SPL REPAIR OF 05 X OR GOVT MD ACCN QTR NO P-114, P-115, P-116 AND P-117 AND P-120 OF 119 FD WKSP AT DOGRA LINE ROORKEE AND SPL REPAIR/IMPROVEMENT OF OH LT LINE TO UG LT CABLE AT MAIN OFFICE, OFFR QTR AND QTR GD AREA AT RTS AND DEPOT SAHARANPUR UNDER

Amount

Demolition of cement concrete (reinforced) of any position not otherwise specifically provided for and including reinforcement required to facilitate demolition upto and including fourth story and on the roof top/ mumty/ parapet/Chimney and removal of debris and rubbish out side MoD land complete all as specified and directed.

M&L for mild steel TMT bars of 10 mm dia and over cut to length bent to shape required including cranking, bending etc and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for providing reinforced cement concrete (1:2:4) type B-1 using 20 mm graded crushed stone aggregate as in kitchen slab complete all as specified and directed.

Form work to sides and soffits of shelves etc including supports such as kitchen shelves, platforms and similar works rough finish surface of concrete (the thickness of slab/shelves n.exc.100 mm) complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in Ground floors and paving n.exe 15cm thickness (below or above ground level) including removal of rubbish out side complex (MOD land), complete all as specified and directed.

M&L 75mm thick cement concrete 1:3:6 type C2 (using 40mm graded stone agg). Plinth protection laid to a slope of 1 in 24 in alternate basis system. Each bay shall not exceed 3m in length. 12mm wide & 75mm deep joint shall be formed between the bays which shall be filled with mastic filling to full depth comprising a mixture of 1 part of hot blow bitumen 85/25 portion and two parts of heated badrapur sand (by volume) etc complete all as specified and directed.

M&L for 75mm thick PCC (1:4:8) ty D-2 using 40mm graded stone aggregates as in levelling course/sub base of path, floor tiles in bathroom and WC.

M&L PCC type B1-1:2:4 (using 20 mm graded crushed stone agg) in roof kerbs or mud stop rounded or chamfered on edge etc complete all as specified and directed

M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregates as in levelling course over RCC roof/floor slabs, cills, steps, parapets, filing in steel chowkats, copings, and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete all as specified & directed

M&L 25mm thick Cement concrete type C-1, 1:3:6 (20mm graded aggregate) as in sub floor and levelling coarse below floor tiles etc complete all as specified and directed .

Supply and laying sand (20 mm thickness) for cushioning to interlocking paver block complete all as specified and directed.

M&L for 60 mm thick Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of M-35 Grade made with grey cement and pigment complete all as specified and directed.

M&L for cement concrete tiles 25cm x 25cm x 20mm thick, using gray cement with pigment, machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished over and including 15mm thick cement mortar 1:4 complete all as specified and directed.

Demolition of brick work built in cement mortar in any description and position complete all as specified and directed.

M & L brick work with sub class "B" bricks straight or curved on plan exc 6 m mean radis built in CM 1:6 complete all as specified and directed.

M&L for Brick work with sub clas "B" bricks straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as specified and directed.

Dismantling of Cast Iron pipe/ RCC drain pipe/PVC pipe up to 150 mm bore complete all as specified and directed.

S&F PVC (SWR) pipes of 110 mm nominal outside diameter (Type B with wall thickness 3.20 to 3.80 mm) single socketed in any length with rubber ring joints including all fittings/fixtures fixed on wall or in trenches or in floor complete all as specified and directed.

All as per item No.18 above but 75mm nominal outside diameter.

S&F PVC (SWR) vent cowl suitable for 75 mm pipe

S&F 110 mm bore PVC (SWR) bends/shoes any radius complete all as specified and directed

All as per item No. 21 above but 75 mm bore.

S&F in repair PVC (SWR) floor trap/Nahani trap, 75mm dia plain including jointing with solvent cement with grating including jointing to waste pipe in cement concrete complete all as specified and directed.

S&F PVC (SWR) reducers 110mm dia, complete all as specified and directed.

S&F in repair 110 mm pipe stack clamps out of 50mmx 5 mm flat iron including bolts and nuts and securing ends of stays to walls or roof complete all as specified and directed.

All as per item No.25 above but 75 mm bore pipe.

S&F PVC (SWR) junction, 110mm dia (Single T) or unequal provided with access door complete all as specified and directed.

Cutting into existing manholes for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 or 3/4 section ) in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate finished smooth and reforming benching as required for 100/150mm dia pipes complete all as specified and directed.

M&L Non-skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and incl 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for joint free coloured glazed ceramic tiles in vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick rendering in CM 1:4 complete all as specified and directed.

