REPAIR AND MAINTENANCE OF WATER SUPPLY INSTALLATION AND WATER TREATMENT SYSTEM IN TECH AREA AT AFS KANPUR.

M & L for rewinding of agitator motor of capacity 120 watts, 960 RPM ,single phase 230 V ,with and including copper winding wire of existing gauge with necessary insulation material including testing after repair and refixing of the same complete all as specifed and as directed.

M & L for rewinding of dosing motor of capacity 0.5 HP 3 phase 415V induction type, having 1390 RPM and using copper winding wire of existing gauge with necessary insulation material including testing and refixing of the same complete all as specifed and as directed.

M&L for pouring of Sodium Meta Hexa Phosphate in the well all as directed. (Note: Qty of Sodiaum Meta Hexa Phasphate as braught by the contractor shall be recored in MB and after pouring in the well, remaining qty shall be considered for qty of materials poured in well)

S&F of DOL starter single phase complete with MCB, over load relay, contractor, capacitor, ON/OFF push butten suitable for 2 HP pump set single phase with ammeter and voltmeter including fixing arrangement complet all as specified and as directed.

S&F for PVC insulated sheathed copper conductor cable of size 2.5 sqmm 3 core complete all as specified and as directed.

S&F for PVC insulated sheathed copper conductor cable of size 1.5 sqmm 3 core complete all as specified and as directed.

S&F sheet metal enclosure distibution board SPN, 2 way, 220 Volt AC 50 Hz complete all as specified and as directed.

S&F MCB SPN 6 to 32 Amp, 240 volts, C-Series, ISI Marked and conforming to IS 8828/IEC 60890-1 complete all as specified and directed.

Comprehensive maintenance of chloronome plant (Granule based dosing plant / "ENCEE CHLOR NC 400" plants) as per manufacturers reccomendation which include the following:- (i) Replacement of unserviceable wornout spare parts. (ii) Cleaning of plant room once in a week. (iii) Daily Checking of Chlorination plants /testing of complete system for serviceability of plant. (iv) Daily prepation of chlorine solution and daily testing of chlorine at consumer end with medical authority and maintained chlorine test record . (v) Routine maintenance and servicing of Agitator of by using necessary lubricant, replacement of bush/bearing, aligning the shaft , key etc all as directed. (vi) Minor repair of PVC pipe line using necessary fittings such as socket , elbow etc to make plant functional. (vii) Fortnightly Cleaning of ELECTROLISER Cell of ENCEE CHLOR NC-400 plant with dilute Hydrochloric (HCL) solution Note : (a) Any spares required for replacement shall be measured and paid under relevent item of Sch 'A' as supply only & rate of fixing is deemed to be included under this item.

(b) If any defect found in plant, contractor should rectify the defect with in 24 Hrs, if failed to rectify the decfect the contractor shall be liable to pay compensation ₹ 500/- (Rupees five hundred only) per plant per day. (c) All spares of dozing pump shall be purchased from original manufacturer as per existing make and type.

Supply only Gear motor for chloronome plants of capecity 40 GPD, 100 PSI, 0.90 Amp, 240 Volt, 50 Hz complete all as specified and as directed. Make: Decibac or equivalent as approved by GE.

Supply only Roller assembly complete all as specified and as directed.

Supply only Pump tube complete all as specified and as directed.

Supply only Injection check valve 3/8" size complete all as specified and as directed.

Supply only Weightned suction line strainer 3/8" size complete all as specified and as directed.

Supply only Agitator Shaft with impeller made poly propylene rigid 32 mm dia and 500 mm length complete all as specified and as directed.

Supply only Pump head for chloronome plant complete all as specified and as directed.

Supply only Check valve duck bill complete all as specified and as directed.

Supply only Diaphram 6.00 SI. for chlorine dosing pump complete all as specifed and as directed .

Supply only Orthodoline Solution for water testing complete all as specifed and as directed .

S&F of PVC tubing suction /discharge line 3/8" size heavy duty (as per sample) complete all as specified and as directed.

Cleaning of Pump house and all connected valve pits inside and outside and cleaning roof of PH building cutting of grass in side of boundery wall , surrounding of OHTs and complete remove the all waste materials approx area upto 500 sqm complete all as specified and directed.

