ADDN / ALTERATION INCLUDING REPAIR TO JCOS/OR MD ACCN AT MATHURA CANTT (PH II OF II PHASES) UNDER GE (WEST) MATHURA

Amount

Taking down Chowkhats or frames with shutter without taking off shutters from the frames not exc. 1.5 sq. m each complete all as specified and directed.

Taking down Chowkhats or frames with shutter without taking off shutters from the frames exc 1.5 sq. m but n exc 4 sq. m each complete all as specified and directed.

S&F 125X60 mm pressed steel frames made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. with one shop coat of red oxide primer complete all as specified and directed.

S&F 105X60 mm pressed steel frames made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. with one shop coat of red oxide primer complete all as specified and directed.

S&F 35mm thick factory made IInd class hard wood panelled door shutters (two numbers of panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail & stile as per IS :1003 (Part-I) kilnseasoned and chemically pressure treated complete all as specified and directed.

S&F Factory made IInd class Hard wood 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet PVC sheet reinforced with M.S. square tube,supplying & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter with particle board core, 30mm thick (stiles), with 2, 4, or 6 raised panel design with 5mm thick Moulded PVC Sheet on the front face & 5mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F 200mm long Aluminum anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F for 150mm long Extruded aluminium alloy handles, cast type, anodised complete all as specified and directed.

M&L cement concrete type C-1 (1:3:6) 20mm graded stone aggregate as in blocks for fixing hold fasts and filling of chowkhats or any other similar purpose complete all as specified and directed.

S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed.

Supply & Fix 200 mm long Stainless Steel barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 300mm stainless steel sliding door bolt, bolt type with bright bolt not less than 12mm dia with and inlcuding a minimum of 6 bolts and nuts, four on bolt plate and tow on staple plate and fixed complete all as specified and directed.

S&F for 150mm long Stainless steel handles complete all as specified and directed.

S&F stainless steel Hat pegs set of 6 solid body anodised complete all as specified and directed.

S&F Hasp and staple 100mm long, aluminium stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F floor door stopper of aluminum alloy body and tongue, with hard drawn steel spring fixed in floor 140 mm long complete all as specified and directed.

S&F tubular towel rail, aluminium anodised 20mm dia D type, 60cm long between flanges complete all as specified and directed.

S&F for 100mm long Extruded aluminium alloy handles, cast type, anodised complete all as specified and directed.

S&F for Harrison rails, 25mm dia mild steel chromium plated with fixing brackets, stops, rollers with decorative caps etc complete all as specified and directed.

S&F for 300mm, Mild Steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

S&F coloured Non Skid ceramic tiles 9 mm thick, (Square / rectangular) area of each tile exceeding 0.16 Sqm but n.exc 0.38 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade over and including 15mm thick screed bed in CM (1:4) complete all as specified and directed.

S&F coloured Non Skid ceramic tiles 9 mm thick (Square / rectangular) polished area of each tile exceeding 0.16 Sqm but n.exc 0.38 Sqm in skirting / dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade over and including 10mm thick screed bed in CM (1:3) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

S&F coloured Non Skid ceramic joint free tiles 7 to 8 mm thick, (Square / rectangular) area of each tile exceeding 0.11 Sqm but n.exc 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade over and including 15mm thick screed bed in CM (1:4) complete all as specified and directed.

M&L for coloured glazed ceramic tiles of size 600 X 300 x 7mm thick as in vertical surface set and jointed in neat cement slurry and pointed in white or colour cement to match the shade over and including 10mm thick rendering in cement mortar (1:3) complete all as specified and directed.

M&L for 18-20mm thick granite (of any type) work table rubbed and polished for shelves (veneering to wall including 12mm thick plaster in CM (1:3) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L Machine cut kota stone slab flooring 18-20mm thick of size 550 x 550mm laid in floor and jointed with pigment to match the shade of the slab including rubbing and polishing including screed bed 20mm thick in CM 1:3 for laying finishes complete all as specified and directed.

M&L Kota stone slab 18-20mm thick (One piece) in riser of steps, skirting, dada and pillar laid over 15mm thick backing coat in CM 1:4 cement screed base laid cement screed and jointed complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floor), beams, staircases, loading chhajjas and similar suspended work complete all as specified and directed.

M&L RCC M-25 (design mix) using 20mm graded stone aggregate as in lintel chhajja supported on walls and other similar work complete all as specified and directed.

M&L for mild steel TMT bars as in reinforcement 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel (wire) annealed not less than 0.9mm dia complete all as specified and directed.

M&L for form work to chajjas, chullah hoods for rough finished surfaces on concrete and similar items including edges flat complete all as specified and directed.

M&L for Formwork to edges of concrete flats, treads breaks in floors, window cill concrete railling, opening in concrete walls floor and roof n.exc 5 cm but n.exc 10cm wide and sides RCC / PCC band in walls horizontal and sloping and similar work with fair finished surface exc 5cm but not exc 10cm wide complete all as specified and directed.

Demolition of brick work or stone boulder masonary built in cement mortar including all quoins arches pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

M&L for Brickwork with fly ash old size bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints,hacking for key,scrubbing down with water, etc. complete all as specified and directed.

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces finished fair and even in CM 1:4 mixed with liquid water proofing compound as per manufacturers instructions complete all as specified and directed. (liquid WPC shall be measured and paid separately)

M&L for 10mm thick rendering in cement mortar (1:6) on fair face of brick walls/ concrete surfaces and finished even and smooth without using extra cement complete all as specified and directed.

