Proposed Extension of Ring Rolling Inspection Hanger Building on Both Sides Including Civil, Electrical Works at Foundry Forge Division, HALBC.

HINDUSTAN AERONAUTICS LIMITED BANGALORE FACILITIES MANAGEMENT DIVISION

NAME OF THE WORK: Proposed Extension of Ring Rolling inspection hangar building on both sides including Civil,Electrical works at Foundry & Forge Division, HAL (BC). CONTRACT NO. HAL/FMD/C-50A/24-25

Name of the Contractor :

Sl. No. Specification Quantity Unit Rate in Figs [Excluding GST] Rate in Words Amount

Preamble: (1) The subject work has been called on works contract basis and prevailing GST for same is 18%. Any change in GST +/- during the currency of contract shall be on HAL account. The Tenderer shall abide by prevailing GST act. (2) L1 (lowest quote) will be determined based on the total quoted amount including GST. (3)This BOQ specification has to be read in conjunction with relevant CPWD specifications amended upto date/ detailed technical specification in tender document and tender drawings if any.

Part 'A' - Civil Works

1 Disposal of surplus earth/moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material of partitions,ceiling boards,tiles,frames etc by mechanical transport including loading, transporting, unloading in all lifts/loads upt 10 km distance from HAL. completely as per directions of Engineer-in-charge. 30.00 Cum 453.94 Rupees Four Hundred Fifty Three and Ninety Four Paise Only 13618.20

2 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas in all kinds of soft / hard soil for foundations, footings, column pedestals or members as per the drawing etc.,including removal of vegetation and in-equalities, shoring, strutting for protecting the sides of foundation if required, removing slips or falls in excavation, forming steps in sides of deep excavations and their removal or covering up, levelling, ramming the bottom of excavation, getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m with all labour, tools & tackles, plant & machinery, hire & fuel charges etc.,all complete as directed by Engineer-incharge. 30.00 Cu m 163.08 Rupees One Hundred Sixty Three and Eight Paise Only 4892.40

3 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation,trenches or drains, pipes, cables etc. in all kinds of soils (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lifts, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m with all labour, tools & tackles, plant & machinery, hire & fuel charges etc., all complete as directed by Engineer-incharge. 20.00 Cu m 239.14 Rupees Two Hundred Thirty Nine and Fourteen Paise Only 4782.80

4 Returning / filling in with useful excavated soil (excluding rock), free from salts, organic or other deleterious matter (Other than black cotton soil & rock etc., in trenches, plinth,sides of foundations etc., spreading in layers not exceeding 20 cm thick, watering, breaking / removing clods exceeding 50 mm, ramming and consolidation of each deposited layer etc., with all labour, tools & tackles, plant & machinery, etc., lead upto 50 m and for all lifts, all complete as directed by the Engineer-in-Charge. 15.00 Cu m 180.07 Rupees One Hundred Eighty and Seven Paise Only 2701.05

5 Supplying, mixing and placing plain cement concrete (1:4:8) (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate) of required thickness using 40 mm down graded hard stone/granite aggregate in accordance with IS 456 in foundations, mass concrete, sub bases and other similar works including formwork, mechanical mixing, transporting, vibrating, consolidation, levelling, curing, dewatering if any, all materials, labour, lead & lift, tools, plant & machinery, keeping concrete well wetted during the curing period and protecting it in extreme weather conditions etc., but excluding the cost of centering, shuttering and finishing, all complete as directed by the Engineer-in-Charge. 20.00 Cu m 6258.38 Rupees Six Thousand Two Hundred Fifty Eight and Thirty Eight Paise Only 125167.60

6 Supplying, mixing and placing plain cement concrete (1:2:4) (1 Cement : 2 coarse sand derived from natural sources : 4 graded stone aggregate) of required thickness using 20 mm nominal size down graded hard stone/granite aggregate in accordance with IS 456 in posts, struts, buttresses, string or lacing courses,parapets, coping, bed blocks, anchor blocks, plain window sills, fillets,sunken floor etc including formwork, mechanical mixing, transporting, vibrating, consolidation, levelling, curing, dewatering if any, all materials, labour, lead & lift, tools, plant & machinery, keeping concrete well wetted during the curing period and protecting it in extreme weather conditions etc., all complete as directed by the Engineer-in-Charge. 5.00 Cu m 9091.01 Rupees Nine Thousand Ninety One and One Paise Only 45455.05

7 Supplying, straightening, fabricating (cutting & bending), placing in position and binding steel reinforcement of TMT bars of not less than Fe 500 D conforming to IS 1786 for all concrete reinforcment members / works above/below plinth level, including cutting to length, bending to shape required, including cranking, bending spirally for hooping for column, hooking ends and binding with mild steel wire (Annealed) not less than 0.9 mm dia or securing with clips, including fixing and bracing, wastage, welding, supporting or otherwise holding firmly in position so that the placing and ramming of concrete will not displace it etc., complete all as per specifications, drawings and as directed by the Engineer-in-Charge. Note: Only authorized laps, chairs etc. shall be considered for measurement. 12000.00 Kgs 99.08 Rupees Ninety Nine and Eight Paise Only 1188960.00

8 Providing and laying in position ready mixed or site batched M25 Grade with minimum cement content of 330 kg/m3 design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, PortlandPozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, consolidation, levelling, curing, scaffolding, all materials, labour, carriage for all leads & lifts; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge. Note: Mix design to be obtained from Govt. / NABL laboratory for site batching concrete.

a) All works upto plinth level like footing, pedetsal, piles, plinth beam including necessary openings and packing if any for laying pipes, cables etc. 50.00 Cum 8732.29 Rupees Eight Thousand Seven Hundred Thirty Two and Twenty Nine Paise Only 436614.50

b) All works above plinth level like column, beams, slabs, canopy, chajja, stairscase etc. level including necessary openings and packing if any for laying pipes, cables etc. 40.00 Cum 9059.03 Rupees Nine Thousand Fifty Nine and Three Paise Only 362361.20

9 Formwork by providing timber, wooden planks, runners / M.S. sheets with all supports, struts, braces, wedges, scaffolds, bracings, ladders, gangways, dressing with oil including M.S. bolts nuts and washers, temporary openings, filleting for a stop, chamfered edges, internal / external splayed, rounded angles or grooves for forming throating including making temporary openings in the forms for pouring concrete etc as per drawing., all complete as directed by the Engineer-in-Charge Note: Formwork material is contractor's own property and shall be removed after completion of work.