Supply & filling pea gravel for packing of size 3 to 5 mm to be designed by the contractor of natural shape brought direct from river bed and packing around the casing and slotted pipe in deep borewell all as directed by Engineer in Charge. (Note:- Qty of "Pea" Gravels as brought by the contractor shall be recorded in MB as stack measurement and after filling/ pouring Pea gravel in the well, remaining qty of stack measurement shall be considered for payment purpose)

S&F discharge head assembly 150 mm dia including PCC 1:2:4 type B1 using 20 mm graded stone aggregate for and with provn of bolts of required size for foundation etc complete all as specified and directed

S&F in replacement new generation 25/26 Watt, IP-65 POST TOP, energy saving, environment friendly, long aesthetically designed with symmetrical light distribution spun aluminium landscape luminaire with high power LEDs as light source including fixing arrangement complete all as specified and as directed. Note:-Phlips Cat No. BGP200LED 26CW GR CPC SPD/ Bajaj Cat No. BGC TN 24WH/ Crompton cat No. CBP-610-25-57-SL-CA-NBG as approved by GE

Demolition of Cement concrete (Unreinforced) of any description in ground floors and pavings not exceeding 75 mm thickness (below or above ground level) complete all as specified and directed.

M&L for 75 mm thick plain cement concrete (1:3:6) type C-2 (using 40mm graded stone agg) as in flooring/plinth protection/sub-base finishing concrete surface even and smooth without using extra cement complete all as specified and directed.

Supply only of Calcium Hypo Chlorite chlorine, (Calcium based high strenght granular) decomposes clear in water solution , free of foreign matter , the chlorination chemical should contain appropriate quantities of dispersants, corossion inhibitors to prevent encrustation scaling in distribution systems, mercury and other heavy metal conteminents in chlorination all as directed by Engineer in Charge. Note: Qty brought at site shall be recored in MB

Supply and fixing Dosing tank capacity 100 liter PE / FRP Tank with PE / FRP Lid and Level Gauge complete all as specifed and as directed .

Supply only Residual chlorine testing kit range 0.2 ppm to 2.00 ppm complete all as specifed and as directed.

M&L for fixing in replacement ventuary/ orific arrangment made out of MS pipe 150 mm bore 7.0 mm thick 0.50mtr long(appx) including welding of flange at both end and five Nos. socket of 20 mm bore with fixing of nipple and gate valve of size 20 mm bore and one No. reducer of size 50 x 20 mm complete all as directed by Enginner in charge.

Supply , install, testing and commissioning of high pressure single head gear motarised adjustable dosing pump with 100 Ltr FRP tank with Lid, level gauge and agitator with shaft and blade in SS 316(FRP/Epoxy coated) MOUNTED ON TANK, suitable for adjustable presure from 0 to 100 psi, Power 230 Volt, 50Hz, 44RPM with out put of chlorine solution 2US GPD to 40US GPD complete all as specified in Govt of India manual on water supply and treatment chapter 8 all as specified & directed by Engineer in Charge. Make: Aqua /Pearl Filter /Advance-2000/Jesco as approved by GE

M & L agitator motor of capacity 120 watts, 920 RPM single phase 230 V complete all as specifed and as directed.

Reapir/Maint of LT panel of any size/type, cleaning inside/outside and around the panel, checking and tightening of all incoming and outgoing connections by replacing aluminium lugs, pieces of burnt wires of existing size as required to make it functional complete all as specified and as directed.

S&F in replacement of Power Contactor three phase 415 volt, 50 Hz, 70 A, AC3 and 100 A, AC1 type ML4 suitable for 50 HP pump/motor complete all as specified and as directed.

S&F in replacement of Power Contactor three phase 415 volt, 50 Hz, 32 A, AC3 type ML3 suitable for 30 HP pump/motor complete all as specified and as directed.

S&F in replacement of Power contactor three phase 415 volt, 50 Hz, type ML2 suitable for 20 HP pump/motor complete all as specified and as directed.

S&F in replacement of Over Load Relay range suitable for 7.5 HP to 45 HP pump set complete all as specified and as directed.

