Construction of Degree College at Neeli Nallah Udhampur (Phase- 1st).

Amount

Earth work in excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth , 1.5 mtr in width as well as 10 sqm on plan) including disposal of excavated earth, with all leads and lift complete, disposed earth to be levelled & neatly dressed (50% all kind of soils, 20% ordinary rock and 30% hard rock (Blasting Prohibited). for foundation in trench, Including levelling of ground as per the direction of engineer- in- charge

Extra for every additional lift of 1.5 M or part therefore in all kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level in 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate) 40mm nominal size crushed. incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Random Rubble masonry with hard stone from Nallah in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone agg. 20 mm nominal size) at plinth level with cement mortar 1:8 ( 1 Cement : 8 fine sand) incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete (Stone available at site)

Providing and laying in position of reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size) excluding the cost of centering, shuttering, finishing and reinforcement. All work upto plinth level. incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement. 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded crushed stone aggregate 20mm nominal size). incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Providing and laying in position cement concrete of 1:3:6 grade (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20mm nominal size) excluding the cost of centering and shuttering. All work upto plinth level. incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Brick work with common burnt clay F.P.S (non modular) bricks of class designation 75 upto plinth level in cement mortar 1:4 (1 cement : 4 fine sand). incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Providing and laying DPC 50mm thick in 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size crusher aggregate). incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Applying a coat of residual petroleum bitumen of grade VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Brick work with common burnt clay F.P.S (non- modular) bricks of class designation 75 in foundation and plinths in cement mortar 1:6 (1cement : 6 coarse sand). incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Extra for brick works in super structure above plinth level up to floor five level. incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Half Brick masonry with bricks of class designation 75 in foundation and plinth in cement mortar 1 : 4 (1 cement : 4 coarse sand) incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Extra for half brick masonry in superstructure above plinth level up to floor V level. incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Providing and laying Reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size) in suspended floors, balconies, landings and staircases having 15 degree slope. upto floor five level excluding the cost of centering and shuttering. incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete TMT bars. incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Centering and shuttering including strutting, propping etc. and removal of form work for :-

Foundations, footings, bases of columns.

Suspended floors, roofs, landings, balconies and access platforms.

Columns, pillars, piers, abutments, posts and struts.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Edges of slabs and breaks in floors and walls upto 20cm wide.

Retaining walls, return walls, wall (any thickness) including attached pilasters, buttresses, plinth and string courses fillets etc.

Weather shade, chajjas, corbels etc. including edges.

Stairs (excluding landings) except spiral stair cases.

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentring at all levels, over a height of 3.5m, for every additional height of 1 mtr. of part thereof (Plan area to be measured). Suspended floors, roofs landing, beams and balconies (Plan area to be measured).

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, lead upto 50Mt & lift upto 1.50M.

Supplying and filling in plinth with fine sand under floors including, watering, ramming consolidating and dressing complete.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded brick aggregate 40mm nominal size) in R/Wall/Return Wall, columns etc. excluding the cost of centering and shuttering, all works upto floor V level. incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

6mm thick cement plaster to ceiling of mix 1:3 (1 cement : 3 fine sand). incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

15mm cement plaster on the rough side of single or half brick wall of mix in 1:6 (1 cement : 6 fine sand). incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

15mm cement plaster on the rough side of single or half brick wall of mix 1:4 (1 cement : 4 fine sand). incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

12mm cement plaster of mix 1:6 (1 cement : 6 fine sand). incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

15mm cement plaster 1:3 (1 cement : 3 coarse sand) finished with a floating cost of neat cement on the rough side of single or half brick wall. incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

18mm thick moulded cement mortar band in two coats under layer 12mm thick with cement mortar 1:5 (1 cement : 5 fine sand) top layer 6mm thick with cement mortar 1:4 (1 cement : 4 fine sand) for 4cm width. incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Extra for plastering exterior walls of the height more than 10 Mtrs from ground level for every additional height of 3 Mtrs or part thereof.

Add or deduct for plaster drip coarse / groove in plastered surface of moulding to RCC projections.

Making of grove 12mm x 10mm between brick and RCC.

