SPECIAL REPAIR OF BLDG NO ET-55A (OR COOK HOUSE) AT MH PACHMARHI (MP) UNDER AGE (I) PACHMARHI

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing and disposal of rubbish off Premises complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular), area of each tile exc 0.11 sqm but not exceeding 0.18 sqm, in floors etc, laid over and including 15mm thick screed bed in CM(1:6), set & jointed in neat cement slurry and pointed with white or coloured cement to match with the shade of tiles complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 350x250x7/450x300x7mm thick in vertical surfaces such as skirting/dados/wall, laid over and including 10mm thick screed bed in CM(1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

Dismantling brick work built in cement mortar including all quions, arches, pillars, etc complete all as specified and directed.

M&L Brick work with sub class 'B' fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed.

M&L 25 mm thick cement concrete (1:2:4), type B-0, using 12.50 mm graded crushed stone aggregate as in floors including finishing the surface rough & even without using extra cement complete all as specified and directed.

M&L 50 mm thick PCC 1:2:4 type B-1 using 20mm graded aggregate as in plinth protection, finishing even & fair without using extra cement, laid in bays with construction joint, 6mm thick, joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 80/100 gde and three part of sand ( all by weight) complete all as specified and directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded and pointed in any mortar complete all as specified and directed.

M&L Machine cut Kota stone slab flooring, 20-25mm thick, as in flooring over and including cement mortar in CM(1:6), laid and jointed with grey cement slurry mixed with pigment to match with the shade of the slab including rubbing, polishing complete all as specified and directed.

Taking down cement plaster on wall/ceiling/roof etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L 15 mm thick rendering on fair faces of brick/concrete ( internal) surfaces in CM (1:6), finished even and smooth (without using extra cement ) complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:4, in two layers (1st layer 10 mm thick rendering coat and 2nd layer 5 mm thick finishing coat) on brick work or concrete external surfaces, second layer (finishing coat) mixed with liquid water proofing compound @ 200 ml / 50 Kg bag of cement as per manufacturer's instructions and finished the surfaces even and fair without using extra cement complete all as specified and directed. (Note : Liquid WPC will be measured and paid for separately as " Supply only".)

Supply only liquid water proofing compound , ISI marked, complete all as specified and as directed.

Taking down chowkhats or frame with shutters of any description (without taking off shutters from the frames) n. exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkhats or frame with shutters of any description (without taking off shutters from the frames) exc 1.5 Sqm but n exc 4 sqm each complete all as specified and directed.

Taking down shutter of any description exc 1 sqm but not exc 2 sqm each complete all as specified and directed.

Dismantling timber scantlings as in framed work, 40 sq. cm and over in section, in any position, complete all as specified and directed.

Cutting holes in brick walls exc 1/2 brick & n exc full brick built in cement mortar for inserting hold fasts, cutting and preparation of brick wall for insertion of doors, windows & ventilator and making good dismantled portion in cement mortar 1:3 etc complete all as specified and directed. (Note : This item is to be executed for fixing of door and window frames at new locations.)

S & F factory made 35 mm thick 2nd class hardwood (Indian Sal, Bijasal, Hollock or Benteak), glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc fitted to chowkhats for doors etc complete all as specified and directed. ( Note : Wire cloth shall be measured and paid for separately)

S&F anodised aluminium frame with powder coating (minimum thickness of powder coating 50 micron) for doors, window, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including glass and stainless steel wiremesh,powder coating not less than 50 micron thick, necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinges type B-21 100mm long (2 no.) and suitable handle (1 no.) complete all as specified and directed.

S & F factory made 35 mm thick plain, framed, panelled shutters (Two panels) with lock rail and panel of 9 mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces and size of the members of shutter as per IS – 1003 (Part – I), made of kiln seasoned & chemically pressure treated 2nd class hardwood (Indian Sal, Bijasal, Hollock or Benteak) rail and style complete all as specified and directed.

S & F 30 mm thick flush shutters solid core construction with block board core and plywood face panels, commercial type on both sides, supplied and fitted to chowkats, complete all as specified and directed.

S&F Mild steel framed works such as grills,gratings,etc, with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work for portions framed and hung as gates, including pintle hinges, stops, hand made sliding bolts, etc conforming to Fe - 290 Gde -E-165 complete all as specified and directed.

S&F pressed steel frame size (105 x 60 mm) 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

S&F pressed steel frame size (165 x 60 mm) 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

S & F solid PVC door frame of size 50 mm x 47 mm, made out of 5 mm plain colour PVC sheet reinforced with M.S square tube, supplying & fixing in opening complete as per specified in drawing in SSR Part II(2020) and as directed.

S&F Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing in SSR Part-II(2020) and as directed.