Taking out / Lifting of defective submersible pump set of 45/30 HP capacity from bore well including motor, column pipes upto 150 mm dia, steel rope, submersible cable and accessories etc and depositing in AGE E/M store yard complete all as specified and as directed.

All as per item No. 38.00 but submersible pump set of 15/12.5/7.5 HP capacity complete all as specified and as directed.

All as per item No 38.00 above but submersible pump set of 2.5/2 HP capacity complete all as specified and as directed.

Lowering only submersible pump set of 45/30 HP along with motor, column pipes, steel rope, submersible cable and accessories etc after repairing including testing commissioning of submersible pump set complete all as specified and as directed.

All as per item No. 41.00 but submersible pump set of 15 / 12.5 / 7.5 HP capacity complete all as specified and as directed.

All as per item No 41.00 above but submersible pump set of 2.5/2 HP capacity complete all as specified and as directed. Note for item No 38, 39 & 40:- All spares required to make the motor, pumps, column pipe etc serviceable shall be measured and paid separately under relevent items of BOQ as supply only including transportation to and from upto contractor workshop.

Dismantling of pump motor set 7.5 to 45 HP complete, (Taken out under above item / lying U/S in store yard of AGE E/M) cleaning all dismantled spares parts / winding for inspection of Engineer-in-Charge to ascertian the scope of work for repair / replacement of parts complete all as specified and as directed. Note :- Spare parts shall be measured and paid separately under respective item of BOQ.Measurement wrt capecity of pump motor shall be recoreded

Rewinding of submersible motor, 45 HP, 3 Phase, 50 Hz, 415 Volt with PVC insulated / coated super enameled copper winding wire of existing gauge with other winding material such as insulating paper, sleeves, bamboo stick etc. as per standard manufacturers specification including cleaning of stator, slots including replacement of defective parts and testing complete all as specified and as directed .Note: -Measurement wrt capecity of pump motor shall be recoreded

All as item No. 13.00 above but submersible motor 30 HP complete all as specified and as directed.

All as item No. 13.00 above but submersible motor 15/12.5 HP complete all as specified and as directed.

All as item No. 13.00 above but submersible motor 7.5 HP complete all as specified and as directed.

All as item No. 13.00 above but submersible motor 2.5/2 H.P complete all as specified and as directed.

S&F in replacement epoxy type cable jointing kit 25/16 Sqmm 3 core complete with all the jointing material, ferrule, insulation tape etc for 1100 Volts flat submersible copper conductor cable complete all as specified and as directed.

S&F in replacement epoxy type cable jointing kit 10/6 Sqmm 3 core complete with all the jointing material, ferrule, insulation tape etc for 1100 Volts flat submersible copper conductor cable complete all as specified and as directed.

S&F in replacement epoxy type cable jointing kit 2.5 Sqmm 3 core complete with all the jointing material, ferrule, insulation tape etc for 1100 Volts flat submersible copper conductor cable complete all as specified and as directed.

Supply only SS impellers with key and distance bushes suitable for 45/30/20/HP Pump complete all as specified and as directed.

Supply only SS impellers with key and distance bushes suitable for 15/12.5/7.5/HP Pump complete all as specified and as directed.

Supply only PVC impellers with key and distance bushes suitable for 2.5/2 HP Pump complete all as specified and as directed.

Supply only NRV suitable for 45/30/20/HP Pump complete all as specified and as directed.

Supply only NRV suitable for 15/12.5/7.5/HP Pump complete all as specified and as directed.

Supply only Bearing bush upper & lower suitable for 45/30/20/HP Pump complete all as specified and as directed.

Supply only Bearing bush upper & lower suitable for 15/12.5/7.5/HP Pump complete all as specified and as directed.

Supply only Neck ring suitable for 45/30/20/HP Pump complete all as specified and as directed.

Supply only Neck ring suitable for 15/12.5/7.5/HP Pump complete all as specified and as directed.

Supply only Distance sleeve suitable for 45/30/20/HP Pump complete all as specified and as directed.

Supply only Distance sleeve suitable for 15/12.5/7.5/HP Pump complete all as specified and as directed.