Providing and laying 18mm thick Udhaypuri Green Marble /zebra black marble (area of slab over 0.5 Sqm) gang saw cut mirror polished (pre moulded and pre polished), machine cut for kitchen platform, vanity counters window sills facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels.

Providing and laying glossy finished full-body vitrified premium quality floor tiles of 60x60cm sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622 of approved make of Somany, Kajaria, NITCO and Orient make in colours and shade Ethnic-Berlinetta White, Crown White, Dacia White, Dacia Green, Dacia Pink, Dacia Ivory, Dacia Grey, Dacia Brown, Dacia Pearl, Dezzling White, Evalia, S&P Grey, S&P Brown, Ultra White, Haze Grey and Border of Royale- Crown Mint, Crown Pink, Crown Snow, Micra Brown and Radiant- Lawrence Gold, Lawrence Bianco, Lawrence Grigio, Lawernce Moka, Lawrence Jaisalmer, Nuvro Brown, Nuvaro Mocha, Nuvaro Grey, Nauvaro Nero, Nuvaro Crema, Nuvaro Bianco, Nuvaro Beige laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with matching Epoxy etc. complete.

Providing and fixing Ist quality ceramic glazed tiles conforming to IS : 13753 of minimum thickness 5mm of approved make like NITCO, ORIENT, SOMANY, KAJARIA or equivalent make in all colour, shades except burgundy, bottle green, black of any size as approved by Engineer in charge in skirting, risers of steps and dodos over 12mm thick bed of cement mortar 1:3 (1cement : 3coarse sand) and jointing with grey cement slurry @ 3.3Kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing ceramic glazed floor tiles (non-skidding) 300x300mm (thickness to be specified by the manufactures) of Ist quality conforming to IS : 13755 of NITCO, ORIENT, SOMANY, KAJARIA or equivalent make in colour such as white, Ivory, Grey, Fume Red, Brown laid on 20mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc. complete.

Providing and laying 16mm thick Granite of any colour and shape (area of slab upto 0.5 Sqm) gang saw cut mirror polished (pre moulded and pre polished), machine cut for kitchen platform, vanity counters window sills facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels.

Providing and laying 16mm thick Granite of any colour and shape (area of slab upto 0.5 Sqm) gang saw cut flamed (pre moulded and pre polished), machine cut for stairs steps and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels.

Extra for providing edge moulding to 18mm thick Granite stone counters, Vanities etc. over item No. 8.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge.

Extra for providing opening of required size and shape for wash basins/kitchen sink in kitchen platform, vanity counters and similar location in marble / stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Precast terrazzo tiles 22mm thick with graded marble chips of size upto 12mm laid in floors and landing, jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete with precast tiles on 20mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand). Medium shade using 50% white cement and 50% ordinary cement.

Precast terrazzo tiles 22mm thick with graded marble chips of size upto 12mm laid in skirting and risers of steps not exceeding 30cm in height on 12mm cement plaster 1:3 (1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles, excluding rubbing and polishing complete with tiles of medium shade using 50% white cement and 50% ordinary cement.

Chequerred precast cement concrete tiles 22mm thick in footpath and courtyard jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and cleaning etc. complete on 20mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand). Medium shade using 50% white cement and 50% ordinary cement.

Cement concrete flooring 1:2:4 finished with a floating coat of neat cement including cement slurry, but excluding the coat of nosing of steps etc. complete 50mm thick with 20mm nominal size of stone aggregate.

Cement plaster skirting (upto 30cm height) with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement 18mm thick.

Providing and fixing of 12mm thick GRC wall Cladding (Tiles) of pattern stone castle (size 4” x 10”) on exterior wall / surface. Unistone make as per the approved sample. All complete as per architectural drawings and the directions of Engineer-in-Charge.

Providing and laying integral cement based water proofing treatment including preparation of surfaces as required for treatment of roofs, balconies, terraces etc. (Make Armocreate of SWC Chryso France) consisting of (a) applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks / brick bats 25mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1:5 admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining was upto 300mm height including rounding of junction of walls and slaps. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg / sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge. (iv) Finishing the surface with 20mm thick joint less cement mortar of mix 1: 4 admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge including laying glass fiber cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300mm / sq 3mm deep. (e) The whole terrace so finished shall be flooded with water far a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by Engineer-in-charge. With average thickness of 120mm and minimum thickness at khurras as 65mm.

