PROVISION OF GUARD POST ALONGWITH GUARD ROOM AT CQA(V) AND ADDN/ALTN OF TOILET / BATHROOM OF GADRA BLOCK P-286 AT MAC GP, MIC and S UNDER GE(S) AHILYANAGAR

Amount

M&L for Surface excavation n. exc 30 Cm deep and averaging 15 cm deep and getting out in Soft/loose soil.

Removal excavated soil exc 250m but not exc 500m and depositng where directed at a level not exc 1.5m above the starting point complete all as specified and as directed.

Earth work in excavation in all kind of soil by mechanical means (Hydraulic excavator) in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m in depth, including getting out the excavated soil and disposal of surplus excavated soil, within a lead of 50 m all as specified and as directed

Earth work in excavation in all kind of soil by mechanical means (Hydraulic excavator) in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift exceeding 1.5 m but not exc 3m in depth , including getting out the excavated soil and disposal of surplus excavated soil, within a lead of 50 m all as specified and as directed

Excavation by mechanical means in any kind of soil (hydraulic excavator) over areas (exc 30 cm in depth, 1.5 m in width and exc 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5m, complete all as specified and as directed.

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation and mass concrete complete all as specified and as directed.

M&L for moorum filling in floors or paving, laid in layers not exc 15cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L for hardcore of gauge not exc 63 mm size of broken stone or boulder, deposited, spread and levelled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for 100mm thick plain cement concrete, 1:4:8 type D2, using 40 mm graded stone aggregate as in sub base complete all as specified and as directed.

M & L for anti termite treatment for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and as directed.

M & L for anti termite treatment for Treating the the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed.

M & L anti termite treatment for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and as directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surfaces of concrete complete all as specified and as directed.

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions squre, rectangular or polygonal for rough finished surfaces of concrete complete all as specified and as directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams,etc for rough finished surfaces of concrete complete all as specified and as directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exc 200mm thick (Horizontal or sloping) for rough finished surfaces of concrete complete all as specified and as directed.

M&L for reinforced cement concrete, M-25 Design mix (20mm graded stone aggregate) as in foundations including rafts, footings, foundation beams; plinth beams; bases for columns, etc complete all as speified.

M&L for reinforced cement concrete, M-25 design mix (20mm graded stone aggregate) as in columns, pillars, piers, posts and struts complete all as specified and as directed

M&L for reinforced cement concrete, M-25 Design mix (20mm graded stone aggregate) as in beams, cantilevers, bressummer lintel over 1.5m span complete all as specified and as directed

M&L for reinforced cement concrete, M-25 Design mix (20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified as directed.

M&L for mild steel TMT bars 5 mm dia and over upto and including 10mm dia, in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic joint filling at every 3m length and at corners complete all as specified and as directed.

M&L for brick work with old size fly ash ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified.

M&L for brick work with old size fly ash bricks, as in half brick thick walls straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and as directed.

Demolition of Brickwork/ block or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and directed.

Taking down cement or cement lime plaster on brick wall, ceiling incl. raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces, finished surfaces even & smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar 1:4 on other than fair faces of brick work or concrete surfaces (external wall) in two layers, first layer 10mm thick and second layer 5mm thick mixed with WPC as per manufacturer's instructions finished even & fair complete all as specified and as directed. Note : WPC shall be measured and paid separately.

Supply only integral water proofing compound complete all as specified.

M&L for rendering 5mm thick on ceiling surfaces in cement mortar 1:3 on fair faces of concrete surfaces including finishing even & smooth without using extra cement all as specified and as directed.

M&L for water proofing treatment to RCC roof slab, including parapet comprising with the following courses of treatment/specification from bottom to top:- (i) Surface roughening concrete slab by picking, sweeping clean and washing down with water to remove dust etc and applying cement slurry @3kg/Sqm. (ii) 15 mm thick Screed bed or bedding layer in cement mortar 1:4 as in roof slab with mixing of WPC (3% of cement content) and surface finished even and smooth without using extra cement. (iii) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.30 ltr /Sqm conforming to IS:3384-1986. (iv) APP based polymeric membrane 3mm thick (minimum), weighing 3.5 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 150 gms/Sqm) shall be laid/ applied over bituminous primer as specified above. The application of polymeric membrance shall by torch application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction. (v) Applying one coat of bituminous aluminum paint over the APP modified membrance @ 0.11Kg/sqm. Note: WPC shall be measured and paid for under separate item.

M&L for preparation of new plastered surfaces of walls and applying 2mm thick wall care putty and sanding the surface to achieve smooth surface and applying two coats of oil bound distemper of approved shade/tint over a coat of primer complete all as specified and as directed.

Material & Labour for preparation of surfaces and applying Two or more coats of 100% Premium exterior acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed.