Supply only High tensile nut bolts/stud suitable for 7.5 to 45 HP complete all as specified and as directed.

Supply only GM motor bush upper and lower (set of two) for 45/30/20 HP complete all as specified and as directed.

Supply only GM motor bush upper and lower (set of two) for 15/12.5/7.5 HP complete all as specified and as directed.

Supply only Rotor bearing sleeve upper and lower for 45/30/20 HP complete all as specified and as directed.

Supply only Rotor bearing sleeve upper and lower for 15/12.5/7.5 HP complete all as specified and as directed.

Supply only Coupling with key for motor pump for 45/30/20 HP complete all as specified and as directed.

Supply only Coupling with key for motor pump for 15/12.5/7.5 HP complete all as specified and as directed.

Supply only Sand Guard for submersible pump set for 45/30/20 HP complete all as specified and as directed.

Supply only Sand Guard for submersible pump set for 15/12.5/7.5 HP complete all as specified and as directed.

Supply only Housing upper & lower for 45/30/20 HP complete all as specified and as directed.

Supply only Housing upper & lower for 15/12.5/7.5 HP complete all as specified and as directed.

Supply only Thurst bearing assembly for submersible pump set motor of 45/30/20 HP complete all as specified and as directed.

Supply only Thurst bearing assembly for submersible pump set motor of 15/12.5/7.5 HP complete all as specified and as directed.

Supply only CI Bowl suitable for submersible pump set 45/30/20 HP complete all as specified and as directed.

Supply only CI Bowl suitable for submersible pump set 15/12.5/7.5 HP complete all as specified and as directed.

Supply only flat water proof submersible cable 3 core copper conductor, PVC insulated 1100 volts grade stranded 16 Sqmm , ISI marked and connected to submersible motor complete all as specified and as directed.

Supply only Flat water proof submersible cable 3 core copper conductor, PVC insulated 1100 volts grade stranded 6 Sqmm , ISI marked and connected to submersible motor complete all as specified and as directed.

S&F in replacement M S column pipe 150 mm dia 3.00 RM long, heavy grade both ends flanged duly welded on threads with 4 Nos mild steel flat iron ribs, and provision for passing of submersible cable including nuts, bolts and packing as required complete all as specified and as directed.

All as per item no. 82 here in before but M S column pipe 100 mm dia 3.00 RM long

All as per item no. 82 here in before but M S column pipe 80 mm dia 3.00 RM long

Dismantling wrought iron or mild steel work of any description not otherwise provided for, all as specified and directed

M&L for applying two coat of synthetic enamel paint over a coat of red oxide primer including preparation of newly steel surface of any description exc. 10 cm width or girth complete all as specified and directed

Supply only steel wire rope stranded 10 mm dia for hanging of submersible pump set including clamp etc complete all as specified and as directed.

Repair/Maint of Wire less type water level indicator system (i.e. water level indicator, connecting cables, water level sensor) of any type, checking and tightening of all connections, replacing pieces of burnt wires to make it functional complete all as specified and as directed. Note:- Spare parts shall be measured and paid seperately under respective items of BOQ.

Supply only Automatic water level indicator transmitter wire less type fixed in over head reservior heavy duty complete all as specified and as directed.

Supply only Automatic water level indicator repeater wire less type complete all as specified and as directed.

Supply & fixing in replacement of Gun metal Gate valve ISI marked with Iron wheel, head screwed both ends for Galvanised Iron pipe for sizes 15mm bore all as directed by Engineer in Charge.

All as per item No 92 but size 20mm bore

All as per item No 92 but size 25mm bore

All as per item No 92 but size 40mm bore.

All as per item No 92 but size 50mm bore.

S&F in replacement sluice valves 250 mm dia class PN-1.0 , IS-14846 with flanged ends, stainless steel spindle and iron wheel including nut bolts and rubber packing complete all as directed by Engineer in Charge.