a) Foundations, footings, bases of columns/pedestal,for mass concrete etc. 210.00 Sqm 360.28 Rupees Three Hundred Sixty and Twenty Eight Paise Only 75658.80

b) For Slabs/Balconies/Landings. 50.00 Sqm 851.89 Rupees Eight Hundred Fifty One and Eighty Nine Paise Only 42594.50

c) For Lintels, Beams, Plinth Beams. 345.00 Sqm 676.55 Rupees Six Hundred Seventy Six and Fifty Five Paise Only 233409.75

d) For columns 30.00 Sqm 883.18 Rupees Eight Hundred Eighty Three and Eighteen Paise Only 26495.40

10 Providing and fixing expanded metal mesh of size 20x60 mm and strands 3.25 mm wide 1.6 mm thick weighing 3.64 kg per sqm for encasing of rolled steel sections in beams, columns and grillages, excluding cost of hangers.All complete as directed by the Engineer-in-Charge. 30.00 Sqm 445.63 Rupees Four Hundred Forty Five and Sixty Three Paise Only 13368.90

11 Supplying and laying Brick work with common burnt clay machine moulded modular bricks of class designation 7.5 for walls,chambers,ducts,drains etc awith CM(1:6) t all levels & heights including hoisting and setting in position and along with necessary formwork, curing, finishing, making or leaving holes & chases and making making horizontal and vertical grooves 10 mm wide 12 mm deep before plastering all complete as directed by the Engineer-in-Charge. 160.00 Cu m 8365.90 Rupees Eight Thousand Three Hundred Sixty Five and Ninety Paise Only 1338544.00

12 Supply and Construction of Sized stone masonary works with CM(1:6) in foundation and plinth by placing the stones in layers ,packing,leveling,curing and finishing the joint ,all complete as per the Instruction of Engineer-in-Charge. 17.00 Cum 8095.88 Rupees Eight Thousand Ninety Five and Eighty Eight Paise Only 137662.34

13 Providing and fixing Second Class Teak wood for frames of doors, windows, hand rails, frame work for partitions in etc cut to shape and required curvature and preparing the surfaces to receive the polishing fixed in position with hold fast lugs/with dash fasteners of required dia & length/SS Screws at all heights,with necessary moisture content test.complete as per direction of Engineer-in-charge. (Fastners/hold fasts/SS Screws to be paid separately) 0.05 Cum 131332.01 Rupees One Lakh Thirty One Thousand Three Hundred Thirty Two and One Paise Only 6566.60

14 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).complete as per direction of Engineer-in-charge. 4.00 Each 210.25 Rupees Two Hundred Ten and Twenty Five Paise Only 841.00

15 Providing and fixing 35mm thick flush door shutters conforming to IS :2202 (Part I) non-decorative type of approved brand/make, core of block board construction with frame of 1st class hard wood & lipping with 2nd class teak wood battens 25 mm minimum depth on all edges and well matched commercial 3ply veneering with vertical grains or cross bands including ISI marked Stainless Steel butt hinges with necessary screws and face veneers on both faces of shutters and making rectangular vision panel of 0.1sqm with 6 mm thick clear heat strengthened glass.complete as per direction of Engineer-in-charge. 3.00 Sqm 2867.49 Rupees Two Thousand Eight Hundred Sixty Seven and Forty Nine Paise Only 8602.47

16 Providing and fixing panelling minimum 5.0 mm thick glass panes for glazing in panelled or glazed shutters for doors, windows and clerestory windows as per direction of Engineer-in-charge. 1.00 Sqm 2389.11 Rupees Two Thousand Three Hundred Eighty Nine and Eleven Paise Only 2389.11

17 Providing and fixing bright finished brass handles of 125mm size with screws etc.complete as per direction of Engineer-in-charge. 2.00 Each 235.79 Rupees Two Hundred Thirty Five and Seventy Nine Paise Only 471.58

18 Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete as per direction of Engineer-in-charge. 1.00 Each 111.76 Rupees One Hundred Eleven and Seventy Six Paise Only 111.76

19 Providing and fixing bright finished brass tower bolts of 250x10mm (barrel type) with necessary screws etc. complete as per direction of Engineer-in-charge. 2.00 Each 405.71 Rupees Four Hundred Five and Seventy One Paise Only 811.42

20 Providing and fixing bright finished brass 100 mm mortice latch and lock with min. 4levers and a pair of lever handles of approved quality with necessary screws etc. complete as per direction of Engineer-in-charge. . 1.00 Each 785.19 Rupees Seven Hundred Eighty Five and Nineteen Paise Only 785.19

21 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete as per direction of Engineer-in-charge. 1.00 Each 1033.43 Rupees One Thousand Thirty Three and Forty Three Paise Only 1033.43

22 Providing and fixing aluminium sliding door bolts(aldrop) of 250 x16mm , ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. 1.00 Each 239.42 Rupees Two Hundred Thirty Nine and Forty Two Paise Only 239.42

23 Providing and fixing M.S. grills with made of M.S. flats, square or round bars to openings of required pattern/ frames of windows with rawl plugs screws etc. including priming coat with approved steel primer all complete. 812.00 Kgs 218.98 Rupees Two Hundred Eighteen and Ninety Eight Paise Only 177811.76

24 Supplying, fabricating, hoisting and fixing in position M.S. structual steel work E 250 (Fe 410W) in Roof trusses, purlins, girders, stanchions, crane gantries,Square/Round bars, rails, edging angles, frames, fastenings,brackets,machine foundations, as per site requirement etc. using standard steel rolled sections, including M.S. plates,foundation bolts, cutting to dead length where required, notching, drilling, riveting and/or welding, connecting with bolts and nuts, wedging, plumbing, including cutting, hoisting, fixing in position, all complete as directed by the Engineer-in-Charge. 30000.00 Kgs 122.84 Rupees One Hundred Twenty Two and Eighty Four Paise Only 3685200.00

25 Supplying and fixing rolling shutters of approved make, made of required size 80x1.25 mm M.S. laths with 1.25 mm thick top cover, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters painting and providing mechanical device chain and crank operation for operating rolling shutters.Complete the work as per the instructions of Engineer-in-charge. 24.00 Sqm 4442.06 Rupees Four Thousand Four Hundred Forty Two and Six Paise Only 106609.44

26 Providing and fixing 1 mm thick M.S. sliding-door/shutters, with frame and diagonal braces of 40x40x6 mm angle iron, 3 mm M.S. gusset plates at the junctions and corners, 25 mm dia pulley, 40x40x6 mm angle and T- iron guide,round bars etc at the top and bottom respectively, including applying a priming coat of approved steel primer complete as per the instructions of Engineer-In-charge. 40.00 Sqm 6032.56 Rupees Six Thousand Thirty Two and Fifty Six Paise Only 241302.40

