PROVN OF 02 X TOILETS AND 01 X BATHROOM FOR STN MASJID PROVN OF ALUMINIUM PARTITION WITH FALSE CEILING IN CERTAIN UNIT PROVN OF PARKING SHED AT NEAR OLD CIRCLE PROVN OF STORAGE SHED FOR CERTAIN UNIT PROVN OF 02 X PARKING SHED IN FRONT OF OTM BLDG NO

Amount

SCHEDULE 'A' PART-I (B/R WORKS) Taking down cement plaster on brick or concrete surfaces incl racking out joints, hacking for key, scrubbing down with water etc. all as specified and directed.

Dismantling of floor, hearth or wall tiling incl cement mortar bedding (but not backing) removing tiles from site and rubbish off the premises complete all as specified and directed.

Dismantling stone slabs and tiles, laid, bedded and pointed in any mortar of any description or thickness in floors, aprons etc complete all as specified and directed.

Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillars etc complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil Complete all as specified and as directed

M&L for excavating over areas not exceeding 1.5 metre deep and getting out in soft/loose soil complete all as specified and directed.

M&L for excavating in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth in soft/loose soil complete all as specified and directed.

M&L for returning filling in including spreading, leveling, watering and well ramming in layer not exceeding 25 cm for soft/loose soil complete all as specified and directed.

M&L for removing excavated soil to a distance exceeding 250 m but not exc 500m and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed.

M&L for excavating in post holes (or similar holes) each not exceeding 0.5 Cum, getting out, returning filling in and ramming earth or broken rubble mixed with earh around in layers not exceeding 25 cm for soft/loose soil complete all as specied and directed.

M&L for Hardcore of gauge not exc 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to true surface with broken stones complete all as specified and directed.

M&L for plain cement concrete (1:3:6) type C2 using 40 mm graded stone aggregates in foundation filling and mass concrete complete all as specified and directed.

M&L for plain cement concrete (1:2:4) type B1 using 20 mm graded aggregates in roof kerbs or mud stops, rounded or chamfered on edges including formwork complete all as specified and directed.

M&L for brickwork with fly-ash bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for brickwork with fly-ash bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:4 complete all as specified and directed.

M&L brick work using old size sub class 'B' fly-ash bricks straight or curved on plan to any radius in half brick wall, built in cement mortar 1:4 complete all as specified and directed.

M&L Rendering 15mm thick, on fair faces of brick or concrete surfaces of walls in cement mortar 1:4, finished even and smooth without using extra cement complete all as specified and directed.

M&L Rendering 15mm thick, on fair faces of brick or concrete surfaces of walls in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and directed.

M&L Rendering 10mm thick, on fair faces of brick or concrete surfaces of walls in cement mortar 1:4, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar (1:4) on fair faces of concrete or brick surfaces with using water proofing compound @ 3% by weight of cement finished even and smooth without using extra cement for external surfaces of manhole complete all as specified and directed . (Note:- WPC shall be measured & paid separately)

Supply only liquid water proofing compound complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of acrylic distemper over a coat of alkali resistant primer with rollers complete all as specified and directed.

M&L Preparation of new plastered surfaces of wall and applying two coat of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

M&L Preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

M&L for RCC type A1 (1:1½:3) using 20 mm graded aggregates in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc basement slabs, under reamed piles and mass concrete complete all as specified and directed. (NOTE: MS reinforcement shall be measured and paid seperately)

M&L for RCC 1:1½:3, type A1 (using 20mm grade stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and as directed. (NOTE: MS reinforcement shall be measured and paid seperately)

M&L for RCC 1:1½:3, type A1 (nominal mix) (using 20mm graded stone aggregates) as in beams, cantilevers, bressummers, lintels over 1.5 mtr span complete all as specified and directed. (NOTE: MS reinforcement shall be measured and paid seperately)

M&L for mild steel TMT bars 10 mm dia and over cut to length bent to shape, required including cranking, bending , spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for Mild steel TMT bars 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shape required and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for formwork to sides of concrete foundations, footings, bases of column, raft and raft beams, side and soffit (if any) for foundation and plinth beams etc, vertical or to batter for rough finished surfaces complete all as specified and directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressumers, lintels, cantilevers, shelves etc for fair finished surfaces complete all as specified and directed.

M&L for formwork to side of pillars, posts, struts, piers, columns for fair finished surfaces complete all as specified and directed.