S&F 100 mm size Butt hinges, extruded Stainless Steel with steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S&F 75 mm size Butt hinges, extruded Stainless Steel with steel hinge pin, anodised and fixed, type C-22 complete all as specified and directed.

S&F Butt hinges (ISI marked), medium weight, cold rolled mild steel, of size 100 mm complete all as specified and directed.

S&F 200 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm Aluminium anodised, barrel tower bolts of extruded section all as specified and directed.

S&F 150 mm extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed.

S&F Stainless Steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple/ wooden beads complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter, & kitchen cupboard shutters with particle board core 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing in SSR Part-II(2020) complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 15 mm bore GI tubing complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 20 mm bore GI tubing complete all as specified and directed.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 15 mm bore GI tubing complete all as specified and directed.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 20 mm bore GI tubing complete all as specified and directed.

S&F in repair bib tap 15 mm bore fancy type, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair CP brass tubular towel rail 20 mm dia 'D' type, 60 cm long between flanges complete all as specified and directed.

S&F in repair angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe complete all as specified and directed.

S&F, in repair, stainless steel soap dish, of standard size and shape complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1 mm thick, in kitchen with plugs, washers and waste coupling , & waste pipe including bedding in cement mortar to dwarf wall or including fixing suitable sizes of cantilever brackets and connecting union to pipe, overall size 915 x 460 mm, bowl size 410 x 330 x 160 mm complete all as specified and directed.

M&L for 18 mm thick granite slab (of any type) work (table rubbed and polished) in cooking platforms, steps, window cills, including edge moulding & cutting holes for gas pipe through drill machine and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M&L Machine cut cudappah stone slab flooring, 20-25mm thick, over and including 20mm thick cement screed base in CM(1:4), laid and jointed with grey cement slurry mixed with pigment to match with the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for makrana white marble work, 18 to 20mm thick, (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, borders/mofits and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with the shade of marble complete all as specified and directed.

Taking down AC/PVC pipes (including all fittings), with spigot and socket ends and lead joints including burning out joints of 100 mm dia pipe complete all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed, in any length, with rubber ring joints, laid in floors or in trenches complete all as specified and directed.

S&F PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints laid in floors or in trenches complete all as specified and directed.

S&F stack clamp made out of 50x5 mm flat iron and 16mm dia round iron stays, including bolts & nuts and securing ends of stays to wall or roof for 110mm PVC pipe complete all as specified and directed.

M&L PVC(SWR) bend of 110mm dia of any radius etc complete all as specified and directed.

M&L PVC(SWR) Tee of 110mm dia etc complete all as specified and directed.

S&F PVC (SWR) multi floor trap, plain with grating with or without waste hole including jointing with solvent cement, 75mm dia, complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of primer complete all as specified and directed.

M & L for preparation of new steel surfaces any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red-oxide primer complete all as specified and directed.

M&L Preparing old wooden surfaces exceeding 10Cm in width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L Preparing old steel surfaces exceeding 10Cm in width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M & L for preparation of newly plastered surfaces of wall & concrete and applying 2 mm thick wall care putty including preparation complete all as specified and directed.

M&L for applying two coats of oil bound distemper on wall or concrete over a coat of primer on prepared surfaces including, rubbing with sand paper complete all as specified and directed.

M&L for preparation of old decorated plastered or unplastered surfaces of wall by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coat of white wash complete all as specified and directed.

M&L preparation of new plastered or unplastered surfaces of wall and applying two coats of cement based paint over a coat of appropriate primer complete all as specified and directed.

S&F for MS framed works conforming to Fe-410 Gde E- 250, Quality 'A', as in purlin, rafters, column (square/rectangular, round) or angle section, fixed with and including iron cleats or other connected plates, flat iron wind ties etc including bending of MS section complete all as requried and as directed.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

M&L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick(AZ-150) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, including ridge of same colour fixed with self tapping screws complete all as specified and directed.

M&L pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick(AZ-150) as in ridge,hip,valley of any colour having tensile strength of 550 Mpa as in ridge, fixed with self tapping screws complete all as specified and directed.

Dismantling ceiling board with fittings, any thickness and of any description including cover fillets complete all as specified and directed.

M&L for false ceiling (at any height), 600x600x15mm mineral fibre ceiling tiles micro looks edge laid on super fine XL 15mm exposed grid systems with 15mm wide T-section flanges. The frame work comprises of main runner of size 15x32x3000mm spaced at 1200mm centre to centre, securing, fixed to the structural soffits by approved hangers at 1200mm C/C (maximum) , Hangers (GI wire of 4.0 mm dia) to be fixed by approved roof plug, level adjusters and screws etc. The last hanger at the end of each main runner should not be greater than 450mm from the adjacent wall flush fitting 1200mm long cross tees of size 15x26x1200mm, to be interlocked between main runners at 600mm C/C, to form a 1200mmx600mm module, cut cross tees longer than that 600mm to be supported independently 600mmx600mm modules, to be formed by fitting 600mm long flush fitting cross tees of size 15x26x600mm centrally between the 1200mm cross tees perimeter wall angle of size 19x19x3000mm secured to wall at 450mm C/C (maximum), Finally mineral fibre tile 15mm thick micro look edge has to be laid on the 600mmx 600mm module complete all as specified and directed.

