GE/SRA/T-41/2025-26

Amount

SCHEDULE 'A' PART-I (BUILDING WORKS)

Demolition Cement Concrete (un-reinforced) of any description in Ground Floors, Paving, etc. not exc. 150mm thickness (above or below Ground Level) and removing debris, etc. to Outside MD/AF Land, complete all as specified and directed.

M&L for Hardcore of broken stone or boulder of gauge not exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for Cement Concrete 1:4:8 type D2 (40mm Graded Stone Aggregate), 100mm thick, as in Sub-bases of floor, path, hardstanding etc complete all as specified and directed.

M&L Cement Concrete 1:2:4 type B0 (12.5mm graded stone aggregate) 25mm thick in Sub-base for laying of Tiles in Floor, complete all as specified and directed.

M&L for providing outdoor type heavy duty ceramic Floor (Paver) Tiles, 400 x 400 x 10mm thick, having geometric patterns, Anti-skid type, Impact Resistant, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade, laid over and including 15mm thick Screed Bed in Cement Mortar 1:4, complete all as specified and directed. NOTE: Cost of Cement Screed Bed shall deemed to be included in the quoted rate.

M&L Providing, cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in coping finished even and smooth without using extra cement complete all as specified and as directed.

M&L for laying 60mm thick factory made pre-cast cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, laid in required pattern over compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand and removing from site complete all as specified and directed. (NOTE: Sand cushioning shall be measured and paid separately)

M&L for sand cushioning with clean river sand duly clear of residual, organic and deleterious materials spread evenly to uniform thickness over PCC Sub Base complete all as specified and directed.

M&L for providing non-skid/matt finish Ceramic tiles, coloured, 7-8 mm thick (Square / rectangular), area of each tile exc 0.11 Sqm but not exceeding 0.18 Sqm in Flooring, set and jointed in Neat Cement Slurry and pointed in White or Colour Cement to match the tiles laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and directed. NOTE : Cost of Cement Screed Bed shall deem to be included in the Quoted Unit Rate.

M&L for Coloured Glazed Ceramic Tiles in vertical surface 450mm X 350mm X 6-7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the Tiles, laid over and including 10mm thick rendering as Screed or backing coat of wall tile in Cement Mortar 1:3, complete all as specified and directed. NOTE : Cost of Cement Screed Bed shall deem to be included in the Quoted Unit Rate.

M&L for providing Granite (of any type) Slab, table rubbed and polished, 12-14mm thick, machine cut, in wall lining (veneering to walls), fixed over and including 10 mm thick cement screed (1:3) and jointed with suitable stone adhesive (as per manufacturer's recommendations), slabs fixed with spacers to provide uniform joints and after setting of adhesive, removing the spacers and filling the joints with suitable epoxy grout and pointed with grout complete all as specified and directed. NOTE : Cost of cement screed bed, tile adhesive and epoxy grout shall deemed to be included in the quoted rate.

Taking down Cement Plaster including raking out Joints, hacking for Key, scrubbing down with Water and removing Debris, etc. to Outside MD/AF Land, complete all as specified and directed.

Taking down damaged/unserviceable Steel / Wooden Chowkat or Frame, area exc. 1.50 Sqm but not exc 4.0 sqm Each, with shutter (without taking off shutter from the frame) and removal from site complete all as specified and directed.

M&L for brickwork with fly-ash bricks (with old size bricks), straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed

M&L Rendering (Internal) 15mm thick in Cement Mortar 1:6 on other than fair faces of Brick Walls, Surfaces finished Even and Smooth without using Extra Cement complete all as specified and directed.

M&L for preparing New/Undecorated Plastered Surfaces of Walls, applying a coat of suitable cement primer followed by a Coat of 2.0 mm thick Wall Putty (in two layers of 1mm thick) incl rubbing down with Sand Paper to obtain a smooth finish surface and finishing with Two Coats of Acrylic Distemper (as approved) as per desired shade/tint complete all as specified and as directed.

