe light grade 40 mm bore for protection of GI strip from earth electrode to and including the earth test point of galvanised Iron/steel of size 600x600x6 mm, supplying and laying charcoal stone aggregate) chamber and mild steel angle iron frame 40x40x3mm and RCC cover 40 mm thick (1:2:4) type B1 using 20 mm graded crushed stone aggregate reinforced with 8 mm dia TMT bars @ 75mm C/C both ways with mild steel handle 12 mm dia, PGI funnel with wire mesh, 20 mm dia GI pipe light grade all as shown in drawing. Note : (a) GI earth Strip will be measured and paid separately beyond 7.5 Mtr length, the rates of funnel with GI pipe for watering is deemed to be included in this item.

M&L for Earthing complete with galvanised steel earth plate electrode 60 cm X 60 cm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to and including 4 mm dia GI wire as earthing lead, by means of bolts, nuts, check nuts and washers of galvanised iron all as shown in electrical plate No 3 of MES SSR Part I and testing on completion including excavation and earth work in any type of soil, PCC (1:3:6) type C1 chamber, MS frame and cover 6 mm thick in cement concrete (1:2:4) type B1 reinforced with welded steel wire fabric or XPM (weight not less than 4 Kg per Sqm) with cast iron frame, funnel with wire mesh, GI watering pipe 20mm dia medium grade and lugs complete all as specified and directed.