All as per item no 97 but 200mm bore

All as per item no 97 but 150mm bore

All as per item No 97 but 100mm bore

All as per item No 97 but size 80mm bore

S&F in replacement of cast iron non-return valve 200 mm dia ncluding nut ,bolt ,washer and rubber packing complete all as specified

S&F in replacement of cast iron non-return valve 150 mm dia including nut ,bolt ,washer and rubber packing complete all as specified

S&F in replacement of cast iron non-return valve 100 mm dia including nut ,bolt ,washer and rubber packing complete all as specified

Supply, fix and replacement of Bib tap 15 mm size ISI marked standard of PTMT any colour high pressure screwed for iron pipes and fixed all as directed by Engineer in Charge.

S&F in replacement of chromium plated bib tap, cast copper alloy 15 mm bore dia with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed

Supply, installation, testing and commissioning in replacement of Submersible Pump Set electric driven, ISI marked, , pump with bronze impellars, CI casing, with ss shaft, leaded bronze bearings, / bushes , complete all as per IS- 8034 with copper wound submersible motor suitable for 415 Volts , 3 phase, 50 Hz supply of suitable HP, stain less steel tubing as per IS-9283 of 2013 ( suitable for 200 mm dia borewell ) with Head 90-95 mtrs and discharge 1400-1500 LPM, 5 stage complete all as specified & directed by Engineer in Charge. Make- KSB or equivalent Note : Details of Pump shall be entered in PRB by JE incharge and old pump shall be taken on charge. Rate quoted by contractor shall deemed to be inclusive of lifiting of existing submersible pump from borewell, removal of old pump set and fixing of new one complete with cable joint water proff and relowering complete all as specified and directed by Engr-in-charge

M&L (in replacement) for making translite colour print LED panel for water supply site plan of pump house and OHT's or any other purpose including using clear acrylic sheet, blurr acrylic sheet of suitable thickness, clipon edge lit LED frame with using of high resolution LED complete with adopter and necessary fixing arrangements for making LED panel, wall mounted complete all as specified and as directed. NOTE:- (i) Water supply site plan kept at AGE E/M-II office. (ii) Letters or characters size shall be as directed by Engineer-in-charge.

M&L (in replacement) for design, manufacture, supply, installation and comissioning LED display boards of following sizes having compact design and maintenance friendly, the base of the board made of ACP(aluminium composite Panel) 3 mm thick and back side of board covered with GI sheet 24SWG, the letters and borders made of acrylic sheet 3 mm thick of colour as approved by Engineer-in-charge, LED module should as per requirement of letter space, the display language may be English/Hindi(Alpha numeric), its visibility should be suitable for day & Night (Outdoor application) and should be visible upto 25.00m (minimum), the text effect should be static, the LED suitable for power supply 230 volts/50 Hz, AC with switch ON and OFF the power supply to the display boards, the board shall be suitably braced on back side with angle iron 40mmx40mmx3mm and making good of disturbed surfaces as per original including necessary connection with 3 core copper conductor cable 1.5 sqmm from LED display boards to ceiling rose complete all as specified and as directed:-

(a) Rectangular board having max 40 letters or characters in English language letter or character size, height not exceeding 250mm and back depth max 65mm of suitable width. NOTE:- Angle iron 40mmx40mmx3mm including nuts, bolts and washers shall be measured and paid seperately under respective items of BOQ.

S&F in replacement of Electronic Timer suitable for 7.5 HP to 45 HP star delta starter complete all as specified and as directed.

S&F in replacement of MCCB FP, 415V, 100 Amp 16 KA complete all as specified and as directed.

S&F in replacement of MCCB FP, 415V, Adjustable type 125 Amp 25 KA complete all as specified and as directed.

S&F in replacement of MCCB FP, 415V, Adjustable type 160 Amp 36 KA complete all as specified and as directed.

S&F in replacement change over switch on load type front handle operated 415V with rating of bus bar 200 Amps four pole 415 Volt complete all as specified and as directed.

Repair/maint of monoblock pump set of 0.5 H P capacity single phase by means of dismantling from foundation derusting and filling of gland packing replacement of seal bearing and rewinding of moter of existing gauge with super enamelled copper wire complete all as specified and as directed.

Taking up/ down of 15 mm bore steel tubing and connections from excavated trenches and building up to tripple storey with due care including removal from site complete all as specified and directed.