M&L for non skid ceramic 8 mm thick coloured tiles (square/ rectangular), area of each tile exc 0.11 Sqm but n.exc 0.38 Sqm, set and jointed in neat cement slurry and pointed in white cement mixed with pigment as in floor, laid over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

-ditto- as per Item No. 24 above but non-skid tiles in skirting fixed over 10 mm thick screed bed in cement mortar 1:3

M&L glazed coloured ceramic tiles in vertical surface 300 X 450 X 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles including 10mm thick screed bed in cement mortar (1:3) complete all as specified and directed.

S&F 15mm bore galvanised steel tubing (medium grade) with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed.

S&F 20mm bore galvanised steel tubing (medium grade) with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed.

S&F 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F PVC connection pipe, 15 mm dia, 450 mm long having PTMT union at each end complete all as specified abd directed. (MAKE : PRAYAG, Cat No. 323 / POLYTUF, Cat No. 4003 / ESS ESS, Cat No: B2CH118 or equivalent model in SHAKTI / JEXON)

Supply and laying 150 mm bore reinforced concrete pipe of Class NP-3, conforming to IS 458-2003, laid and jointed with jute & cement mortar 1:1, complete with collars all specified and as directed.

M&L for PCC 1:3:6, type C-2 (using 40mm graded stone aggregate) as in bedding, packing and haunching to sides of 150mm bore (dia) drain pipes after laying and testing of pipe, complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolts of extruded sections, 150 mm long complete all as specified and directed.

S&F 150mm extruded aluminium handles, fabricated type, anodised complete all specified.

S&F butt hinges, 100 mm long, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-22 complete all as specified and directed.

S&F 300mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all specified.

S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded for fixing wire mesh including one shop coat of priming, complete all as specified and directed. (NOTE : Sheet glass for glazing shall be measured and paid seperately)

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed. (NOTE : Sheet glass for glazing shall be measured and paid seperately)

Supply, hoisting and fixing rotational moulded polythelene water storage tank (cylindrical vertical type with closed top) of capacity 1000 Ltrs, double layered (ISI marked) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed.

S&F 20 mm bore Ball brass valves, high pressure, with HDPE float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. (MAKE : PRAYAG, Cat No. B-152 or equivalent model in JEXON / POLYTUF / SHAKTI)

M&L for PCC 1:2:4 type B2 (using 40 mm graded stone aggregates), 100 mm thick as in sub base of floor complete all as specified and directed.

M&L 18-20mm thick granite slab in window cills, cooking platform etc and like set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match laid over screed bed 20mm thick in cement mortar 1:4 all as specified and as directed.

Supply and fixing 2nd class hard wood plain solid straight chowkhats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

Cutting holes in to brick wall for inserting bold fast & making good dismantled portion in cm (1:3) or PCC (1:2:4) type B1, depth exceeding half brick but not exceeding 1 brick complete all as specified and directed.

M&L for mild steel bands and straps support or stays holdfast and similar articles conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, treating ends of posts, back of chowkhats etc, with tar or coal tar black paint, area tarred exc 0.1 sqm but n. exc 0.5 sqm each complete all as specified and directed.

-ditto- as per Item No. 56 above but treating small articles such as holdfasts, ends of posts, back of chowkhats, etc, area n exc 0.1 sqm each

Supply & fixing factory made 35 mm thick 2nd class hard wood panelled shutters (any Nos of panels) with panels of timber flat on both sides (feather edged) or of veneered particle board medium density wood particle board with commercial face veneers, fitted to chowkhats complete all as specified and directed.

S&F 30mm thick Factory made 2nd class hard wood glazed & skeleton shutters, open rebated and prepared to received glass, gauge etc.(without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part-I section 8, clause 8.20(a) complete all as specified and directed.

S&F Factory made solid PVC door frame (chowkhat) of size 100 mm x 45mm made out of 5mm thick single side prelam PVC sheet, frame reinforced with MS square tube of size 40mm x 20mm of 19 guage throughout the frame, fixed in opening as per specification & drg as per manufacturer instructions complete all as specified and directed.

S&F 28-30mm thick factory made solid PVC moulded door shutter, with 2, 4, or 6 raised panel design with 2mm thick Moulded prelam PVC Sheet on the front face & 2mm plain prelam PVC sheet on back face, complete all as specified against clause 8B 4.1 of SSR Pt-ll and all as shown in product drawing on ser page No. 161 of SSR Pt-ll (2020) complete all as specified and directed.

S&F powder coated (medium thickness of powder coating 50 micron) aluminium frame for door, windows, partitions and ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium doors shutters, aluminium section weighing 0.55 Kg/metre including necessary jointing cleats, glazing clips rubber packing handle 2 Nos in each door, hinges, Mortise lock vertical type size 100 mm 4 levers of brass in each door, anodised aluminium snap beading screws etc with 5.5 mm thick tinted glass ordinary quality as per manufactures instruction complete all as specified and directed. (NOTE: Quoted rate shall be deemed to include for all hardware, lock and sheet glass)

S&F 4.8 mm thick plain sheet glass ordinary quality and glazing with oil putty or wooden beads in square n.exc 0.50 Sqm in each pane complete all as specified and directed.