M&L preparing old Distempered surfaces of Walls including filling the existing Nails/Screw Holes, etc. and applying Two Coats of Acrylic Distemper/OBD (of approved tint) with rollers complete all as specified and directed.

S&F 0.50 mm thick TCT (total coated thickness) pre-coloured galvalume sheets with minimum base metal thickness of 0.45 mm, single skin high rib/multi rib profile galvalume sheeting having 1000-1020 mm width and 28-30 mm high crest @ maximum 250-255 mm pitch (centre) with sheets manufactured out of 0.50 mm this TCT (total coated thickness) high tensile galvalume sheets having tensile strength 550 MPA with 18-20 micron top coat over 5 micron primer and 8-10 micron alkyld backer zinc aluminium alloy AZ-150, sheets having a dip metallic zinc (43.5%0 aluminium (55%) & silicon (1.5%) with total mass coating of 150 gms/sqm on both sides, having wide pans with minimum 3 small stiffening ribs for effective water shedding and special male/female ends with full return legs on laps for purlin support and fixed as per existing profile of roof complete all as specified and directed.

M&L for steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 or RHS/SHS Sections conforming to IS 4923:1997 grade YST 210 complete all as specified and directed. (NOTE: Quoted rates shall be deemed to include for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete. No extra measurement for the same will be considered except for base plates at top & bottom of columns)

M&L for preparing New or previously untreated Steel and Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a Red Oxide Zinc Chrome Primer, complete all as specified and directed.

S&F false ceiling with powder coated exposed G.I. grid suspension system consisting of Main Runner 3600 mm long, Cross Tee 1200mm/600mm long and Wall Angle, wall angle fixed on PVC Dash Fasteners on the perimeter of the wall by steel screws with distance 300 mm c/c, Main Runners placed @ 1200mm, Cross Tee 1200mm inserted in the pre-cut slots of Main Runner at a regular interval of 600 mm to form a modular grid of 1200mm x 600mm and additional cross tees of 600 mm placed perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600mm x 600mm, grid of module size 600mm x 600mm shall be supported by 6 mm dia G.I. wire from purlins/soffit complete all as specified and directed. Note: Ceiling board will measured and paid separately under appropriate item.

S&F 12 mm thick mineral fibre ceiling tiles shall be of dimension 595x595mm with humidity resistance 99% Thermal conductivity K = 0.052-0.057 w/mK colour white, fire performance UK Class 0/Class 1 (BS 476 pt-6&7) suitable for green building application (GRIHA Criteria 17 & 29 SWAGRIHA 12) with recycled content not less than 30 % and light reflectance not less than 85%. NRC of 0.55 to 0.6 duly fixed on GI Snap Grid Frame Work with Steel Screws complete all as specified and directed. Note: Snap grid ceiling frame shall be measured separately under appropriate item.

S&F Chlorinated Polyethylene Chloride (CPVC) pipes 20 mm outside dia, SDR-11, having thermal stability for hot and cold water supply including all SDR-11 CPVC plain and brass threaded fittings (such as Bends, Elbows, Tees, Short Pieces, Connectors, Back - Nuts Caps, Plugs, Unions, Flange (core) & flange (ring), reduction Tee, reducing socket, Male & female threaded socket, tank connector etc) fixed / laying walls, ceilings or in floors etc. with suitable size MS clamp of spacing 1.00 mtr etc pipe line complete all as specified and directed. (NOTE: Quoted rate shall deemed to included for cutting chases in brickwork for concealing pipes)

S&F CPVC Ball valve 20mm (outer dia), screwed both Ends for CPVC pipes, complete all as specified and directed.

S&F vitreous china, white, counter top wash hand basin, rectangular shape, of size 475 x 370mm including providing 32 mm dia chromium plated waste coupling and making all necessary connections complete all as specified and directed. (NOTE: Cost of Waste coupling shall deemed to be included in the quoted rate.)

S&F PTMT bottle trap with internal portion 32mm size and of suitable length as per site requirement for connection to counter top basin complete all as specified and directed.

S&F15mm bore chromium plated single lever central hole basin mixer without popup waste system with 450mm long copper pipe and brass nut, minimum weight 650 grams complete all as specified and directed.

