REPAIR MAINT TO DAMAGED ROOF CHAJJA BROKEN JOINERY CURTAIN ROD KITCHEN HARDWARE CUPBOARD SANITARY FITTING PAINTING BOUNDARY WALL GARBAGE BINS AND OTHER MISC BR WORKS

Repair to ends of chajjas/ parapets by removing old concrete, loose material ,& cleaning of the reinforcement and finishing the surface in cement mortar 1:3 , finished fair & even and making good with existing finishes all as specified and directed. Note: Rate quoted by the tenderer shall be deemed to inclusive of double steel scaffolding and water proofing compound.

Repair to cracks and damaged existing surface of RCC roof slab/RCC facia/RCC chajja upto double storey (Approx height 7.50 Mtr from the natural ground level) by structural strengthing using injection pressure grouting with Sikadur 52, low viscous epoxy grout of Make M/s Sika India Pvt Ltd, or equivalent in M/s Fosroc Chemicals, M/s Thermex, M /s BOSTIk India pvt limited, M/s STP Limited, (as approved by GE), complete all as manufacturers and all as specified and directed by GE as under:-

Providing and drilling 10mm dia holes using pneumatic drill as per site condition but not exceeding 50cm c/c in zig-zag patten for 75mm depth and fixing high pressure bear up Metal/Aluminium body indection packer along the holes and packing with Sika rep Micro Crete 4, rapid setting cement based plugging mortar of Make M/s Sika India Pvt Ltd, or equivalent in M/s Fosroc Chemicals, M/s Thermex, M /s BOSTIk India pvt limited, M/s STP Limited, (as approved by GE)

Mixing base and hardner of Sikadur 52, low viscous solvent free epoxy injection grout of Make M/s Sika India Pvt Ltd, or equivalent in M/s Fosroc Chemicals, M/s Thermex, M/s BOSTIk India pvt limited, M/s STP Limited, (as approved by GE) using slow speed electricity operated mixing paddle (200-300RPM) and injecting the same using electrically operated high pressure (upto 1000 Kgf/SqCM) pump until refusal to adjacent complete as per manufacturers specification.

Cutting and flushing the nozzoles and excess materials with a sharp scraper to take away sharp protrusions and to get a smooth and flat finish

(a) Note : The work under (Item No. 1 to 5 of BOQ) shall be carried out through authorized and qualified applicators of the any following manufacturer only. M/s Sika India Pvt Ltd, M/s Fosroc Chemicals, M/s STP Limited, M/s BOSTIk India pvt limited,M/s Thermax Limited

(b) A performance guarantee certificate for two years shall be submitted by the contractor to the GE on completion of work as specified.

M&L for Dismantling/ taking down old existing unserviceable cement plaster, loose/ unsound weaken cement concrete of any description and in any position from existing external / internal surface of RCC roof/ slab/ beams/ columns/ RCC facias for an average depth of 25mm (Approx height 7.5m from natural ground level) with power driven pneumatic flat/pointed chisel and removing the honeycombed area including all the corners and making a neat profile of the cavities, roughen the smooth surface , scrapping out/removing corrosion all loose/scale/rust etc form the visible reinforcement by applying rust remover such as Rust Off 100 of make M/s Sika India Pvt Ltd, or equivalent in M/s Fosroc Chemicals, M/s BOSTIk India pvt limited, M/s STP Limited, M/s Thermax Limited (as approved by GE) and cleaning the steel reinforcement properly all as per manufacturer instructions and all as specified and directed and comprising of below mentioned process :-

(a) Providing cement based admixed with Sikacim, integral waterproofing liquid M/s Sika India Pvt Ltd, or equivalent in M/s Fosroc Chemicals, , M/s BOSTIk India pvt limited, M/s STP Limited, M/s Thermex Ltd (as approved by GE) @ 0.2% by weight of cement or as per manufacturer’s instructions over a coat of acrylic emulsion bonding agent such as per as Sika Latex in 1:1:3 ratio of Make M/s Sika India Pvt Ltd, or equivalent in M/S Fosroc chemicals, M/s BOSTIk India pvt limited, M/s STP Limited, M/s Thermex Ltd (as approved by GE) having specific gravity of 1.02 or as per manufacturer’s instructions with necessary surface preparation such as creating mechanical key like roughening the surface by scrabbing, grit blasting and cleaning the existing surface using high pressure water jet machine having pressure upto 500 bar pressure to remove the dirt, dust, loose particles , wax, efforencene and other contaminations from the surface of RCC columns/ beams/ slabs/ facia/ any brick/ stone surfaces etc all as per manufacturer instructions and all as specified and directed by Engineer-in-Charge.

(b) Providing and applying FRIAZINC R, corrosion inhabiliting Active Zinc rich primer of make M/s Sika India Pvt Ltd, or equivalent in M/s Fosroc Chemicals, , M/s BOSTIk India pvt limited, M/s STP Limited, M/s Thermex Ltd (as approved by GE) along the exposed reinforcement surface property and allowed to dry.

(c) Providing and applying Hibond, Epoxy based Thixotropic bonding adhesive of Make of M/s Sika India Pvt Ltd, or equivalent in M/s Fosroc Chemicals, M/s BOSTIk India pvt limited, M/s STP Limited, M/s Thermex Ltd ( as approved by GE) over the prepared concrete surface to get a good bonding between existing concrete surface and providing Sika Rep Microcrete 4 Fiber reinforced cementitious repair micro concrete of make M/s Sika India Pvt Ltd, or equivalent in M/s Fosroc Chemicals, M/s BOSTIk India pvt limited, M/s STP Limited, M/s Thermex Ltd (as approved by GE) over Epoxy based bonding agent applied area before 6 Hrs etc including providing necessary proportions , bracing and runners to relieve the member from the load coming on it including scaffolding leak proof shuttering with working platform as required and as per design and pattern complete including preparing the surface to match with the existing surface all as specified and directed.

(d) Note : The work under (Item No. 8 to 11 of BOQ) shall be carried out through authorized and qualified applicators of the any following manufacturer only. M/s Sika India Pvt Ltd, M/s Fosroc Chemicals, M/s STP Limited, M/s BOSTIk India pvt limited,M/s Thermax Limited

(i) A performance guarantee certificate for two years shall be submitted by the contractor to the GE on completion of work as specified.

(ii) The unit rate quoted for item No. 8 to 11 of BOQ is deemed to be included for Removing of accumulated earth of any width and depth upto 15 cm cleaning/cutting the grass with hand operated petrol/kerosene driven grass cutting machine and removing the grass waste around 3 m from plinth protection to outside MD land Note: Periodicity of cutting of grass shall be before commencement of work and after completion of repairs.

Checking of floor, plinth, plaster etc requiring masonry work and carrying out minor repairs such as edges, patches etc, including petty repairs material like sand, cement & aggregate to make it functional complete all as specified and as directed by Engineer-in-Charge. The rates for plastering / plinth include for: (a) Preparing the surfaces. (b) Thickness of plaster/plinth key in joints, etc. (c) Anises, chamfers of any width, internal rounded angles upto 80mm in width or girth external rounded angles upto 80mm in width or girth. (d) All materials, labour and equipment & supply of integral waterproofing compound, (e) Scoring surface of plastering for key, where the surface is not required to be finished fair. (f) Plastering in patches (in repairs), exc 3 sq.m each patch, for preparing old walls to receive plastering'. Nothing extra shall be admissible for matching with existing work etc. (g) Any individual patch (other than nail hole, plug hole, etc.) are included for provided existing surface finish .

