SPECIAL REPAIR TO RETAINING WALL NEAR BLDG NO P-38 AND BLDG NO P-85 NEAR ACRR BLDG AT INS UTKROSH UNDER GE MINNIE BAY PORT BLAIR

Amount

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete as specified and directed by Engineer in Charge.

Demolation of precast concrete work/ precast concrete block built in cement mortar including all quoins arches pillers etc complete as specified and directed by Engineer in Charge.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc.,complete as specified and directed by Engineer in Charge.

Taking down cement plaster on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water, etc complete as specified and directed by Engineer in Charge.

Demolartion of cement concrete (unreinforced) including tiles and pavings n exc 15cm thickness (below or above ground level) complete as specified and directed by Engineer in Charge.

Taking up or down old/choked water tubing 25 or 32 mm bore with fittings from trenches/walls complete as specified and directed by Engineer in Charge.

Taking down existing chowkhats or frames exc 1.5 sq. m but n exc 4 sq. m each without taking off shutters from the frames complete as specified and directed by Engineer in Charge.

Taking down existing chowkhats or frames exc 1.5 sqm each with shutters(without taking off shutters from the frames) complete as specified and directed by Engineer in Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete as specified and directed by Engineer in Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete as specified and directed by Engineer in Charge.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete as specified and directed by Engineer in Charge.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete as specified and directed by Engineer in Charge.

S&F aluminium flat iron work in wind ties scrow as directed incl all necessary drilling,bolting, riviting & etc complete all as specified

S&F in PVC (SWR) 110mm dia pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors or on wall including solvent complete as specified and directed by Engineer in Charge.

S&F in PVC (SWR) 75 mm dia pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors or on wall including solvent complete as specified and directed by Engineer in Charge.

S&F PVC (SWR) bends 100 mm dia etc complete as specified and directed by Engineer in Charge.

S&F PVC (SWR) bends 75 mm dia etc complete as specified and directed by Engineer in Charge.

M&L for external rendering 5 mm thick in CM(1:4) with water proofing compound ( water proofing compound shall be used as per manufacturers instructions) over a coat of 10 mm thick in CM(1:6) over brick or concrete surfaces finished even and fair surfaces complete as specified and directed by Engineer in Charge. [Note : Supply of WPC will be measured seperately]

M&L for rendering 10 mm thick on fair faces of bricks/concrete surface in CM(1:6) finished even and smooth without using extra cement complete as specified and directed by Engineer in Charge.

M&L for rendering to ceiling in 5 mm thick on fair faces of concrete surface in CM(1:3) finished even and smooth without using extra cement complete as specified and directed by Engineer in Charge.

Supply and water proofing compound conforming to IS-2645 1975complete as specified and directed by Engineer in Charge.

M&L for preparation of new surfaces of wall and applying two coats of oil bound distemper over a coat of primer complete all as specified and as directed by Engr-in-Charge

M&L for preparation of new surfaces of ceiling and applying two coats of oil bound distemper over a coat of primer complete all as specified and as directed by Engr-in-Charge

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

S&F Aluminium anodised (minimum anodisation is 50 microns) Door/ window /ventilator/partition frames and shutters (02 Nos glazed & gauzed), side hung type, without sash bars, standard aluminium grills,aluminium snap beading,screws,handles,locking arrangements etc, complete with standard aluminium sections, complete all as specified and as directed by Engineer-in-charge. (Note:-Weight of various Aluminium sections handles and locking arrangements shall only be considered for measurement for payment.However cost of rubber packing given in the item shall be deemed to be included in the rate quoted. Glass panels, prelaminated particle boards, glass & aluminium wire cloth as application will be measured and paid separately as supplied only).

Supply only 5 mm thick sheet Figured glass and glazing with rubber packing around the glass , in squares n exc 0.5 sq. m in each pane complete all as specified.

Supply only Aluminium alloy wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.40 mm complete all as specified

M&L for prepaing new or previously untreated Surfaces of any description, over 10 cm in width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed by Engineer in charge. [Note:-Rate quoted including of scaffolding at any height]

M&L complete removal existing wall surface applying two coat of oil bound distemper over a coat of alkali resistant priming paint including preparation of new plastered surfaces of wall complete all as specified and directed by Engineer-in-charge.