Providing and laying water proofing treatment (Make Armocreate of SWC Chryso France) to vertical and horizontal surface of depressed portions of W.C., kitchen and the consisting of (i) Ist course of applying cement slurry @ 4.4 kg /sqm mixed with water proofing compound conforming to IS : 2645 in recommended proportions including rounding of junctions of vertical and horizontal surface. (ii) IInd course of 20mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportions including rounding of junctions of vertical and horizontal surface. (iii) III course of applying blown or / residual bitumen applied hot at 1.7 kg per sqm of area. (iv) Ivth course of 400 micron thick PVC sheet (Overlaps at joints of PVC sheet should be 100mm wide and pasted to each other with bitumen @ 1.7 kg/sqm.

Providing and fixing on wall face unplasticised-Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. Single socketed pipes of 110mm diameter.

Providing and fixing on wall face unplasticised-PVC moulded fitting / accessories for unplasticised- rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion :-

Coupler 110mm.

Single tee with door 110 x 110 x 110mm.

Bend 87.5* 110mm.

Making plinth protection 50mm thick cement concrete 1:3:6 (1 cement : 3 course sand : 6 graded stone aggregate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth crushed.

Brick edging 7 cm wide 11.4cm deep to plinth protection with bricks of class designation 75mm including grouting with cement mortar 1:4 (1 cement : 4 fine sand).

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately) sal wood.

Providing 40x5mm flat iron hold fast 40cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing & fixing glazed shutters 35mm thick for doors, windows and clear story windows using 10Kg/Sqm (4mm thick) glass panes including stainless steel but hinges of size 75mm x 62mm x 2mm of make Kitch, Arch, Blum with necessary stainless screws in second class deodar wood.

Providing and fixing 35mm thick wire gauze shutters using galvanized M.S. wire gauge of average width for aperture 1.4mm in both direction with wire of dia 0.63mm for doors, windows and clerestory windows with hinges and necessary screws in second class deodar wood.

Providing and fixing of glass panes weighing 13.75 kg/sqm (5.5mm thick) with deodar wood fillets.

Providing and fixing of block door shutters in pine wood filling and finished with 1mm thick laminated on both sides. Door held with 4 No. hinges with necessary screws as per directions of Engineer-in-charge with deodar wood beading of 100mm x 37mm section.

Providing and fixing M.S grills of required pattern in frames of windows etc. with M.S flats, square or round bars etc. including priming coat with approve steel primer all complete (fixed to openings/wooden frames with rawl plugs, screws etc.).

Steel work welded in built-up sections/framed work including cutting hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required in gratings, frames, guard bar, ladders, railings, brackets, gates and similar work.

Providing and fixing aluminium tower bolts ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete.

Providing and fixing aluminium sliding door bolts ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. 300x16mm.

Providing and fixing aluminium handles ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete.

Providing and fixing aluminium hanging floor door stopper ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. Twin rubber stopper.

Providing and fixing oxidized M.S. hasp and staple (Safety type) conforming to IS : 363 with necessary screws etc. complete.

P/F stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc, including welded, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered including fixing accessories such as nuts, bolts, fasteners etc.

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets. 25mm dia (heavy type).

Providing and applying white cement based putty of average thickness 2mm, of approved brand and manufacture, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade new work (two or more coats) over and including priming coat with cement primer.

Finishing walls with water proofing cement paint of required shade new work (two or more coats applied @ 3.84 Kg/10 Sqm).

Applying priming coat with ready mixed pink or grey of primer of approved brand and manufacture on wood work (hard and soft wood).

Painting with synthetic enamel paint of approved brand and manufacture to give and even shade two or more coats on new work (Wood work).

Painting with ready mixed synthetic enamel paint of approved brand and manufacture in all shades to give an even shade (two or more coats) on new steel work.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions at top, bottom and sides with required PVC / neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge (glazing and panelling to be paid for separately).

For fixed portion using Powder coated aluminium (minimum thickness of powder coated 50 microns).

For shutters of doors, windows and ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately). Powder coated aluminium (minimum thickness of powder coated 50 microns).