S&F vitrified tiles coloured of 7 to 8 mm (squre/ rectungular ) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors set and jointed in neat cement slurry and pointed with white or coloured cement over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

S&F Vitrified tiles coloured of 7 to 8 mm (squre/ rectungular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in skirting, dado etc set and jointed in neat cement slurry and pointed with white or coloured cement over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

Dismantling floor or wall tiling in old cement motor removing and rubbish off the permisses complete all as specified and directed.

M & L for 16-18 mm thick mirror polished Machine cut kota single piece stone slab of size 22''x22'' for flooring over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab laid over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L kota stone mirror polished slab with uniform texture of 16-18 mm thick in trader of steps (to be flushed and provided with three Nos of grooves at the end on each step), riser of steps, skirting, dado and pillars in one single piece (size decided by Engineer-in-Charge) laid over and including cement screed 10mm thick in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing , bevelled edge of corner etc complete all as specified and directed.

M & L for granite 20 mm thick (table rubbed and polished) in cooking platforms and laid over cement screed mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl moulding of front side complete all as specified and directed.

Dismantling of any tiles or terracing tiles, single layer on roofs, kerbs, aprons, floor, wall etc. (each layer) and removal of rubbish out of defence land complete all as specified and directed.

Demolition of Mud Phuska in roofs,any thickness including plastering and leeping of any thickness upto 30cm deep complete all as specified and directed.

M&L for 40mm thick brick tiles laid on 15mm thick cement mortar (1:6) and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on RCC surface complete complete all as specified and directed.

M&L for rendering 20 mm thick cement plaster in CM (1:3) finished even and smooth w/o using extra cement and using waterproofing compound on fair faces of brick work or concrete surfaces complete all as specified and directed. NOTE: WPC will be measured and paid for separately.)

Taking down old existing water proofing treatment from the top of RCC / arch slab and hacking the top of RCC slab, cleaning with water and disposal of rubbish off the premises complete all as specified and directed

Material & labour for cleaning of concrete or plastered surfaces of roof and applying priming coat using with bituminous primer @ 0.30kg per Sqm followed evenly by a tack coat @ 1.20 kg per Sqm using 85/25 grade industrial hot blown bitumen, over it laid with 3mm thick APP modified polymeric water proofing membrane minimum weight 3.00 Kg per Sqm reinforced with non-woven polyester fabric (weight not less than 160 Gm per Sqm) unrolled & bonded to substrate with side and end laps 75mm & 100mm as per manufacturer’s instruction and applying over it a tack coat using 85/25 grade industrial hot blown bitumen @ 1.20 kg per Sqm and finally finished the top of polymeric water proofing membrane with a coat of bituminous aluminum paint @ 0.20 kg per Sqm as per manufacturer’s instructions over, complete all as specified & directed.

Taking down chowkhat or frames exc. 1.5 Sqm and n.exc 4 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed.

Taking down chowkhat or frames not exc. 1.5 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed.

Taking down shutter only exc 1 Sqm but not exc 2 Sqm each amd refixing in same opening complete all as specified and directed.

Supply & fixing factory made pressed steel frames for doors with one or more rebates including necessary fitting lugs, hinges, lock strike plates etc completed size of frame 165x60mm made out of 1.25mm MS sheets including PCC 1:2:4 Ty B0 using 12.5mm graded stone aggregate as in frame complete all as specified & directed.

Supply & fixing factory made pressed steel frames for doors with one or more rebates including necessary fitting lugs, hinges, lock strike plates etc completed size of frame 105x60mm made out of 1.25mm MS sheets including PCC 1:2:4 Ty B0 using 12.5mm graded stone aggregate as in frame complete all as specified & directed.

Cutting holes in brick walls exc half bk wall but n exc one bk wall built in cement mortar or cement lime mortar and stone walls built in lime mortar or for inserting holdfasts and making good dismantalled portion in CM (1:3) or cement concrete (1:2:4) type B1 as required complete all as specified and directed.

S&F M.S work as in holdfasts, wind ties, plane angle cleats for securing purlins to wooden trusses or rafters etc complete all as specified and directed.

S&F factory made steel shutter shall be made out of angle iron 35x35x5mm and 3 nos 25x25x3mm as cross support in frame of door and covered with 1.00mm thick MS sheet, running welding with frame, with locking arrangement complete all specified and directed

S&F 35mm thick factory made Glazed and skeleton shutters using second class hard wood, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F30mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed..