27 Cement concrete flooring (1:2:4) of 40 mm thick with 20 mm nominal size stone aggregate finished with a floating coat (VDF) of neat cement finish, including cement slurry and castingin panels/making necessary cuts or grooves etc. complete all the work as per the instructions of Engineer-In-charge both in extended portion and in existing area. 712.20 Sqm 641.32 Rupees Six Hundred Forty One and Thirty Two Paise Only 456748.10

28 Providing and fixing precoated galvanised iron profile sheets (Roof & wall) (size,shape and pitch of corrugation as approved for roof/wall by Engineer-in-charge)0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 micronsepoxy primer on both side of the sheet and polyester top coat 15-18microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as per EIC. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required as per the instruction of Engineer-In-charge. 998.00 Sqm 678.62 Rupees Six Hundred Seventy Eight and Sixty Two Paise Only 677262.76

29 Providing and fixing precoated galvanised steel sheet roofing Ridges plain (500 - 600mm) accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete as per the instruction of Engineer-in-Charge. 76.00 Rmt 489.08 Rupees Four Hundred Eighty Nine and Eight Paise Only 37170.08

30 Plastering to internal brick/block wall with 15 mm thick on the rough side of single or half brick wall of cemnet mortor (1:6) including leveling,curing and making the level smooth and at all heights, plaster drip course/ groove in plastered surface or moulding to R.C.C. projections and execute the work complete as per direction of Engineer-in-charge. 442.00 Sqm 351.87 Rupees Three Hundred Fifty One and Eighty Seven Paise Only 155526.54

31 Plastering to ceiling with 12 mm thick on the rough side with cement mortor (1:4) including leveling,curing and making the level smooth and at all heights and execute the work complete as per direction of Engineer-in-charge. 42.00 Sqm 318.85 Rupees Three Hundred Eighteen and Eighty Five Paise Only 13391.70

32 Plastering to external brick/block wall with 18 mm cement plaster in two coats under layer 12 mm thick cement plaster on the rough side with cement mortor 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).including leveling,curing and making the level smooth and at all heights, plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.The work to be completed as per direction of Engineer-in-charge. 772.00 Sqm 476.41 Rupees Four Hundred Seventy Six and Forty One Paise Only 367788.52

33 Providing and applying internal wall and ceiling painting with two coats of premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50grams/ litre after applying white cement based putty of average thickness 1mm over the plastered wall surface including preparation of the surfces, with a coat of low VOC primer with emery paper to bring to smooth and even including applying additional coats wherever required to achieve even shade and colour of approved brand,complete as per direction of Engineer-in-charge. 724.92 Sqm 342.50 Rupees Three Hundred Forty Two and Fifty Paise Only 248285.10

34 Providing and Finishing walls with Acrylic Smooth exterior paint of required shade for New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) including scrapping,preparationof surface for completing the work as per direction of Engineer-in-charge. 1012.92 Sqm 147.55 Rupees One Hundred Forty Seven and Fifty Five Paise Only 149456.35

35 Providing and applying synthetic enamel paint for steel members, rolling shutters,door shutters,pipes ,grills,chequered plate,etc in Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture,filling joints,metal patti etc ,complete as per the direction of Engineer-in-charge. 800.00 Sqm 272.49 Rupees Two Hundred Seventy Two and Forty Nine Paise Only 217992.00

36 Dismantling dressed stone work in cementt mortor of ashlar face stone work , marble work or precast concrete work manually/ by mechanical means including stacking of serviceable and disposal of unserviceable material outside HAL area/upto a distance of 10km lead as per direction of Engineer-in-charge. 19.80 Cum 3075.12 Rupees Three Thousand Seventy Five and Twelve Paise Only 60887.38

37 Demolishing R.C.C. work by mechanical means and stockpiling at designated locations and disposal of dismantled materials up to a lead of 10 kilometre outside HAL, stacking serviceable and unserviceable material separately including cutting reinforcement bars,after making temporary proetction for existing service lines.complete as per direction of Engineer-in-charge. 47.00 Cum 2998.36 Rupees Two Thousand Nine Hundred Ninety Eight and Thirty Six Paise Only 140922.92

38 Demolishing brick work with cement mortar manually/ by mechanical means, after disconnecting the electrical service and AC lines if any, including stacking of serviceable material and disposal of dismantled materials up to a lead of 10 kilometre outside HAL.complete as per direction of Engineer-in-charge. 40.00 Cum 2324.01 Rupees Two Thousand Three Hundred Twenty Four and One Paise Only 92960.40

39 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.Nominal concrete 1:4:8 or richer mix (i/c equivalent design mix)and including stacking material and disposal of dismantled materials up to a lead of 10 kilometre outside HAL,after making temporary proetction for existing service linescomplete as per direction of Engineer-in-charge. 29.00 Cum 1812.64 Rupees One Thousand Eight Hundred Twelve and Sixty Four Paise Only 52566.56

40 Dismantling doors, windows and clerestory windows (Aluminum,steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead of area 3 sq. metres and below, including stacking material and handing over the useful materials to HAL maintenance department and disconnecting the service lines if any all as instructed by Engineer Incharge. 6.00 Each 337.36 Rupees Three Hundred Thirty Seven and Thirty Six Paise Only 2024.16

41 Dismantling roofing including ridges, hips, valleys and gutters etc.,and stacking the material within 50 metres lead and complete the work as per the directionof Engineer Incharge.

a) Galvalume sheets/G.I.sheet 48.00 Sqm 151.54 Rupees One Hundred Fifty One and Fifty Four Paise Only 7273.92

b) Asbestos cement sheet 124.00 Sqm 71.02 Rupees Seventy One and Two Paise Only 8806.48

42 Boring, providing and installation bored cast-in-situ reinforced cement concrete piles for Hangar,Annexe,service Buildings with grade M-25 of 450mm dia and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length(as per site requirement)for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap).All works to be completed as per direction of Engineer-in-charge. 168.00 Rmt 2093.14 Rupees Two Thousand Ninety Three and Fourteen Paise Only 351647.52

43 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved makeconforming to IS: 733 and IS: 1285, fixing with dash fasteners ofrequired diaand size, including necessary filling up the gaps atjunctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free,straight, mitred and jointed mechanically wherever required includingcleat angle, Aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, and all accessories for complete operatinal as per the directions of Engineer-in-charge. (Glazing, paneling to be paid for separately).

a) For Fixed Portion with Powder coated aluminium (minimum thickness of powder coating 50 micron) 250.00 Kgs 487.75 Rupees Four Hundred Eighty Seven and Seventy Five Paise Only 121937.50

b) Powder coated aluminium (minimum thickness of powder coating 50 micron) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required etc., complete as per the instruction of EIC. 500.00 Kgs 582.89 Rupees Five Hundred Eighty Two and Eighty Nine Paise Only 291445.00

