Providing Internal and External Electrification arrangements including Lift arrangements to the Construction of Additional Building in Government Hospital at Thirukuvalai in Nagapattinam District.

Amount

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End )

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End

Wiring with 3 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point Higher End

Supply and fixing of single box type 4' 20W LED fitting with LED tube complete with TW round blocks on wall or ceiling with PVC unsheathed Copper leads from terminals to the fitting.

Supply and fixing of single box type 4' 20W LED fitting with LED tube complete with electronic ballast with conduit pipe suspension from the ceiling with PVC unsheathed copper leads from terminals to the fitting with tube.

Supply and fixing of 18W LED square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting

Supply and fixing of WT bulk head fitting with guard suitable with 7W / 9W LED bulb

Supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 600 mm down rod with fan clamp with side plates and cross arm of size 450mm (18")

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete without provision of hole in the wall

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan

supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting .

Supply and fixing of 2 no. 6A two module socket, 1no.6/16 A two module socket , 2 nos. 6A one module switch, 2 nos. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion

Supply and fixing of 3nos.6A two module 5 pin socket , 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End.

Supply and Run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 4 sq.mm. PVC insulated SC unsheathed FRLS copper wire and making good of the concealed portion

Supply and fixing of 20A Flush type Wall Socket 32A DP MCB complete set for AC Plug in flush with wall with earth connection (For AC Plug)

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and Run of 2 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 6 sq.mm. PVC insulated SC unsheathed FRLS copper wire and making good of the concealed portion

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63 A 4P MCB switch as incoming and 12 nos. 6A to 32A SP MCB as outgoing on suitable angle iron frame work on wall with earth connection only. Higher End

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no.100A 4P MCB Isolator as incoming and 4 nos. 63A TP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and Run of 4 of 16 sq.mm. (140/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 4 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour.

Supply and clarnping of 3-1/2 x 50 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3-1/2 x 50 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2x50 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and fixng of TNEB meter board suitable for 3 phase 100A service connection made up of suitable angle iron frame work of size 2 feet x1-1/2 feet using angle iron of size 1-1/2"x1 1/2"x1/4" rigidly fixed on wal covered with hylem sheet of size 2 feet x1-1/2 feet of 12mm thickness with necessary bolts and nuts supports and supply and fixing of 3Nos. 100A fuse units (500V), 1No. neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 16 Sq.mm PVC insulated copper wire with earth connection complete

Supply and fixing of 100A TPN switch disconnector fuse units in sheet steel enclosure with HRC fuses double break on suitable angle iron frame work with MS cable entry boxes with earth connection only.

Supply and fixing of 100 A Three phase 500V 4 Pole Change over Switch on suitable angle iron frame work with MS cable entry boxes with earth connection only

Supply and clarnping of 3-1/2 x 70 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3-1/2 x 70 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2x70 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and erection, testing, commissioning uninterrupted power supply OFFLINE (Sinewave) with copper wound Transformer of 2000VA with Input supply of 230V, 50Hz AC supply with 150 AH Tubular Battery to work at full load capacity including transportation with following 2hour backup specification.1) Input Voltage : 230, 50Hz single phase AC supply 2) Output Voltage : 220V to 240V 50HZ AC supply 3) Battery charging device of suitable rating 4) Circuit board of suitable capacity 5) Over load and short circuit protection 6) Visual Indication for ON/OFF / Trip / battery charging/mains failure/ Low Battery etc., 7) Mode setting for Bypass/Reset 8) 12V 150AH battery - 2 Nos. 9) Trolly for heavy UPS & Battery (SR )(M-2106)

Supply and run of 2 of 1.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade insuitable heavy gauge MS conduit pipe concealed in wall and ceiling with continuous earth wire connection of 1.5sq.mm copper wire and making good of the concealed portion with suitable colour

Earthing as per PWD standard with an earth electrode of 2metre Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection

Supply , erection,Testing Commissioning and Handing over of 1 No 58.5 KVA Diesel Generator Set with acoustic enclosure conforming to CPCB IV+ Norms and BIS Specifications Diesel Generator set of 0.8 P.F. ( lagging) Three phase 415V/ 420 Volts, 50Hz, 1500 RPM CPCB Approved capacity comprising of Engine developing 38 BHP Air cooled clock wise rotating feed pump with 53.5 KW/ 58.5 KVA operating capacity brushless alternator close coupled, underneath fuel tank, standard safeties LLOP with stop solenoid battery with lead Electric start and fitting and accessories confirming to IS and AMF panel as detailed below including transporting & unloading charges. (A) Engine: Water cooled diesel engine suitable for Generator application with a shaft out put of 38BHP at 1500 RPM under NTP conditions. The Engine shall comprise the following standard fittings: Flexible coupling or suitable close compact coupling with guard , flywheel, air cleaner, fan blower type with guard, radiator with guard, water pump engine mounted, fuel pump, lubricating oil filter, lubricating oil pump, governor (mechanical/ hydraulic),flexible exhaust piping of 50cms length exhaust silencer residential type.