M&L for built in steel cup board with pressed steel frame of size 75 mmx45mmx1.25 mm th with pressed steel shutter 1mm th Godrej pattern fixed to masonry wall by hold fast made out of 25x3 mm flat iron including ms hanging rod of 10 mm dia with bracket fixed on inner side of one leaf of shutter and on other leaf provision of ms peg set of 3 pegs including spray including locking arrangement complete all as specified and directed.

S&F factory made gauged shutter shall be made out of angle iron 35x35x5mm (outer frame) and 25x25x5mm (middle rail 2 nos, 150 mm apart from each other) and 1.0mm thick steel sheet covering on middle rail, 10mm Square bars @ 100mm C/C fixed vertical as grill complete with stainless steel fly proof wire mesh having 0.63mm nominal dia wire and 1.4mm average with aperture, with locking arrangement all specified and directed.

S&F Fiber glass reinforced plastic (FRP) Flush door in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF) polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameter of FRP, laminate confirming to table 3 of IS -14856 Complete all as specified by the manufacturer and as per direction of Engineer -in- charge.

S&F FRP door frames three legged of cross section 90x45mm having single rebate 32mmx15mm. The laminated door frame moulded with fire retardant grade unsaturated polyester resin and chopped mat. Door frame laminated shall be 2mm thick, frame shall be covered with fiber glass from all sides MS flat iron 25x3mm shall be provided at the bottom to steady the frame including PCC 1:2:4 Ty B0 using 12.5mm graded stone aggregate as in frame, complete all as specified and directed.

S&F 100 mm long (size) butt hinges, stainless steel AISI 304 grade with brass/bronze hinge pin, complete all as specified and directed.

All as per item No. 57 above but 75 mm long.

S&F 300mm long, stainless steel of AISI 304 grade, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts complete all as specified and directed.

S&F Stainless steel of AISI-304 grade barrel tower bolt 200 mm long, extruded section complete all as specified and directed.

All as per item No. 60 above but 150 mm long.

S&F stainless steel handles of size 150mm size long complete all as specified and directed.

S&F Floor door stopper of stainless steel body and tongue, with hard drawn steel spring, fixed in floor of 140mm long complete all as specified and directed.

M&L Preparation of new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L Preparation of new or previously untreated steel and steel based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, complete all as specified & directed

M&L for powder coated aluminium anodised window sliding type (3 shutters type) with sash bars, aluminium sections weighing 0.55 Kg/m(min) S&F stainless steel wire cloth 0.36mm nominal dia of wire and width of aperture 1.40mm and 03 to 04 mm thick pin headed glass complete, necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws suitable anodised fittings such as, hinges, handles, including anodised aluminium frame. Note - (i) Weight shall be measured before fixing of glass and wire cloth. (ii) Rate quoted by contractor including all aluminum frame, shutter, glass & wire cloth etc.

M&L for powder coated (50 micron thick) aluminium ventilator fixed type (partly glazed and partly gauzed) with gasket, glazing clip etc, weight of frame not less than 0.55 Kg/RM and weight of shutter frame not less than 0.425 Kg/RM including necessary joining cleats,rubber packing, anodised aluminium snap beading, screws suitable anodised fittings such as, hinges. Note - (i) Weight shall be measured before fixing of glass and wire cloth. (ii) Rate quoted by contractor including all aluminum frame, shutter, glass & wire cloth etc.

S&F stainless steel (grade-304) grills made of hollow tubes section including welding, grinding, buffing polishing and making curvatures wherever required and fitting the same with necessary holdfasts/ SS dash fastners with nut & bolts of required size, complete all as specified and directed.

S & F in repairs for 18mm thick Multi layer water proof ply wood fixed with screws to timber frame work for cabinet case both sides covered covered with and including cost of 0.8mm thick decorative laminates, Mica type 1 of surface finished, colour, pattern as approved fixed with adhesive and the thickness of the shutter is edge lipped by 18 mm width x 1 mm thick PVC sheet using solvent cement etc. including, magnet, piono hinges, handles as required Nos complete as direction of GE, manufacturer's specification and drawing complete all as specified and directed.

S & F in repairs for 9 mm thick Multi layer water proof ply wood fixed with screws to timber frame work for cabinet case both sides covered with and including cost of 0.8mm thick decorative laminates, Mica type 1 of surface finished, colour, pattern as approved fixed with adhesive and the thickness of the shutter is edge lipped by 9 mm width x 1 mm thick PVC sheet using solvent cement etc. including ,magnet, piono hinges, etc complete as direction of GE, manufacturer's specification and drawing complete all as specified and directed.