M&L for preparation of new plastered ceiling surfaces and applying three coats of white wash complete all as specified and as directed .

M&L for preparation of new plastered wall surfaces and applying three coats of white wash complete all as specified and as directed .

M&L for 15mm bore GI tubing, medium grade laid in trenches / floors or fixed to wall in any length with screwed and socket joints together with all galvanised GI fitting such as sockets, bends, elbows, tees, reducers, unions, jointing materials etc complete all as specified and as directed.

M&L for 20mm bore GI tubing, medium grade laid in trenches / floors or fixed to wall in any length with screwed and socket joints together with all galvanised GI fitting such as sockets, bends, elbows, tees, reducers, unions, jointing materials etc complete all as specified and as directed.

M&L for 25mm bore GI tubing, medium grade laid in trenches / floors or fixed to wall in any length with screwed and socket joints together with all galvanised GI fitting such as sockets, bends, elbows, tees, reducers, unions, jointing materials etc and pressure testing, washing out complete all as specified and as directed.

S&F Fe 410-W (Gde E -250) quality 'A' as in rafters, purlins, posts, ladders, staging, plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases, Splices, angle brackets, cleats and other connections complete all as specified and directed by Engr-in-Charge.

M&L 18 to 20mm thick pre-polished granite stone slab as in table top,WHB platform, kitchen slab/platform, steps, gate pillars, cills etc or on vertical surfaces including vertical projection, including full round moulding the edge, laid over and including screed bed 15mm thick in cement mortar 1:4, jointing , pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite and rubbing polish to achieve mirror finish complete all as specified and as directed. Note : colour and shade of granite is approved by Engr-in-Charge.

M&L for machine cut cudappah stone slab 20-25mm thick as in cooking platform etc including cutting chases in brick wall and fixing the slab in cement mortar including rubbing and polishing complete all as specified and as directed.

Dismantling of stone slabs and interlocking tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortor complete all as specified and as directed.

S&F prepainted galvalume aluminium zinc coated galvanised iron based corrugated steel sheets 0.5 mm thick of any colour having tensile strength 550 MPA as in roof covering or ridges with side lap and end laps, hips and straight flashing fixed with self taping screws (length & girth as fixed) complete all as specified and as directed. Note:- Colour & Pattern to be approved by Engineer-in-Charge.

S&F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top), 1000 litres capacity, tripple layered, hoisted and fixed in position including 20 mm dia float valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting all as specified and as directed.

M&L for 20mm gun metal or bronze globe / gate valve, ISI marked, screwed both ends suitable for GI tubing with side way operating GI lever handle complete all as specified and as directed.

M&L for 20 to 22 mm thick machine cut kota stone flooring (size of kota stone slab 22"x22") laid over and including 20 mm thick bedding layer of cement mortar 1:6 jointed with grey cement slurry mixed with pigments to match the shade of slab including cutting, rubbing and mirror polishing complete all as specified and as directed.

All as per serial item No. 47 but 18 to 20 mm thick kota stone on vertical surfaces such as in skiting /dado of size as required at site over and including 10 mm thick backing coat of cement mortar 1:3.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per specifications & drawing complete all as specified and as directed by Engineer-in-Charge

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately

S&F butt hinges,Stainless steel, 100mm long fixed by welding to existing MS pressed steel chowkhat/shutter or fixed to wooden/WPC frame with necessary SS screws complete all as specified and as directed.

S&F 150mm size aluminium anodised handle, extruded section complete all as specified and as directed.

S&F 150 mm size aluminium anodised, barrel tower bolts of extruded section and fixed all as specified and as directed.

S&F 300 mm long aluminum alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of steel, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy complete all as specified and as directed.

S&F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed.

S&F mild steel framed work such as grill, gratings, guard bars, iron doors, railings, frame work for water tanks, ladders etc with ends of bars shouldered and/or riveted or forged into spikes and similar works including one shop coat of zinc chrome primer and cutting holes/making surface good in cement concrete 1:2:4 type B-0 complete all as specified.

S&F powder coated aluminum windows, three track, made out of aluminium sections (make Jindal or equivalent) including all necessary fittings, 5mm thick sheet glass, rubber/ neoprene beading, locking arrangements all as specified and as directed and comprises of following sections :- (a) Window frame (i) Bottom-Section 20671 (Wt not less than 0.699 Kg/m) (ii) Top & Size - 20672 (Wt not less than 0.594 Kg/m) (b) Shutter (i) Vertical (end)- 20669 (Wt not less than 0.548 Kg/m) (ii) Vertical (lock) - 20689 (Wt not less than 0.481 Kg/m) (iii) Bottom - 20718 (Wt not less than 0.263 Kg/m) (iv) Top - 20668 (Wt not less than 0.377 Kg/m) Note:- Colour to be decided by Engineer-in-Charge.