All as per item No 118 but size 20 mm bore

All as per item No 118 but size 25 mm bore

All as per item No 118 but size 40 mm bore

All as per item No 118 but size 50 mm bore

M & L for GI pipe medium grade ISI marked with all necessary fittings laid in trenches / floor /wall or cealing of size 15mm bore. Note : For Sl item No 123 to 127, pipe line shall be laid in new location or in replacement of existing pipeline and credit material will be measured accordingly .Layout diagram of pipe laid shall be recorded in MB

All as per item No 123 but size 20mm bore

All as per item No 123 but size 25mm bore

All as per item No 123 but size 40mm bore.

All as per item No 123 but size 50mm bore.

Taking up/down cast iron water main 100 mm bore (including all fitting) with spigot and socket end and joints including burning out joints and recovering lead complete all as specified and directed.

All as per item No 128 but size 150 mm bore.

M&L for centrifugally cast (spun) ductile iron pressure pipes 100 mm bore for water with socket & spigot ends confirming to IS 8329/2000 in any length for classification of K-7 suitable for rubber gasket push on with cement mortar lining inside the pipe with outside zinc coating as per IS 8329/2000 complete all as specified and as directed . Note :-Cost includes fixing of Rubber gasket joint. Note : For Sl item No 130 & 131, pipe line shall be laid in new location or in replacement of existing pipeline and credit material will be measured accordingly . Layout diagram of pipe laid shall be recorded in MB

All as per item no. 130 here in before but for centrifugally cast (spun) ductile iron pressure pipes 150 mm bore for water with socket & spigot ends confirming to IS 8329/2000 in any length for classification of K-7 suitable for rubber gasket push on with cement mortar lining inside the pipe with outside zinc coating as per IS 8329/2000 complete all as specified and as directed . Note :-Cost includes fixing of Rubber gasket joint.

S&F in replacement wireless water level indicator Digital type with 7-segment LED display water level of the tanks in % with resolution of 1-2 % resolution, it receive water level data from transmitter and display in % with reset switch to put off the buzzer sound with fuse protection system on/off switch for Receiver display unit including water level data transmitter with maintenance free water level sensor complete with maximum range of signal approx 500 m at arieal distance including necessary suitable size of copper cable connection for 230 volts supply complete all as specified and as directed. Make:- Aqua Brim model Penta cool challenger digital / Sapcon / Johnson automation and control. Note:- Old unseviceable wireless water level indicator Digital type will be deposited by the contractor in E/M store yard.

Disconnecting the electric connection from starter and motor including taking out of pumping set with electric motor of capacity 5 HP from the existing position and strip opening, cutting the burnt out winding, cleaning the stator and re-winding the same with super enameled copper winding wire of same gauge using top class of insulating material and over hauling of pump including lath / machine work for making housing of bearing, metaling, welding, turning surfacing, polishing of rotor shaft, and rethreading and replacement of neck ring, bearing of required size (Make-NBC/SKF), bushes, rubber insertion sheet, nuts, bolts and washers including necessary other items for its smooth functioning and testing complete reassembling the same and re-fixing back in its original position complete all as specified and as directed.

Disconnecting the electric connection from starter and open well submersible pump set installed in SWT of ATC including taking out of pumping set with electric motor of capacity 15 HP from the SWT and strip opening, cutting the burnt out winding, cleaning the stator and re-winding the same with super enameled copper winding wire of same gauge using top class of insulating material and over hauling of pump including lath / machine work for making housing of bearing, metaling, welding, turning surfacing, polishing of rotor shaft, and rethreading and replacement of neck ring, bearing of required size (Make-NBC/SKF), bushes, rubber insertion sheet, nuts, bolts and washers including necessary other items for its smooth functioning and testing complete reassembling the same and re-fixing back in its original position complete all as specified and as directed.

All as per item No. 135 but 30 H.P complete all as specified and as directed.

Supply and fix in replacement water pressure gauge, 100 mm dial size of range 0 to 7.0 Kg/Sqcm complete all as specified and as directed.