(B) 12 Volt Electronic starting Equipment: Complete with starter motor, dynamo, standard 12 V batteries with cable. (C) ENGINE INSTURMEN PANEL / MOUNTED: Starting push botton / starting key, lubricating oil, temperature gauge, lubricating oil pressure gauge, water temperature gauge, safety control for low lubricating oil, pressure, safety control for high water temperature, safety control for over speed, hour meter (mechnical ) and RPM indicator, battery charging ammeter. The engine should be capable of providing 10% over load for one hour for every 11 hours continuous at full load. (D)ALTERNATOR: 58.5 KVA/53 KW Capacity of brushless alternator, AC 3 phase, 50Hz, 415/420V, 0.8 PF ( lagging), 1500 RPM under NTP conditions, conforming to IS:13364 (Part-II)/ 1992 shall be screen protected drip proof ,to be coupled by means of Flexible coupling or suitable close compact coupling to the diesel engine.

8. 1 set Air break contactor with auxiliary netural contactor for main supply 9. 1 set Low volage HRC fuse for the short circuit protection of the main supply 10. 1 set Alternator contactor with auxiliary netural contactor 11. 1 set Three pole bimetal release for over load protection of alternator 12. 1 set low voltage HRC fuse for the short circuit protection of the alternator 13.1 set DC control relays incorporating engine start/ stop and failure to start / lockout 14. 1 set selecor switch auto/ manual 15. 1 no Push button "Start" 16. 1 no Push button "Stop" 17. 1 no Push button "Reset" 18.1 No signal lamp for indicating load on mains 19. 1 no signal lamp for indicating load on set 20.1no signal lamp for indicating set fails to start 21.1no signal lamp for indicating set running 22.1No signal lamp for indicating battery 23. 1set Pilot lamps of 3 nos 24. 40 A four pole capacity MCCB with thermal magnetic release for over load, instantaneous, short circuit and earth fault trip and under voltage .

25.Rectangular copper bus bars (1No for each phase, neutral and earthing terminals) of adequate capacity duly colour coded with head shrinkable PVC sleeves. 26.1No mains voltage monitor 27.Hooter/Audio alarm for indicating set fails to start and for DG O/L. 28.1set Timers 29.Audio and Visual indicator arrangements for: a) Low lubricating oil pressure b) High water temperature c) Over speed 30.1No Earth fault relay 31.Isolator to isolate the neutral Note:- 1. The AMF control panel should be complete with necessary fuses, cables, label, other accessories with neutral isolation arrangements. 2. The engine should trip for the following: a) Low lubricating oil pressure b) High water temperature c) Over speed 3.Supply and fitment of Auto Mains Failure Panel, 1 EB Service wih 100 Amps switch and contactors SUF Control relays, timers etc suitable for auto change over of DG & EB Service.

F.FUEL TANK Fuel tank of 165 litres capacity and with inlet and outlet connections, filling cap drain plug, level indicator complete. G.BASE FRAME: Base frame should be fabricated with MS channel frame of rigidly welded construction for mounting the generaor set. The engine and alternator should be coupled by suitably designed diaphragm type flexible coupling with guard and mounted on the base frame wih proper alignment H. ACOUSTIC ENCLOSURE: The Acoustic enclosure, Self standing weather proof CPCB Typed Acoustic canopy floor mounting type with modular construction with the provision to assemble and dismantle easily and designed to suit all weather condtions. Erection of acoustic enclosure suitable for 58.5 KVA Diesel generator complete with all accessories as above and suitable supports etc.The maximum permissible sound pressure level should be as per the norms prescribed by the central/ state pollution control board or competent authorities or should be 75 db(A) at 1 metre from the enclosure surface.Adequate ventilation to be provided so that generator performance is not affected and temperature rise inside is limited.

The emergency stop &suitable digital display meter for inside ambient temperature to be available on the enclosure panel and glass window to view control panel to be provided The enclosure shall be duly approved by the engine manufacturer of the engine provided for the generator set and should be to the satisfaction of inspecting / testing authorities concerned to suit CPCB norms. I. Manuals & Documentation: Operation & Mainenance manual for Engine, Maintenance Manual for alternator, Engine test certificate, alternator test certificate, circuit diagram for control panel, DG Set test certificate, CPCB compliance label fixed on Canopy. J. First charging of lubricating oil, coolant etc & battery charging for testing and commissioning of the generator set. Free comprehensive service to be provided during the guarantee period of one year

Erection testing Commissioning and handing over of Gen set:- Providing suitable concrete foundation with cement concrete 1:2:4 with sand cushion all around the foundation erection of 58.5 KVA Generator set over the existing foundation and erection of Generator set with proper alignment over the existing foundation to suit 58.5 kva Gen set foundationof Suitable size

Supply and Installation of exhaust piping of sufficient length with suitable MS pipe so as to extend outside the Generator room with necessary thermal insulation

Providing fuel oil to run the set for 8 hours on load testing and commissioning using water rheostat or suitable loading elements

Supply of tools such as 1no. 15” cutting pliers, 1no. 6” screw driver, 2nos. 9” screw drives, 1set of 6nos, double ended spanners, 1no. Adjustable spanner, 1no. ½ Ib hammer, 1no. Spanner for removing engine oil plug, 1no. Line tester required for the maintenance and operation of the generator set -1set.