M&L for applying one coat of acrylic emulsion weather coat premium quality antifungal exterior emulsion to old painted surface of wall including preparation complete as specified and directed by Engineer in Charge.

S&F in repairs aluminium anodised snap grid false ceiling of standared aluminium section of size 38mm x 25mm x 24mm , weight 0.363 Kg/RM main/cross tees of size 38.5mm x 25mm x 1.4mm weight 0.24 Kg/RM, Grid size n.Exc 610mm x 610mm suspended false ceiling with 4mm dia Gi wire interval n exc 600mm centre to centre for main & cross tees fixed to roof slab , roof truss fixed with suitable size MS hook and fastening bolts etc including e board classic 4 mm thick oceanic sheet of size n exc 610mm x 610mm size fixed in ceiling with clips to aluminium snap grid and preparation of new surface and appling two coats of oil bound distemper over one coat of primer complete all as specified.

M&L for in framed work as in brackts , angles , or tees with web and flanges cut to shape , drilled ans counter sunk for scrow , incl bending and welding angles as necessary gusset plates, rails braces, etc. covering and fixing complete all as specified

M&L for Mild steel as in Stairs (framed) including stringers, treades, landing, balusters, hand rails etc. including cleats, brackets, etc Fe-410-w(Gde-E-250) quality-A complete as specified and directed by Engineer in Charge.

S&F for Rolled sections/tubular Mild Steel pipes as in cross beams, hip and jack rafters, vertical posts, purlins where connected to common rafters fixed with angle cleats or similar work including welding and all necessery works complete all as specified (Fe-410-W-(Gde-E-250)quality A complete as specified and directed by Engineer in Charge. [Note:-The cost of Scaffolding as required shall deemed to be included in this quoted rate].

S&F Mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment including necessary welding complete as specified and directed by Engineer in Charge.

M&L Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed ded CM(1:6) complete as specified and directed by Engineer in Charge.

M&L Glazed ceramic tiles in vertical surface 450x 300x 6mm to 7mm thick on vertical surfaces as in skirting , dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 10 mm thick bedding layer in cement mortar (1:3) including necessary cutting as per site requirement complete all as specified and directed by Engineer-in-charge.

M&L for Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over a screed bed of 10 mm thick in CM (1:4) complete as specified and directed by Engineer in Charge.

M& L Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over a15 mm thick screed of CM (1:6) complete as specified and directed by Engineer in Charge.

M&L for Chequered cement concrete tiles 300mm x 300mm x 25mm thick, set, jointed and pointed in neat cement slurry in floors/ vertical surfaces / rises /bullnosed treads with grey cement including screed bed or bedding layer of motar 15 mm thick in cement mortar 1:6 complete as specified and directed by Engineer in Charge.

Supplying and laying 25mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on wall/ceiling or laying in floor complete as specified and directed by Engineer in Charge.

S&F 25mm dia CPVC Brass Elbow outer dia complete as specified and directed by Engineer in Charge.

S&F 25mm dia CPVC Brass Tee CPVC pipe outer dia complete as specified and directed by Engineer in Charge.

S&F 25mm dia CPVC Male brass threaded adopter CPVC pipe complete as specified and directed by Engineer in Charge.

S&F 25mm dia CPVC tank adapter CPVC pipe complete as specified and directed by Engineer in Charge.

S&F 25mm dia CPVC union complete as specified and directed by Engineer in Charge.

S&F 25mm dia CPVC ball valve complete as specified and directed by Engineer in Charge.

S&F 25mm PP-R Gate valve brass insert complete as specified and directed by Engineer in Charge.

S&F in repair for 1000 Litres rotational moulded polyethylene water storage tanks ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including tank cover and dismantling of old one complete as specified and directed by Engineer in Charge.

S&F in repair CP towel rail, 20mm dia, 60 mm long fixed with CP screws and wood cleats / rowel plug in wall ,complete as specified and directed by Engineer in Charge.

S&F in repair Pillar taps, cast copper alloy, chromium plated, fancy type heavy duty , 15 mm dia , with capstan head ,screwed down high pressure, with long screwed shanks and fly nuts screwed for iron pipe and fixed complete as specified and directed by Engineer in Charge.