S&F stainless steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for preparation of new untreated wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and directed. (NOTE: Quoted rates shall be deemed to include for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete)

S&F mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes with riveted, bolted or welded attachment, of grade Fe-290 (Gde E-165) complete all as specified and directed.

S&F 0.50 mm thick TCT (total coated thickness) pre-coloured galvalume sheets with minimum base metal thickness of 0.45 mm, single skin high rib/multi rib profile galvalume sheeting having 1000-1020 mm width and 28-30 mm high crest @ maximum 250-255 mm pitch (centre) with sheets manufactured out of 0.50 mm this TCT (total coated thickness) high tensile galvalume sheets having tensile strength 550 MPA with 18-20 micron top coat over 5 micron primer and 8-10 micron alkyld backer zinc aluminium alloy AZ-150, sheets having a dip metallic zinc (43.5%0 aluminium (55%) & silicon (1.5%) with total mass coating of 150 gms/sqm on both sides, having wide pans with minimum 3 small stiffening ribs for effective water shedding and special male/female ends with full return legs on laps for purlin support and fixed as per existing profile of roof complete all as specified and directed.

All as per Item No. 69 above but 0.50 mm thick coloured plain galvalume sheet as in ridge/valley gutter of roof.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces exc 10 cm width or girth including preparation of surfaces complete all as specified and directed.

S&F RCPC (Reinforced Cement Polymer Concrete) grating slab of size 600 mm x 450 mm x 100 mm thick, of Capacity 3 MT fixed in proper position complete as directed by Engr-in -Charge.

Supply and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed. (NOTE: Cost of sand cushioning is deemed to be included in the quoted rates)

S&F False ceiling with 4mm thick non-asbestos, reinforced, designer board with HPSC (High pressure Steam Curing) of size 595 mm x 595 mm, fixed on and including powder coated aluminium snap grid to support the boards/tiles with aluminium anodised main 'T' section 36mm x 25mm x 1.40mm, cross tee 23.50mm x 23.50mm x 1.40mm thick and aluminium angle 25mm x 25mm x 1.40mm as on edges/sides including hanging arrangements with 1.6mm dia GI wire and anodised adjuster and applying one coat of acrylic distemper over suitable primer on ceiling boards complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) pipes, Type 'B', single socketed in any length with rubber ring joints fixed to walls with clamps for bldg height upto 4 storey complete all as specified and directed.

S&F PVC (SWR) pipes 110 mm OD, Type 'B' single socketed in any length with rubber ring joints, laid in trenches complete.

S&F PVC (SWR) junction single, (Single T) equal or unequal for 110 mm OD SWR pipe complete all as specified and directed.

S&F PVC (SWR) bend, any radius for 110 mm OD SWR pipe complete all as specified and directed.

S&F PVC (SWR) vent cowl for 110 mm OD SWR pipe complete all as specified and directed.

S&F 75 mm dia. PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and directed

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed

S&F vitreous China Squatting pan ‘Orissa’ pattern, size 580 X 440 mm, white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, etc and including making good to floor, complete all as specified and directed. (MAKE : CERA, Cat No: S3010109 / HINDWARE, Cat No. 20042 / PRAYAG, Cat No: 4054 / ASIAN PAINTS, Cat No: WM-32-X)

S&F 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and incl with flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern complete all as specified and directed. (MAKE : PARRYWARE, Model : Slim line Economy / HINDWARE, Model : Sleek Plus / CERA, Model : Corona / PRAYAG, Model: SMART /ASIAN PAINTS, Cat No: PT-27-X)

S&F vitreous china squating plate urinal, white including connections to flush pipe and outgoing pipes complete all as specified and as directed. (Make of Urinal : Parryware, Cat No: C-0573/ CERA, Cat No: S4040101 / HINDWARE, Cat No: 60003)

S&F Vitreous China Wash Hand Basin 550x400mm in size, White (Flat Back or Angle Back Type) with 32mm dia Brass Chromium Plated Waste Fitting, making good disturbed Surfaces in Cement Mortar 1:3 complete all as specified and directed. (MAKE : CERA, Cat No: S2040119 / HINDWARE, Cat No. 10100 / PRAYAG, Cat No: 4645 / ASIAN PAINTS, Cat No: PN-03-X) (NOTE: Waste coupling and Waste pipe shall be measured and paid seperately)