M&L for 18-20mm thick Granite Slab (of any type) work (table rubbed and polished), cut to size required, fixed in walls with MS brackets for installation of counter top basin incl making holes and rounding off edges complete all as specified and directed.

S&F Vitreous China, white, half stall urinal flat back with grating and union for discharge pipe (excluding flush pipe and flushing cistern and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and Union for discharge pipe complete all as specified and directed. (NOTE: Quoted rate shall be deemed to include for the cost of waste coupling and waste pipe)

S&F Self closing angle cock pressmatic for urinal with wall flange and 200 mm connecting pipe duly connected with and including brass chromium plated Urinal spreader complete all as specified and directed.

S&F Corner Glass Shelf single Decker (Triangular shape) of size 30 Cm, complete all as specified and as directed.

S&F Glass Shelf (Bath Tray), 600 mm long alongwith all accessories complete all as specified and directed.

S&F Brass Chromium Plated Tubular Towel Rail, 60 Cm long with Brackets, total weight not less than 300 grams complete all as specified and directed.

S&F PVC Connection Pipe 15mm size and 60 Cm in length with Adapter Nuts of PVC, complete all as specified and directed.

S&F PVC Waste Pipe 32mm bore (dia), 1.0 m length complete all as specified and directed.

S&F angle valve, 15 mm bore, brass, chromium plated fancy type, minimum weight 300 grams, with wall flange fixed to iron pipe complete all as specified and directed.

S&F Chromium plated brass two way Angle valve, fancy type, minimum weight 350 grams, with wall flange fixed to 15 mm bore Iron pipe, complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer composite) solid door/window/ceosetory windows & other frames/chowkhat of size 50 X 75mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibres (wood powder/rice husk/wheat husk) and non-toxic additives (maximum toxicity index of 12 for 100 grams) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N(Edge), minimum compressive strength of 58N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with mild steel hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed. (NOTE: MS hold fast/lugs or SS dash fasteners shall be paid for seperately. For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made)

S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and shall be fixed with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as specified and directed. (Note: Butt hinges shall be paid separately)

S&F Butt hinges, 100 mm long, stainless steel complete all as specified and directed.

S&F Aluminium alloy Handle 125mm long, cast type, anodised, complete all as specified and directed.

S&F Aluminium Barrel Tower Bolt 150mm long (weight not less than 130 Gram), extruded section, complete all as specified and directed.

S&F Steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed.

S&F Frosted Sheet Glass 4.0mm thick, Ordinary Type and glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and directed.

S&F stainless steel Grating Round 100mm Dia with waste hole jointing with Solvent Cement complete all as specified and directed.

S&F PVC Floor Trap 75mm bore (dia) with Grating including jointing to Waste Pipe fixed in Cement Concrete 1:2:4 (20mm graded stone aggregate), complete all as specified and as directed.

S&F PVC (SWR) 75mm bore (dia) Soil, Waste and Ventilating Pipe, Single Socketed, in any length with Rubber Ring Joints, laid on floor, trenches etc complete all as specified and directed.

S&F PVC (SWR) 75mm bore (dia), Bend any type and jointing with Solvent Cement complete all as specified and directed.

M&L for bringing suitable approved earth from outside AF land, breaking of clods and stacking on site for measurement complete all as specified and directed. NOTES :- (1) Earth required for embankment/filling shall be of approved quality and shall be brought from outside the AF land by contractor under his own arrangement. No extra shall be admissible on this account. (2) Quoted rate shall be deemed to included for all labour required for excavation, removing the soil, loading and unloading, transportation to site, making temporary profiles, levelling etc. (3) Density of finished earth in embankment, traverse etc shall be as directed by GE/Engr-in-Charge. (4) Necessary deduction for voids in terms of Para 3.6 on Ser page No 21 of SSR Part-II, 2020 (Rates) shall be carried out from the finished quantity of earthwork. Contractor's quoted rate shall be deemed to be inclusive of the above aspect and no claim shall be entertained at a later date in this regard. (5) Earth shall be procured from outside MOD land only after utilisation of excess earth obtained from excavation items under the subject work.