M&L MS Frame work as in door chowkhat with angle iron welded together ends of angle shouldered and fixed to opening and welding 3 Nos mild steel butt hinges, and 6 nos hold fasts made out of FI 25x3 mm 30 cm long for fixing of chowkhat (Butt hinges paid separately) complete all as specified and directed

Taking down cement plaster, terrazzo dado in any thickness from brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc including removal of rubbish, vegetation etc outside complex (MOD land) complete all as specified and directed.

M&L Rendering 5mm thick plastering in cement mortar 1:3 as in ceiling finished even and smooth without using extra cement to match with existing surface complete all as specified and directed.

M&L Rendering 12 mm thick in cement mortar 1:6 on fair face of brick work/ concrete surfaces (either surfaces) of wall and finished even and smooth without using extra cement complete all as specified and directed.

M&L Rendering 15 mm thick in CM 1:4 on external fair faces of brick/concrete work surfaces finished even and smooth (without using extra cement) complete all as specified and directed by Engr - in - charge.

Supply only liquid water proofing compound complete all as specified and directed.

Complete removal of existing treatment on surfaces of walls by scrapping down with mechanical grinder on old walls as per the specification of manufacturers instructions of paints/OBD complete all as specified and directed.

M&L for Preparation of new plastered surface or old treated surface of wall by applying 2mm thick wall care putty and making the surface smooth and applying two coat of oil emulsion distemper using roller for painting complete all as specified & directed.

M&L for Preparing of new plastered surface of wall and finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade over and includling 2mm thick wall care putty (Two or more coats applied @1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm complete all as specified & directed

All as per item 80 above but for old surface by complete removal of existing treatment by scrapping down with mechanical grinder on old walls as per the specification of manufacturers instructions of paints complete all as specified and directed.

M&L for preparation of newly plastered surface of ceiling and applying three coat of white wash complete all as specified and directed.

All as ser item No.82 above but one coat on old ceiling surface.

Taking up or down 15 mm bore GI tubing and connections complete all as specified and directed.

All as per item No. 84 above but 20 mm bore

S&F 15mm bore GI tubing medium grade with all fittings and fixed to wall and ceiling or laid in floors etc complete all as specified and directed.

All as per item No 86 above but 20 mm bore.

Cutting chases on brick or concrete surface for concealed water tubing or girth n.exc 10cm including making good of disturbed surfaces with PCC 1:2:4 type B0 using 12.5 mm graded aggregate complete all as specified and directed.

Dismantling of RCC/ PVC water tanks exc 250 liters and n.exc 500 liters capacity of any condition or type complete all as specified and directed.

S&F white colour Rotational moulded polyethylene water storage tank 500 liters capacity, white triple layer construction (cylindrical vertical closed top), hoisted & fixed in position including all fittings complete all as specified and as directed.

S&F in repair Gun-metal globe or gate valves 20mm bore with iron wheel head, screwed both ends for iron complete all as specified and directed.

S&F in repair 20 mm Ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight 210 gms) complete all as specified and directed.

S&F in repair vitreous china wash hand basin (WHB) size 550mm x 400mm, Ist quality, including provision of pair of mild steel angle iron brackets of suitable size duly painted and cutting for and pinning in ends of brackets in walls & making good & including providing and fixing of suitable heavy duty waste pipe and waste fitting complete all as specified and directed.

S&F in repairs PVC duel action symphonic action type flushing cistern 10 ltr capacity, low level, white with inlet, ball valve and float including brackets and flush pipe complete all as specified and directed..

S&F in repair stainless steel sink AISI 316 grade without drainage board of 1 mm thick with plug , washer and waste, including bedding in cement mortar to dwarf wall or including CP Waste , PVC Down pipe etc and fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowlsize 410mm x 330mm x 160mm or more complete all as specified and directed..

S&F in repair Chromium plated tubular towel rail, 25mm dia, ‘D’ type 60cm long between flanges of brass chromium plated and with hooks,brackets & End caps fixed with brass screws complete all as specified and directed .

Supply & fix wall mixer with over head shower chromium plated for mixing hot and cold water screwed for iron pipe suitable for 15mm bore pipes complete all as specified and directed.

S&F in repair Brass chromium plated shower rose 125mm size with CP breass arm not less than 240mm long complete all as specified and directed.

S&F in repair Stainless steel cromium plated Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repairs 15mm bore Pillar tap of Chromium plated high pressure screwed for iron pipe and fixed etc. complete all as specified and directed.

S&F in repair, Sheet Glass Shelf/corner Assembly, consisting of 5.5mm thick Sheet Glass Shelf 12 Cm Wide with Chromium plated Bracket Guard and Railing 60 Cm long, complete all as specified and directed.