S&F in repair 15mm dia Bib taps, cast copper alloy heavy duty,chromium plated , fancytype screwed down iron pipe and fixed etc complete as specified and directed by Engineer in Charge.

S&F in repairs 15 mm dia bore cast copper alloy chromium plated angle cock/stop cock with long shank and cup screwed down high pressure with capstan head, screwed both ends for iron pipes or for union and fixed complete as specified and directed by Engineer in Charge.

S&F in repairs 15mm dia two way bib taps, cast copper alloy,chromium plated, fancy type,screwed down for iron pipe and fixed etc complete as specified and directed by Engineer in Charge.

S&F in repairs 32/40mm dia PVC flexible Waste Pipe, 750mm long fixed to wash hasnd basin or sink complete as specified and directed by Engineer in Charge.

S & f in repairs PVC connection 15mm size with CP brass nuts of length 600mm complete all as apecified and as directed by Engineer in Charge

S & F in repairs 10 Liters capacity, PVC Valve less, Syphonic action type, low level flushing cistern, white, with inlet ball valve, float, handle, flush pipe of polyethylene of low or high density of PVC, 32mm dia including brackets and connections to pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repairs vitreous china ware wash hand basin, white flat back of size 550mmx440mm including 15mm bore chromium plated copper alloy pillar tap 32mm brass chromium plated waste fittings with long screw shanks and fly nuts flange end bedded in red led cement and other end fixed rubber plug with rings including CI Brackets cutting for and pinning in ends of brackets or erecting strand etc complete all as specified and as directed by Engr-in-Charge.

S & F Vitreous China wash down water closet pan ( Pedestal pattern) EWC white in clour with and incl plastoic water seat and cover white closed pattern with flat bottom and cover and MS chromium plated hinging device incl connection to outgoing pipe and flushing pipe complete as specified and directed by Engineer in Charge.

S & F Vitreous China Counter top Wash basin, white colour of size 550mm including fixing on granite slab, including pillar tap 15mm bore Chromium plated cast copper alloy with capstan heads, 32mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts & 15mm PVC connection pipe complete as specified and directed by Engineer in Charge.

S & F in repairs vitreous chaina urinal, half stall long type of size 315 x 375x 620 mm colour white incl urinal spearder of PTMT of any colour for fixing with 15 mm dia pipe (minium weight 60 gms) complete as specified and directed by Engineer in Charge.

S & F soild PVC door frame of size 50 mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube in opening complete as specified and directed by Engineer in Charge.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of rudraksh colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification complete all as specified and as directed by Engr-in-Charge

S & F 75mm size medium weight butt Hinges, cold rolled, stainless steel including fixtures complete as specified and directed by Engineer in Charge.

S & F extruded aluminium alloy handle fabricated type anodised 100mm long complete as specified and directed by Engineer in Charge.

S & F in aluminium anodised barrel tower bolt of size 150mm size of extruded section complete as specified and directed by Engineer in Charge.

M & L for CRS grade TMT bars 10mm dia and over as in reinforcement cut to length, bent to shape required including cranking hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securuing clips complete as specified and directed by Engineer in Charge.

Ditto as per item No 68 as above but (6mm to 8mm dia for Stirrups) complete as specified and directed by Engineer in Charge.

M & L for Reinforced cement concrete 1:2:4 (Nominal Mix) in Chajjas, slabs and similar type of work including formwork complete as specified and directed by Engineer in Charge.

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete as specified and directed by Engineer in Charge.

M & L precast cement concrete block masonry with PCC solid blocks in 1:3:6 type C1 using 20mm graded stone aggregates, exc 10cm in width and set in CM 1:4 complete as specified and directed by Engineer in Charge.

M & L for 75mm thick Plain Cement Concrete 1:3:6 type C1 using 20mm graded stone aggregate as in plinth protection and finished even and smooth with using extra cement laid in panels including joints complete all as specified and directed

S & F 18 to 20mm thick HDF board including decorative laminations on bothsides, on side plain and another side decroative fixed to frame work complete as specified and directed by Engineer in Charge.