Excavating in trenches, in soft/loose soil, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out complete all as specified and as directed.

Returning filling including spreading, levelling, watering and well ramming in layers n exc. 25cm complete all as specified and as directed.

Removing excavated material n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

Earth filling under floor, ramp etc including spreading, levelling, watering and well ramming in layers n exc. 25cm thick complete all as specified and as directed.

M&L cement concrete 1:4:8 of type D2 (using 40mm graded stone aggregate) as in filling and mass concrete complete all as specified and as directed.

M&L for RCC design mix (M-25 grade) using 20mm grade aggregate in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete incl properly curing complete all as specified and directed. (NOTE: MS reinforcement shall be measured and paid seperately)

M&L for RCC design mix (M-25 grade) using 20mm grade aggregate in Columns, pillars, piers, posts and struts incl properly curing complete all as specified and directed. (NOTE: Reinforcement shall be measured and paid seperately)

M&L RCC M-25 (Design Mix) in Beams, cantilevers, bressummers, lintels over 1.5m span incl properly curing complete all as specified and as directed. (NOTE: Reinforcement shall be measured and paid separately)

M&L RCC M-25 (Design Mix) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like. incl properly curing complete all as specified and as directed. (NOTE: Reinforcement shall be measured and paid separately)

Supply and laying 250 micron thick HDPE sheet, water proof & wrinkle free without any puncture or damage including minimum overlap of 300mm on edges complete all as specified and directed. (NOTE: Measurement shall be considered for the net area. Quoted rate shall deemed to include for the extra width of overlaps & wasteg. No extra claim shall be admissible during currency of work or afterwards)

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surfaces complete all as specified and directed

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surfaces complete all as specified and directed

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc for rough finished surfaces complete all as specified and directed

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping for rough finished surfaces complete all as specified and directed

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L for TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required as in reinforcement and binding with MS wire (annealed) not less than 0.9mm dia complete all as specified and directed

M&L for brickwork with fly-ash bricks (with old size bricks), straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed

M&L for 15 mm thick plastering in two layers, 10 mm + 5 mm in cement mortar 1:4, top layer of 5 mm thickness mixed with with water proofing compound (as per manufacturer's instructions) on fair faces of brick walls or concrete surfaces finished even and fair (up to any height) for external surfaces complete all as specified and directed. Note : Water Proofing compound shall be measured & paid separately as "Supply only".

Supply only Liquid Water Proofing Compound, conforming to IS code or as approved, complete all as specified.

M&L Rendering 15mm thick in Cement Mortar 1:6 on concrete surfaces, Surfaces finished Even and Smooth without using Extra Cement complete all as specified and as directed.

M&L for preparation of newly plastered surfaces and finished with two coats of exterior acrylic emulsion paint (having anti-dust & anti-algae properties) duly mixed with stainer to achieve approved Tint/shade (in camouflage pattern) over a coat of suitable exterior primer, applied to new wall surfaces of any description, over 10cm width or girth not otherwise described, as per manufacturer's instructions, up to 4 storey height incl necessary scaffolding, safety gear, etc complete all as specified and directed.

S&F Bib Tap 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, Short Body with Capstan Head, minimum weight 400 grams, screwed down, screwed for Iron Pipe or for Brass Ferrule, complete all as specified and directed.

S&F chromium plated Hand shower (health faucet), ABS body with 1.2 metre long flexible tube in chrome finish with wall hook complete all as specified and directed.

M&L for Cement Concrete 1:3:6 type C2 (40mm Graded Stone Aggregate), 75mm thick, as in plinth protection finishing cement concrete surfaces even and smooth without using extra cement complete all as specified and directed.

Dismantling Floor, Paver Tiles, Hearth or Wall Tiling, etc. including Cement Mortar Bedding (but not backing) and removing debris, etc. to Outside MD/AF Land, complete all as specified and directed.