Removing plant/Uprooting of vegetation growth including roots on wall/roof/parapet near pipes etc and applying acid treatment after removing roots for preventing regrowth and making good disturbed surfaces/area in superficial area exc 150sq.cm but n.exc 400 sq.cm and averaging depth not exceeding 10 cm by using PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) or 10mm thick plastering in cement mortar 1:3 as required and finishing the surfaces to match with the existing surface complete all as specified and directed.

M&L for providing and laying / fixing TPO membrane of non-flammable waterproofing of roof which shall be 1.5mm thick loose laid membrane using Fosroc Proofex ORG membrane, layers are overlaped to achieve a minimum weld of 110mm. Hot air welding can be either hand applied or by means of automatic machines and the roll's either end are overlapped with 110mm are in staggered position and the membrane shall be laid over the layers of non-woven geotextile fiber. The seperation layer provided to prevent the mechanical abrasion and cushioning between the fosroc proofex ORG membrane and the concrete substructure . The termination of fosroc proofex ORG by aluminium strip anchoring. Note: Work shall be executed directly by manufacturer or through their authorised and qualified applicators, of any following manufacturer only.M/s Fosroc chemicals, M/s Thermax Limited, M/s Tiki Tar Danosa India Ltd.

M&L for cement plaster rendering 15mm thick on fair faces of brick/concrete surfaces with two coats i.e. (10mm thick backing coat in CM 1:6 and 5mm thick finishing coat in CM 1:4) and mixed with liquid water proofing compound as per manufacturer instructions, finished even and smooth without using extra cement (WPC to be measured and paid separately) and Taking down old cement plaster on brick or stone walls, or concrete walls etc., hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises complete all as per specified and directed.

M&L applying two coat of cement based paint over a coat of primer, including preparation of newly plastered wall surfaces with smooth finish of any description, complete all as specified and as directed.

M&L for cement plaster rendering 10mm thick in CM 1:6 on fair faces of brickwork or concrete surface as on wall finished even and smooth without using extra cement and taking down old cement plaster on brick or stone walls, or concrete walls etc., hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises complete all as per specified and directed.

M & L for preparation of new plastered surfaces of walls applying wall care putty of one coat over plastered surface to prepare the surface even and smooth finish and applying two finishing coat of oil bound distemper over a coat of primer complete all as specified and directed.

Taking down and re-fixing the same existing aluminium door/window/partitions (each shutter area n. exc 5sqm) after carrying out certain repairs as required, removing the existing beading and fixing new (i.e. including change of Handles, hinges, star lock, rubber beadings, bottom bearing, clips etc) rubber beading of suitable size with adhesive, overhauling of floor springs including repairing/cleaning/greasing etc and making the same fully functional all as specified and directed.

Taking down chowkhat or frame (wooden/steel) exceeding 1.50 Sqm and not exceeding 4.0 Sqm each with shutter (with out taking off shutters from the frame) all as specified and as directed.

Taking down shutters of any description exc 1.0 Sqm and n.exc 2.0 Sqm each complete all as specified and directed.

M&L Second class hard wood plain, solid, straight Chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

Supply and Fixing 30 mm thick factory made flush shutter solid core construction with block board core and plywood face panels, comercial type on both faces complete all as specified and directed.

S&F 2nd class hard wood 35mm thick Factory made plain framed panelled shutter (Two Panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered partical board with commercial veneering on both faces. The size of rail and stile as per IS 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 2nd class hard wood 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); all as specified and directed.

Preparation of new wood or wooden surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed

Supply and fixing 100mm long Butt hinges medium weight cold rolled stainless steel, and fixed complete all as specified and as directed.

Supply and fixing in repair 100mm long Butt hinges medium weight cold rolled stainless steel, fixed to wooden frame/welded to metal frame complete all as specified and as directed.

Supply and fixing 200 mm long aluminium anodized barrel tower bolt extruded section complete all as specified and as directed.

Supply and fixing in repairs 200 mm long aluminium anodized barrel tower bolt extruded section complete all as specified and as directed.

S&F aluminium handles cast type anodised 200 mm long complete all as specified and as directed.

Supply and fixing in repairs aluminium handles cast type anodised 200 mm long complete all as specified and as directed.

S&F Butt hinges 75 mm long medium weight cold rolled stainless steel complete all as specified and as directed.

Supply and fixing 150 mm long aluminium anodized barrel tower bolt extruded section complete all as specified and as directed.

Supply and fixing in repairs 150 mm long aluminium anodized barrel tower bolt extruded section complete all as specified and as directed.

Supply and fixing aluminium handles cast type anodized 150 mm long complete all as specified and as directed.

Supply and fixing in repairs aluminium handles cast type anodised 150 mm long complete all as specified and as directed.

S&F 300mm aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extrudud sections or cast- aluminium alloy and fixed complete all as specified and as directed.

Supply and Fixing in repairs 300mm aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extrudud sections or cast- aluminium alloy and fixed complete all as specified and as directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm complete all as specified and directed.

S&F in repairs Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm complete all as specified and directed.

S&F in repairs 300mm, ordinary mild steel rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F in repairs floor door stopper of aluminium alloy body and tongue anodized with hard drawn steel spring fixed in floor overall 140mm complete all as specified and as directed.

M&L Hacking out old broken glass (any thickness, size, quality or description) from wooden frames/steel frames glazed with putty or fixed with beads and material and labour for 4mm thick plain sheet glass ordinary quality and glazed with oil putty or fixed with fillets 2nd class hard wood of sectional area not exc 3 Sqcm and glass not exc 0.5 sqm in each pane complete all as specified and directed.

M&L Hacking out old broken glass (any thickness, size, quality or description) from wooden frames/steel frames glazed with putty or fixed with beads and material and labour for 4mm thick plain sheet glass ordinary quality and glazed with oil putty or fixed with fillets 2nd class hard wood of sectional area not exc 3 Sqcm and glass exc 0.5 sqm in each pane complete all as specified and directed.

S&F in repair 20-25mm thick SS curtain rail incl brackets fixed into wall using wooden plug, screw etc complete all as specified and directed.

Petty repair to door shutters for easy closing/opening (size upto 3 Sqm) including minor repair and easing, adjustment/alignment to openable with assessories and including taking down and refixing, tightening of hinges or changing the position of hinges,welding of hinges door to frame adjustment of tower bolts, sliding bolts with new screws etc, complete all as specified and directed.

Taking down chowkhat or frame(wooden/steel) not exceeding 1.5 Sqm each with shutter (with out taking off shutters from the frame) all as specified and as directed.

S&F in Steel windows with side hung shutters including projecting type hinges, frame with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F 4 mm thick sheet glass ordinary quality and glazing complete in square n exc 0.50sqm in each pane complete all as specified and directed.

S&F 4 mm thick sheet glass ordinary quality and glazing complete in square exc 0.50sqm in each pane complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube complete all as specified and directed.

S&F Factory made Solid PVC Door Shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified and directed.