44 Providing and fixing 12 mm thick prelaminated particle board flatpressed three layer or graded wood particle board conforming to IS:12823 Grade l Type ll,with decorative lamination on one side and balancing lamination on other side in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per directions of engineer in-charge. 10.00 Sqm 1046.71 Rupees One Thousand Forty Six and Seventy One Paise Only 10467.10

45 Providing and fixing with float glass panes of minimum 5 mm thickness (weight not less than 12.50 kg/sqm) glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket,cliping,clamps,beedings etc. complete as per the directions of engineer-in-charge. 60.00 Sqm 1382.92 Rupees One Thousand Three Hundred Eighty Two and Ninety Two Paise Only 82975.20

Sub-Total of Part 'A' - Civil Works (Excluding GST) Rupees One Crore Eighteen Lakh Thirty Two Thousand Five Hundred Ninety Seven and Thirty Six Paise Only 11832597.36

Part 'B' - Electrical Works

1 Supply, fixing to existing MS perlins at approx. 5.5 mtr height, including using suitable MS angle frame work with required fixing hardwares etc., as per site requirement, testing & commissioning of industrial type highbay LED lighting fixture of wattage not exceeding 100watts made out of high pressure diecast aluminium housing, diffuser made of high grade toughened glass, integral control gear, eye hook etc., (as per OEM standards). The technical parameters of lighting fixtures are as below: The luminaire should have Lumen efficacy ≥ 110lm/watt and lumen output not less than 11000lumens, PF>0.90 and Colour temprature shall be ≥5700K, CRI≥70, THD <10%, IP66/65 operating on single phase 230V voltage 50 Hz AC supply with voltage range 140-270V including necessary interconnections between driver and lighting fixtures and other standard accessories complete in all respects and as directed by Engineer in-charge. The fitting shall be of Crompton model no: TIP-320-100-57-SL-GL-NSG/ Equivalent model in other approved makes. LED used in the lighting fixtures should be one of the approved make. LM79 certification for luminares & LM80 certificate for LED shall be produced. 22.00 Nos 11584.75 Rupees Eleven Thousand Five Hundred Eighty Four and Seventy Five Paise Only 254864.50

2 Supply & fixing on the building at a height of 4-6mtr approx. including supply and fixing GI pipe bracket made out of 40mm dia class B GI pipe of 1.5Mtrs long bent to shape with necessary fixing hardwares etc., to fix on building / and testing & commissioning of building light LED light fixture of wattage not exceeding 70/72watts and lumens output not less than 7700/7920 lumens with necessary interconnections consisting of pressure die cast aluminum housing, optical cover made out of heat resistance toughened clear glass / polycarbonate with IP66, operating on single phase 230V 50Hz AC supply, efficient heat sink, colour temperature shall be 5700K±5%, suitable optics for maximizing the spread complete in all respects and as directed by engineer-in-change. The luminaries shall have specific lens for optical dispersion including control gear and power factor of control gear shall be >0.95. The fitting shall have internal surge protection of 4KV and external surge protection of 10KV. LM 79 certification for luminaries & LM80 certificate for LED shall be produced. Any approved make fitting meeting the above technical specification has to be supplied.The LED Light fixture shall be of Crompton model no:TRP-409-70-57-SL-GL-NSG /Equivalent model in other approved makes luminaries which meets the above technical specification. LED used in the luminaire should be one of approved make as per approved make list of HAL. 10.00 Nos 5569.49 Rupees Five Thousand Five Hundred Sixty Nine and Forty Nine Paise Only 55694.90

3 Supply and fixing on existing wall/ceiling, testing & commissioning of surface mounting, Batten type 1X18W/20W T8 LED Tube light (four feet) Luminaries with minimum lumens output of 1600 lumens, comprising of white powder coated CRCA sheet steel housing, operating on single phase 230V 50Hz AC supply, built-in electronic driver, Other standard accessories including necessary inter-connections, complete in all respects and as directed by engineer-in-chage. The LED tube & batten shall be of Bajaj BLRB DB 118 /Equivalent model of approved make luminaries which meets the above technical specification. complete in all respect and as directed by Engineer-in-charge. 10.00 Nos 1150.00 Rupees One Thousand One Hundred Fifty Only 11500.00

4 Supply, installation, testing & commissioning of 300mm dia 900 rpm heavy duty exhaust fan of any approved make with louvers, connecting cord with 6A, 3 pin plug top and with all necessary accessories, including making wall openings and replastering to smooth finish with matching paint etc., complete in all respects and as directed by Engineer-in-charge. 1.00 No 4731.36 Rupees Four Thousand Seven Hundred Thirty One and Thirty Six Paise Only 4731.36

5 Supply, installation, testing & commissioning of heavy duty oscillating type Air-circulator along with three speed regulator of any approved make with all connected accessories and interconnections, including power cord with 6A, 3 pin plug top and complete in all respects and as directed by Engineer-in-charge 10.00 Nos 9252.54 Rupees Nine Thousand Two Hundred Fifty Two and Fifty Four Paise Only 92525.40

6 Supply, fixing, testing & commissioning of the following factory built powder coated Double door MCB/MCCB DB of any approved make fabricated out of M.S. sheet steel enclosure & necessary cutouts for operating the MCB knobs & comprising of 200 amps tinned copper busbars & earthing bus with tapped holes including internal wiring with stranded copper PVC wires or suitable size copper strips etc. & fixing the DB in flush with wall/ on wall as per site requirement with necessary M.S. angle supports, chipping the wall and replastering to smooth finish etc., wherever required as per site condition, complete in all respects, as directed by Engineer-in-charge and comprising the following as detailed below:

a) 8 way (4+24) Double door VTPN MCCB DB 3.00 Nos 9839.44 Rupees Nine Thousand Eight Hundred Thirty Nine and Forty Four Paise Only 29518.32

b) 4 way (4 + 12), Horizontal Double door MCB DB 1.00 No 3959.97 Rupees Three Thousand Nine Hundred Fifty Nine and Ninety Seven Paise Only 3959.97

c) 12 way SPN Double door MCB DB 1.00 No 2240.86 Rupees Two Thousand Two Hundred Forty and Eighty Six Paise Only 2240.86

d) 125 A, 415V 36KA, FP MCCB 3.00 Nos 7946.08 Rupees Seven Thousand Nine Hundred Forty Six and Eight Paise Only 23838.24

e) 32 amps. ratings, 4P MCB, "C" curve, 10 KA breaking capacity. 1.00 No 1920.34 Rupees One Thousand Nine Hundred Twenty and Thirty Four Paise Only 1920.34

f) 32A, 240V, DP MCB, "C" curve, 10 KA breaking capacity. 1.00 No 634.99 Rupees Six Hundred Thirty Four and Ninety Nine Paise Only 634.99

g) 32 amps. ratings, TP MCB, "C" curve, 10 KA breaking capacity. 13.00 Nos 974.75 Rupees Nine Hundred Seventy Four and Seventy Five Paise Only 12671.75

h) 6-32 amps. ratings, SP MCB, "C" curve, 10 KA breaking capacity. 55.00 Nos 247.80 Rupees Two Hundred Forty Seven and Eighty Paise Only 13629.00

