Upgradation of Admin infra towards conduct of AF Day fly past at AF Station Borjhar.

Amount

Demolition of brick work or stone boulder measonary, built in cement mortar including all quoins, pillars etc complete all as specified and as directed.

Demolition of concrete (un-reinforced) in ground flooors and paving not exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Earth work in excavation by mechanical means (Hydraulic excavator)/ in foundation trenches or drains (not exceeding 1.5 mtr in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 mtr, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 mtr.

M&L for PCC (1:4:8) type D2 using 40 mm graded stone aggregate as in foundations filling in mass concrete all as specified.

M&L for RCC (1:1.5:3) nominal mix (with 20 mm graded stone aggregate) as in foundation, footing & plinth beam etc complete all as specified and directed.

M & L for RCC (1:1.5:3) nominal mix (with 20 mm graded stone aggregate) as in column complete all as specified and directed.

M&L RCC (1:1.5:3) nominal mix using 20mm graded stone aggregate as in roof beam & lintel band complete all as specified and directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surface all as specified & directed by Engineer in Charge.

M&L for rough finished Formwork to sides and soffits of floor or roof beams, beam haunch ings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc

Rough finished Formwork to sides of pillars, posts, struts, columns and stanchions circular on plan

M&L for TMT steel bars 10mm dia and over to length bent to shape required, incl cranking bending spirally for hooping for columns, hooking ends and binding with MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as directed by Engineer in Charge.

All as per Serial item here in above but 8mm dia & over upto and incl 10mm dia in stirrups, spacers and binders.

Returning, filling in and including spreading, levelling, watering and well ramming in layers not exc 25 cm all as specified.

Removing of excavated soil to a distance exc 250m but not exc 500m complete all as specified and as directed by Engr-in-Charge

M&L for brick work with sub- class 'B' bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) all as specified

M&L for PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in sides filling and mass concrete, coping/ benching complete all as specified and directed by Engr-in-charge.

M & L for rendering 15mm thick on fair faces of brick or concrete wall surfaces in cement mortar 1:4 finished surfaces fair & even using WPC (Water Proofing Compound) as per manufacturers instructions complete all as specified and directed. Note : WPC measured and paid separetly.

Supply only Integral waterproofing compound complete all as specified and directed.

M&L for preparation of new plastered surface of walls/ roof/ floor and two coats of weather proof Acrylic emulsion paint (exterior grade) on wall, roof or floor incl necessary scafolding over one coat of weather primer complete all as specified and as directed by Engr- in- charge.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete, all as specified and directed .

Provision of 4mm thick ceiling tiles of size 595mm x 595mm for including aluminium anodised section of size, wall angle 30mm x 25mm x 2mm thick, main / cross tee-section 15mm x 15mm x 1.4mm and suspended with 4mm dia GI wire of suitable length and including fixed & aluminium snap grid all as per clause 10.38.1 of SSR Part-I and as per manufacturer’s instructions complete all as specified and as directed by Engineer-in-Charge.

S&F Aluminium composite sheet exterior grade 3mm thickness for paneling work of any colour including aluminium frame work section size 50mm x 37mm x 1.50mm thick with aproved solution to fix panel. Aluminium core thick not less than 0.25 mm & as directed by Engineer in charge.

M&L for colured Virified Ceramic tiles double charged 7-8mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm not exceeding1.0 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed or bedding layer in cement mortar (1:4) complete all as specified and as directed.

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft/dense soil.

Excavating in post holes (or similar holes) each not exc 0.5CuM, getting out in soft soil returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm

M&L for PCC (1:3:6) type C2 using 40 mm graded stone aggregate as in foundations filling in mass concrete all as directed by Engineer n Charge.

M & L for hard core of broken stone boulder of gauge not excceding 63 mm, deposited spread and leveled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for PCC 1:2:4 type B2 using 40 mm graded stone aggregate as in floor 150 mm thick complete all as specified

M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. and similar work confirming Fe 410 (Gde- E quality- B)

M&L for preparation for new steel untreated surfaces of any description, over 10 cm in with of girth, not otherwise described with two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified & directed.