Petty repair to easing of wooden window, wooden ventilator, cupboard door, wardrobe door, PVC door, window shutters, kitchen cupboard shutters, show case shutter drawers including fixing of screws adjusting handles, knobs tightening piano hinges including misc small adjustments , (size upto 3 Sqm). minor repair and easying and adjustment/alignment to openable with accessories and including taking down and refixing complete all as directed.

Supply only MS Box type hinges 50mm.

Supply only MS Handle 100mm.

Supply only MS tower bolt 75mm

Supply and fixing in repair steel window peg stay all as specified and directed.

Petty repair to aluminium section/glass doors, windows, ventilators, partitions and making good the same size upto 2 Sqm (i.e. including change of Handles, hinges, star lock, rubber beadings, bottom bearing, clips etc) included taking down and refixing complete all as specified and directed.

Supply and fixing in repairs Powder coated aluminium (minimum thickness of powder coating 50 micron) frame work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws,included rubber beading complete all as per architectural drawings and as directed.

Supply and fixing in repairs powder coated aluminium for shutters of window and ventilator shutters, side hung type without sash bars/sliding type, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.). hinges type B-21 100mm long (2 No.) suitable handle (1 No.) complete all as specified, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, star lock, including rubber beading complete all as per architectural drawings and the directions of Engineer-in-Charge.

S&F in aluminium anodised grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC15) of approved design/pattern(DG 104), with approved standard section and fixed to existing window frame with CP brass/stainles steel screwnot less than 50mm and @ 200mm c/c, incl cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised alu standard section ( 28mm x 19mm x 2mm thick) around the opening

S&F Aluminium body door closer hydraulically regulated,designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed including taking existing one complete as directed.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel covert governing pivot made of brass, other parts made of mild steel heavy duty in repairs complete all as specified and directed.

S&F 5mm thick rubber beading strips of entrance doors having width exc 3cm and not exc 5cm to arrest entry of insects including taking down existing one complete all as specified and as directed

Applying silicon sealent on joints of wall,cill jambs roof etc complete all as specified as directed

Supply & Fixing of UPVC glazed 3 track-2 panel sliding windows with mesh made out of multi chambered uPVC sections with TPE gaskets having isolated drainage and reinforced with Galvanized iron profiles throught out the window. The outer frame having an overall size of 108 x 48 mm with reinforcement of 1.2mm thickness and sash with overall size of 38 x 61 mm with reinforcement of 1.2 mm thickness mesh sash of overall size 38 x 58mm Fiber mesh reinforced with 1.2 mm of GI. Glazing bead for fixing of glass shall be of size 16mm x 19mm and TPV gasket. Windows will be provided with 5mm thick plain float glass and stainless steel wiremesh, With "Astrapia" hardware or equivalent & Single point locking system of flush lock. Wall thickness of frame & sash shall be 2-2.2mm complete all as specified and directed.

S&F 12 mm thick toughened glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required and glass fixing with fish mouth channel & patch fittings included as approved material, fixing with all accessories and glass joints should be filled with weather proof silicon including fixing to wall for all arrangments and opening push and pull arrangements for double door & for top and bottom for pivot and lock patch and including door floor spring automatic arrangements materials and fixing including, permanent fixing wall for all arrangement including fittings, complete all as specified and directed Note:- (a) Glass fixing to wall and opening arrangement necessary all fitting and screws included as directed by Engineer in Charge. (b) Glass fixing with fish mouth channel and glass joints should be filled with weather proof silicon, MS portal materials and fixing cost included as directed by Engineer in Charge. (c) The above cost included for double glass door opening (push and pull type) any size, including all materials and necessary fittings for all fixing arrangement.

S&F in repair looking mirror of size 600mm x 450mm on commerical ply wood 6mm thick with PVC/ wooden moulding beading fixed to wooden plugs with chromium plated brass, screws and cup, washers, aluminium frame and fixed complete all as specified and directed.

Supply and fixing in repairs MS Mortise lock, 4 levers vertical type, size 100 mm for fixing to glass all as specified and directed.

M&L 18/19mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame work including taking down old complete all as specified and as directed.

S&F Decorative laminates of 0.90 mm thick type matt finish, colour and pattern as approved including taking down existing one complete all as specified and as directed.

S&F Magnetic catches with 8mm dia steel ball and brass body and striking plate including taking down existing one complete all as specified and directed.

S&F Chromium plated stainless steel wire Thali basket (storage basket ) pull out type, size 480x150x200mm of grade 304 with necessary fixing clips etc complete all as specified and directed.

S&F Chromium plated stainless steel wire basket (storage basket) pull out type, size 940x580x580mm of grade 304 with necessary fixing clips etc and all as specified and as directed.

S&F Chromium plated stainless steel wire basket (cutlery basket) pull out type, size 480x500x100mm of grade 304 with necessary fixing clips etc complete all as specified and as directed.

S&F Chromium plated stainless steel wire Bottle pull out basket (storage basket) pull out type, size 100x150x750mm of grade 304 with necessary fixing clips etc complete all as specified and directed.

Supply and fixing of Stainless steel handle 100mm size, D type, complete all as specified and directed.

Supply and fixing of Stainless steel handle 150mm size, D type, complete all as specified and directed.

S&F Chromium plated stainless steel wire saucer basket (storage basket) pull out type, size 480x500x150mm of grade 304 with necessary fixing clips etc complete all as specified and directed.

Supply and fixing of Stainless steel self closing hinges, 50mm size 8 crank, for kitchen cabinet, complete all as specified and directed.

Supply and fixing of stainless steel self closing hinges, 75mm size, 8 crank for cubboard shutter complete all as specified and directed.

S&F in repair factory made WPC single extruded 100% lead free ISO certified board of 18mm thick pre laminated both side, shutter for kitchen / room cupboard. The laminated shutter shall be of 0.14 micron pre laminated both side with different design and density not less than 700 kg / cum manufactured by an ISO 9001 2015 certified company the 18mm board will be water proof, termite proof and borer proof and shall have good screw holding capacity complete all as specified and directed.

S&F in repair SS auto closing hinges 35mm length 8 crank bright finish fixed to cupboard including screw, plugs etc. complete all as specified and directed.

S&F in repair 100mm SS handle fancy type fixed in cupboard shutter complete all as specified and directed.

S&F Sinks without drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm fixed in repairs all as specified and directed. Make : M/s Diamond / Nirali / Amco / TATA.

S&F 32 mm Waste Coupling fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed including taking down existing one complete all as specified and as directed.

Petty repair to wall mixer,basin mixer,sink mixer etc including replacement of spindle brass, Jumper brass, rubber washer, head incl taking down and refixing ete all as specified and directed

S&F in repair Brass Chromium plated wall mixer for mixing hot & cold water screwed down for 15mm bore iron pipe complete all as specified and directed.

S&F in repairs 2 way bib cock with wall flange PTMT screwed down screwed for iron pipe in repairs 15mm bore complete all as specified and as directed.

S&F Plate rack of size 65 cm x 96 cm (heavy duty) made of stainless steel fixed in repairs complete all as specified and directed.

S&F Sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm fixed in repairs all as specified and directed. Make : M/s Diamond / Nirali / Amco / TATA.