S&F in repair Stainless steel 4 shelf wall mounted kitchen utensils rack, Dish rack with plate,& cutlery stand of size 18x24 inches , fixed to wall plugs and chromium plated brass screws complete all as specified and directed.

S&F in repiars vitreous china squatting pan (Orissa pattern) long pan including provision of cement concrete (1:5:10) bedding fixed in repair size 580x440mm white with intergral footrest with 'P' or 'S' trap complete (excluding flushing cistern and flush) Complete all as specified and directed

S&F in repair stainless steel peg set of six of size 480x38x2mm complete all as specified and directed.

S&F in repair 15 mm dia stop cock/angle cock cast copper alloy chromium plated screwed down high pressure with crutch or butterfly handle,with long shank and cup flench screwed both ends for iron or for union complete all as specified and directed.

S&F in repair bib taps fancy type brass cromium plated 15 mm bore size screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair Stainless steel grating 100mm dia of best quality as approved including fixing in CM 1:4 to floor/nahani traps etc complete all as specified and directed.

S&F in repair PVC connection 15 mm bore and 45cm long with washers complete all as specified and directed.

M&L for cutting hole of 230x230x230mm four Nos in walls, filling with PCC (1:2:4) Ty B-1 using 12.5mm thick stone aggregate incl fixing of 1Nos angle iron of size 50mmx50mm x6mm in C shape supported with 02x50x50x6mm angle iron down side angular shape over all lenght approx 6.22 Rm each stand including running welding with other angle, incl 2 coat of synthetic enamal paint over a coat of red oxide primer complete all as specified and directed.

S&F in repair Curtain rod Stainless steel fancy type curtain rod 20 mm dia incl Brackets and knobs complete all as specified and directed.

M & L for cutting of bushes small trees (Peepal small plants etc) trunks shrubs of any dia and girth from roof projection, chajjas, wall junction parapet etc at any height by necessary demoliton of brick work etc if requried and making good distrubed surfaces to match with existing finihes with and incl material and labore in CM 1:4 mixed with WPC /PCC 1:3:6 type B0 /Bk work in CM 1:4 as required at site and as directed by Engr-in-Charge

S&F in repair PVC heavy duty waste pipes of 40/32mm bore suitable for wash hand basins/sinks/flushing cistern complete all as specified & directed

Dismantling of floor of WC and bath not exc 500mm deep and removing out the cinder/concrete from sunken portion, cleaning of RCC surface to remove dust, loose particle with compressed air or any other suitable method depending on site conditions, grinding any sharp edges etc complete all as specified and directed. (b) Cleaning or RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc. (c) M&L for a glass fiber reinforced acrylic modified cementitious coating system with base coat @ 1.50 Kg/Sqm glass fiber reinforcement and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or MC Bauchemie India Pvt Ltd. (d) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with as specified. (e) M&L for providing 25mm dia GI pipe spout projecting at least 150mm beyond outer face of wall. (f) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed. (g) The area of Each WC portion is n.exc 2.00 Sqm each. (h) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account.

M&L for repair to RCC chajja (irrespective size) by cleaning, replastering in cement mortar 1:3 mixed with integral water proofing compound over 40mm thick( average) PCC padding in CM 1:2:4 Type B-O (mixed with water proofing compound) to a required gradient or slope as directed by Engr-in-Charge and the plaster will extended upto 300mm on wall/roof surface to avoid leakage/seepage. Junction of old and new plaster will be well bonded with application of water proofing compound. Drip course or groove of siae 25mm x 4mm will be provided at the edge of bottom surface of the chajja. (Note:- Rates for cement plaster, WPC, PCC and formwork and specilist labours etc required for full completion of item shall be deemed to be included in the rates quoted against this item of BOQ by the contractor).

S&F in repairs stop cock 15 mm bore ISI marked fancy type (Concealed) cast copper alloy, screw down high pressure with crutch or butterfly handle screwed both ends suitable for iron pipe of 15mm bore complete all as specified and directed.

M&L 15 mm thick rendering in cement mortar 1:4 inside and outside wall of manhole, drain etc of brick work/concrete surfaces finished even and smooth (with out using extra cement) complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (20 mm graded aggregate) as in copping, surface channel, benching of manhole/drain etc slightly rounded or chamfered angles and throating, as directed incl finish the surfaces smooth without using extra cement complete all as specified and directed.

Dismantling structural steel work including doors, gates, railings etc, but excluding framed truss etc.

Dismantling and taking down carefully U/S copper /aluminium point wiring (light, fan, socket, power) complete fitting such as switches, ceiling roses, pendants, lamp holder, light fitting etc including CI/Pressed steel terminals, switch box, and making good the disturbed surface of wall/floor etc, to match with the existing surfaces of wall/floor complete all as specified & directed.