S&F powder coated anodised aluminium louvered ventilator of size 50/55cm wide and 85/90 cm height with minimum 07 louvers, made up of aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, screws etc complete all as specified and as directed. Note : Colour shall be as approved by GE/Engineer-in-Charge.

M&L for 7-8mm thick non skid coloured ceramic tiles (square or rectingular) area of each tile exc 0.06 sqm but not exc 0.11 sqm in floors etc, colour/shade as approved by GE, set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles over & including 15mm thick screed bed in cement mortar 1:6 complete all as specified & as directed.

M&L for glazed coloured ceramic tiles of size 450x300x7mm thick in vertical surfaces, colour/shade as approved by GE, set and jointed in neat cement paste and pointed in white or coloured cement to match with the tiles over & including 10mm thick rendering in cement mortar 1:4 complete all as specified & as directed.

M&L for 7-8mm thick non skid coloured ceramic tiles (Premium/ Special quality) (square or rectingular) area of each tile exc 0.06 sqm but not exc 0.11 sqm in floors etc, colour/shade as approved by GE, set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles over & including 15mm thick screed bed in cement mortar 1:6 complete including dismantling floor, hearth or wall tilling including cement mortar bedding, and removing rubbish off the premises all as specified & as directed.

M&L for glazed coloured ceramic tiles of size 350x250x7mm/ 450x350x7mm thick (Premium/ Special quality) in vertical surfaces, colour/shade as approved by GE, set and jointed in neat cement paste and pointed in white or coloured cement to match with the tiles over & including 10mm thick rendering in cement mortar 1:4 complete including dismantling floor, hearth or wall tilling including cement mortar bedding, and removing rubbish off the premises all as specified & as directed.

S&F 35 mm thick, second class hard wood glazed and skeleton shutters, factory made, open rebated and prepared to receive glass, gauze, etc., divided in to squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamferesd or rounded, fitted with cut and mitred beads for securing glass etc., for windows and ventilators, etc are provided with stiles and rails as specified in SSR Pt I Section 8, clause 8.24 (a) complete all as specified and as directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aparture 1.40 mm, fixed with stainless steel wire staples to steel / wooden frame complete all as specified and as directed.

S&F 35mm thick, second class hard wood, plain framed, factory made, panelled shutter (two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and as directed.

S&F pressed steel doors frames of size 105mm x 60mm x 1.25mm thick, with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete as specified and as directed.

S&F 3mm thick frosted/figured glass, pin headed type and glazing with oil putty in square not exc 0.5 Sqm in each pane and fixed to steel windows including glazing pins etc. complete all as specified and as directed.

M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer complete all as specified and as directed.

M&L for preparation of new wood or wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

S&F in repairs, bib tap 15mm dia, with wall flange and aerator screwed down for iron pipe or for brass ferrule complete all as specified and as directed. Make : Cat No. F1015151 of CERA or equivalent model of makes specified.

S&F in repair 15mm bore dia angle cock with wall flange, high pressure screwed for iron pipe complete all as specified and directed. Make : Cat No. F1015201 of CERA or equivalent model of makes specified.

S&F in repair 15mm bore dia concealed stop cock with adjustable wall flange high pressure screwed for iron pipe complete all as specified and directed. Make : Cat No. F1015361 of CERA or equivalent model of makes specified.

Cutting chases n. exc 10 cm in girth, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing etc complete all as specified and as directed

S&F in repairs, 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve and handle including brackets complete all as specified and as directed. Make :- Cat No. B1010112 of CERA or equivalent model of makes specified.

M&L for PVC (SWR) floor trap with dia of outlet 75mm, plain with grating including jointing with solvent cement to waste pipe fixed in cement concrete type (1:2:4) type B1 using 20mm graded stone aggregate all as specified and as directed.

S&F in repairs,Health faucet (ABS Body) suitable for 15 mm dia pipe with 1 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. Make : Cat No. F8030111AB of CERA or equivalent model of makes specified.

S&F in repair over head shower rose 125mm size with 200mm long shower arm and wall flange all as specified & directed by Engr-in-charge. Make : Cat No. F7020111AB of CERA or equivalent model of makes specified.

S&F vitreous china wash down water closet (Pedestal pattern) EWC including connection to drain (or outgoing pipe) with and including 10 ltr capacity PVC valveless syphonic action type, flushing cistren low level, white or coloured, with inlet, ball valve, float and handle including brackets, including PVC connections 15 mm dia with PTMT nuts of length 450mm trap set and including white or black seat cover for pedestal pan with mild steel chromium plated aluminium hinging device, fixed to pan with suitable screws etc complete all as specified and as directed. Make : Cat No. S1053102 of CERA or equivalent model of makes specified.