7 Wiring for light point / fan point / exhaust fan point/call bell point from nearest switch box with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, fan regulator, modular plate, suitable GI box and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. (as per detailed CPWD specifications for Group C wiring)

a) Wiring to single light point controlled by 1 No 6A, 250V gr. flush type modular SP switch complete in all respects. 10.00 Pts 1420.02 Rupees One Thousand Four Hundred Twenty and Two Paise Only 14200.20

b) Wiring to exhaust fan point using 6A, 250V gr. flush type modular SP switch housed along with other lighting switches/separate switch box if required and 3pin 6A, 250V gr. modular type socket housed near the exhaust fan complete in all respects. 1.00 Pt 1420.02 Rupees One Thousand Four Hundred Twenty and Two Paise Only 1420.02

8 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required 25.00 Nos 461.73 Rupees Four Hundred Sixty One and Seventy Three Paise Only 11543.25

9 Supplying and fixing following suitable size GI Box with modular plate and cover on front on surface or in recess, including providing and fixing 6 pin 5/6A & 15/16A modular socket outlet and 15/16 A modular switch, connections etc., as required. 8.00 Nos 567.23 Rupees Five Hundred Sixty Seven and Twenty Three Paise Only 4537.84

10 Wiring for circuit/submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required

a) 3 x 2.5 sq. mm (For lighting ckt from DB to Switch box) 100.00 Mtrs 266.19 Rupees Two Hundred Sixty Six and Nineteen Paise Only 26619.00

b) 3 x 4 sq. mm(For 6A & 16A power points) 350.00 Mtrs 323.30 Rupees Three Hundred Twenty Three and Thirty Paise Only 113155.00

11 Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. 4.00 Nos 1569.08 Rupees One Thousand Five Hundred Sixty Nine and Eight Paise Only 6276.32

12 Supplying and fixing 30/32A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30/32A "C" curve, TP MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required 4.00 Nos 3975.47 Rupees Three Thousand Nine Hundred Seventy Five and Forty Seven Paise Only 15901.88

13 Supply and fixing on MS perlins/wall using suitable angle iron frame work, fixing hardware, Cable junction boxes IP 65/66 with integrated membranes for cable entry of Hensel make (not less then 130x130x77mm) or equivalent model in Legrand/ Hager/ Schneider with cover and providing 10A 6way PVC connector inside the box as directed by Engineer -in-charge.(For High bay & building light fittings) 20.00 Nos 2888.98 Rupees Two Thousand Eight Hundred Eighty Eight and Ninety Eight Paise Only 57779.60

14 Supply, laying, testing & commissioning of following size LT armoured power cable

Supply & laying in the already excavated cable trench/cable tray/fixing on wall/duct wall with necessary M.S clamps / encasing in pipes etc., testing & commissioning of following size XLPE insulated Aluminium (Al) /Copper (cu) conductor 1100V gr., earthed Armoured (Arm)/un Armoured (un Arm) U.G cables as directed and as per technical specification and as detailed below. (Note:- Excavation, sand & Brick Protection, concrete cutting, reconcreting, casing pipes will be measured separately.)

a) 3.5CX 120 Sqmm Copper un armoured conductor. 10.00 Mtrs 10060.13 Rupees Ten Thousand Sixty and Thirteen Paise Only 100601.30

b) 3.5CX 95 Sqmm Copper un armoured conductor. 10.00 Mtrs 7589.32 Rupees Seven Thousand Five Hundred Eighty Nine and Thirty Two Paise Only 75893.20

c) 3.5CX 70 Sqmm Copper un armoured conductor. 10.00 Mtrs 5310.51 Rupees Five Thousand Three Hundred Ten and Fifty One Paise Only 53105.10

d) 3.5 CX 70 Sqmm Aluminium armoured conductor. 120.00 Mtrs 766.44 Rupees Seven Hundred Sixty Six and Forty Four Paise Only 91972.80

e) 3.5 CX 35 Sqmm Aluminium armoured conductor. 10.00 Mtrs 439.32 Rupees Four Hundred Thirty Nine and Thirty Two Paise Only 4393.20

f) 3.5CX 25 Sqmm Aluminium armoured conductor 5.00 Mtrs 340.66 Rupees Three Hundred Forty and Sixty Six Paise Only 1703.30

g) 4CX 10 Sqmm Aluminium armoured conductor. 200.00 Mtrs 276.25 Rupees Two Hundred Seventy Six and Twenty Five Paise Only 55250.00

h) 4CX 6 Sqmm Aluminium armoured conductor. 5.00 Mtrs 208.46 Rupees Two Hundred Eight and Forty Six Paise Only 1042.30

i) 3C X4 Sqmm Cu Arm LT Cable( for high bay light fittings) 450.00 Mtrs 360.15 Rupees Three Hundred Sixty and Fifteen Paise Only 162067.50

15 Supplying and making end termination with brass compression gland and aluminium/Copper lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium/Copper conductor cable of 1.1 KV grade as required

a) 3.5 CX 120 Sqmm Cu un-Arm LT Cable End Joint 2.00 Nos 830.00 Rupees Eight Hundred Thirty Only 1660.00

b) 3.5 CX 95 Sqmm Cu un-Arm LT Cable End Joint 2.00 Nos 600.00 Rupees Six Hundred Only 1200.00

c) 3.5 CX 70 Sqmm Cu un-Arm LT Cable End Joint 2.00 Nos 500.00 Rupees Five Hundred Only 1000.00

d) 3.5C X70 Sqmm Al Arm LT Cable End Joint 6.00 Nos 453.01 Rupees Four Hundred Fifty Three and One Paise Only 2718.06

e) 3.5CX 35 Sqmm Al Arm LT Cable End Joint 2.00 Nos 357.19 Rupees Three Hundred Fifty Seven and Nineteen Paise Only 714.38

f) 3.5CX 25 Sqmm Al Arm LT Cable End Joint 2.00 Nos 302.97 Rupees Three Hundred Two and Ninety Seven Paise Only 605.94

g) 4C X 10 Sqmm Al Arm LT Cable End Joint 12.00 Nos 260.39 Rupees Two Hundred Sixty and Thirty Nine Paise Only 3124.68

h) 4C X 6 Sqmm Al Arm LT Cable End Joint 2.00 Nos 310.00 Rupees Three Hundred Ten Only 620.00

i) 3C X 4 Sqmm Cu Arm LT Cable 71.00 Nos 200.00 Rupees Two Hundred Only 14200.00

16 Supplying and fixing of Hot dip galvanised Perforated type cable tray of following sizes, steel: As per IS:2062 / 1079, Galvanising : As per IS: 2629 / 4759 including all accessories like base slotted angle, horizontal elbow, horizontal tee, horizontal cross, horizontal reducer, vertical elbow up, inside, vertical elbow down, outside, coupler plate, fasteners etc.