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class'B' GI pipe of dia not less than 40mm with copper earth plate of size125mmx50mmx6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply and run of 25mm x3mm tinned copper flat with necessary clamps/supports on wall / floor / ground for earth connection

Design, Engineering, supply, fabrication, erection, testing, commissioning and handing over of 15 persons capacity Stretcher Cum Passenger lift with machine room,speed : 1m/s with stainless steel panels,Disable fiendly ,Microprocessor Based Controller ,VVVF Drive ,Fire Rated Doors and ARD as per the following Technical specifications 1. Location : Additional Building in Government Hospital at Thirukkuvalai 2. No of Lift : 1 No 3. Type of lift : Stretcher Cum Passenger Lift 4. Capacity of lift : 15 persons capacity passenger lift (1088 Kgs) 5. Speed : 1 .00Metre / Sec 6. Type of Drive:microprocessor based controller, VVVF drive, Fire rated doors and ARD. 7. No. of Floors : ( G + 1 Floors ( 2 stops ) 8. Total Travel: 7.20 metres 9. Levelling Accuracy: High level accuracy with smooth and jerk free stopping. 10. Construction of Car: 18 SWG High quality stainless steel car and hand rail , PVC flooring, Perspex False ceiling Neat hair line finish and mirror finish in rear panel.

23. Car fittings: LED & Regular (Circular)-Fan with comfortable ventilation inside the car. 24. Lift well: R.C.C. construction with brick masonry.(existing) 25. Indication: UP/Down digital direction and position indicator for all landing and in car 26. Emergency Alarm Bell: Battery operated alarm bell to be provided with Automatic charging device 27. Emergency light: Battery operated light to be provided with Automatic charging device. 28. Fire Man’s switch: To be provided at ground floor 29. Minor builders work: included in the scope. 30. Scaffolding: Included in the scope 31. Sill angles and facia plates: included in the scope. 32. Steel for lift machinery: Included in the scope. 33. Servicing and maintenance: Free comprehensive servicing and maintenance should be provided by lift contractor during the guarantee period of one year. 34. Automatic Rescue device: To facilitate the landing of the lift to the nearest floor at the time of power failure. This shall consists of suitable type battery system with charger, invertor, under voltage protection system etc., complete with all accessories.

35. Provision of intercom with phone: To be provided by lift contractor with one handset in the lift car and another handset in the lift machine room. 36. Lift License: Preparation of Drawing, payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate as per lift act should be done by lift contractor. 37. Floor position: Included with LED display and announciator with music 38. Special features: a. Infra-red door sensor with full height screen b. Stainless Steel signal fixtures. c. Vandal proof S.S. Button with S.S. cover d. SS door frames for landing doors. e. V3F door operator. f. Call Register signal g. Stainless steel facia plate for car operating panel and landing fixtures. h. On-Off switch for fan and light. i.Over load warning indicator with audio announcement

39. Other standard features: Over speed governor, phase failure and phase reversal relay alarm bell, T. Guide brackets for car and counter weight, rubber padding under winding unit, motor of adequate capacity, single reduction worm gear, electro magnetic brake with compression springs car safety gears buffer, electro mechanical door locks emergency key side supporting angles, motor over load protection devices final limit switch main suspension ropes counter weights lifting joint joist for mounting the machineries. 40. Guarantee: Guarantee for the materials and workmanship of equipments complete should be offered by lift firm for a period of not less than one year. 41. Site testing in accordance with IS 14665 should be carried out at the time of handing over. 42. Supply of operation and maintenance manual with necessary tools for operation.

Supply and clamping of 3-1/2 x 35 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3 1/2 x 35 sq.mm PVC Armoured LTUG Cable with earth connection.

Supply and providing cable end termination of 3-1/2 x 35sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

preparation of site plan , physical layout electrical schematic diagram (10 sets) getting drawing, approval from CEIG preparation of competion report rectification report etc ., arranging CEIG inspection Paying CEIG inspection fees and obtaining safety certificate from CEIG and provision of approved drawing with neat frame works and submission of safety certificate

ADD GST

JAYARAJ (BID ID -1375076)

Chandrasekaran R (BID ID -1374708)