S&F vitreous china wash hand basin, white flat back of size 550 mm x 400 mm including brackets with and including pillar tap, 15 mm bore chromium plated, fancy type, cast copper alloy with capstan head, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts and PVC waste pipe15mm dia, PVC connection pipe 450mm long complete all as specified and as directed. Make : Cat No. S2040141 of CERA or equivalent model of makes specified.

M&L for vitreous China bowl urinal flat back of size 420 x 310 x 325 mm (minimum), white with grating and union for discharge pipe (excluding flushing cistern, flush pipe) with and including urinal spreader of brass CP fixing with 15 mm dia pipe including PVC connection 15mm bore and 450mm long, 40mm PVC waste pipe & 40 mm waste coupling providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plug, with and including 60mm long screws, pointing around urinal back in cement, fixing flush pipe, complete all as specified and as directed. Make : Cat No. S4020104 of CERA or equivalent model of makes specified.

S&F 110 mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to wall all as specified and as directed.

S&F 110 mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints laid in trenches or in floors all as specified and as directed.

S&F PVC (SWR) pipes 75 mm dia single socketed in any length with rubber ring joints fixed to walls complete including clamps for securing pipe complete all as specified and as directed.

S&F 75 mm dia PVC (SWR) bends of any radius, complete all as specified and as directed

S&F 110 mm dia PVC (SWR) bends of any radius, complete all as specified and as directed

S&F PVC (SWR) 110 mm bore vent cowl all as specified and as directed

Excavation in trenches not exc 1.5m wide and not exc 1.5 m deep & getting out in any type of soil for foundations, pipes etc complete all as specified and as directed.

Returning filling in including spreading, levelling, watering and well ramming in layers in any type of soil not exc 25cm complete all as specified and as directed.

Removal of excavated soil not exc 50m and depositng where directed at a level not exc 1.5m above the starting point complete all as specified and as directed.

M&L for 40mm GI tubing, medium grade laid in trenches / floors or fixed to wall in any length with screwed and socket joints together with all galvanised GI fitting such as sockets, bends, elbows, tees, reducers, unions, jointing materials etc and pressure testing, washing out complete all as specified and directed.

M&L for cutting/ drilling existing 80mm dia. CI/ GI pipe line & taking branch connection complete including all necessary GI fittings, jointing materials, excavation and earth work etc complete all as specified and as directed.

M&L for precast cement concrete interlocking tiles 60mm thick factory made, hydraulically pressed cemented tiles of grey cement with pigments, chamfered edge, with glossy finish of M-35 grade conforming to IS-15658-2006 of approved colour, design, pattern, size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 25mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed Note : Size, shape & pattern of tiles shall be as approved by GE.

M&L providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required, including excavation, returning filling and removal of soil etc complete all as specified and as directed.

M&L for precast reinforced cement concrete, 1:2:4, type B-1, using 20mm graded stone aggregate as in cover slab of manhole, soak well & septic tank covers including necessary forms and moulds complete all as specified and as directed.

M&L for RCC hume pipes, 150 mm bore dia, class NP2, laid in trenches and jointed with collars in cement mortar 1:1 complete all as specified and as directed. Note:- (a) Excavation, earthwork and PCC bed concrete shall be measured and paid for seperately under respective item.

M&L for PCC 1:4:8, type D-2, using 40 mm graded stone aggregates as in concrete bed for 150 mm bore dia drain pipes, any type, including packing under and haunching against the sides of the pipes after they are laid & tested complete all as specified and as directed.

M&L for construction of soakage well (1.8 m dia x 6 m effective depth) including excavation in any type of strata (soil or any type of rock), foundation in PCC 1:3:6, walls of honey combed masonry including intercepting chamber and screen chamber made of brick masonry in cement mortar 1:4, SFRC cover, interconnecting pipes of RCC, complete filled with brick bats of required size complete all as per Drawing No CEPZ/2019/TD/03 complete all as specified and as directed

Construction of new septic tank for 50 users incl excavation earth work any type of soil /Rock complete all as shown on TD DRG. No. CEPZ/88/TD/17M

M&L for PCC 1:3:6, type C2 using 40mm graded stone aggregates as in surface channels and drains complete all as specified and as directed

Extra for forming fair finished drain or channel, 30cm inner girth in cement concrete, including forms, moulds, mitred/stopped ends etc complete all asspecified and as directed

M&L for cement concrete 1:3:6, type C-1, using 20mm graded stone aggregate as in copings, haunchings and the like including necessary formwork, weathering, slightly rounded or chamfered angles and throating, as directed complete all as spcified and as directed.

M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint over one coat of primer all as specified and as directed.

M&L for preparation of old decorated surfaces of ceiling and applying two coats of white wash complete all as specified and as directed .

M&L for Complete removal of existing treatment on old decorated plastered sufaces of walls by steel wire brushes, scrapping down smoke spot mould & efflorescent salt & greasy spots etc. including brooming down and washing with water and applying two coats of cement base paint over one coat of primer complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls and applying two coats of white wash complete all as specified and as directed .