Supply, installation, commissioning & testing (in replacement ) of LT Bus Bar Panel of size 650mm X 600 mm X300mm, made out by CPRI approved panel manufacturer 415 volts, TPN wall / floor mounted on suitable angle iron frame outdoor type cubical made out of 2 mm thick CRCA sheet weather, dust & vermin proof with rubber gasket with high class powder coating internally & externally fixing in position by provision of nut and bolts & addition / alteration required for fixing existing cables and connecting the all incoming / outgoing cables by suitable size of aluminium lugs stands nuts, bolts & washers including to accommodate properly following control switches complete all as specified and directed:- (a) Aluminium bus bar TPN 200 Amps rating made of high conductivity aluminium strip of suitable length with sleeves - 01 Set

Sampling of Non Chlorinated Water from various pump houses under AOR of AGE E/M WS Chakeri as and when directed by Engineer-in-Charge and testing the water for bacteriogogical, Physical and chemical as per IS-1622 and 3025 from any Government/NABL approved laboratories and submission of test report to Engineer-in-Charge within 10 days of direction for testing as directed by Engineer-in-Charge complete all as specified and directed . Note:- Sampling shall be done by the authorised rep of the approved laboratory from whom the testing of water is to be carried out in presence of JE/Engineer-in-Charge.Test report shall be submitted. Payment shall only be made on satisfactory test results.

M & L for construction of valve chamber 900 x 900 x 900 mm internal dimensions, 6 mm thick MS sheet cover with 2 Nos MS hinges welded to angle iron frame of 40x40x6 mm thick with lifting hook and locking arrangement complete with necessary earth work, brick work in CM (1:6), 230 mm thick, PCC bed (1:4:8) type D2 150 mm thick, cement plastering, finishing 15 mm thick in CM (1:4) and applying a coat of black bituminous paint to the steel surfaces including dismantling and removal of old unserviceble valve pit remains all as specified and directed.

M & L for construction of valve chamber 600 x 600 x 600 mm internal dimensions, 6 mm thick MS sheet cover with 2 Nos MS hinges welded to angle iron frame of 40x40x6 mm thick with lifting hook and locking arrangement complete with necessary earth work, brick work in CM (1:6), 230 mm thick, PCC bed (1:4:8) type D2 150 mm thick, cement plastering, finishing 15 mm thick in CM (1:4) and applying a coat of black bituminous paint to the steel surfaces including dismantling and removal of old unserviceble valve pit remains all as specified and directed.

M&L in replacement for laying rubber matting infront of electric panel of installation of size 1M X 2M X 3 mm thick, class 'C' ISI marked (IS-15652-2006) complete all as specified and as directed.

S&F in replacement of fully automatic star delta starter suitable for 50 HP pump set with relay 45-75 Amp in sheet metal enclosure complete all as specified and as directed.

S&F in replacement of fully automatic star delta starter in replacement suitable for 30 HP pump set with relay 30-50 Amp in sheet metal enclosure complete all as specified and as directed.

S&F in replacement 70 W LED, energy saving, environment friendly, long life exclusive innovating dia cast aluminium IP-66 protection, flood light suitable for highway lighting and general purpose including fixing arrangement and fixed on overhead tank's pillar / pump house complete all as specified and as directed. Note:-Bajaj Cat no. PRAZE F 112L WH NB-A45TG SD/ Philips Cat No. BVP281 LED 085 CWFG SY5WB 70W V1/ Crompton cat Part No. LFL-70 CDL/60-M, 70W as approved by GE

M&L for installation, testing & commissioning of 415 Volt, 3 phase 4 wire system LT feeder pillar box, cubical indoor type with front, back, top and bottom portion fabricated with 3.15 mm thick CRCA sheet and inner portion fabricated with 2 mm thick CRCA sheet and shall be folded and braced as necessary to provide a rigid support for all components of external adequate size as per drawing of panel approved by GE, complete with aluminium bus bars mounted on DMC supports and insulated with heat shrinkable PVC sleeve, interconnection control wiring with suitable size of copper conductor cable, name plate , danger plate, earth point independent compartment with hinged doors, cable glands, weather and vermin proof construction powder coating etc necessary PCC work for foundation support complete all as specified and directed with and including comprising of the following:-