S&F for 12mm thik transparent toughened glass with Airforce logo as per specified and directed

Material and labour for Point wiring with 1.5 Sqmm FR PVC insulated and sheathed multi stranded (FRLSH) copper conductor cable in and incl rigid PVC conduit concealed with sunk cast iron/ pressed steel terminal boxes of adequate size with suitable thickness hylum laminated sheet, cover of adequate size for one light or one fan controlled by one switch incl 1.5 Sqmm (FRLSH) PVC insulated and unsheathed multi stranded copper conductor cable as earth wire (green colour) to common earth dolly complete all as specified and directed by Engr-in-charge. Note : (a) Unit rate include for cutting chases for conduits and sinking for boxes and making good to wall, floors etc (b) On RCC roof ceiling PVC conduit shall be provided on surfaces for fan etc with proper fixing clips all as directed

All as per serial item No 34.00 here in before but for one 3 pin 5 Amp socket outlet on independent board.

Material and labour for Point wiring with 4.0 sqmm FR PVC insulated and sheathed multi stranded (FRLSH) copper conductor cable drawn in and including rigid PVC concealed conduit medium grade of suitable size with sunk cast iron/pressed steel terminal boxes of adequate size with suitable thickness plastic laminated sheet, cover for one 3 pin socket outlet 15 Amp on independent board including continuous 4.0 sqmm copper conductor cable (FRLSH) (multistranded) PVC insulated and unsheathed Cable as earth wire to common earth dolly, complete all as specified and directed by Engr-in-charge

Material and labour for ceiling rose surface bakelite two to three terminal isolated body fixed on PVC round block, 6A, Pilot 2 Plate, complete all as specified and directed by Engr-in-Charge

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

Supply and fix in repairs of DB 8 way MCB SPN double door, glazed type, IP 43 protection,Glazed door, isolated neutral bar,insulated bus bar assembly,mechanical strength of IK09, complete all as specified and directed. Make : Legrand / Indo asian / Havells or its equivalent in specified makes in CA.

Supply & fix in repair of MCBs single pole (SPN) 6 to 32 Amps with 10 KA breaking capacity of 'C' series in distribution boards confirming to IS/IEC 60898-1 (ISI marked) complete all as specified and directed.

Supply & fix in repair of MCBs single pole (SP) 6 to 32 Amps with 10 KA breaking capacity of 'C' series in distribution boards confirming to IS/IEC 60898-1 (ISI marked) complete all as specified and directed.

M&L for Type 1+2 AC Surge Protection Device 1P+N (2 Pole) 320 volt, 15KA, without Remote Signaling, complete all as specified and directed. Make : Legrand / Indo asian / Havells or its equivalent in specified makes in CA.

M&L for Earthing complete with galvanized steel earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25 Metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level, connected to galvanized earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.5 of SSR Part-I (2009) including filling of charcoal dust , common salt all around Earth plate upto 150mm, 20mm bore GI medium grade watering pipe, 15 mm bore light grade earth lead protection pipe upto main board, funnel with wiremesh, 40mm thick RCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate reinforced with suitable handle and angle iron frame and necessary excavation and earth work in any type of soil etc. complete all as specified and as directed including testing on completion. Note : The rate quoted shall inclusive of GI wire 4 mm dia with GI pipe protection 15 mm, light grade up to 7.5 m

S&F Metal flush Box 1/2 Module, complete all as specified and directed by Engr-in-charge

S&F Metal flush Box 3 Module, complete all as specified and directed by Engr-in-charge

S&F Metal flush Box 6 Module, complete all as specified and directed by Engr-in-charge

S&F Metal flush Box 12 Module, complete all as specified and directed by Engr-in-charge

S&F Modular Plate 2 module White cover plate with frame, complete all as specified and directed by Engr-in-charge

S&F Modular Plate 3 module White cover plate with frame, complete all as specified and directed by Engr-in-charge

S&F Modular Plate 6 module White cover plate with frame, complete all as specified and directed by Engr-in-charge

S&F Modular Plate 12 module White cover plate with frame, complete all as specified and directed by Engr-in-charge

M&L for Modular type 5 step Fan Regulator - 2 M oro white, complete all as specified and directed by Engr-in-charge

M&L for Modular switch 6 A One way switch white, complete all as specified and directed by Engr-in-charge

M&L for Modular 6 A, 5 pin socket, complete all as specified and directed by Engr-in-charge

M&L for Modular 6 A/16 A socket, complete all as specified and directed by Engr-in-charge

M&L for Modular 16 Amp One way switch white, complete all as specified and directed by Engr-in-charge

M&L for Dummy Plate - 1 Module Oro (White), complete all as specified and directed by Engr-in-charge

Supply and fixing ceiling fans complete with blades, down rods, with modular electronic regulator and accessories, 230V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) Supply and fix ceiling fans, complete with three blade, down rod, accessorie completeall as specified and directed by Engr-in-Charge

S&F Sheet metal enclosure having single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amp.