M&L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over screed bed or bedding layer of mortar 20mm thick for laying floor finishes in cement mortar (1:4) all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

Petty repair to renewing/matching glazed or ceramic coloured tiles in floors/walls in patches area not exceeding 5.00 Sqm including dismantling, removing and cleaning old tiles preparing beds and laying screed bed in CM 1:4 setting, jointing and pointing new or old tiles and joints filling and apply white cement and complete all as specified and directed

M&L Vitrified Ceramic tiles 8-10 mm thick, (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including screed bed or bedding layer, 15 mm thick in Cement Mortar (1:6) complete including dismantling of existing old tiles and disposal to outside MD land all as specified and as directed.

M&L Vitrified Ceramic tiles 8-10 mm thick, (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertcal surfaces such as skirting/ dado etc. set and jointed in neat cement slurry and pointed in coloured / white cement to match the tiles inc rendering 10mm thick in CM 1:4 on fair faces of brick work or concrete surfaces as in backing coat including dismantling of existing old tiles and disposal to outside MD land all as specified and as directed.

Material and labour for 25 mm thick PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in flooring surface as in level course etc including demolition of existing old cement concrete, including disposal of demolition material upto 500mtr from MD land complete all as specified and directed.

Supply and fixing Anodized aluminium size 605 x 605 mm snap grid frame work for false ceiling as per manufacturer instructions, with hangers of GI wire of suitable dia (up to 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long and 6mm thick Non asbestos fibre cement building boards, fixed to sheet suitably placed in false ceiling grid made of Aluminium/G.I./ M.S.as per specification and drawing and including dismantling old unservicable ceiling board including frame of any type and description, complete all as specified and directed.

Supply and fixing in repairs 7 feet 4 pipes pulley operated cloths drying system consisting of aluminium pipe of outer dia 22mm, inner dia 19.80mm, made up of detrin with rope guide mounted on channel pair of length 24 feet (distance between two pipes is adjustable) locking system to hide rope knot, channel to be mounted or fixed with self taping screws provided in kit. Rope will be HDPE double core of 4mm dia fixing to ceiling as specified and directed by Engr-in-Charge and minimum weight of one pipe shall not be less than 0.20kg/, minimum weight of rope shall not be less than 7700Gms/unit. Make Easydry or equivalent.

M&L polished Sadarahalli granite stone slab flooring 18-20 mm thick with grey cement slurry mixed with pigment to match the shade of the slab including 20mm thick screed bed in cement mortar 1:4 complete incl dismantling old stone slab complete all as specified and as directed.

M&L for 18 to 20mm thick polished sadarahalli granite tiles as in riser and dado of steps over 10mm thick cement mortar 1:4 incl dismantling old stone slab complete all as specified and as directed.

M&L for Preparation of old decorated plastered or unplastered surface of wall, Washing, rubbing down and stopping of distempered and painted surfaces and applying one coat oil bound distemper complete all as specified and as directed.

M&L for Preparation of old decorated surfaces of walls by Washing, rubbing down and stopping of distempered and painted surfaces,applying one coat of wall 1mm thick care putty and then applying two coats of premium oil bound distemper over one coat of primer as per manufauture instruction of required shade complete all as specified and directed.

Material and labour for Preparation of old plastered or unplastered surface of ceiling and applying one coat of white wash complete all as specified and directed.

Material and labour for Preparation of old decorated plastered or unplastered surface of wall, chajja, balcony, facia etc., brooming down or steel wire brushing down smoke soot, moulds mass, efflorescent, trading, oil, greasy spots and applying one coat of white wash complete all as specified and directed.

M&L for Preparation of old painted wooden surface of any description and applying one coats of synthetic enamel paint not otherwise described over 10 cm width or girth, complete all as specified and directed.

M&L for Preparation of old painted surfaces of steel and applying one coat of synthetic enamel paint over 10 cm width or girth, not other wise described complete all as specified and as directed.

M & L Providing one coat of synthetic enamel paint on steel surfaces n exc 10 cm width or girth including preparation of old steel surfaces all as specified and directed.

S&F Pre painted Coloured Galvalume roofing sheets 0.50 mm thick having Zinc aluminium alloy coating double ribbed trapezoidal profile steel sheet any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws and including dismantling of any type of old unserviceable sheets in roof coverings complete all as specified & directed.

S&F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified incl dismantling of old sheet complete all as specified and directed.

M&L MS Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 complete all as specified and directed.

M & L for 100 mm thick PCC 1:2:4 type B-2 (using 40 mm graded crushed stone agg) as in Hard standing etc. with , spike rolling ,or making impression of expanded metal, while the concrete is green including complete all as specified and directed.

Demolition cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed

M&L in 300mmx300mmx25mm thick pre-polished cement concrete chequered tile jointed in neat cement slurry and pointed in white or coloured cement to match the floor, complete, all as specified and directed.

M&L for screedbed or bedding layer of mortar 20mm thick for laying floor finishes in CM 1:6 complete all as specified and directed.

M&L for broken stone boulders hard core of guage n.exc 63mm deposited spread and leveled laid in layers n.exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

Complete removal of existing water proofing treatment of any description and in any position including PCC padding any thickness and cleaning, wire brushing, watering & removal of debris outside MOD land. NOTE :- Unit rate quoted shall also include for removal of PVC water storage tank and water pipe lines wherever existing carefully and refixing at the same or other position after completion of roof repair work

M&L for preparation of new/old any type of surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of floor guard paint over a coat of red oxide primer complete all as specified and directed.

M&L Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) complete all as specified and directed.

Roughening surfaces of old concrete floors by picking, sweeping clean and washing down with waters to remove dusts etc. complete all as specified and directed.

M&L for Brushing neat cement slurry with 3kg/sqm all as specified and directed.

M&L Cement concrete 1:2:4 type B1using 20 mm graded stone aggregate as in lintels, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, padding, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed .

M & L for 10 mm thick screed bed or bedding layer of mortar in cement mortar (1:4) for laying roof finish as padding finished with liquid WPC as per manufacturer instructions, complete all as specified and directed NOTE :- Integral WPC shall be measured and paid separately.

Apply oil bound bitumen primer @ 0.40 Litre / Sqm manufactured by the same agency as that of APP with density of 0.87 to 0.89 Kg / Litre at 25 degree Celsius on the prepared dry roof surface complete all as specified and as directed.

M&L APP polymeric membrane min weight 3.0kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric(wt not less than 150 gms/sqm laid on primed surfaces by torch application method complete all as specified and directed.

M&L for preparation of new surfaces of any description not otherwise described over 10cm width or girth and applying two coats of solar reflective aluminium paint @ 0.10 kg/sqm of membrane surfaces complete all as specified and directed.

M&L Petty repair to existing roof treatment by means of torching to old APP membrane, sealing to joints, bitumen sealent,incl aluminium paint etc complete all as specified and direcetd

Note for item No 134 :- The work shall be carried out by authorised and qualified applicators of the above mentioned manufacturer.