Taking down existing unserviceable/old point wiring surface /batten including fitting fixtures ,ceiling roses, pendant/angle holders, regulators, sockets,switches , PVC conduit complete all as specified and directed.

M & L for point re-wiring with 1100 volts grade PVC insulated FR-LSH multistranded copper conductor cable 1.5 sqmm (Phase-Red, Netural-Black) and earth continuity conductor 1.5 Sqmm (Green) drawn into and including PVC casing-caping not less than 32 x12mm ISI marked ivory colour with all fittings/ fixing accessories and sunken galvanised pressed steel terminal boxes of thickness not less than 1.2mm including covering with moulder plate and frame white for mounting switches, sockets, fan regulators as required for the followings :-

(a) One light/fan/exhaust fan point point controlled by 1 No,one way 5/6 Amp switch.

(b) One 3 pin /5 pin socket outlet 5 Amp controlled by 1 No one way 5/6 Amp switch on same board along with other switches ,fan regulator etc.

(c) One 3 pin /5 pin socket outlet 5 Amp controlled by 1 No one way 5/6 Amp switch on independent board.

M & L for point re-wiring with 1100 volts grade PVC insulated FR-LSH multistranded copper conductor cable 2.5 sqmm (Phase-Red, Netural-Black) and earth continuity conductor 2.5 Sqmm (Green) drawn into and including PVC casing-caping not less than 32 x12mm ISI marked ivory colour with all fittings/ fixing accessories and sunken galvanised pressed steel terminal boxes of thickness not less than 2mm including painting terminal boxs inside and outside with two coat of synthetic enamel paint over one coat of red oxide primer with top cover 3 mm thick bakelight laminated sheet with brass screws and Cup washer with all assessories complete all as specified and directed.

S&F switch piano flush button single pole one way 6 Amp, 240 Volts conforming to IS 3854 ISI marked complete all as specified and directed.

S&F for socket outlet, 3 Pin, 5 Amp flush type conforming to IS 1293 ISI marked complete all as specified and directed.

S & F ceiling rose, surface Bakelite,isolated body three terminals complete all as specified and directed.

S&F angle holder, insulated polycabonate body with back plate complete all as specified and directed.

S&F switch piano flush button single pole one way 15 Amp, 240 Volts conforming to IS 3854 ISI marked complete all as specified and directed.

S&F for socket outlet, 5 Pin, 5 & 15 Amp flush type conforming to IS 1293 ISI marked complete all as specified and directed.

S & F 4 Way Novello vertical TPN distribution boards, Double Door, 415 V, 50 Hz, protection class IP43 As per IS 8623 - III, Impact resistance IK09 ,Provision for mounting Earth ,Leakage Relay, SVN Indications & MCCB RCD block way, MCCB+12 modules including taking out old unserviceable one complete all as specified and as directed.

S&F sheet metal enclosure (MCB Distribution board) when MCB’s to be used, single pole and neutral, 8 ways, 230 Volt with 200 Amps rated bus bar, double door with bus bar neutral link, earth bar, Din rail, necessary blanking plate, including fixing DB flush in wall complete and making good disturbed surfaces as per existing specifications complete all as specified and directed .

Taking down existing old unserviceable submain wiring surface /batten including PVC conduit complete all as specified and directed.

S & F sub main wiring using approved colour coding (Phase-red,Neutral-black,Earth-green) complete with two single core FRLS PVC insulated and unshealthed stranded copper conductor cable 6 sqmm as current carrying conductor and one run of 6.0 sqmm as earth contunity conductor ,voltage rating 1100 volt ,ISI marked drawn in and including concealed PVC conduit ISI marked of dia not less than 25 mm and thickness 2 mm with stranded accessories complete all as specified and directed. (Note: Two run of single core FRLS PVC cable with one run of earth contunity conductor and conduit shall be measured as one unit.)

S&F MCB, single pole, 6 Amp to 30 Amp, 240 Volts, ''B'' series, 10 KA , complete all as specified and as directed.

S&F MCB, single pole and neutal, 32 Amp to 40 Amp, 240 Volts, ''B'' series, 10 KA , complete all as specified and as directed.

Supply and fix MCCB,4 Pole, 12 to 63 Amp, 50 Hz, 415 V with rupturing capacity 25 KA complete all as specified and directed.