Dismantling and taking down carefully sub-main wiring/service wire of any size including wooden batten etc and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc. complete all as specified

Dismantling and taking down carefully existing DB’s any type and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc. complete all as specified

Material and labour for point wiring with 1.5 sq mm PVC insulated, unsheathed, stranded copper conductor (FRLS-H) cable single core 1100 Volt grade in and including rigid PVC conduit medium grade 20mm dia or more ISI Marked concealed conduit and conduit accessories and cutting chases of suitable girth where required on brick/concrete surface & making good disturbed surface,provision of GI/Pressed steel terminal switch box with plastic laminated sheet 3 mm thick fixed with brass screw and washers along with 1.5 sq mm PVC insulated unsheathed stranded copper conductor cable (FRLS-H) as earth wire connected with main common earth dolly complete all as specified and directed for the following :-

One light/fan/bell/exhaust fan point controlled by one, one-way Piano type switch 5/6 Amp complete all specified and directed.

One 3pin/5pin 5/6 Amps socket out let on same board controlled by one, one-way Piano type switch complete all specified and directed.

One 3pin/5pin 5/6 Amps socket out let on independent board controlled by one, one-way Piano type switch complete all specified and directed .

One light point controlled by two,two way piano switch 5/6Amps complete all as specified & directed.

All as per item No 123 here-in-before but wiring with 2.5 sqmm single core multi stranded copper condcutor 1100 V grade PVC insulated (FRLS-H) but unsheathed single core for 16 Amps power point on independent board and 2.5 sqmm (FRLS-H) cable as earthwire complete all specified and directed.

S&F switch piano flush type white finish 5/6 Amps, single pole one way, 230 volts, 50 hz complete all as specified & directed.

S&F switch piano flush type white finish 5 Amps, single pole two way, 230 volts, 50 hz complete all as specified & directed.

S &F socket out let 2 pin 5/6 Amps & 3 pin 5/6 Amps flush type, 230 volts, 50 hz all as specified and directed.

S&F switch piano flush type white finish 15/16 Amps single pole one way, 230 volts, 50 hz all as specified and directed

S &F socket out let 5 pin 15/16 Amps & 3 pin 5/6 Amps flush type, 230 volts, 50 hz all as specified and directed.

S&F fan regulator socket, flush type stepped type, electronic, 450 watt complete all as specified and directed.

M&L bell push AC, SP 240volts flush type 5/6 Amps, 230volts 50Hz complete all as specified and directed

S&F bell ding dong electric 230V AC single pole all as specified and directed

M&L ceiling rose 3 terminal / PVC/ polycarbonate, isolated body all as specified and directed

Supply and fixing sheet metal enclosure double door type for VTPN (Triple Pole and neutral) 415 Volt AC 4 way with 200 Amps rated busbar all as specified and directed.

Supply and fixing sheet metal enclosure double door type for MCBs DB SPN (Single pole and neutral) 240V AC 8 way with 200 Amps rated busbar all as specified and directed.

Supply & fixing MCB, SP, AC, 240 volts of 06 to 40 Amps capacity 10KA, 'C' series and making connections with suitable size of copper lugs complete all as specified & directed.

Supply & fixing MCB, SPN, AC, 240 volts of 63 Amps capacity 10KA, 'C' series and making connections with suitable size of copper lugs complete all as specified & directed.

Supply and fix MCCB 100A, 16 KA, 4 Pole, 415 V, 50 Hz with fixed thermal magnetic release fixed in Vertical TPN complete all as specified and directed.

Supply and fix in replacement of LED batten type body pre-wired with bipin holders,connector block complete with all accessories including 20 Watt (4 feet) retrofit LED tube with Polycorbonate body, full white and connecting up with pvc insulated and pvc sheathed twisted three core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting complete all as specified and directed. Note: Single / double side connection will be as per direction of Engineer-in-Charge.

Supply and fix in replacement of old unserviceable LED mirror light fitting integral slim LED batten integral 9/10Watts of 2 feet long internally pre wired complete with all accessories and including connecting up with PVC insulated and PVC sheathed twisted two core wire of suitable size complete all as specified and directed

Supply & fixing lamp holder (Angular/Straight ), insulated body, with back plate for batten fitting complete all as specified & directed.

S & F LED Bulb 9 Watt (cool day light) having colour temp 6500 K and lumen output 850 suitable for "B-22 type to fix on batten holder complete all as specified and directed.