Providing and fixing glazing in aluminium door, window, ventilator shutters and partition etc. with PVC / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item). With glass panes of 5.50 mm thickness (weight not less than 13.75 kg/sqm).

Providing and fixing 12mm thick prelaminated three layer medium density (exterior grade) particle board Grade-I, Type-II conforming to IS : 12823 bonded with phenol formaldehyde synthetic resin, of approved brand and manufacture in panelling fixed in aluminium doors, windows shutters and partition frames with C.P brass / stainless screws etc. compete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS:6315 marked for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge with brass cover plate.

Providing and fixing structural glazing on required portion of the building with aluminium section (12 gauze using 5.5mm toughen glass with all necessary fittings) as per direction of Engineer-in-charge.

Maintaining 50mm joint right from foundation to top and allowing its free moment throughout the life span of structure "Providing/Supply of Dura Board HD 100, 50mm, Premounded Compressible filler Board in Black colour manufactured by the Supreme industries Ltd. or equivalent, conforming to MORTH specifications (clause 1015), having minimum density 95 kg/cum, non staining with less than 1% water absorption and compression recovery 93% minimum as per specifications" in the joint through and through (foundation to top) in brick masonary, columns and beams.

Sealing of joint 50mm. Clean the joint both the side and apply Master Brace ADH 2200 adhesive throughly on the clean surface along the joint with spatula and thickness should be 1mm -2mm. Place the Master Seal 1930 10mm on the ADH 2200 on the both sides keeping the centre totally for free movement.

Plumbing

SUB HEAD - I : SANITARY FIXTURES

Providing & fixing of white vitreous China pedestal type water closet (European Type) with cistern (A/PHAS-100 +Cat No. 201100 + Cat No. 21054) with CP bolts, nuts, CI chair hanging arrangements, bakelite seat & cover with CP hinges & rubber buffers, CP brass screw, washer with all accessories with WC connector with Rubber Lip / Buffer and side gap filled with silicon sealant wherever required. Including brass / SS screws and washer complete including cutting, making good the walls, floors, slab wherever required as per direction of Engineer-in-charge.

Providing & fixing of white vitreous China under counter oval wash basin / circular basin (Hindware 10080) with CP brass waste assembly, CP cast brass bottle trap with extension piece (Jaquar Cat No. 769B + Parko1535 or approved equivalent), 450mm long CP copper connections pipes (Jaquar Cat No. 803B or Parko 1535 or approved equivalent), wall flanges and rubber adapters for waste connection complete including CI/MS brackets duly painted, nuts, washers, cutting and making good the walls floors wherever required as per direction of Engineer-in-charge.

Providing and fixing of white vitreous china wash basin with pedestal (Hindware Cat No. 1008 + Pedestal Cat No. 11003) with CP brass waste assembly, CP cast brass bottle trap with extension piece (Jaquar Cat No. 769B+Parko 1535 or approved equivalent), 450mm long CP copper connections pipes (Jaquar Cat No. 803B or Parko 1535 or approved equivalent), wall flanges and rubber adapters for waste connection complete including CI/MS brackets duly painted, nuts, washers, cutting and making good the walls floors wherever required as per direction of Engineer-in-charge.

Providing and fixing CP single liver extended basin mixer (height 85mm) without Popup waste system with 450mm long Braided Hoses and brass nuts with all fittings and accessories as per direction of Engineer-in-charge (Jaquar FUS 290238).

Providing & fixing white vitreous china flat back urinal with automatic flushing systems (Hindware 60021) comprising of all plumbing, electronic and electrical items, CP brass flush pipe with CP brass elbow, CP brass spreader, CP wall flange, infrared photo cells, eyes, electrically operated solenoid valve, step down transformer, equipment and any other item required to provide satisfactory functioning including necessary wall cutting/ chasing and making good, as required for urinal flushing complete as mentioned above as per direction of Engineer-Incharge.

Providing and fixing stainless steel A ISI 304 (18/8)kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required.

Kitchen sink without drain board 610 x 460mm bowl depth 200mm (Pantry).

Providing and fixing, testing and commissioning of C.P brass Sink mixer with regular swinging spout (wall mounted model) with connecting legs and wall flanges complete as required and making good as per direction of Engineer-in-charge (Jaquar Cat No. QQT 7309).