M & L first class hard wood for wooden beading , cupboards / shelves / wardroble / wall paneling exc 6 & not exc 13 Sqm complete as specified and directed by Engineer in Charge.

S & F 100 mm brass handles, cast type, polished bright complete as specified and directed by Engineer in Charge.

S & F 100 mm size hasp and staple, stable , safty tyoe, brass with mild steel hinges pin including bolt to hinge plate with scrows complete as specified and directed by Engineer in Charge.

S & F continuous (piano)hinges, mild steel, bright finish or electrogalvanished and with of flaps 30mm (When open) complete as specified and directed by Engineer in Charge.

S & F Teak wood lipping frame 6mm thick for 18/19mm width fixed with nails / screws complete as specified and directed by Engineer in Charge.

S & F 2nd class hard wood for plain, solid, straight, chowkats and frames, wrought, framed reabeated the soild rounded or chamfered put together with glue pinned at joints complete as specified and directed by Engineer in Charge.

S & F brass Auto closing Magnet catch for cup boards and skirting plate complete as specified and directed by Engineer in Charge.

Material and labour for APP modified waterproofing treatment over existing RCC roof slab with following specification including brushing off the surface to receive the treatment obtain the required surface and then providing 10mm screed bed with water proofing compound with required slope complete as directed :- Note : Rendering and WPC shall be measured and paid separately under relevant item of this schedule (a) Applying bituminous primer @ 1.2 kg/Sqm on the prepared dry roof surface. (b) Laying 4mm thick APP membrane Plain finish weight not less than 3 to 4 kg per sqm by torch application with minimum 10cm side lap and 15cm end lap.(c) Applying bituminous primer @ 1.2 kg/Sqm and applying one coat of bituminous aluminium paint at the rate of 0.3kg/sqm Note : The laying of membrane shall be got done through an authorized applicator of manufacturer of APP membrane.

Demolition of RCC work of any description and any position complete as specified and directed by Engineer in Charge.

Excavating over areas not exceeding 1.5m deep and getting out in soft / loose soil complete as specified and directed by Engineer in Charge.

Excavating over areas exceeding 1.5m deep and not exceeding 3m deep and getting out in soft / loose soil complete as specified and directed by Engineer in Charge.

Material and labour for Plain cement concrete 1:3:6 mix, Type C2 (using 40 mm graded stone aggregate) in foundation, filling and mass concrete including formwork complete as specified and directed by Engineer in Charge.

M&L Reinforced Cement Concrete M-30 Design mix using 20mm graded stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams etc., and mass concrete including formwork complete as specified and directed by Engineer in Charge.

M&L Reinforced Cement Concrete M-30 Design mix using 20mm graded stone aggregate as in retaining walls, basement walls and the like any thickness above top of footing including attached pillasters and butresses including formwork complete as specified and directed by Engineer in Charge.

M&L CRS grade TMT bars 10mm dia and over as reinforcement cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete as specified and directed by Engineer in Charge.

M&L boulder filling dry, of broken stones or boulders of gauge 80 to 150mm handpacked tightly behind weep holes complete as specified and directed by Engineer in Charge.

M & L 110 mm dia bore 3 layer PPR SDR 7.4 (PN16) UV stabiized fixed as weep holes in retaining walls complete as specified and directed by Engineer in Charge.

Material and labour for back filling of retaining wall using approved earth obtained from excavation and spreading in layers n.exc 30cm thick each layer complete as specified and directed by Engineer in Charge.

Exavation in post holes in soft / loose soil not exc. 0.5 cum and removing surplus soil to a distance not exc 50 mtr and making good the surface complete as specified and directed by Engineer in Charge.

Excavation in trenches not exceeding 1.5M wide and not exceeding 1.5m depth for foundation, etc, and getting out in soft / loose soil complete as specified and directed by Engineer in Charge.