a) Supplying and fixing of 100 x 50 x 1.6mm size Hot dip galvanised Perforated type cable tray 50.00 Mtrs 647.58 Rupees Six Hundred Forty Seven and Fifty Eight Paise Only 32379.00

b) Supplying and fixing of 225/200 x 50 x 1.6mm size Hot dip galvanised Perforated type cable tray 50.00 Mtrs 866.33 Rupees Eight Hundred Sixty Six and Thirty Three Paise Only 43316.50

17 Supply, Installation, Testing & commiissioning of LT Panel.(PTA) 1.00 Set 456399.15 Rupees Four Lakh Fifty Six Thousand Three Hundred Ninety Nine and Fifteen Paise Only 456399.15

Design, fabrication, supply, installation, testing and commissioning of Indoor type LT Panels suitable to be mounted on the brick pedestal/on M.S channel/angle frame work as per site requirement including M.S channel/angle frame work for erection of panel, with cable entry from bottom/top as per drawing coordination by EIC with removable gland plates with required knock-outs for incoming and outgoing cables. Panel shall be fabricated out of CRCA sheet steel folded and braced as necessary to provide a rigid support for all components,totally enclosed and degree of protection shall not be less than IP-54, multi-tier cubicle type formation with front hinged lockable doors for the individual feeders / compartments, preparation of surface and treatment by seven tank process, powder coated with approved colour for not less than 50 microns and all doors and covers shall be fully gasketed using good quality EPDM gasket and/or rubber strips, and to provide good quality locking arrangment, durable door opening & closing mechanism, Aluminium bus bars for three phases and neutral, bus bar insulators, heat shrinkable PVC sleeves etc., with necessary interconnections as specified in Technical specifications for electrical & mechanical works, comprising of following switchgear and accessories complete in all respects and as directed by Engineer-in-charge.

1) Current density shall not exceed 0.8A/sq.mm for Aluminium bus bars in LT Panel

2)All MCCBs in the LT panels shall be adjustable with thermal settings(80% to 100%), overload and short circuit releases including door interlocking device, front operating handle complete,ON and OFF indication of LED module etc. complete in all respects.

3)The operating height of the Panel shall not exceed 2.1 mtr. from FFL.

i) 1No - 630A, 415V gr. 50KA, TPN MCCB

ii) Lot - 800A TP + 400 N, 415V, short circuit rated 50KA for 1sec, Aluminium bus bars with busbar insulators, heat shrinkable PVC sleeves etc.

iii) 1No- Multi function meter (MFM/MDM) suitable for 3ph, 4 wire, 240V(L-N), 5A, CL-1, RS 485 Port Digital MFM/MDM of EM6400NG of Schneider or any equivalent make meeting technical specification of above MFM complete in all respect.

iv) 1Set of - 630/5A current transformers of class 1 and 15VA burden for metering.

v) 1No- (0-500V) range 96x96mm flush type voltmeter with RYB selector switch

vi) 1No 16A 415V gr TP 50KA MPCB of for tapping power for metering and control circuit

vii) 1Set - RYB indicating lamps of LED module with 6A SP MCB.

viii) 1Set- 6A, MCB for the protection of measuring instruments.

i) 1 No - 400A 415V gr. 36KA TPN MCCB

ii) 1 No - 250A 415V gr. 36KA TPN MCCB

iii) 1 No - 200A 415V gr. 36KA TPN MCCB

iv) 5 Nos - 160A 415V gr. 36KA TPN MCCB

v) 2Nos - 63A 415V gr. 36KA TPN MCCB

vi) 2Nos - 32A 415V gr. 36KA TPN MCCB

18 Brick Pedestal for LT panel erection

a) Construction of Brick masonry pedestal using Sub Class B Burnt bricks with 1:8 cement mortar as per site condition as directed by Engineer In Charge, including curing etc. 2.00 Cu. Mtrs 5783.53 Rupees Five Thousand Seven Hundred Eighty Three and Fifty Three Paise Only 11567.06

b) Providing 1:2:4 Cement Concreter using 20mm graded aggregate including curing etc., complete as directed by the Engineer-in-charge. 1.50 Cu. Mtrs 9091.01 Rupees Nine Thousand Ninety One and One Paise Only 13636.52

c) Rendering 12mm thick 1:6 cement plaster on fair faces of the above Brick masonry including curing as directed by Engineer In Charge. 4.00 Sq. Mtrs 306.25 Rupees Three Hundred Six and Twenty Five Paise Only 1225.00

19 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan). Including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil & refilling the same soil and disposal of surplus excavated soil as directed, with in a lead of 50m. 5.00 Cu. Mtrs 485.98 Rupees Four Hundred Eighty Five and Ninety Eight Paise Only 2429.90

20 Concrete cutting/Chipping/Bitumen Road the existing 1:2:4 cement concrete road /pavements / flooring / rock/stone etc., including removing debris from the work site and depositing in the place as directed by EIC. 1.50 Cu. Mtrs 3262.64 Rupees Three Thousand Two Hundred Sixty Two and Sixty Four Paise Only 4893.96

21 Removing & re-routing of existing LT cables

Disconnecting and removing the following size existing LT cables from the existing LT panel and lifting from the cable duct/cable trench as-is-basis without damaging the cable, re-routing/re-laying the same as directed by Engineer-in-charge including testing & commissioning of the cable complete in all respect. Note:- Excavation, concrete cutting will be measured separately.

a) LT/MV Cable ( up to 35 Sqmm) 200.00 Mtrs 27.10 Rupees Twenty Seven and Ten Paise Only 5420.00

b) LT/MV Cable ( above 35 sq. mm and upto 95 sq. mm) 100.00 Mtrs 43.56 Rupees Forty Three and Fifty Six Paise Only 4356.00

c) LT/MV Cable ( above 185 sq. mm and upto 400 sq. mm) 30.00 Mtrs 111.31 Rupees One Hundred Eleven and Thirty One Paise Only 3339.30

22 Disconnecting/dismantling & removal of 1 Set of Cubicle type existing LT panel with comprising of incoming and outgoings.(MCCB/SFU/MCB) items as-is-basis without any damage and handing over the same to the place as shown by Engineer-in-charge/Plant Maintenance department of Foundry & Forge Division( not more than 1KM) including loading, transportation, unloading etc., complete in all respects and as directed by the engineer-in-charge. 1.00 LS 4690.40 Rupees Four Thousand Six Hundred Ninety and Forty Paise Only 4690.40