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exc 1.50 sqm but n exc 4 sqm each and making good disturbed surface of walls in cement mortar (1:3) complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area not exc 1.50 sqm each and making good disturbed surface of walls in cement mortar (1:3) complete all as specified and as directed.

S&F mild steel windows with side hung double shutters (one glazed and one for wire mesh) including projecting type hinges with steel handles and steel peg stay complete with glazing bars dovetailed or welded complete all as specified and as directed.

M&L for preparation of old painted steel or iron surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

S&F galvanised mild steel wire cloth 0.36mm nominal dia of wire and average width of aparture 1.40 mm, fixed to steel doors and windows with necessary 12mm iron flats with welding and including dismantling of old wire cloth complete all as specified and as directed. Note : Rate quoted is deemed to be inclusive of iron flats as required and welding.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/ metal frames including punching or drilling out pins/spring clips complete all as specified and as directed

S&F 3 mm thick plain sheet glass and glazing with oil putty in square not exc 0.5 Sqm in each pane and fixed to steel windows including glazing pins etc. complete all as specified and as directed.

Taking up or down 15 mm bore dia GI steel tubing and connections complete all as specified and as directed.

Taking up or down 20 mm bore dia GI steel tubing and connections complete all as specified and as directed.

Taking up or down 25 mm bore dia GI steel tubing and connections complete all as specified and as directed.

Supply and fix 20mm dia CPVC pipes, SDR 11 and plain CPVC SDR 11 fittings fixed to walls/ceiling or laid in floors with and including all fittings and jointing material / solvent complete all as specified and as directed.

Supply and fix 16mm dia CPVC pipes, SDR 11 and plain CPVC SDR 11 fittings fixed to walls/ceiling or laid in floors with and including all fittings and jointing material / solvent complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top), 2000 litres capacity, tripple layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting including dismantling existing water tank all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut to facilitate demolition) complete all as specified and as directed.

M&L for 75mm thick plain cement concrete, 1:4:8 type D2, using 40 mm graded stone aggregate as in sub base complete all as specified and as directed.

M&L for reinforced cement concrete, 1:2:4 type B1 (using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

S&F in repairs, PVC connections 15 mm dia of length 450 mm with PTMT nuts complete all as specified and as directed.

M&L for water proofing treatment to RCC roof slab, including parapet comprising with the following courses of treatment/specification from bottom to top:- (i) Taking down the existing old roof treatment and roughening the surface of concrete slab by picking, sweeping clean and washing down with water to remove dust etc and applying cement slurry @3kg/Sqm. (ii) 15 mm thick Screed bed or bedding layer in cement mortar 1:4 as in roof slab with mixing of WPC (3% of cement content) and surface finished even and smooth without using extra cement. (iii) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.30 ltr /Sqm conforming to IS:3384-1986. (iv) APP based polymeric membrane 3mm thick (minimum), weighing 3.5 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 150 gms/Sqm) shall be laid/ applied over bituminous primer as specified above. The application of polymeric membrance shall by torch application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction. (v) Applying one coat of bituminous aluminum paint over the APP modified membrance @ 0.11Kg/sqm. Note: WPC shall be measured and paid for under separate item.

M & L for Water proofing treatment to floor & vertical surfaces of sunken portion complete comprising the following (floor area of WC/Bath not exceeding 1.5 sqm) :- (a) After demolition of floor and lime concrete etc. remove all loose particles along with existing water proofing treatment (any no. of layers) with wire brushes and cleaning the surfaces with water. (b) Brushing cement slurry with 1.2 kg of cement per square meter duly blended with & including water proofing compound. (c) 15mm thick (Average thickness) plaster in cement mortar (1:4) mixed with WP compound on sunken surface including walls. The corner of sunken portion shall be rounded in concave shape and adequate slope shall be made during plastering to accommodate sump pipe and curing the sunken portion with water minimum for 48 Hrs by ponding. (d) Applying self adhesive type APP based polymeric membrane minimum weighing not less than 3.5 kg/sqm and minimum 3 mm thick reinforced with polyster non-woven fabric (weight not less than 150 gm/sqm (e) M&L for PCC 1:7:12 for filling of sunken portion after concealing all membrane and sealing all joints to the entire with broken bats and light weight, floor area of WC/Bath not exceeding 1.5 sqm and provide hole in the wall and fix 600 mm long 20 mm dia GI spouts light grade, PCC 1:3:6, type C1 (using 20 mm graded stone aggregates) filling complete all as satisfaction of Engineer-in-Charge. Note- The rates include for drilling of the hole RCC @ 1.00 m centre to centre, to a depth to a length of 30 mm and fixing of PVC pipes of dia 15/20 mm laid dry and grouting with cement slurry mixed with can bax 100 chemical with pressure grouting with minimm 3 Kg/Sqm complete all as specified and directed.