Supplying,installation and testing electric geyser (water storage type) of 25 litres capacity, vertical mounting type, glass lined inner tank, rust proof outer body, 2 KW heating element, suitable for 230V single phase 50 Hz AC supply, BEE Five star Rated, energy efficient, 8kg per sqcm presure withstanding capacity, Class I, ISI Marked, with and including Thermostat with thermal output, heating indicator, multi-functional valve(acts as pressure release valve, non-return valve, expansion valve and vacuum release valve), fixed all as per Manufacturer's instructions, fixed with and including Anchor type/fastener type bolts and nuts(set of 4 bolts of 10mm dia 150 mm long with nuts and washers) into the wall grouted properly to hold the geyser and making good the disturbed surface complete all as specified and as directed

Supply and fix Industrial plug and socket 32 A complete all as specified and directed.

Supply & fix LED tube light along with fixture,18 W complete all as specified and directed.

S & F for Highly efficient LED Bulbs, 10 W, used as a ready replacement for existing GLS/CFL direct fit lamp,in B-22 , complete all as specified and directed.

M&L for earthing complete with galvansided steel earth plate electrode 600x600x6.0mm thick directly burried in the ground (earth pit not less than 2.25M deep below ground level) with top edge of earth plate not less than 1.50M deep below normal ground level, connected to galvanised iron wire 4mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel, 15mm bore GI pipe medium grade including necessary fittings for protection of earthing wire, watering pipe 20mm bore GI medium grade, concrete chamber in PCC (1:4:8) type D-2 using 40 mm grade aggregate, coping shall be in PCC (1:3:6) type C-1 using 20 mm grade aggregate and internal surfaces of concrete chamber shall be given 12mm thick plaster in CM (1:4), funnel with wire gauge of 22 gauge (0.63 mm) 8 mesh per linear including 50mm thick cover of RCC (1:2:4) type B-1 using 20mm grade stone aggregate reinforced with 8mm MS deformed bar @ 75 mm C/C both ways, char coal dust and common salt all as shown in electrical plate No. 3 of SSR Part-I (2009) including all necessary excavation & earth work and removal of surplus soil to a distance n. exc 50M and providing connection points with MS/ GI bolts & washers as required and connection from earth test point to earth electrode with same GI earth wire alongwith protection pipe and testing on completion complete all as specified and directed. Note:- GI wire and protection pipe from earth electrode to test point max upto 7.50M shall be deemed to be included in the unit rates as quoted by the contractor.

Supply and fix Single phase propeller type Exhaust fan heavy duty AC 230 volts 300 mm sweep, metallic body complete with Metalic louvrers and shutters including electric connection with PVC flexible twin core copper wire from ceiling rose to Exhaust fan, nut & bolt complete all as specified and as directed.

Supply and lay pipe galvanized, “Medium grade”, including fittings 15 mm bore all as specified and directed.

S & F 15mm bore Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and directed.

S & F stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed of size 15 mm bore all as specified and directed.

Supply and fix, Single phase, ceiling fan 1200 mm sweep, permanent magnet Brushless Direct Current(BLDC) Motor 230 Volt, 50 Hz, 5 Star rated , 26-30 Watt, rated current 0.16 amp, pf 0.98, 370/360 rpm, minimum air delivery 210 CFM with service value greater than 6.00 BEE, number of blades three, type of blade leaf 1.05 mm thick aluminium sheet, remote control, radio frequency, 5 speed +off timer option speed regulation, class of insulation 'B' with two nos bearings including connecting wire from ceiling rose to fan terminal complete with all as required and directed at site by Engr -in charge

Supply and fixing building Security light LED 35 W complete all as specified and directed.

Supply and laying or fixing or passing in trenches/ on pole/ through pipes, 1100 volts grade XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, heavy duty electric cable with stranded aluminium conductor of cross section area 35sqmm, 3.5 core including jointing materials such as cable glands & lugs etc complete all as specified and directed.

M & L excavation for taking out/laying cable in trenches in soft/loose soil not exc 1.5 m wide and not exceding 1.5 m deep for LT 1100 V under ground cable complete all as specified and directed.

Returning filling in including spreading, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Removing surplus spoil to distance not exceeding 50 M and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Supply and spreading clean and dry fine sand free from sharp materials (unwashed) laying in trenches around the cable for cushioning in trenches, laid to a uniform thickness of 23cm (15cm under the cable & 8cm over the cable) and gently punned down to 18cm thickness complete all as specified and as directed. ( Note : Punned thickness shall be considered for payment purpose.)

Supply and laying unreinforced precast concrete cable cover, Class LV, Type 1, flat, size 250 mm x 150 mm x 40 mm complete all as dpecified and as directed.

Schedule of credit amount of Rs. 48178.00 to be deducted during AOC

DEEPAK JAISWAL

Dev Enterprises

GHASI RAM SAHU

SUBIR KUMAR ROY