23 Disconnecting, removing and re-fixing of existing cable tray at same area at approx. height 4 mtrs as per the instruction of EIC. Note:-MS angle support will be measured separately. 30.00 Mtrs 322.88 Rupees Three Hundred Twenty Two and Eighty Eight Paise Only 9686.40

24 Fabrication, supply, fixing / welding / grouting to the existing wall/cable duct suitable size MS angles/channel/flats with cross supports, clamps etc. support for cable tray including fixing hardwares & painting with two coats of black paint over a coat of primer complete in all respect and as directed by Engineer in charge. 500.00 Kgs 107.81 Rupees One Hundred Seven and Eighty One Paise Only 53905.00

25 Supplying and laying of 125mm PN8, PE-100 HDPE pipe confirming to IS 4984:1995 with necessary connecting / welding sockets / couplings / Tees/Bends in the excavated trench/duct/at road crossings for encasing cables. Any reputed make with ISI mark. complete and as directed by Engineer-in-charge. 15.00 Mtrs 988.14 Rupees Nine Hundred Eighty Eight and Fourteen Paise Only 14822.10

26 TIMER PANEL 1.00 Set 24819.49 Rupees Twenty Four Thousand Eight Hundred Nineteen and Forty Nine Paise Only 24819.49

a) Supply, installation, testing and commissioning of Outdoor weather proof 2rows 24 module module distribution board of Hensel Cat. No.KV 9224 M or equivalent in Legrand/ Hager/ Schneider make including suitable locking facility by means of built in lock with profile cylinder with set of Key's and with suitable size cover, cable entry on one side. The DB shall be mounted at suitable height on the wall using suitable size MS angle/channel frame work with painting as per EIC, with cable entry knock-outs, including rigid support for all components, required fasteners totally enclosed, dust and vermin proof and degree of protection shall not be less than IP-65 with necessary interconnections between incoming and outgoing MCB's, contactor and timer using suitable size flexible copper wires and comprising of following switchgear and accessories complete in all respects and as directed by Engineer-in-charge.

b) 1No- Modular digital time switch for street light & Building light control of Legrand Alpha Rex 3 D21 or equivalent approved make with one channel daily cycle unit suitable for daily programming to switch ON & OFF and operate on 230V single phase supply.

c) 1No- 32A 230V gr.10KA 4P MCB with overload and short circuit protection.

d) 1No-25A, ML1.5 contactor of L&T Cat.No.SS91851 with contactor coil suitable for 230V Single phase supply.

a) Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. 2.00 Nos 7232.69 Rupees Seven Thousand Two Hundred Thirty Two and Sixty Nine Paise Only 14465.38

b) Supplying & laying 25 mm X 5 mm GI strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of GI nut bolt & spring washer spaced at 50mm) 60.00 Mtrs 139.39 Rupees One Hundred Thirty Nine and Thirty Nine Paise Only 8363.40

c) Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. 100.00 Mtrs 38.58 Rupees Thirty Eight and Fifty Eight Paise Only 3858.00

28 Supply, installation, testing and commisioning of 4 Line insulated busbar GI conductor 100 Amps M-Type Shrouded GI Conductors (R,Y,B,G), bolted joint, joint cover, end cover, single pole hanger clamps and copper current collector. (complete in all aspects). 24.00 Mtrs 2042.40 Rupees Two Thousand Forty Two and Forty Paise Only 49017.60

Sub-Total of Part 'B' - Electrical Works (Excluding GST) Rupees Twenty Lakh Ninety Three Thousand Six Hundred Twenty Four and Sixty Five Paise Only 2093624.66

Total (Excluding GST) Rupees One Crore Thirty Nine Lakh Twenty Six Thousand Two Hundred Twenty Two and One Paise Only 13926222.02

The Tenderer has to Quote Percentage Above / Below as Specified and Percentage Shall be Quoted in Figures. Approximate Amount Put to Tender State Above or Below Percentage in Figures [Excluding GST] Amount

Tenderer's Quote (Excluding GST) 13926222.02 BELOW % 13926222.02

Add 18% GST Rupees Twenty Five Lakh Six Thousand Seven Hundred Nineteen and Ninety Six Paise Only 2506719.96

Grand Total (Including GST) Rupees One Crore Sixty Four Lakh Thirty Two Thousand Nine Hundred Forty One and Ninety Seven Paise Only 16432941.98

Note: The tenderer has to quote percentage above / below against the total amount considering the specified standard rates. If the contractor does not quote any percentage above / below on the total amount, the tender shall be treated as invalid and will not be considered.

WARNING: PLEASE ENTER PERCENTAGE QUOTE

HINDUSTAN AERONAUTICS LIMITED

Facilities Management Division

Pre-Qulification Profile (To Be uploaded along with Part A)

Tender Ref No. or Contract No.: HAL/FMD/C-50A/24-25

Name of Work: Proposed Extension of Ring Rolling Inspection Hanger Building on Both Sides Including Civil, Electrical Works at Foundry & Forge Division, HAL(BC).

Estimated Amount in Lakhs.: 164.7

Tender Notice Date:(DD/MM/YYYY) 24.12.2024 Can we give in DD/MM/YYYY

Complition Period(In months) 8

PROVISIONAL GST ID NO. for HAL 29AAACH3641R1Z3 Kindly mention at Col I J &K as " Any Other related Information"

Sl.No Description Details Enclosed / Not Enclosed Any Other Related Information Remarks

1 Name of the Individual / Firm / Company: * Mandatory Pls enter name

2 Type of ownership Related Document to be Uploaded to eProcurement Portal

3 Year of Estblishment of Company/Business

4 If Other, please specify

5 Details of Constitution or Legal Status such as certificate of incorporation, shops and establishments, etc., If not enclosed reasons be to recorded here

6 Address for correspondence:

8 PAN no and Name of Holder

9 PF number (If any)

11 (a) Service Tax Registration No

11 (b) Goods and Service Tax ID No.