S&F in repairs vitreous china counter sunk wash hand basin, oval shape (approx 520mm x450mmx 200mm size) including brackets, 32 mm dia waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts and PVC waste pipe,15mm dia PVC connection pipe complete all as specified and as directed. Make :- Cat No. 52030101 of CERA or equivalent model of makes specified.

S&F in repairs vitreous China, white, squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest, set in cement concrete type E2 1:5:10 (using 40mm graded stone aggregate) including flush pipe and connecting to trap with and excluding flushing cistren low level, white or coloured, with inlet, ball valve, float and handle including brackets, including PVC connections 15mm dia with PTMT nuts of length 450mm and making good to floor complete all as specified and as directed.

S&F in repairs vitreous china wash down water closet (Pedestal pattern) EWC including connection to drain (or outgoing pipe) excluding flushing cistren low level, white or coloured, with inlet, ball valve, float and handle including brackets, including PVC connections 15 mm dia with PTMT nuts of length 450mm trap set and including white or black seat cover for pedestal pan with mild steel chromium plated aluminium hinging device, fixed to pan with suitable screws etc complete all as specified and as directed. Make : Cat No. S1053102 of CERA or equivalent model of makes specified.

S&F in repairs 110 mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to wall all as specified and as directed.

S&F in repairs 110 mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints laid in trenches or in floors all as specified and as directed.

Supply for Pipe Supporting Clamping for Single pipe of PVC dia 110 mm (4") down take pipe fixing done with Clamping System consists of Rain Water Bracket Set with Pipe Support Channel + U Bolt Rubber Sleeve mounted System running vertically with wall distance 75 mm (3"): Pipe Support Clamping made of : 1. Rain Water Bracket Set with pipe support channel for 110 mm pipe having Wall Distance 75 mm (3") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs. 2. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Rain Water Bracket Set with pipe support channel for 110 mm pipe; Wall distance 75 mm (3") - 1 Nos. ; 2. U bolt Rubber Sleeve mounted for 4" (110 mm) PVC Pipe Dia. - 1 No.; and 3. Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2") - 2 nos. Fixing Details:Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Pune Zone Technical Drawing (TD) of Factory Made Pipe Supporting System : CEPZ/2023/TD/03 and CEPZ/2024/01. Make: Shaivi or equivalent as approved by GE.

S&F in repairs 75 mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to wall all as specified and as directed.

S&F in repairs 75 mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints laid in trenches or in floors all as specified and as directed.

Supply for Pipe Supporting Clamping for Single pipe of PVC dia 75 mm (3") down take pipe fixing done with Clamping System consists of Rain Water Bracket Set with Pipe Support Channel + U Bolt Rubber Sleeve mounted System running vertically with wall distance 75 mm (3"): Pipe Support Clamping made of: 1. Rain Water Bracket Set with pipe support channel for 75 mm (3") Pipe Dia. having Wall Distance 75 mm (3") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs. 2. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Rain Water Bracket Set with pipe support channel for 75 mm PVC pipe; Wall distance 75 mm (3") - 1 Nos. ; 2. U bolt Rubber Sleeve mounted for 75 mm (3") Pipe Dia. - 1 No.; and 3. Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2") - 1 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Pune Zone Technical Drawing (TD) of Factory Made Pipe Supporting System : CEPZ/2023/TD/03 and CEPZ/2024/01. Make: Shaivi or equivalent as approved by GE.

S&F in repairs 110 mm dia PVC (SWR) bends of any radius complete all as specified and as directed

S&F in repairs 75 mm dia PVC (SWR) bends of any radius complete all as specified and as directed

S&F in repairs 110 mm dia PVC (SWR) bends of any radius with access door complete all as specified and as directed

S&F in repairs 75 mm dia PVC (SWR) bends of any radius with access door complete all as specified and as directed

S&F in repairs, 110 mm dia PVC (SWR) branch piece, (single Y) equal or unequal of any radius complete all as specified and as directed

S&F in repair, 100mm dia, cast iron nahani trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate all as specified and directed.

S & F in repairs PVC (SWR) multi floor trap with dia of outlet 75mm, plain with grating including jointing with solvent cement to waste pipe fixed in cement concrete type (1:2:4) type B1 using 20mm graded stone aggregate all as specified and as directed.

S&F in repairs, pillar tap 15mm dia, with wall flange and aerator screwed down for iron pipe or for brass ferrule complete all as specified and as directed. Make : Cat No. F2014101 of CERA or equivalent model of makes specified.

S&F in repairs wall mixer for mixing hot and cold water and bend for connecting to shower,15 mm bore screwed for iron pipe and fixed complete all as specified and as directed. Make : Cat No. F1015401 of CERA or equivalent model of makes specified.