M&L Vitrified Coloured Tiles 9-10mm thick (Square/ Rectangular), Double Charged, Light shade, Polished, area of each Tile not exc. 0.36 Square Metre in Floors, etc. Set in Neat Cement Slurry, laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, tiles fixed with spacers to provide provide a uniform spacing of 3mm between the tiles and after setting of screed bed and tiles, removing the spacers and filling the joints with suitable epoxy grout and pointed with grout complete all as specified and directed. NOTE : Cost of cement screed bed, tile adhesive and epoxy grout shall deemed to be included in the quoted rate.

M&L Vitrified Coloured Tiles 9 to 10mm thick (Square/ Rectangular) Double Charge, Light shade, Polished, area of each Tile not exc. 0.36 Square Metre in Vertical Surface i.e. Dado, Skirting, etc., set and jointed in Neat Cement Slurry and pointed in White or Colour Cement to match the Tiles, laid over and including 10mm thick Screed or Screed Bed in Cement Mortar 1:4, tiles fixed with spacers to provide provide a uniform spacing of 3mm between the tiles and after setting of screed bed and tiles, removing the spacers and filling the joints with suitable epoxy grout and pointed with grout complete all as specified and directed. NOTE : Cost of cement screed bed, tile adhesive and epoxy grout shall deemed to be included in the quoted rate.

M&L for Mild steel framed works such as grills, gratings etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings, framework of water tanks and similar works conforming to Fe-290 Gde E-165 complete all as specified and directed. (NOTE: Quoted rate shall deemed to include for the cost of all GI anchor bolts & nuts, screws, rawl plugs, etc as required for fixing the grills/MS structure to walls or openings. No claim shall be entertained during currency of work.

M&L for Mild steel screw bolts (machine made) with hexagonal or square heads at one end & screwed the other or screwed both ends each screwed end to be fitted with washers & one hexagonal or square nut, exc 5 cm but n exc 10 cm long, diameter 5 to 10 mm complete all as specified and directed.

SCHEDULE 'A' PART-II (ELECTRIFICATION WORKS)

M&L Point Wiring (concealed) with 1.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn through and including Rigid Non-metallic PVC Conduit 20mm in size, medium grade, ISI marked and its Accessories in Concealed (Partly)/Surface (Partly) with necessary grouting of required size and depth on Wall and Making Good in Cement Mortar 1:3, providing Sunk Mild Steel Pressed GI Terminal Box (1.2mm thick) of suitable size (as required) and cover plate and frame for mounting MODULAR TYPE Switches, Sockets, Fan Regulators, etc. and Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/FAN POINT/BELL POINT CONTROLLED BY ONE 1-WAY SWITCH 6 AMP incl finishing good disturbed surfaces complete all as specified and as directed. CONTD......

(NOTES TO ITEM NO 2.01) :- (i) Where tube light fitting is to be fitted/ suspended, CI Circular boxes shall be provided with the PVC Pipes in the ceiling & the unit rate shall be deemed to be included for the same. (ii) Quoted rate shall be deemed to be inclusive of the cost of terminal box. Modular cover plate & frame shall be measured and paid seperately (iii) Cost of cutting chases for concealed wiring and making good surfaces with cement plaster and putty shall be deemed to be inclusive in the quoted rates. No claim shall be admissible at a later stage)

S&F Modular Switch 1 way 6 A, 1 module complete all as specified and as directed.

S&F Ceiling rose, surface type, three terminals complete all as specified and directed

S&F exhaust fan 300 mm sweep, 1300 RPM, heavy duty, AC Single Phase 230/240 volts, metal body, with louvers complete with all accessories and connecting up with and including twin core twisted flexible copper conductor cable of size 1.5 sqmm (nominal area) from ceiling rose to fan complete all as specified and directed. (MAKE : HAVELLS, Model: Ventil Air DS / CROMPTON, Model: Transair / USHA, Model: Aero Clean Plus or equivalent model in BAJAJ / ALMONARD / ORIENT) (NOTE : Hole shall be left in brickwork during bldg construction stage and shall be finished properly with cement plaster.