12 Contact details

Contact person name Pls

Ph. No. with STD code

FAX No. with STD code 5 6

13 Registered Contractor

If Registered Contractor with HAL Yes/ No Pls Enter Related Document to be Uploaded to eProcurement Portal * Category: A = Above 25 Crores B = 15Crore to 25 Crores C = 5Crore to 15 Crores D = 1 Crore to 5 Crores E = Lessthan 100 Lakhs to 75 Lakhs F = 75 Lakhs to 50 Lakhs 0 7 .A1 1

Name of Organisation 199999 7 A 2

Category and Registration No. 200000 6 B 3

PEMD Amount ( If paid ) 499999 6 C 4

not required Need to Fill Column 19 no comparision 500000 5 D 5

14 I.T Returns for past 03 years 999999 5 E 6

2024-25 Pls Select 'Yes','No' for IT Returns for all the 3 years 2499999 4

15 Maximum value of works excuted during the followinf 5 years. . (In Lakhs)

2019 - 2020 Pls enter Finiancial Turnover in Rupees for all the years NOTE: The value of max work to be supported with the details of Works executed for each year including name of the organisation with period of execution. Here last 3 years cells to be considered to Check Annual Turn Over for 30 % value of Estimation given above 1 6.00 7.00 0 0

Avg Annual Turnover criteria is not met

16 DETAIL OF WORK ON HAND UPTO N-Months (N-contract period) [For Bid capacity calculation] NOTE : PROVISION for 10 works are given. If more, a separate similar sheet to be made showing all the works with all details as per this FORMAT and same to Uploaded. However, 9 works details to be provided and balance work value of other works to be added and to be provided in 10th row as OTHER works.

Sl.No(work No) Name of Organization with address Name of the work on hand Amount of Contract Rs (in Lakhs) Period of CONTRACT in months Date of Commencement of work as Work Order in dd/mm/yyyy Probable date of Completion as Agreed Actual progress achieved till date of Tender Notification Rs (in Lakhs) Balance value of work on hand [Col.(3)-Col.(7)] Rs (in Lakhs) Remarks If Any 0.00

8 0.00 Max Turn Over 07-08 8500000

9 0.00 Current Level to be brought by adding 10% for every year 10-11 8500000 X 1.1 X 1.1 X 1.1

10 0.00 Turn Over to considered A 11313500

0.00 Balance Work On Hand 207452000

Bid Capacity 0.00 Bid Capacity Criteria is not Met this shouldf be hidden while uploading

17 Work Schedule for completion of works with in stipulated time [Please enclose action plan / bar chart as to indicate the completion of work, within the scheduled time (contract period)] Bid Capacity (2 X A X N) - B

Related Document to be Uploaded -162198000

18 Quantity of work Excuted during the last three years

Earthwork [in Cum]

Concrete work [in Cum]

Reinforcement steel [in MT]

Any other quantity of items tenderer would like to mention

19 Bank(s) details: [Copy of the cheque leaf to be uploaded]

19a Bank Account No. Related Document to be Uploaded to eProcurement Portal (Note Canceled cheque leaf to be uploaded)

Name of the Bank

Type of Account

19b Bank Statement for past three month

19c Latest Over draft Facilties with Bank enter Name of Bank, Date of Issue and Value of Over Draft

20 Latest Bankers Solvency Certificate from Nationalized/ scheduled Bank issued NOT before 12 months from the date of Tender Notice. SOLVENCY solvency cal

Name of Bank & Branch Pls Related Document to be Uploaded to eProcurement Portal 24.12.2024 1-Jul 0 40000

Date of Issue(dd-mm-yyyy) #VALUE! 200000 40000

Value Rs. In Lakhs 200001 150000

Solvency value is as per NIT

21 Experience of having successfully completed similar works during last 7 years ending last day of previous month. [Work experience certificates / Completion certificates should be uploaded for verification]. [Latest work experience certificate may be uploaded] (i) THREE similar completed works each costing not less than the amount equal to 40% of the estimated cost. (ii) TWO similar completed works each costing not less than the amount equal to 50% of the estimated cost. (iii) ONE similar completed work each costing not less than the amount equal to 80% of the estimated cost. [Amount put to the Tender] 40000 500001 250000

Completed similar works during last 7 years You are Not Eligible Pls Select Works Completed during last 7 years 1000000 250000

Work NoI Type of Work [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal 1000001 500000

Name of The organisation

Brief Description of Work: 2000000 500000

Completed value of Work in Rs. Lakh: 2000001 1000000

Date of Commencement of Work [DD/MM/YYYY]: 4000000 1000000

Date of Actual Completion of Work[DD/MM/YYYY]: 4000001 2000000

Work No II Type of Work [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal 10000000 2000000

Name of The organisation

Brief Description of Work

Completed value of Work in Rs. Lakh:

Date of Commencement of Work [DD/MM/YYYY]:

Date of Actual Completion of Work[DD/MM/YYYY]: work done

Work No III Type of Work and Organisation name [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal 24.12.2024 2555

Name of The organisation

Brief Description of Work: #VALUE!

Completed value of Work in Rs. Lakh:

Date of Commencement of Work [DD/MM/YYYY]:

Date of Actual Completion of Work[DD/MM/YYYY]:

Work Competion is NOT with in 7 years

Valid Class I Electrical Licence [or] Undertaking for engaging Electrical Contractor possessing valid Class I Electrical Licence Please Enter Electricial Licence No Electricial Licence valid upto Related Document to be Uploaded to eProcurement Portal

22 DEAILS OF TECHNICAL PERSONNEL AVAILABLE( if space provided is insufficant separate sheet to be uploaded with the same format as below)

Sl.No Name of members or technical personllel avalable in the organization Qualification of similar nature number of years of experience

23 DETAILS OF MACHINERY AVAILABLE

Sl.No Name of Mechinery No Make Year of Manufacture

1 Concrete Mixers - Type etc

2 Vibrators - Diesel - Electrical

3 Weiding equipment's

4 a) Rectifiers

5 b) Welding Generators

6 Erection equipment's

10 Water Lifting motor pumps

13 Drilling Equipment's

16 Stone crushers

17 Bitumen hot mixture plant

18 Bitume boiler

20 Batching plants

21 Vibratory rollers

23 Cranes-Details

24 Concrete pumps

26 Rock breakers

27 Transit mixers

29 Weight batches

24 Details of person holding the power of Attorney (If different from contact person)

Name Related Document to be Uploaded to eProcurement Portal

Ph. No. with STD code

FAX No. with STD code

I/We declare and confirm that - 1. All information and attachments submitted in this application are true and correct. 2. I/We are aware that any false information provided herein will result in the rejection of my application and suspension of any registrations granted. 3. I/We shall not make refund claims of expenditure incurred in processing this application. Pls enter

26 Tender Document Cost and EMD details

Descipttion Enclosed / Not enclosed Valid upto [in case of BG] Related Document to be Uploaded to eProcurement Portal

Tender cost Enclosed

27 Average annual financial turn over during the last 3 years, ending 31st March 2024 [ should not be less than 30% of amount put to tender] and details for last 5 years to be provided to assess the bid capacity. The values provided to be supported by uploading Balance Sheet along with Profit & loss account statement. . (In Lakhs)

2023-24 Pls Select 'Yes','No' for Annual financial turn over for all the 3 years

Average 0.00 FALSE

Balance sheet and Profit & loss statement for last 05 years