Supply, install, test and commission commercial type wall mounted electric chimney made out of 16 SWG stainless steel of 304 grade with front turned down, angular frame work fully welded/ brazed of hood size 10 ft X 6 ft suitable for Indian Cooking Range of 4 Burner including with the following components :- Contd......

(i) Low height stock pot of suitable size as directed by Engr-in-Charge & as required at Site with Stainless Steel Hood of size 10 ft X 6 ft (ii) Three Nos 18 Inches Heavy Duty Exhaust Fans of approved Make fixed in Stainless Steel Hood for air suction (iii) All electrical works such as point wiring with suitable size of wire, switch, socket outlet, ceiling rose, MCB DB etc of approved make deemed to be included in the item (iv) One exhaust fan fixed at end of 2 HP capacity to desipate the exhaust gas at end of duct. (v) S.S duct line of appx. 35 ft of adequate dia as to carry out exhaust gas out of kitchen Note : The entire system shall be made for suction capacity of minimum 1800 mtr3/ hour with auto clean technology & with oil collector S.S chamber

Excavating in trenches manually not exceeding 1.5m wide and not exceeding1.5 mtr in depth/ width for laying under ground cable / foundations and getting out in soft / loose soil all as specified and directed. Note : During excavation no mechanical excavator is permitted at site, contractor will do the excavation through manually.

M&L for HDPE Double wall corrugated pipe of size 63/50 mm as per IS: 16098 Part-II-2013 and ISO 21138 & BSEN 13476-1 to 3 laid in trenches/ wall for protection cables complete all as specified and directed.

S&F Double wall corrugated pipe coupler for pipe size 63/50mm all as directed by Engr-in-Charge.

S&F in repair of UG cable XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 Volts grade, cross section area incl taking down of size 16 sq mm 4core complete all as directed.

S&F HOT moulded (FRP) junction Box for street light fixed on pole with locking arrangement with IP-65 protection of size 205 x 255 x 112 mm, with busbar strip of suitable rating upto 63 Amps capacity mounting on DMC insulators (08 Nos) with nuts and bolts complete with 01 Nos MCB SP 6 Amp fixed over din rail and one bracket & nuts and bolts of suitable size to fix with pole complete all as specified and directed by Engr-in-Charge. Make : Hensel / OBO Note : (i) Each aluminium busbar having 4 to 5 holes for connection of cable with nuts and bolts etc. (ii) Rates for MCB SP 6 Amps and clamp with nuts & bolts are inclusive in the above quoted rate.

S&F LED decorative Bollad light of 10/11W, IP65, CCT(K)-3000 for new generation, Sturdy IP 65 LED Bollard with excellent light out put through its PMMA window ensuring maximum illumination aspect in surrounding. including taking down old unserviceable bollard light of any capacity. Make : Havells/ Wipro/ Philips or equivalent make specified in CA.

M & L for Energy saving,environmental friendly, long life, exclusive innovative die-casting aluminium IP66 flood light of capacity 210/ 200W,suitable for highlighting architectural facade and general purpose lighting complete having Lumen efficiency of LED >140 lm/W, System lumen efficiency> 110 lm/W and viewing angle of 120°, Operating temperature: -10 °C to +50 °C, Operating voltage range: 100 V - 300 V, LED Life L70 >50000 hrs Powered by Built-In Potted, isolated electronic LED driver (SMPS based constant current supply) with lower THD, Output Open / Short Circuit protection, Over Voltage protection, Surge Voltage Protection upto 10kV & other safety test as per IS 15885 Part-2/Sec 13 and repair/ replacement of manufacutring warranty of minimum 3 years. Make : Wipro/ Havells/ Bajaj/ Surya or equivalent make specified in CA.

KUNDAN ENGINEERS AND BUILDERS (BID ID -3433713)

M/s Beekey Seekey Traders (BID ID -3432987)

Ms Jahnabi Construction (BID ID -3433743)

M/s Vishnu Enterprises (BID ID -3433842)

M/S B.H. ENTERPRISE (BID ID -3433400)

Purbanchal Construction Co (BID ID -3431964)

M/s A R Traders (BID ID -3433699)

M/s Kajal Das (BID ID -3433167)

M/s Dhruv Enterprises (BID ID -3432610)

M/s DC Traders (BID ID -3433188)