S&F surface mounted LED luminaire, 1 X 20 Watt in aluminium housing, 100 lumen/watt, operating voltage 180-270 V, with acrylic/polycarbonate difuser & integrated constant current electronic driver complete with all other accessories internally prewired and including connecting up with three core flexible copper wire of suitable size complete all as specified and directed.

M&L for concealed sub main wiring with 2 run of FRLS-H PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm alongwith one run of FRLS-H PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm as earth continuity conductor drawn through and including PVC conduit (medium grade) of suitable size, including taking down of old Submain wiring any type including batten/ conduit/casing at any indicated situation complete all as specified and directed. (NOTE : (1) Three runs of single core 4.0 sqmm cable & one run of PVC conduit shall be measured as one unit. (2) Cost of cutting chases for concealed wiring shall be deemed to be inclusive in the quoted rates. No claim in this regard shall be entertained at a later stage. (3) On completion of the wiring work, the contractor shall fill and finish the chases with cement mortar 1:6 and finsihed flush with the adjacent surfaces. Rate quoted by the contractor shall be deemed to include for the above aspect and no claim shall be entertained at a later stage.

S&F SPN DB, IP 43 protection, double door, 240 volts, 4 way, with 100 Amps copper Bus Bar complete all as specified and directed. NOTE: Incoming and outgoing MCBs shall be measured and paid seperately.

S&F MCB, 'B' Curve, SPN, 40-63 Amps, breaking capacity 10KA complete all as specified and directed.

S&F MCB, 'B' Curve, single pole, 6 to 32 Amps, breaking capacity 10KA complete all as specified and directed.

S&F in repairs LED Flameproof Flood Light fitting, 120 watt capacity, CMRI & PESO Certified with high powered LED in SMD arrangement, in high pressure die cast aluminium housing, epoxy powder coated finish with prismatic polycarbonate modular secondary lens optics with integrated constant current electronic driver and heat resistant clear Type-A toughened glass cover, cable entry M20 (02 Nos) with gland & plug, IP66 grade ingress protection suitable for operating voltage 140V-270V AC, 50 Hz complete all as specified and directed and complying with the following specifications:-. (a) system efficacy more than 100 lumen/watt (b) CRI > 80, (c) THD < 10% (d) Power factor not less than 0.95 (e) having 10 KV surge protection (f) colour temperature between 6000-6500 degree K

S&F LED Flood Light fitting, 70 Watts capacity, in high pressure die cast aluminium housing with prismatic polycarbonate modular secondary lens optics with integrated constant current electronic driver and toughened glass cover, IP66 grade ingress protection, impact resistance IK07 complete all as specified and directed and complying with the following specifications:-. (a) minimum system efficacy 120 lumen/watt (b) CRI not less than 70, (c) THD < 10% (d) Power factor not less than 0.90 (e) having in built short circuit and surge protection upto 4 kV (f) colour temperature not less than 5700 degree K (g) life not less than 50000 hours of operation

Supplying and fixing 1100 volts grade heavy duty cable, PVC insulated aluminium stranded conductor, served with inner sheathing of PVC tape and overall PVC sheathed, one three core cable flat or circular with stranded aluminium conductor of size 10 Sqmm complete all as specified and directed.

S&F in repairs Switch, Flame Proof Rotary type with Termination Box in LM6, 16 Amp, Single Pole, 250 Volts, complete all as specified and as directed.

S&F in repairs Flame Proof & Weather Proof Switch Socket with Plug Combined in LM6, Termination Box in LM6, 16 Amp, 250 Volt, 2 Pin and Earth Plug, Fully Interlocked suitable for installation in hazardous as per IS-2147/62 Alluminium alloy/Cast Iron Neoprene Gasket Degree of Protection IP 65 and and Certified CIMFR DHANBAD & CCOE NAGPUR, BS with ISI marked and complete all as specified and as directed.