M&L Repair to leakage/seepage from the Nahani trap/ floor trap of kitchen/ bathroom/ washbasin of the upper Qtr, in any position at any height, complete including change of floor trap, PVC horinzontal pipe embeded in floor in bathroom or kitchen making good to the damaged portion of flooring, laying and matching of tiles in the existing flooring, complete all as specified and directed

M&L Repair to leakage/seepage from the wall/ door bend /door tee/ 'Y' junction/ 'T' Junction of soil pipe / waste pipe/ vent pipe of kitchen/ bathroom/WC of the upper Qtr or at the ground floor Qtr including change of any damaged soil waste pipes or fittings of any shape, specification and size, making good to the damaged portion of wall with brick work in cement mortar 1:6 or cement concrete 1:2:4 and plastering to wall in CM 1:4 and finished the surfaces matching to existing wall to avoid the leakage/ seepage at the site of work complete all as specified and directed.

Note for item No 136 & 137 :- (a) Find out main cause of leakage and take necessary steps to resolve / rectify. (b) Replace existing tiles in case leakage through NT/FT. (c) The rate also include provision of new NT/FT. (d) The unit rate is also deemed to be included for reqd bonding chemicals to arrest the leakage/seepage as directed by the manufacturer's specification. Make : M/s Sika Chemical, M/s Pidilite, M/s Dr Fixit

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/trenches bore of pipe 75 mm with PVC clamps and saddles including taking down old existing pipes and dismantling of cast iron/RCC/PVC drain pipes jointed in cement mortar and taking out from trenches or walls of any bore including fittings complete all as specified and as directed

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/trenches bore of pipe 110 mm with PVC clamps and saddles including taking down old existing pipes and dismantling of cast iron/RCC/PVC drain pipes jointed in cement mortar and taking out from trenches or walls of any bore including fittings complete all as specified and as directed

S & F in repairs PVC (SWR) bends of any radius with access door bore of pipe 75 mm complete all as specified and as directed.

S & F in repairs PVC (SWR) bends of any radius with access door bore of pipe 110 mm complete all as specified and as directed.

S & F in repairs PVC (SWR) bends of any radius with access door bore of pipe 150 mm complete all as specified and as directed.

S & F in repairs PVC (SWR) junction single (single T) equal or unequal with access door bore of pipe 75 mm complete all as specified and as directed.

S & F in repairs PVC (SWR) junction single (single T) equal or unequal with access door bore of pipe 110 mm complete all as specified and as directed.

S & F in repairs 125/ 110 mm bore PVC (SWR) floor trap plain with grating incl jointing with solvent cement complete all as specified and as directed.

S&F in repairs 0.56 mm thick Plain, Aluminium sheeting, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed) including dismantling of old one complete all as specified and directed.

Dismantling floor, floor hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises and Material and labour for Glazed digital / rustic finish ceramic coloured tiles 350x250mm/ 450 x 300 mm x 6-7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles on vertical surface such as skirting/ dado including 10mm thick 1:4 backing coat complete all as specified and directed.

Dismantling of floor, hearth or wall tiling incl cement mortar bedding (but not backing) and removing rubbish off from premises & M&L for ceramic coloured tiles of size 350mmx250mm/ 300mm X 450mmx7 to 8 mm thick, on vertical surfaces, set and jointed in neat cement slurry and pointed in coloured / white cement to match the tiles inc rendering 10mm thick in CM 1:4 on fair faces of brick work or concrete surfaces as in backing coat to receive wall tiles etc complete all as specified and directed.

Dismantling floor, floor hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises and supplying and fixing Joint free Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile of size n exc 0.18 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incuding screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar (1:6) complete all as specified and directed.

Dismantling floor, floor hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises and supplying and fixing Joint free Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile of size n exc 0.18 Sqm as in vertical surfaces over 10 mm thick rendering in cement mortar 1:4 finished including dismantling of existing tile and disposal to outside MD land complete all as specified and directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc.complete all as specified and as directed

M&L Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Grinding of existing mozaic/kota stone/tiles in wall/flooring including mirror polishing, cleaning and joints filling and apply white cement complete all as specified and directed.

M&L for cement plaster rendering 5mm thick in CM 1:3 on fair faces of brickwork or concrete surface as in ceiling finished even and smooth without using extra cement and taking down cement plaster on ceilings surface etc., hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises complete all as per specified and directed.

M&L preparation of newly plastered surfaces of ceiling and applying three coats of white washing on ceiling surfaces with smooth finish complete all as specified and directed.

Material and labour for Preparation of old decorated plastered or unplastered surface of wall, washing down, brooming down or steel wire brushing down smoke soot, moulds mass, efflorescent , trading, oil, greasy spots and applying one coat of cement based paint complete all as specified and as directed.

Material and labour for Preparation of old plastered surface and applying one coat of exterior weather proof emulsion complete all as specified and directed

Material and labour for Preparation of old plastered surface and applying two coats of exterior weather proof emulsion incl complete removal of existing treatment complete all as specified and directed

M&L Preparation of old Surfaces of any description over 10cm girth or width, not otherwise described applying one coat of plastic emulsion complete all as specified and directed.

M&L preparation of old surface of brick/stone/concrete etc of any description over 10cm girth or width, not otherwise described with one coat of synthetic enemel paint complete all as specified and directed

S&F in repair Aluminium composite panel of approved make 4 mm thick with 0.5 mm thick skin & PVDF coated approved shade for wall panelling in rectangular or circular shape. Main framing work to be done using 50mmx25mmx1.6mm tubular section of approved make . Stainless steel screw to be used to fix the ACP panel to be fixed to the main frame with industrial adhesive tape and panel groove to be sealed with weather proof silicon sealant suitable for glass/aluminium etc .complete all as specified and directed.

S&F in repair 3mm thick (solid thickness) compact polycarbonate sheet fixed in roof covering with and including aluminium strip and ss screws, joint sealed with epoxy complete all as specified and as directed.

S & F in repair vitreous china squatting pan 'Orissa pattern ' size 580 x 440mm white with integral foot rests incl connecting to 'P' or 'S' trap and to flush pipe anti syphonage pipe etc complete including provn of lime concerte bedding and making good to floor complete all as specified and as directed.

S&F in repairs Wash basin vitreous china (flat back or angle back type) size 580x400mm including taps waste chain and plug and porceline stopper but brackets including cutting for and pinning in ends of brackets or erecting stand with waste pipe, complete all as specified and directed.

S&F Wash hand basin table counter type 560x400x200mm vitreous china (white) with cantilever CI/Angle iron brackets embedded in concrete block, including long shank pillar tap, Brass chromium plated waste coupling 32mm bore, Waste pipe bottle trap, including taking down existing one complete all as specified and directed.

S&F in repairs 40 mm Waste coupling fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed one complete and all as specified and as directed.

S&F in repairs Vitreous China, half stall Urinal (back or corner wall type), complete including providing and fixing plugs, Urinal spreader, CP push cock, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and as directed

S&F in repairs PVC waste pipe 32/40mm bore for WHB, Urinal & Sink complete all as specified and as directed.

S&F Rimeless Single Piece WC with PP Soft Close slim Seat Cover, Hinges, Dual Flush Cistern Fitting, Fixing Accessories and Accessories Set, suitable Size, S/P Trap and including all fittings complete fixed in repair, all as specified and as directed.

S & F in repairs vitreous china wash down water closet (Pedestral pattern) EWC white incl plastic water closet seat cover and mild steel chromium plated or aluminium hinging device and connecting to 'P' or 'S' trap incl connecting flush pipe with flushing rim complete all as specified and as directed.

Supply and fixing in repairs plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device all as specified and directed.