INCOMING : MCCB adjustable type 4 pole 415 V, AC current rating 125 amp breaking capacity 25 KA complete all as specified and directed - 01 Nos. METERING AND INDICATIONS: (i) LED indicator lamp unit operating voltage -220/240 VAC (variation -20% to =10 % of rated voltage) in red ,yellow, blue colour complete all as specified and directed - 09 Nos (For incomer, outgoing & starter BUS BAR (i) Aluminium bus bar of size 50 mm x 10 mm for all phase conductor and neutral conductor of size 25 x 5 mm with heat shrinkable PVC sleeves and colour coded in Red, Yellow, Blue and Black to identify the three phases and neutral of the system, supported on un breakable, non hygroscopic DMC insulated supported at sufficiently closed interval - 01 set .

OUT GOING : (i) MCCB adjustable type, 4 pole,415 VAC current rating -100 Amp, breaking capacity 25 KA complete all as specified and directed -01 Nos (ii) MCCB TPN ,415 VAC, current rating -63 Amp ,10 KA complete all as specified and directed -01 Nos (iii) MCB SPN ,215 VAC, current rating -32 Amp 10 KA complete all as specified and directed -02 Nos (iv) FASD starter suitable for 41 HP submersible pump set complete with under voltage & over voltage protection system– 01 Nos (v) Electronic timer, ET 100, 9-30 sec, coil voltage-240VAC ,50 HZ -01 no. (vi) Phase sequencer and motor protection system suitable for 41 HP capacity motor for auto change of phase sequence, single phasing system low, high voltage protection complete-01 no.

M&L for earthing complete with galvanized mild steel earth plate electrodes 600x600x6mm thick buried directly in ground to a depth not less then 2.25m deep below ground level with top edge of the plate not less then 1.5 m below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around to the plate, using GI strip 32 x 6 mm as earth strip electrode bolted or rivited to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 40 mm dia GI light grade pipe from upper end of earth plate up to equipment 20 mm dia bore GI pipe light grade as water pipe from earth chamber to upper edge of earth plate, Test point, GI funnel with wire mess fixed on water pipe and PCC 1:2:4 type B1(using 20 mm graded crushed stone aggregate) as in pit chamber and RCC pit cover 50 mm thick precast RCC 1:2:4 type B1(using 20 mm graded crushed stone aggregate) duly reinforced with MS round bar 6 mm dia @ 100 c/c both way with 10 mm dia MS TMT bar as in lifting handles, excavation, earth work including laying of GI Pipe concealed in floor and wall all as described in electrical plate of SSR Part-I including testing on completion complete all as specified and as directed.

S&F in replacement LED Aviation light 7 watt of approved make with all necessary connection complete all as specified and directed.

Supply and fixing of Soft starter suitable for submersible pump set of 30/40 HP capacity, current rating 25A-100A, 240 Volt, voltage operating range of 208-600V AC, complete as all as specified and directed by Enge-in-charge.Make - ABB model No.1SFA897102R7000 or equivalent in L&T / Havells

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth and getting out for taking out/laying pipes in soft/loose soil complete all as specified and directed.

Returning, filling in and including spreading levelling watering and well ramming in layers not exceeding 25cm thick in solf/loose soil after pipes are laid complete all as specified and directed .

Removing of excavated material not exc 50 mtr distance and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

M&L for XLPE insulated, armoured heavy duty electric cable with stranded aluminium conductor, 1100 volts grade 50 sqmm 3.5 core laid in trenches/panel or passing through pipe including connecting with suitable lugs, nuts and bolts and testing complete all as specified and directed

All as per item no. 153 but cable of 25 Sqmm 3.5 core laid in trenches/panel or passing through pipe including connecting with suitable lugs, nuts and bolts and testing complete all as specified and directed

S&F in replacement 1100 volts grade cable PVC insulated 10 sqmm multistranded aluminium conductor, overall PVC sheathed twin core flat cable complete all as specified and directed.

S&F in replacement 1100 volts grade cable PVC insulated 6 sqmm multistranded aluminium conductor, overall PVC sheathed twin core flat cable complete all as specified and directed.

Please Enable Macros to View BoQ information