S&F in repairs Flame Proof & Weather Proof Switch Socket with Plug Combined in LM6, Termination Box in LM6, 25 Amp, 415 Volt, TPN, 3 Pin and Earth Plug, Fully interlocked suitable for installation in hazardous as per IS-2147/ 62 Alluminium alloy/Cast Iron Neoprene Gasket Degree of Protection IP 65 and Certified CIMFR DHANBAD & CCOE NAGPUR, BS with ISI marked and complete all as specified and as directed.

Taking down/out unserviceable Wires only from the existing Sub-main Wiring of any type and any description, without disturbing Existing Conduit, complete all as specified and directed.

S&F Flame Proof Sub-main Wiring with 2-Runs of 4.0 Sqmm (nominal area) 1100 Volt, PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable and 1-Run of 4.0 Sqmm (nominal area) 1100 Volt, PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuty Cable along with the Wiring drawn in existing ERW/GI CONDUIT complete all as specified and directed. (NOTE: Three runs of single core 4.0 sqmm wire shall be measured as one unit. Conduit, if replaced, shall be measured and paid seperately)

S&F PVC electrical conduit, 25 mm dia, MMS type, medium grade incl all fittings and accessories complete all as specified and directed.

S&F Weather proof & flame proof TPN DB, 8 way, in cast alumnium alloy LM6 construction, provided with appropriate neutral & earth link bar (approved by CIMFR DHANBAD & CCOE NAGPUR) and Elecrically Connecting up & testing complete all as specified and as directed and provided with the follwoing accessories :- (i) Incomer MCB, 63 Amps, 4 Pole, 10 kA - 01 No (ii) Outgoing MCB, SP, 6-32 Amps, 240 Volt, AC, 'C' Series, 10 kA - 24 Nos NOTE: Quoted rate shall be deemed to be inclusive of the cost of MCBs.

S&F Weather proof & flame proof SPN DB, 8 Way, in cast alumnium alloy LM6 construction, provided with 100 Amps neutral & earth link bar (approved by CIMFR DHANBAD & CCOE NAGPUR) and Elecrically Connecting up & testing complete all as specified and as directed and provided with the follwoing accessories :- (i) Incomer MCB, SPN, 32 Amps, 240 Volt, AC, 'C' Series, 10 kA - 01 No (iii) Outgoing MCB, SP, 6-32 Amps, 240 Volt, AC, 'C' Series, 10 kA - 06 No NOTE: Quoted rate shall be deemed to be inclusive of the cost of MCBs.

S&F Air Termination Single Pointed Copper Rod 12mm dia and 300mm long with suitable Arrester Clamp made out of Brass/Gun Metal including provision of Cement Concrete 1:2:4 (20mm graded stone aggregate) Block 300x300x300mm, complete all as specified and directed.

S&F Galvanised Iron Strip 32x6mm with Saddles and fixing Screws for Roof/Earth Conductors and Down Conductors, complete all as specified and as directed. NOTE: Cost of Screws, Saddles, Insulators, Nuts and Bolts, etc. shall be deemed to be included in Quoted Rate.

S&F Test Point Terminal Block made of Gun Metal or Phosphorus Bronze size 75x75x25mm, drilled and screwed including 3 No. 8mm dia, 25mm long hexagonal Head Screw, complete all as per specified and as directed.

S&F Galvanised Iron Tubing/Pipe 40mm bore (dia), light grade for Strip Protection, fixed in Walls/Floors with suitable type of Clamps, etc., complete all as specified and as directed.

M&L for Providing, cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in blocks etc for fixing bases of air termination rods, GI pipes etc, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.5M below normal ground level connected to galvanized steel earth strip 25x4mm (up to 7.5 metres) by means of bolts, nuts check nuts and washers of galvanized steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 45 cm x 45 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm centre to centre both ways, with one handle for lifting made out of 8 mm dia MS bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 40 mm bore galvanized steel tubing medium grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown in Figure 15A of IS 3043 :1987, complete all as specified and directed.

M/s Satguru Traders (BID ID -3415441)

M/S Aggarwal construction co. (BID ID -3418616)

Ajay Enterprises (BID ID -3415501)

M/s Har Nandi Construction Company (BID ID -3415642)