S&F building security light 30Watt, IP66 LED street light with aluminium pressure die cast housing including brackets made out of 40mm dia GI pipe light grade,bend to shape incliding 02 Nos flat iron clamps, nut & bolts and connection complete all as specified and directed

Supply and fixing sub main wiring two single core 6 sq mm PVC insulated unsheathed stranded copper conductor cable (FRLS-H) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium grade concealed in wall along with 6.00 Sq mm PVC insulated unsheathed copper conductor cable (FRLS-H) as earth wire and wire connected with main earth dolly including cutting chasing and making good disturbed portion all as specified and directed

M & L for Circuit/submain wiring with single core (FRLS-H) PVC insulated copper stranded conductor cable drawing into existing PVC rigid conduit surface/concealed/casing caping as required of 1.5 Sqmm for Inverter wiring, including taking down unserviceable existing wiring etc complete all as specified and directed.

Supply and fix in replacement of 1200mm sweep ceiling fan (BLDC) complete with blades, down rods, electronic regulator and accessories 230V, with minimum air delivery 245 CFM for fixing the fan in ceiling & making good including making electrical connection with ceiling rose including taking down existing unserviceable fan of any description complete all as specified and directed.

S&F in replacement of Exhaust fan Steel body AC single phase 230/240 Volt of size 300 mm sweep complete with louvers including making whole and grouting of nut bolts etc and making good the disturbed sufaces of wall all as specified and directed. Note: Old Exhaust fan to be deposited in MES store Yard

S&F in replacement of PVC air ventilation (exhaust fan), 250mm with louvers, single phase, 230V AC including necessary fittings and M&L for fixing arrangement on wall with frame hold fastener, bolt, washener etc including connection with PVC insulated PVC sheathed copper cable of size 0.5 sqmm from ceiling rose to exhaust fan including finishing and making good as per existing surrounded wall complete all as specified and directed

Supply and fix electric water heater,storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and directed.

Supply and laying or fixing or passing through pipe 1100volts grade heavy duty cable with XLPE insulated multistranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or strip and overall PVC sheathed 25sqmm nominal cross section, 4core in service connections as per IS 7098(Part1) including connecting on LT OH line/LT panel/DB with suitable lugs, glands, binding wire etc complete all as specified and directed

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m depth for laying of GI Pipe/LT cable and getting out in any type of soil complete all as specified and directed.

Returning, filling, including leveling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Removing excavated material not exc 50m and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

M&L for fine sand free from sharp material as in filling in trenches for cable protection incl necessary punning and consolidation as reqd complete all as specified and directed.

S&F GI Pipe light grade of bore size 50 mm for cable protection complete all as specified and directed.

M&L for cutting the existing floor/roads for laying of cable/Gi pipe and making good the disturbed surface with PCC 1:2:4 type B1 (using 20 mm stone aggregate) complete all as specified and directed.

M&L for laying bricks in protection covers cables using sub class B old size bricks complete all as specified and directed

Supply, Installed & fix maintenance free earthing copper bonded steel earth rod of 10 feet long having diameter of 17.2mm with copper bonding thickness of 250 micron, UL listed, CPRI Tested at 25 KA fault current for one second and is provided with universal clamp made of SS earth enhancing compound shall be of 30kg/pit (resistivity is less than 0.12 Ohm meter) tested as per IEC 62561-7. The bove arrangements shall be provided with heavy duty earth poly plastic pit cover of 6000 kg load bearing capacity (Size:270 x 40 200mm) complete all as specified and directed.

Supply and lay cable XLPE Insulated screened PVC bedded galvanized steel strip and wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded alluminium conductor of size 300 Sqmm 3 x 1/2 core.

-do-but size 240 Sqmm 3.5 core

-do-but size 150 Sqmm 3.5 core

-do-but size 95 Sqmm 3.5 core

-do- but size 70 Sqmm 3.5 core

-do-but size 50 Sq mm 3.5 core.

-do-but size 35 Sq mm3.5 core.

-do- but size 25 Sqmm 4 core

-do-but size 10 Sq mm 4 core.

-do-but size 10 Sq mm 2 core.

M&L for laying GI tubing light grade 80 mm dia with all fittings for cable protection including GI clamps nut bolts and washer etc complete all as specified and directed.

M&L cutting PCC/floor/road and taking out cable and making good with PCC including material as per existing after laying of pipe for cable protection complete all as specified and directed at site of trench not more than 0.30 x 0.30m, complete all as specified and directed.

M&L for Earthing complete with galvanised steel earth plate electrode 60x60cmx6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less 'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion complete all as specified and directed.