Material and labour for Plain cement concrete type D2 1:4:8 (using 40mm graded granite stone aggregate) in foundation filing and mass concrete including formwork

M/L precast cement concrete block masonry with solid block type C1 1:3:6 (20 mm graded aggregate ) exc 10cm in width and setting in CM 1:6 in repair

M&L for mild steel framed work such as posts , railing and fancing work and similar work to conforming to Fe-410-0 or Fe-310.0 complete

M&L Mild steel framed work as in door and gates of angle or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering door etc to be prepared for handing or sliding with and including either hooks and hinges or steel hanging or sliding with or including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering running rails and guides) and handing also fastening and fixing complete of grade FE-41W (Gde E-250) quality A in repair

S&F in repair PVC coated chain link MS galvnized fencing mess of size 50x50mm , having 3mm dia wire with minimum 1mm thick PVC coating [5mm overall dia] complete fixed to any type of standards, rails, straining bolts , etc all as specified. (Note : The supply only of MS flat iron, Rod & MS bolts shall be measured & paid under relevent items of Schedule)

Supply only MS bars 10mm dia for support to chain link fencing.

Supply only flat iron as in fillets fort securing wiremess including necessary drilling holes for bolts and welding confirming to Fe-310-0

Supply only screw bolts 10mm dia machine made hexagonal or square head at one end screwed the other or screwed both ends to be fitted with washers & one hexagonal or square not exc 150mm long.

Material and labour for preparing new steel or iron surfaces of any description over 10 cm width or girth and applying two coated of synthetic enamel paint over a coat of red oxide zinc chrome primer.

M&L Preparing New steel or iron surfaces of any description N.exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer.

Returning, filling in soft / loose soil, including, spreading, levelling, watering, and well ramming in layers, not exc 25 cm.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point

S&F Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) of grade FE-410-w (Gde-E250) quality A

M & L for taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, pendants, regulators sockets, laminated sheet & box etc, removing materials and making good disturbed surfaces of walls, floors, etc all as specified and directed by Engineer-in-Charge.

M & L point wiring with 1.5 Sq.mm (nominal area) PVC unsheathed multi strandard copper conductor PVC insulated 1100 volt FRLSH grade multistranded cable drawn through and including PVC casing capping/conduit ISI marked minimum 20mm size and its accessories complete along with 1.5 Sqmm cable but in green color as continuous earthing wire and connecting to common earth dolly completely concealed ,surface, in walls/ceiling/roofs with and including 1.2mm thick Mild Steel sheet terminal boxes duly fabricated flush mounting in the wall for mounting switches, switch socket combinations fan regulators etc., as required with 3 mm thick plastic laminated sheet top cover all as specified and directed by Engineer-in-Charge. for the following:-

One light / fan point controlled by one 05amps switch all as specified and directed by Engineer-in-Charge.

One 5 Amps plug point independent board controlled by one switch all as specified and directed by Engineer-in-Charge.

One three pin switch socket 5 Amps plug point on same board all as specified and directed by Engineer-in-Charge.

All as per item No 109.00 here in before but with 2.5 Sqmm single core multi stranded FRLSH copper conductor for one three pin socket 5amps on independent board including continuous earth wire PVC insulated 2.5 Sqmm copper solid conductor to common earth dolly all as specified and directed by Engineer-in-Charge.

All as per item No 109.00 here in before but with 4 Sqmm single core multi stranded copper conductor for one three pin socket 5 Amps on independent board including continuous earth wire PVC insulated 4 Sqmm copper solid conductor to common earth dolly all as specified and directed by Engineer-in-Charge.

S & F socket outlet 2/3 pin 5 Amps 240 volts flush type all as specified and directed by Engineer-in-Charge.

S & F socket outlet 3 pin 5/15 Amps 240 volts flush type all as specified and directed by Engineer-in-Charge.

S & F switches 5/6 Amps 240 volts flush type all as specified and directed by Engineer-in-Charge.

S & F switches 15/16 Amps 240 volts flush type all as specified and directed by Engineer-in-Charge.

S & F ceiling rose surface type bakelite 65 x 50 mm with three terminals with ISI marked all as specified and directed by Engineer-in-Charge.

Supply and fix in replacement LED tube light fitting, 1x20 w, 230v .Surface and wall mounted LED batten, extruded aluminum housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver. Flicker free, high efficiency and robust industrial batten family suitable for Surface, Wall and Conduit mounting. The product family offers dimmable and connected batten option & connecting up with twin core twisted flexible copper conductor cable with suitable size all as specified and directed by Engineer-in-Charge.