Taking down & re fixing high or low level flushing cistren 10 ltrs capacity & connections to pipes & fixing of chain & pull or lever after cleaning inside of all dirt, scale formation, replacement of including rubber washers, syphon set, float valve, handle,fixing to wall clamp/bracket, stopping of leakage etc wherever required complete all as specified and as directed

S & F in repairs PVC low level flushing cistern 10 Lit capacity including necessary brackets incl connecting flush pipe etc and making good the disturbed surfaces complete all as specified and as directed.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 meter long flexible tube and ABS wall hook including taking down existing one complete all as specified and as directed.

M&L Petty repairs to leaking water in bib taps, pillar cock, stop cock, angle valve, concealed stop valve, bottle trap of any description by changing the PVC washers/ Sheet washers,spindle brass,jumper brass or any other minor accessories (incl taking down and refixing) complete all as specified and directed

S & F in repair bib tap standard of PTMT any colour screwed for iron pipe and fixed,15 mm bore (minimum weight 90gms) complete all as specified and as directed.

S&F in repairs of Stop Valve standard of PTMT any colour high pressure screwed for iron pipe and fixed.(Minimum weight 15mm-90gms) complete all as specified and as directed.

S&F in repairs of pillar tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-110gms) complete all as specified and as directed.

S & F in repairs 15 mm dia stop valves of cast copper alloy fancy type chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and as directed.

S&F in repair of Push tap any colour high pressure of PTMT screwed for iron pipe and fixed, (Minimum weight 15mm-47gms) complete all as specified and directed.

S&F in repair of CP Flush cock Push type any high pressure screwed for iron pipe and fixed, complete all as specified and directed.

S&F In repair 25 mm dia Concussive push button taps of cast copper alloy, screwed for iron pipe and fixed

S & F in repairs Bib taps cast copper alloy chromium plated fancy type screwed down screwed for iron pipe or for brass ferrule and fixed for 15 mm bore complete all as specified and as directed.

S & F in repairs pillar tap with capstan heads chromium plated fancy type screwed down high pressure with or without letter 'Hot' or 'Cold' with long screwed shanks and flynuts screwed for galvanised iron pipe and fixed complete for 15 mm bore complete all as specified and as directed.

S&F Angular stop cock, chromium plated valves high pressure screwed both ends iron pipe or for unioins 15mm dia, including taking existing one complete as directed.

S&F CP Concealed stop cock, Regular body with adjustable wall flange screwed down screwed for iron pipe 15mm bore. including taking down existing one complete all as specified and as directed.

S&F in repairs 2 way bib cock with wall flange PTMT screwed down screwed for iron pipe in repairs 15mm bore complete all as specified and as directed.

S&F in repairs Overhead Shower rose 125mm size (Brass Chrome Plated) complete all as specified and as directed.

S&F in repairs of Swivel Shower with arm of PTMT any colour and 195mm long bend of 45 degree with flange for fixed with 15mm pipe(Minimum weight15mm-90gms) complete all as specified and as directed.

Petty repair to internal/external water inlet water pipe line coming from over head tank to the quarter including socket,elbow,nipple ,with repair to water blockage , pipe line leakage, cleaning internally , removing the blockage including concealed water tubing etc of any height using scaffolding and making the water supply functional complete all as specified and directed.

Supply and fixing 15mm bore galvanized steel water tubing, medium grade with all fittings and fixed complete to walls and ceiling or laid in floors including taking up or down old steel tubing complete all as specified and directed.

Supply and fixing 20 mm bore galvanized steel water tubing, medium grade with all fittings and fixed complete to walls and ceiling or laid in floors including taking up or down old steel tubing complete all as specified and directed.

Supply and fixing 25 mm bore galvanized steel water tubing, medium grade with all fittings and fixed complete to walls and ceiling or laid in floors including taking up or down old steel tubing complete all as specified and directed.

Supply and fixing in repairs 20mm dia gun metal gate valve with iron wheel screwed both ends for iron pipe all as specified and directed.

S&F Rotational moulded polyethylene water storage tank of 500 Ltrs capacity cylinderical vertical with closed top including 3 Nos GI check nuts and tank nipple of 25mm bore for inlet and outlet, 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball hoisted and fixed in position all as specified in SSR part -I including taking down old unserviceable tank complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450 mm including taking down existing one complete all as specified and directed.

S&F in repairs Glass self assembly of 5.5mm thick and n exc 60cm length, 15cm wide with chromium plated bracket guard and fixed to wall with brackets complete all as specified and as directed

S&F Towel Ring stainless steel chromium plated round including taking down existing one complete all as specified and as directed.

S&F in repairs grating doom 125mm dia with waste hole of Chromium plated (Min wt 40 gms) complete all as specified and as directed.

S&F in repair Chromium plated soap dish including fixing arrangement complete all as specified and directed .

S & F in repair tubular towel rail brass chromium plated 20 mm dia 'D' type 60 cm long between flanges complete all as specified and as directed.

S & F in repair Toilet paper holder box type of vitreous china fixed to walls with chromium plated (CP) brass screws and complete all as specified and as directed.

S&F PVC body cabinet box mirror of size 350mm X 450mm X 100mm of PTMT alloy of approved pattern and design including taking down existing one complete all as specified and directed.

Cleaning of air/dust blokages in the internal water supply lines concealed or fixed on the wall or floor surfaces by dismantling the fitting such as taps, valves, unions etc to facilitate/stimulate clearance of blockages/airlocks and re fixing the dismantled items after clearance of blockage/airlocks including fiiitngs etc complete all as specified and as directed

Supplying and laying of 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and taking out old unsericeable steel/plastic/cpvc water tubing and connections complete all as specified and directed.

Supplying and laying of 25mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and taking out old unserviceable steel/plastic/cpvc water tubing and connections complete all as specified and directed.

Supplying and laying of 40mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and taking out old unserviceable steel/plastic/cpvc water tubing and connections complete all as specified and directed.

Supplying and fixing in repairs of 20mm outer dia Female Brass Threaded Adaptor (FTA/ FBTA CPVC complete all as specified.

Supplying and fixing in repairs of 25mm outer dia Female Brass Threaded Adaptor (FTA/ FBTA CPVC complete all as specified.

Supplying and fixing in repairs 20mm outer dia CPVC brass elbow all as specified and directed.

S&F Rotational moulded polyethylene water storage tank of 1000 Ltrs capacity cylinderical vertical with closed top including 3 Nos GI check nuts and tank nipple of 25mm bore for inlet and outlet, 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball hoisted and fixed in position all as specified in SSR part -I including taking down of old unserviceable tank complete all as specified and directed.

S & F in repairs PVC connection pipe 15 mm dia, 600 mm long with check nut and bolt with washer complete all as specified and as directed.

Petty repairs to refixing the existing Wash hand basin and Sinks made of stainless steel 1mm thick kitchen flat back with including fixing cantilever CI/Angle iron brackets embedded in concrete block including connecting waste coupling 32mm bore, including bedding, waste fitting, waste pipe in cement mortar to dwarf wall and connecting union to pipe, filling gap in white cement and all necessary fittings to fixed in repair (including taking down and refixing in same position) complete all as directed.

S&F in collapsible steel gates, top hung,consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets including dismantling old one , complete all as specified and directed.