S&F in repairs towel rail 60 cm long between flanges all as specified and as directed. Make : Cat No. F5015103CH of CERA or equivalent model of makes specified.

S&F in repairs SS Grating with square frame (Grating thk- 1mm & frame thk- 1.5mm) of size 125mm (minimum) with waste hole complete all as specified and directed. Note: Design of grating to be approved by Engineer-in-Charge.

S&F in repairs towel ring all as specified and as directed. Make : Cat No. F5015105CH of CERA or equivalent model of makes specified.

Cleaning of sludge from SGSW/ RCC pipe line upto 150 mm dia including from intermediate manholes portion in foul conditions by mechanically operated machine means for removing blockage, taking out blocked sludge / debris etc collected in the manholes from pipe lines, cleaning & depositing the sludge/debries burried under ground, spreading necessary insecticide where sludge is deposited and covering the same with soil all as specified and as directed. Notes : (a). All sludge/debries shall be deposited in nearest pit & covered with soil and necessary disinfection shall be carried out. (b). Rs 200.00 for each complaint shall be deducted from the payment of contractor in case complaint is not attended and rectified within 24 hours since ordered. (c) Necessary tools and plants required for removing blockage shall be arranged by the contractor and cost of the same shall deemed to be included in the unit rate quoted.

All as per serial item No. 149 here-in-before but 200 mm to 300 mm bore pipes.

Demolition and breaking up of drain pipes (salt glazed ware or AC or reinforced cement concrete), set in cement mortar, dia of pipe150mm complete all as specified and as directed.

Demolition and breaking up of drain pipes (salt glazed ware or AC or reinforced cement concrete), set in cement mortar, dia of pipe 200mm complete all as specified and as directed.

M&L for RCC hume pipes, 200 mm bore dia, class NP2, laid in trenches and jointed with collars in cement mortar 1:1 complete all as specified and as directed. Note:- (a) Before starting the work the site shall be shown to the Engineer - in - charge for approval. (b) Excavation, earthwork and PCC bed concrete shall be measured and paid for seperately under respective item.

M&L for PCC 1:4:8 type D-2, using 40 mm graded stone aggregate as in concrete bed to 200 mm internal dia drain pipes, any type, including packing under and haunching against the sides of the pipes after they are laid & tested complete all as specified and directed.

M&L for precast cement concrete block masonry with PCC 1:5:8 (using 20 mm graded aggregate) solid blocks exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and as directed.

M&L for cutting into existing manhole for connecting new drains, making good to pipes & rendering, cutting out existing benching & forming branch channel 1, ½ round or ¾ section in PCC 1:2:4 type B1, smooth finished for 150 mm bore pipe complete all as specified and as directed.

M & L for point wiring complete on surface of wall (open) type with two runs of 1.5 sqmm for phase and neutral, single core, multistranded copper conductor cable of 1100 Volts grade,conforming to IS-694 1990, PVC insulated and unsheathed , FRLS cable drawn through and including PVC casing and caping (ISI marked) and its accessories such as Tee, elbow, jointer, elbow corner etc. fixed on surface of walls, coloumns/ beams alongwith 1.5 Sqmm copper conductor cable (multistranded) PVC insulated and unsheathed FRLS cable as earth wire connected to common earth dolly at one end and metalic bodies of luminaire/ fan at other end including PVC boards for mounting switches, sockets, fan Regulators, accessories etc as specified and directed for one light point or one fan point controlled by one, one way switch. NOTE: 1.Proper colour coding shall be adopted for wiring (for phase-RED,YELLOW,BLUE for Earth-Green and Neutral-Black) 2.wiring shall be done as per complaints received from user only on reqired basis it is not necessary to do whole wiring of any whole bldg. 3. All points shall be earthed up to fixtures i.e holders,tube lights,all lights,ceiling lights,bulkhead lights,bldg security lights etc.

All as per serial item No. 157 above but for one 6 Amp 5 pin socket outlet point on same board with other switches including earth wire as specified and as directed.

All as per serial item No. 157 above but for one 6 Amp 5 pin socket outlet point on independent board with other switches including earth wire as specified and as directed.

All as per serial item No. 157 herein before but with 2.5 Sqmm, PVC copper stranded cable FRLS type for phase,Neutral and earth for one 16 Amp, 6 pin socket on independent board.

M&L for switch piano flush button 6 Amp single pole one way 230 volts white finish all as specified & as directed.

S&F switch socket combination, flush type, 3 pin, 6 Amp, multipurpose, 230 volts, single pole, one way, suitable for 3 pin/2 pin 6 Amp plug top white/ivory finish all as specified & as directed.

S&F switch socket combination, multipurpose, flush type, 2 in 1 type (6 pin ) 6/16 Amps, 230V, AC all as specified & as directed.

S&F lamp holder, angle/ batten type, PVC/Polycarbonate type with back plate, suitable for batten fittings all as specified & as directed.