Supply and fix in replacement BLDC ceiling fans, complete with three blade, down rod, accessories 230V, 1200mm sweep, with Squirrel cage induction motor all as specified and directed by Engineer-in-Charge. Note : Old unserviceable fans shall be handed over to AGE EM Store yard and necessary receipt voucher shall be submitted to GE for payment.

Supply and fix in replacement exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers all as specified and directed by Engineer-in-Charge. Note : Old unserviceable fans shall be handed over to AGE EM Store yard and necessary receipt voucher shall be submitted to GE for payment.

Supply and fix in replacement of Building light fitting LED type, 35 Watts 240 Volts luminous shall be more than 2000 lumen, efficiency not less than 100 lm/Watt , and accessories complete mounted on 25/40 mm dia light grade GI pipe bracket 1.0 mtr long bent to shape, mounted on wall, connection all as specified and directed by Engineer-in-Charge.

S&F DB SPN 8 way with category of protection double door type IP-42 factory made with tinned copper bus bar to be fixed in wall suitable for MCBs, all as specified and directed by Engineer-in-Charge.

S&F MCB DP 32 Amps working on 415 volts 50 Hz AC supply,10 KA "C" series all as specified and directed by Engineer-in-Charge.

supply and fix MCB Single Pole 6 to 32 Amps working on 240 volts 50 Hz AC supply,10 KA "C" series all as specified and directed by Engr-in-Charge.

M&L for Sub main wiring complete with 2 runs of 1.5 sqmm , single core , multi stranded copper conductor FRLSH PVC insulated and sheathed cable 1100 Volts grade , drawn in PVC Casing Capping in surface /PVC conduit in concealed/surface (as required) along walls roofs etc including 1.5 sqmm size PVC insulated unsheathed copper earth continuity conductor to common earth and connecting to earth dolly all as specified and directed by Engineer-in-Charge. Note:- all three wire/cable(phase, neutral and earth) should be run through for each individual circuit from the DBs. Note. Two runs of cable and one run of earth conductor be measured as single unit length)

M&L for Sub main wiring complete with 2runs of 2.5 sqmm , single core , multi stranded copper conductor FRLSH PVC insulated and sheathed cable 1100 Volts grade , drawn in PVC Casing Capping in surface /PVC conduit in concealed/surface (as required) along walls roofs etc including 2.5 sqmm size PVC insulated unsheathed FRLSH copper earth continuity conductor to common earth and connecting to earth dolly all as specified and directed by Engineer-in-Charge. Note:- all three wire/cable(phase, neutral and earth) should be run through for each individual circuit from the DBs. Two runs of cable and one run of earth conductor shall be measured as single unit length)

M&L for Sub main wiring complete with 2runs of 4.0 sqmm , single core , multi stranded copper conductor FRLSH PVC insulated and sheathed cable 1100 Volts grade , drawn in PVC Casing Capping in surface /PVC conduit in concealed/surface (as required) along walls roofs etc including 4.0 sqmm size PVC insulated unsheathed FRLSH copper earth continuity conductor to common earth and connecting to earth dolly all as specified and directed by Engineer-in-Charge. Note:- all three wire/cable(phase, neutral and earth) should be run through for each individual circuit from the DBs. Two runs of cable and one run of earth conductor shall be measured as single unit length)

S&F in replacement of sheet metal enclosure with socket plug top, single pole and neutral enclosure with two pin earth plug and socket complete with one MCB SP of capacity 20 to 32 Amps all as specified and directed by Engineer-in-Charge.

Supply and install hi wall split units indoor/outdoor complete with cordless remote control unit and with in-built air ioniser and Plasma filter for better indoor air quality with minimum 5 star rating and EER 3.2 of capacity 1.5 TR including necessary copper tubes and drains duly insulated all as specified and directed by Engineer-in-Charge. Note : Old unserviceable Split AC shall be handed over to AGE EM Store yard and necessary receipt voucher shall be submitted to GE for payment.

M/S ISLAND REALCON INDIA PVT. LTD

M/s Sriya Enterprises

M/s Ramesh Lal

DEEPAK AGENCIES

Nirman Construction Company