M & L for 75 mm thick PCC type C1, 1:3:6 (20 mm graded stone aggregate) as in plinth protection finishing the surface even and smooth with using extra cement all as speecified and as directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

M&L Pre-cast PCC 1:3:6 type C1 (using 20 mm graded stone agg) cement concrete block masonry with solid blocks exc. 10cm in width and set in cement mortar 1:6 built in cement mortar of any description complete all as specified and as directed.

Extra for forming fair finished drain or channel 30cm inner girth all as specified.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

M&L for rendering 15mm thick in cement mortar (1:4) on brick or concrete surfaces of wall and finishing the surface even and smooth without using extra cement complete all specified and directed.

M&L preparation of newly plastered surfaces of wall and applying three coats of white washing on wall surfaces complete all as specified and directed.

Material and labour for Preparation of new plastered surfaces of wall and applying two coats of cement based paint over one coat of primer complete all as specified and as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed.

S&F in framed work as in doors or gates of angle tubes or other section with gusset plates, rails, braces,guard bar etc., complete, to be prepared for hanging or sliding with and including hinges or steel hanging door fittings (exclusive of steel sheeting or other covering) and hanging; also fastening and fixing Fe 410 -W (Gde- E- 250) quality-complete all as specified and directed.

S&F Welded steel wire fabric cut to length, bent to shape required and tying with and including annealed mild steel not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members not exceeding 4kg/sqm complete all as specified and directed.

M & L Providing two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces over 10 cm width or girth including preparation of new steel surfaces all as specified and directed.

M&L for welding in repairs exceeding 2.5cm in length and thickness of metal to be welded in exceeding 9mm but no exceeding 20mm thickness complete all as spcified and directed.

Running welding in repairs thickness exc 6 mm but n exc 9mm, complete all as specified and directed.

Dismantling posts or struts (wood, steel, or RCC) any section, any length n exc 5m including taking out embedded portion in concrete, brick work, masonry etc and all as specified and directed.

M&L for Cement concrete 1:3:6 type C2 (using 40 mm graded stone agg) as in foundation, filling and for mass concrete all as specified and directed

S & F MS angle iron Hand rails, fencing posts, flat iron including embeding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc., flat iron fillets (for securing wire mesh etc.) including necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Supply only of chain link fencing MS galvanised square wire mesh of any size, dia of wire 4mm including line wires, to any type of standard rails, straining bolts, etc complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc inlcuding provision of binding wire and dismantling of old fencing wire mesh of any type etc all as specified and directed.

S&F MS round bars 10 mm dia and over Fe 290 (Gde - E-165) cut to length bent to shape required including cranking, bending spirally, hooping for columns, hooking ends all as specified and directed.

S &F in repairs Mild steel screw bolts (machine made) dia of neck 16 to 20mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long, complete all as specified and directed.

Site clearance by Scraping of grass/wild growth/trees cutting n.exc 0.30m girth etc in soft/loose soil by manually/mechanically including removing of rubbish from the site to a distance exc, 250m but n. exc 500m and deposited where directed at a level not exc. 1.5m above the starting point, complete all as specified and as directed

Taking down and refixing precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade over sand cushion with grey cement and no pigment and including side kerb concrete, including removal and refixing all as specified and directed.

M&L for machine pressed pre polished precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80mm thickness, M-40 Grade with grey cement and pigment all as specified and directed.

M & L for Sand filling under floors or in foundations including watering and consolidation and all as specified and directed.

M&L PCC (1:4:8) type D2 using 40mm graded aggregate 75mm thick as in sub base of floor finished even and rough to receive top layer all as specified and directed and demolition of old concrete (un reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed.

M & L walling of random rubble, uncoursed, Bangalore type masonry well bonded bedded solidly hearted built in CM 1:6, extra over stone walling for hammer dressing to face stones and dressing of face beds and joints including demolition of old stone masonry of any description all as specified and directed.

Fixing only walling random rubble, uncoursed, Bangalore type masonry (except stone) well bonded bedded solidly hearted built in CM 1:6, extra over stone walling for hammer dressing to face stones and dressing of face beds and joints as specified, key pointing to random or polygonal rubble, uncoarsed or brought upto courses in CM 1:4 and including removal and refixing, built in cement mortar of any description as specified and directed. (Old stones shall be re-used)

Material and labour for keyed pointing in cement mortar 1:4 to random or polygonal rubble including racking out joints / points in cement mortar to squared rubble masonary coursed or un coursed etc complete, all as specified and directed.

Raking out joints/ pointing to random rubble or polygonal rubble uncoursed or brought up to courses with cement or cement lime mortar

S & F in repair concertina coil of 610mm dia (in stretched position) hot dip galvanised steel wire coated with CLR ante corrosive coating making diamond shape with the help of devotail clips (18 SWG) fixed over barbed with the angle iron the concertina coil is to be fixed with barbed wire at points where coil touched the bottom of barbed wire with the help of hog rings (14 SWG) complete,incl removal of old unserviceable coil of any description all as specified and directed.

S&F in repair galvanised two strand steel barbed wire 2.24 mm dia barbed wire with 2 mm barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provision of galvanised MS wire staples or steel pins etc as directed (each line wire to be measured)

Restraining and resecuring barbed wire including making good staples etc (each line wire to be measured) complete all as specified and directed.

M & L broken glass coping on top of walls in cement mortar 1:3 incl taking down old glass and removing the rubbish.

M&L Providing precast cement concrete louvres and jallies, 35mm thick (measured solid) set in CM 1:4, type B0 1:2:4 , faces are finished smooth complete all as specified and directed.

S&F MS Plates Fe 410 -W (Gde- E- 250) quality- A (plain or chequered) channels, square cut or notched (ordinary and counter sunk forming holes, without any attachment

S&F Rolled sections Fe 410 -W (Gde- E- 250) quality- A as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates

S&F 0.63mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed.

Material and labour for Providing 50mm thick cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in floor of SWT, surfaces finished even and smooth with using extra cement, laid to slope for further treatment with using integral water proofing compound and demolition of old Concrete (un reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed. Note : WPC shall be measured and paid separately).

Supply only liquid water proofing compound of approved make (ISI marked) all as specified and directed.

M&L Providing, cement concrete type B0 1:2:4 (12.5mm graded) in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed all as specified and directed.

M&L Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

M & L for precast cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) setting in CM 1:6 work for landings, cover slabs, manholes, chajjas, water troughs, manger shleves and similar articles with plain faces including demolition of old reinforced cement concrete of any description and in any position complete all as specified and directed.

M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L PCC (1:4:8) type D2 using 40mm graded aggregate 75mm thick as in sub base of floor finished even and rough to receive top layer complete all as specified and directed

Excavation in trenches not exceeding 1.50 m wide and not exceeding 1.50 m deep along the existing sewage line carefully for placing taking out and getting out in soft/loose of soil complete all as specified and directed.

Excavation in trenches exceeding 1.50 m deep and not exceeding 3.00 m deep along the existing sewage line carefully for placing taking out and getting out in soft/loose of soil complete all as specified and directed.

Demolition and breaking up 150mm dia drain pipes (salt glazed ware, AC or reinforced concrete) set in cement mortar complete all as specified and directed.