S&F fan regulator, step type, electronic on existing phenolic laminated sheet, 5 step, socket type, 230 volts, suitable for ceiling fan 1200/1400mm sweep all as specified & as directed.

S&F ceiling rose surface type, PVC, 50mm dia, 3 terminals including PVC mounting block white/ivory finish all as specified & as directed.

S&F sheet metal enclosure (Factory made), double door shutter type for distribution board (when MCBs are to be used), single pole and neutral, 240 volts, 4 way, protection class IP-42, suitable for fixing MCBs, Isolators etc, confirming as per IEC 61439-3, suitable for flush mounting and surface mounting with 200 Amps rated copper busbar, with neutral bar, earthbar and cable alley for cable managment, fully shouldered, neutral bars, prefittes masking sheet complete all as specified and as directed.

S&F MCB SPN, AC 240 V, 6 to 32 Amps 10 KA capacity,'C' series making connection with suitable size of copper lugs etc complete all as specified and as directed.

S&F MCB SP, AC 240 V, 6 to 32 Amps 10 KA capacity,'C' series making connection with suitable size of copper lugs etc complete all as specified and as directed.

Supply, laying and testing cable of size 6 Sqmm 2 Core, XLPE insulated, PVC sheathed, conforming to relevant IS, ISI marked, armoured heavy duty, electric cable with aluminium conductor, 1100 volts grade, in trenches/wall/floor/pole complete and making connection including suitable size Aluminium lugs complete all as specified and as directed

Supply, laying and testing cable of size 10 Sqmm 2 Core, XLPE insulated, PVC sheathed, conforming to relevant IS, ISI marked, armoured heavy duty, electric cable with aluminium conductor, 1100 volts grade, in trenches/wall/floor/pole complete and making connection including suitable size Aluminium lugs complete all as specified and as directed

M&L for double walled corrugated (DWC) HDPE Pipe of 50mm bore confirming to IS :16205 Part 24 for laying of LT cables including 90 degree bends with coupler and rubber ring, with all accessories, laid in trenches for LT cable protection all as specified and as directed .

Taking down carefully copper/Aluminum point wiring (Light, Fan, Socket or power) complete with all fitting such as switches, ceiling, regulator, sockets etc and making good disturbed surfaces as directed.

S&F in replacement decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient of capacity 20 Watt , 6500 K with inbuilt driver complete fitting and all other accessories fitting arrangements including connecting up with two core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. Make : Cat No. LHEXACP7IN1W020 of Havells or equivalent of makes specified in PS

M&L for sub main wiring with 2 runs of 4.0 sqmm, FRLS single core, PVC insulated & unsheathed cable, conforming to IS-694, 1100 volts with copper conductor, multi stranded, drawn in and including suitable size PVC Casing Caping (ISI marked) with all accessories such as Tees, Elbows, junction box etc as requied alongwith one run of 4.0 sqmm FRLS single core PVC insulated & unsheathed copper conductor as continuous earth wire dolly and connecting to existing main switch board / distribution board of each building as ordered and testing on completion including taking down old submain wiring and any type of casing/caping/Conduit, complete all as specified and as directed. Note : Three runs of 4.0 Sqmm cable and one run of PVC casing/caping will be measured as one unit.

S&F MCB SPN, AC 240 V, 40 Amps 10 KA capacity,'C' series making connection with suitable size of copper lugs etc complete all as specified and as directed.

Supply and fix exhaust fan, steel body AC single Phase, 230V of size 380 mm sweep with, blades, and frame and louvers including electrical connection with PVC 1.5 sqmm 3 core wire from ceiling rose to Exhaust Fan complete all as specified and as directed by Engineer in Charge. Make - Bajaj/Havells/Orient/Crompton/Usha Location :- as directed by Eng-in-Charge

Supply, installing, connecting, testing and commissioning of electric water heater storage type capacity 25 Liters 5 star rated with inner body feroglas coating technology, resistance,heavy duty protective anode protect the inner container from corrosion,Energy saving high density PUF insulation stores hot water for longer time, precaliberated thermostat, safety valve, fire retardant power cord, Corrosion proof outer body, Colour changing indicator, Heavy duty copper heating element with rated voltage 2 KW, 230 volt, 50 Hz of thermostat cutout temperature 75 degree Celsius, High working pressure of min 0.8 mpa,vertical type with ISI certification mark, installing on wall with suitable size bolts, nuts, etc and connecting up with water and electric connections including hot and cold connection pipes including alteration of existing pipe lines complete all as specified and as directed. MAKE: Havells Fabia Ec Model No :GHWAFATWB025 or equivalent Model of make Bajaj,Usha,Crompton.

NATHKRUPA CONSTRUCTION (BID ID -3410719)

Arihant Construction (BID ID -3415262)

M.H Construction (BID ID -3416289)