Providing and fixng C.P hand spray with lever control (health faucet) (Jaquar Cat No. ALDCHR-565) and flexible hose 1 Mtr long connection with C.P holder for hand spray complete in all respects as per direction of Engineer-in-charge.

Providing and fixing C.P brass angle valve for basin mixer and geyser points of approved quality conforming to IS : 8931 a) 15mm nominal bore (Make Jaquar FUS 29053).

Providing and fixing C.P brass robe hook (Jaquar Cat No. CAN 1191N) or approved equivalent) fixed to wall / door with plastic rawl plugs and C.P brass screws including cutting and making good the walls wherever required as per direction of Engineer-in-charge.

Providing and fixing recessed liquid soap dispenser with glass bottle (Jaquar Cat No. ACN 1135 N) as per direction of Engineer-in-charge.

Providing and fixing of Soap Dish Holder with all fittings as per direction of Engineer-in-charge (Jaquar Cat No. ACN 113 N).

Providing and fixing of Tumbler Holder with all fittings as per direction of Engineer-in-charge (Jaquar Cat ACN 114 N).

Providing and fixing Bottle Trap (Jaquar Cat No. ALD. 769L) and other ancillary fittings. Cutting and making good the walls wherever required compete as per directions of Engineer-Incharge.

Providing and fixing complete set of sanitary fixtures for handicapped toilets, Hindware Cat. No. 70002) comprising of EWC –P, Cistern, Seat Cover, Twin Flush Fittings Wash Basin 450X300, Half pedestal, 1 faucet with spatula lever, 1 hinged rail and 2 grab bars, including cutting and making good the walls and floors wherever required complete as per directions of Engineer in charge.

Providing and fixing 6mm copper backed float glass mirror MODI / SAINT-GOBAIN including 6mm thick BWR type ply board, 40mm stainless steel channel plugged to wall, hard wood treated with two coats of wood preservative etc. all complete as specified and shown in drawing complete to the satisfaction of Engineer-in-charge.

Providing and fixing C.P brass single towel rail (600mm long) of approved make complete with C.P brackets fixed to wooden cleats with C.P brass screws (Jaquar Cat No. ACN 11011NM).

Providing and fixing brass towel Ring Round with Round Flenge of approved make complete with all fittings (Jaquar Cat No. ACN 11021 BN).

Providing and fixing of glass shelf 600m long with all C.P fittings of approved quality complete item (Jaquar Cat No. ACN 11071 N).

Providing and fixing toilet paper holder with all fittings Jaquar Contienal ACN 1153 N.

Providing and fixing 15mm dia C.P brass bib cock with wall flange of approved quality conforming to IS standard (Jaquar Cat No. 29037).

Providing and fixing 15mm dia C.P brass long nose bib cock of approved quality conforming to IS : standards and weighing not less than 810 grams (Jaquar Cat No. CON-107 KN).

Providing and fixing of regular body of concealed stop cock suitable for 15mm pipe line with protection cap (Jaquar ALD-083) with exposed part angular stop cock with flange FUS 29.53.

Sub Head- II-Water Supply

Internal work:- Exposed on wall Providing and fixing of Polyethylene/Aluminum/Polyethylene (PE-AL-PE) composite Pipes as per IAPMO IGC-INDIA 308, UMC-1 TM certification marked on the pipe at the interval not greater than 1 meter with nominal pipe size with manufacturer's name or trade mark including all relevant DZR brass fittings as Female Elbows/Tees, MTC/FTC and Engineering plastic fittings with internal sealing system like Eq. elbows, Eq. tees, reducers, Straight couplers, Clamps at one meter spacing, with PAP valves and brass tank Nipples etc. Including testing of lines and joints as per Engineer in charge. Make Kitec, Maithilee and Vista.