S&F Chromium plated brass Pillar tap, fancy type. with areator, fixed to wash hand basin, complete all as specified and directed. (Make : ESS ESS, Cat No: RO-101 / PRAYAG, Cat No: 6702 / Essco, Cat No: SQT-507KN / SOMANY, Model: ETHER)

S&F Chromium plated brass Angular stop cock, fancy type, concealed type with wall flange fixed to 15 mm bore of Iron pipe complete all as specified and directed. (Make :ESS ESS, Cat No: RO-112 / PRAYAG, Cat No: 6710 / ESSCO, Cat No: SQT-526NKN / SOMANY, Model: ETHER)

S&F Chromium plated brass Bib cock with wall flange, fancy type, fixed to 15 mm bore of Iron pipe complete all as specified and directed. (Make : Ess Ess, Cat No: RB-103 / PRAYAG, Cat No: 6706 / Essco, Cat No: SQT-512KN / / /SOMANY, Model: ETHER)

S&F chromium plated brass over head shower rose with arm, with 3 flow, fixed to 15mm bore of iron pipe complete all as specified and directed. (Make : Essco, Cat No: ALE-536A & EOS-542N / ESS ESS, Cat No: SA-101 & OH-202 / PRAYAG, Cat No: BS-73 / SOMANY, Model: ETHER)

S&F Tubular towel rail, 20mm dia, 600 mm long between flanges including brass chromium plated, complete all as specified and directed. (MAKE : ESS ESS, Cat No : AC-701 / Essco, Cat No : AEC-1111N / PRAYAG, Cat No: BA-40 / SOMANY, Model: ETHER)

M&L for 75mm thick PCC (1:3:6) type 'C-2' (using 40mm graded crushed stone aggregate) as in floor, plinth protection etc, laid in alternate bays, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregates), 25 mm thick as in sub base of floor complete all as specified and directed.

M&L for structural steel work Fe 410-W (Gde-E-250) quality-A in roof trusses (framed), trussed, purlins, crane gantries, rials and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and as directed by the Engineer-in-Charge

M&L for cement concrete (1:2:4) type B1, using 20 mm graded stone aggregate, as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating and necessary formwork complete all as specified and directed.

M & L for Providing precast cement concrete Type B1 1:2:4 (20mm graded aggregate) Set in cement mortar 1:4 in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including necessary forms, moulds, etc complete all as specified and as directed. (NOTE: MS reinforcement shall be measured and paid seperately)

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1, smooth finished and reforming benching as required for 150 mm bore pipe complete all as specified and as directed.

S&F 5.5mm thick plain sheet glass, ordinary quality, frosted on one side, area in squares exc 0.5 sqm in each pane and glazing in aluminium framework/snap beading complete all as specified and directed.

M&L for Rolled mild steel in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes without any attachment Gde Fe 410W complete all as specified and directed.

S&F powder coated (minimum thickness of powder coating 50 micron) aluminium frame (size 92.36mm X 29.70mm X 1.5 mm thick channel size 30.10mm)@1.22 kg/m three track channel for doors, windows, ventilators wit one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. complete all as specified and directed.

M&L Preparation of new plastered surfaces of wall and applying two coat of weather proof exterior emulsion paint over a coat of alkali resistant exterior primer complete all as specified and directed.

M&L for laying and fixing Machine cut kota stone slab flooring 18-20 mm thick over and including 20 mm thick screed base in cement mortar (1:4), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to achieve high gloss finish complete all as specified and directed.

S&F in position, at or near ground level, factory made precast cement concrete kerb stone blocks, in M-25 grade cement concrete, fixed to the required line, level and curvature, jointed in cement mortar 1:3, including making joints with or without grooves (thickness of joints, except at sharp curves shall not be more than 5 mm) including making drainage opening wherever required complete all as specified and directed.

M&L for grinding/polishing and cutting to existing stone floor of any description (such as kota stone, marble stone, terrazo surfaces etc) cleaning with water and applying zinc oxide powder to achieve high gloss finish complete all as specified and as directed. (NOTE: This item shall only be executed for old existing stone surfaces)

SCHEDULE 'A' PART-II (ELECTRIFICATION WORKS) M&L for concealed type point wiring with 1.50 Sq. mm (nominal area) FRLS-H PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and including PVC conduit complete with all fittings and accessories, fixed to walls/ceiling, including mild steel terminal boxes 1.25 mm thick conforming to IS-5133 (Part-I) with 3.0 mm thick plastic laminated sheet top cover (ISI Marked) for mounting switches/ regulator /bell push etc and including 1.50 Sq. mm (nominal area) FRLS-H PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly, for one light point /bell point/ ceiling fan/exhaust fan point controlled by one way switch complete all as specified and directed. (NOTES: - (i) Where tube light fitting is to be fitted/suspended, CI Circular boxes shall be provided with the PVC Pipes in the ceiling & the unit rate shall be deemed to be included for the same. (ii) Cost of cutting chases for concealed wiring shall be deemed to be inclusive in the quoted rates. No claim in this regard shall be entertained at a later stage)

All as per item No. 105 above but for one 5 amps switch socket outlet on same board controlled by another switch, complete all as specified and directed (concealed type point wiring with terminal box).