Demolition and breaking up 200mm dia drain pipes (salt glazed ware, AC or reinforced concrete) set in cement mortar complete all as specified and directed.

M & L salt glazed stone ware drain pipes of internal dia 150 mm bore grade 'A' laid in trenches and jointed complete all as specified and as directed.

M & L salt glazed stone ware drain pipes of internal dia 200 mm bore grade 'A' laid in trenches and jointed in cement mortar complete all as specified and as directed.

M&L for concrete bed to drain pipe including packing under and haunching against the sides of drain pipe after they are laid and tested in PCC 1:3:6 type C-2 for 150mm dia drain pipe complete all as specified and directed

M&L for concrete bed to drain pipe including packing under and haunching against the sides of drain pipe after they are laid and tested in PCC 1:3:6 type C-2 for 200mm dia drain pipe complete all as specified and directed

Returning and filling soil in layers not exceeding 25cm thick each layer including spreading, leveling, watering and well ramming all as speicified and directed.

Removal of surplus excavated material to a distance not exc 50 m and deposited where directed at a level not exc 1.50 m above starting point all as specified and directed.

Cutting into existing manholes for connecting new drains pipe of 150 mm dia, making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate, surfaces smooth finished and reforming benching as required complete all as specified and as directed.

Cutting into existing manholes for connecting new drains pipe of 200 mm dia, making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate, surfaces smooth finished and reforming benching as required complete all as specified and as directed.

Punchuring and necessary repairs to existing SGSW pipe of 150mm dia for clearing blockages and sealing with piece of pipe, covering the entire area with cement concrete PCC 1:3:6 type C1 to avoid unhygenic condition and concreting around the pipe including necessary excavation and earth work in any type of soil, complete all as specified and directed.

Punchuring and necessary repairs to existing SGSW pipe of 200mm dia for clearing blockages and sealing with piece of pipe, covering the entire area with cement concrete PCC 1:3:6 type C1 to avoid unhygenic condition and concreting around the pipe including necessary excavation complete all as specified. Note for item No 275 & 276 : Rate quoted deemed to include necessary excavation and earth work in any type of soil, returning filling complete all as specified and directed.

M&L Cleaning/ clearing of sewage line (including manholes) 150 mm to 300 mm dia main line from 1st manhole onwards bore of any description, underground at any depth, removing any type of blockage including desludging, descaling & decoking of drain as well as manholes with combined high pressure water jetting cum suction (vacuum) type machine mounted on LCV/HCV /LMV/HMV and having facilities of high pressure vacuum and provn of hydraulic through high pressure thermo plastic fiber based water jetting hose and conical round shape nozzle pipe and flushing after cleaning including removing the same out side MD land and deposit where the place marked by the local municipality, complete all as directed.

Attending day to day complaints of different type of sewage work such as removing blockage of WCs, floor traps, Nahani traps, Gully traps, CI/PVC pipes all types any size, any height top to bottom including junction etc complete all as specified and directed.

Cleaning of blockage from nahani traps of bathroom/kitchen/Urinal/toilet in ground floor and upper floors all types any size, any height by taking out mud/sand incl taking out lid and re-fixing the same complete all as specified and as directed.

Cleaning of blockage from Gully trap to 1st manholes in ground floors, all types any size, any location by taking out mud/sand incl taking out lid and re-fixing the same complete all as specified and as directed.

(a) Cutting and filling shall be cleared of shrubs, vegetation, grass bush, weed, trees and sapling not exceeding 30 cm in girth, measured at a height of two metre above ground level. Cutting the grass/felling of trees shall include digging out roots up to 60 cm below the ground level or 14 cm below the formation level, whichever is lower. All holes and hollows formed in the ground digging out of roots shall be made good carefully by filled up with moorum/red bajri well rammed and levelled.

(b) Safaiwala shall report to concerned JE /AGE in service centre B&R daily including Sunday and holiday and get the job card for carrying out the work. The Job card shall be returned to concerned JE/AGE duly signed by the users as a token of completion of job.

(c) Cleaning, removal of silts/wastage of organic or inorganic materials of Sewage line of 100mm to 450mm bore up to 1st manhole, in between manholes, GT Chamber, etc to maintain sewage system functional all days including Sundays and holidays along with necessary T&P i.e flexible rods, cleaning pumps and safety kits etc.

(d) The complaints to be rectified within SIX hours on same day. In case of delay in rectification of complaint for more than Six hours, the penalty will be levied @ Rs.100.00 Per complaint/ day.

(e) In case the nature of job is such that the work cannot be completed within a period of 6 hrs then the same shall be brought to the notice of the GE/Engr-in-Charge and the period for the completion of the complaint shall be decided by the GE/Engr-in-Charge.

M&L Cleaning and Removing silt, grit , mud and other materials from covered drain in foul condition including removing materials from the site to outside MD land including necessary removing cover slabs and replacing after cleaning area including making good any damages complete all as specified and as directed.

Note :- The unit rate is deemed to be included for Removing of accumulated earth at sides of drain of any width and depth up to 30 cm. cleaning/cutting the grass around 1 m from drain (both sides) and removing the grass waste to outside MD land. Cutting and filling shall be cleared of shrubs, vegetation, grass bush, weed, trees and sapling not exceeding 30 cm in girth, measured at a height of two metre above ground level . Cutting the grass/felling of trees shall include digging out roots up to 60 cm below the ground level or 14 cm below the formation level, whichever is lower. All holes and hollows formed in the ground digging out of roots shall be carefully filled up with moorum/red bajri well rammed and levelled.

Taking out/pumping contaiminated sewage water/ sludge from septic tank/soakage well/ incl inlet/outlet chamber after plugin incoming sewage line suction (vaccum) type machine mounted on LMV/HMV and facility of high pressure vaccum and removing and dumping off the same in tank to a place out side contonment at the place marked for the purpose by local municipality or the authority controling the area as directed. Note :- Contractor is advised to ascertain the suitable place earmarked for disposal of sludge/sewage water from local municipality or area controling authority before quoting their rates. Disposal of waste at suitable place shall be sole responsibility of contractor and no representation or objection in this regard shall be entertained at any later stage.

Cleaning of manholes any size and not exc 1.5m depth including lifting, removing sludge, water with using mechanical instrument and cleaning with water including cutting grass, vegetation and bushes to a width of 60cm all alround manholes complete all as specified and directed.

Cleaning of manholes any size and exc 1.5m depth including lifting, removing sludge, water and cleaning with water using mechanical instrument including cutting grass, vegetation and bushes to a width of 60cm all alround manholes complete all as specified and directed. Note : the sludge obtained while cleaning shall be removed from the site to outside of MOD land. The rates quoted for items shall include the above provns also.

M & L for cement concrete 1:2:4 type B1(using 20 mm graded crushed stone aggregate) as in surface channel of drain, benching in manhole & coping finished even and smooth with using extra cement complete all as specified and as directed.

M&L For PCC (1:4:8) type D2 using 40 mm graded stone aggregate as in foundation of manholes, drains, walls and similar works etc, ncluding demolition existing cement concrete in any description and in any position,complete all as specified and directed.

Note :- An amount of Rs 1,27,680.00 on account of credit schedule for schedule 'A' part II shall be deducted from the total amount of BOQ to arrive at the contract sum.

Please Enable Macros to View BoQ information