1620 (20mm OD) pipe

2025 (25mm OD) pipe

2532 (32mm OD) pipe

Conceal Inside the walls:- Providing and fixing of Polyethylene/Aluminum/Polyethylene (PE-AL-PE) composite Pipes as per IAPMO IGC-INDIA 308, UMC-1 TM certification marked on the pipe at the interval not greater than 1 meter with nominal pipe size with manufacturer's name or trade mark including all relevant DZR brass fittings as Female Elbows/Tees, MTC/FTC and Engineering plastic fittings with internal sealing system like Eq. elbows, Eq. tees, reducers, Straight couplers, Clamps at one meter spacing, with PAP valves etc. Make Kitec, Maithilee and Vista. Concealed, installation including cutting chases and making good in the wall etc, Complete in all respect. 1620 (20mm OD) pipe.

Internal work:- Exposed on wall Providing and fixing of Polyethylene/Aluminum/Polyethylene (PE-AL-PE) composite Pipes as per IAPMO IGC-INDIA 308, UMC-1 TM certification marked on the pipe at the interval not greater than 1 meter with nominal pipe size with manufacturer's name or trade mark including all relevant DZR brass fittings as Female Elbows/Tees, MTC/FTC and Engineering plastic fittings with internal sealing system like Eq. elbows, Eq. tees, reducers, Straight couplers, Connectors, with PAP valves etc. Trenching, re filling and testing etc. Complete as per Engineer In Charge. Make Kitec, Maithilee and Vista.

1620 (20mm OD) pipe

2025 (25mm OD) pipe

2532 (32mm OD) pipe

SUB HEAD - III : DRAINAGE SYSTEM

Earthwork in all kinds of soil excavation by manual means in trenches for foundations, drains, pipes, cable etc. (not exceeding 1.5 in width) and for shafts, wells, cesspits and the like not exceeding 10 Sqm on plan, depth upto 1.5 Mtr including disposal of excavated earth upto 1 Mtr from cutting edge, disposed earth is to be levelled and neatly dressed.

Providing at site of works and lowering, laying and jointing HDPE pipes and required specials of outer diameters conforming to IS : 14333-1996 and bearing ISI mark in prepared trenches to required grade and level icluding cost of jointing materials, chemicals, labour required for handling and making joints etc. including hydraulic testing of pipes, refilling of trenches etc. complete note :- Water for initial testing will be made available free by MIDC if possible. For subsequent fills necessitated on account of rectifications water will be charged at the prevailing industrial water rates in respective industrial area.

110 mm dia 6 Kg/cm2

160 mm dia 6 Kg/cm2

200 mm dia 6 Kg/cm2

Construction brick measonery man hole in cement motor 1:4 (1 cement: 4 Coarse Sand) R.C.C top slab with 1:2:4 mix (1 cement: 2 Coarse Sand: 4 graded stone aggrigate 20 mm nominal size) foundation concrete aggrigate 40 mm Nominal Size, in side palstering 12mm thick with cement mortor 1:3 (1 cement:3 Coarse sand) finshed with floating coat near cement and making channels in cement concrete 1:2:4 (1 cement:2 Coarse snad:4 graded stone aggirgate 20mm nominal size) finished with floating coat of neat cement complete as per standard design. inside size 90cmx80cm and 45cm deep including cast iron cover with frame (light duty) 455x610mm internal dimensionals. total wt. of cover and frame to be not less than 38kg (wt. of cover 33kg and wt.of frame 15kg) with F.P.S bricks of class designation 75 (crush stone aggrigate)

Constructing masonry Chamber 60 x 60 x 75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement : 4 fine sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chain lid and RCC top slab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design. (With F.P.S. bricks) crushed

Providing and fixing Heavy class SS grating with Cockroach proof SS strainer of approved design including setting in floor with cement motor to match with floor finish as per direction of Engineer-Incharge. (Size 100 mm dia) (ISI Marked)

Providing and fixing heavy class SS grating plane including setting in floor with cement motor to match with floor finish as per direction of Engineer-Incharge (Size 100 mm dia) (ISI Marked)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank (Sintex, Electroplast, star, Lotous or equivalent having valid ISI license) (1000 ltr. Capacity 15 No.).

Making soak pit 2.5m diameter 3.0 M deep with 45x45cm dry brick honey comb shaft with bricks of class designation 75mm and S.W. drain pipe 100mm diameter 1.8 m long complete as per standard design with FPS bricks.

Sumit Gupta

M/s JINDAL BUILDERS

M/s Romesh Construction Co

vijay builders