Supply and fixing stay assembly for HT/LT Pole comprising of 7/3.15mm galvanized steel stranded stay wire of required length fixed to pole with and including clamps fabricated out of MS Clamps 50 x 6 mm flat iron including nuts, bolts and washers, MS galvanized stay bow 14mm dia 400mm long galvanized steel stay rod 16mm dia, 1800mm long with ratchet type nuts & bolts and stay plate, galvanized thimble 02 Nos, loop insulators 65mm x90mm clearance dia of hole 16mm all as specified and shown in electrical plate No. 1 of MES SSR including all necessary excavation and earth work, PCC (1:3:6) type C-2 using 40mm graded stone aggregate, embedded block and disposal of surplus soil to a distance not exceeding 50mtr complete all as specified and directed.

Supply & fix PVC Junction box of size 250x200x105 mm with Aluminium bus bars 04 Nos fixed on pole with the help of MS nuts bolts and MS clamps-1 Nos of size 40mm X 5mm thick with one No MCB SP 6 Amp capacity includes making suitable hole on pole to take out connections to fitting if required at site and PVC insulated sheathed multistranded copper conductor 3 core 1.5 Sqmm for making connection from junction box to security light fitting complete including cable glands for incoming and outgoing cables all as specified.

M & L for Horizontal Boring of holes under road, pavement, hard standing by trenchless technology using GI Pipe of required dia and necessary machine suitable for 0.4 mpa working pressure. Note :- GI pipe medium / Light grade will be measeured and paid saperately under respected item.

INCOMINGS (a) MCCB 4 POLE 415 V 400 A (36 KA) -01 No (adjustable type) (In coming) OUTGOINGS (a) MCCB 4 POLE 415 V 315 A (36 KA) -01 No (adjustable type) (MES COLONY & Connected area) (b) MCCB 4 Pole, 415 V, 160 A (25 KA) -02 No (adjustable type) (MES & PH 1 & 4) (01 Spare) (c) MCCB 4 Pole, 415 V, 100 A (25 KA) -02 No (adjustable type) (Work shop & Offr Qtr) (d) Digital type Multi function meter (Ammeter & Voltmeter)-1 No Each (e) Indicater - RYB - 1 Set (f) Aluminum bus bar 800 Amps rating 3 Nos for phases and one No for Neutral

INCOMINGS (a) MCCB 4 POLE 415 V 100 A (25 KA) -01 No (adjustable type) (IN) OUTGOINGS (a) MCB TPN 415 V 63A -06 No (b) Digital type Multi function meter (Ammeter & Voltmeter)-1 No each (c) indicater - RYB - 1 Set (d) Aluminum bus bar 300 Amps rating 3 Nos and one for Neutral

INCOMINGS (a) MCCB 4 POLE 415 V 400 A (36 KA) -01 No (adjustable type) (IN) OUTGOINGS (a) MCCB 4 POLE 415 V 250A (36 KA) -02 (Main ofc, RD I) (b) MCCB 4 Pole, 415 V, 200 A (36 KA) -01 No (GO godown to Main gate)-02 No (c) MCCB 4 Pole, 415 V, 100 A (25 KA) -01 No (Break stable area) (d) MCB TPN, 415 V, 32 A -01 No Security light (e) Digital type Multi function meter (Ammeter & Voltmeter)-1 No each (f) Indicater - RYB - 1 Set (g) Aluminum bus bar 800 Amps rating 3 Nos and one for Neutral

INCOMINGS (a) MCCB 4 POLE 415 V 250 A (36 KA) -01 No (adjustable type) (IN) OUTGOINGS (a) MCCB 4 POLE 415 V 125A (25 KA) -03 No (RD I- 1, Main Office-1 & Spare -1) (b) MCCB 4 Pole, 415 V, 100 A (25 KA) -01 No (Office) (c) Digital type Multi function meter (Ammeter & Voltmeter)-1 No Each (d) Indicater - RYB - 1 Set (e) Aluminum bus bar 300 Amps rating 3 Nos and one for Neutral

Supply and fix PVC 3 core 1.5 Sqmm copper cable for connecting Cable Jn box to the light point on the pole complete all as specified and directed.

Dismantling cross-arms of M.S. channel or angle sections etc complete and setting aside for re-use with in 50m complete all as specified and directed.

Dismantling of insulators any type any size

Dismantling of ACSR conductors for the pole complete all as specified and directed.

Dismantling steel poles/ struts, any size from ground and removal from site complete all as specified and directed.

Dismantling concrete poles/ struts, any size from ground and removal from site complete all as specified and directed.

AJAY KUMAR CONTRACTOR (BID ID -3158468)

Shikha Enterprises (BID ID -3159259)

M/s badrinath Traders (BID ID -3158780)