All as per item No. 105 above but for one 5 amps switch socket combination on independent board, complete all as specified and directed (concealed type point wiring with terminal box).

All as per item No. 105 above but using 2.5 sqmm single core multi stranded copper conductor FRLS-H PVC insulated and unsheathed, cable for 3/6 pin 15 Amp socket outlet controlled by one switch on independent board with and incl 2.5 sqmm green FRLS-H PVC insulated and unsheathed, copper conductor as continuous earth wire with lugs complete all as specified and directed (concealed type point wiring with terminal box).

S&F switch piano flush button AC 230 V Single pole 5/6 Amp one way complete all as specified and directed.

S&F socket outlet, non-shuttered, 2-in-1, 3 pin, 6 Amp AC 230 Volts flush type complete all as specified and directed.

S&F switch socket combination, 5 pin, 6 Amp AC 230 Volts flush type complete all as specified and directed.

S&F switch socket combination 2 in 1, 3 pin, 6 and 16 Amps flush type universal complete with all necessary electrical connection all as specified and directed.

S&F lamp holder, PVC/Polycarbonate body with back plate suitable for batten/pendant fittings or to be mounted on walls complete all as specified and directed.

S&F ceiling rose surface, polycarbonate/bakelite, three terminals complete all as specified and directed.

S&F surface mounted LED luminaire, 1 X 20 Watt in aluminium housing, with lumen efficacy of 110 lumen/watt, operating voltage 180-270 V, with acrylic/polycarbonate difuser & integrated constant current electronic driver complete with all other accessories internally prewired and incl connecting up with three core flexible copper wire of suitable size complete all as specified and directed.

S&F exhaust fan, 300 mm sweep, made of sturdy engineering plastic with louver shutter, voltage 230V, 50Hz and connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 1.0 Sq mm, 3 core, 1100 Volts grade, from ceiling rose to fan complete all as specified and directed. (Make: BAJAJ, Model : Maxima DxI 300 mm White Dom Exhaust Fan / HAVELLS, Model: Maxima DS or equivalent model in CROMPTON / USHA)

M&L for sub main wiring with 2 runs of FRLS-H PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm alongwith one run of FRLS-H PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm as earth continuity conductor drawn through and including PVC conduit of suitable size complete all as specified and directed. (NOTE : Three runs of single core 4.0 sqmm cable & one run of PVC conduit shall be measured as one unit)

S&F SPN DB, IP 43 protection, double door, 240 volts, 8 way, with 100 Amps copper Bus Bar complete all as specified and directed.

S&F MCB, 'C' series, SPN, 32 Amps, breaking capacity 10KA complete all as specified and directed.

S&F MCB, 'C' series, single pole, 6 to 32 Amps, breaking capacity 10KA complete all as specified and directed.

Supply, installation, testing and commissioning of heater water storage type electric geyser (vertical cylindrical type) 25 ltrs capacity with BEE 5 star rating (min) and ABS body, glass lined/titanium enamel coated inner tank incl fixing arrangement with providing incl suitable capacity flexible cable 3 core with 3 pin plug of 16 amp complete all as specified and directed. (Make: RACOLD, Model - CDR DLX / AO SMITH, Model- HSE-VAS / Havells, Model: Monza Dx / BAJAJ, Model: CALDIA)

SCHEDULE 'A' PART-III (EXTERNAL WATER SUPPLY) S&F galvanised tube, medium grade, 25mm dia with necessary fittings complete laid in trenches complete all as specified and as directed.

S&F gun metal gate or globe valve, with iron wheel head, screwed both ends for iron pipe and fixed for 25 mm bore pipe complete all as specified and directed.

Drilling and tapping cast iron/GI water mains (in position) for branch connections for 40 mm internal dia complete all as specified and directed.

KWALITY CONSTRUCTION

MODERN AGENCY

SK CONSTRUCTION SYNDICATE & ENGG CO

M/S SRINIVASA CONSTRUCTION

M A ENTERPRISES

UNITED ENGINEERS