M&L for Rendering 5 mm thick including dubbing coat in cement mortar 1:3 on ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) in plinth protection finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L for cement concrete type B-1, 1:2:4 using 20 mm graded stone aggregate as in benching / coping and the like incl weathering slightly round or chamfered angles and throating complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-2 (by using 40mm graded stone aggregate) as in floor and finishing even and fair complete all as specified and directed.

M&L for chequered cement concrete tiles 30cm x 30cm x 25mm thick, machine pressed, with white cement and pigment rubber moulded glossy finish set jointed and pointed in neat cement slurry in floors and including 20mm thick screed bedding in cement mortar (1:4) complete all as specified and as directed.

M&L for Machine pressed precast concrete interlocking paver block with grey cement and no pigments any shape and size confirming to IS 15658-2006 of 60mm thickness, M-40 Grade laid over and including 25 mm thick sand filling complete all as specified and directed.

Taking down existing treatment from sunken portion of WC /Bath /Kitchen / Passage including floor tiles, plaster, lime/cement concrete, WC trap to complete empty of existing sunk complete all as specified and directed. Note : 1.Taking down of plumbing & sanitary fitting & fixture shall be measured under relevant items. 2. All debris obtained from site will be thrown away outside defence land by contractor at his own expense.

M&L for Cutting holes into or through brick walls built in cement mortor superficial area n exc 150 sq cm and making good in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed. Note : The cutting of chases will be done using wall chaser / wall groove cutting machine only.

S&F PVC (SWR) pipes type ‘A’ 110 mm dia single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed

S&F PVC (SWR) pipes type ‘A’ 75 mm dia single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed. Note : The cutting of chases will be done using wall chaser / wall groove cutting machine only.

M&L for Providing, cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate in coping, coving, roof padding, padding in sunken slab as directing mixed with liquid water proofing compound as per manfacturer's instraction complete all as specified and directed. Note :- liquid WPC shall be measured and paid separately as supply only under respective item of this Sch.

M&L for cement concrete (1:5:10) type E-1 using 40mm graded stone aggregate as in filling of sunken portion complete all as specified and directed.

M&L for rendering 10 mm on fair faces of brick wall or concrete surface in cement mortar 1:4 finished even & fair without using extra cement including mixed with liquid water proofing compound @ 200ml per bag of cement or as per manufacturer instruction complete all as specified and directed. Note :- Liquid Water Proofing compound will be measured and paid separately as supply only under respective item of this Sch .

Supply only liquid water proofing compound complete all as specified and directed.

Dismantling brick tiles or terracing tiles, single layer on roofs complete all as specified and directed.

Demolition of mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) including removal of demolished material to a distance exc 250m & n.exc 500m and depositing when directed as a level n.exc 1.5m above starting point complete all as specified and directed.

M&L for water proofing treatment with APP modified bituminous membrane 3mm thick consisting complete all as specified and directed. following for RCC roof:- (i) Cleaning plastered roof surfaces and applying a coat of Oxidized bitumen based solvented primer @0.3 Kg/Sqm of approved make on top of dry surface of RCC roof complete all as specified and directed. (ii) M&L for APP modified polymeric waterproofing membrane 3mm thick with non woven polyester core of approved make applied by heating one surface of membrane with LPG torch with lap of 100mm and the overlap shall be seated by flame complete all as per manufacture instructions and as directed by EIC.

M&L for cement concrete tiles 25cm x 25cm x 20mm thick, machine pressed, set jointed and pointed in neat cement slurry in floors, and cut and polished built with grey cement and no pigment over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

Taking up or down 15 mm bore of dia steel tubing and connections, complete all as specified and directed.

Taking up or down 20 mm bore of dia steel tubing and connections, complete all as specified and directed.

M&L 15 mm nominal bore Mild steel galvanized water tubing , medium grade , with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

M&L 20 mm nominal bore Mild steel galvanized water tubing , medium grade , with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

Dismantling cast iron work of any description complete all as specified and directed.

Dismantling old PVC pipe of any description 75 / 110 mm dia complete all as specified and directed.

S&F PVC (SWR) pipes type 'A' 110 MM dia single socketed, in any length with rubber ring joints laid in trenches or in floors including dismantling existing pipe complete all as specified and directed.

S&F PVC (SWR) pipes type 'A' 75 MM dia single socketed, in any length with rubber ring joints laid in trenches or in floors including dismantling existing pipe complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends any radius with access door complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends any radius with access door complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction, single T equal or unequal with oval access door complete all as specified and directed.

S&F 75mm bore PVC (SWR) junction, single T equal or unequal with oval access door complete all as specified and directed.

S&F 110mm PVC (SWR) vent cowl complete all as specified and directed.

S&F 75mm PVC (SWR) vent cowl complete all as specified and directed.

S&F in repair 15mm bore chromium plated cast copper alloy bib taps with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair chromium plated stop cock / angle type cast copper alloy screwed down high pressure with crutch or butterfly handles screwed both ends for iron pipe 15mm bore complete all as specified and directed.

S&F in repair chromium plated stop cock cast copper alloy screwed down high pressure with crutch or butterfly handles screwed both ends for iron pipe with long shank and cup (concealed type) 15mm bore complete all as specified and directed.

S&F vitreous china squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including setting the trap and pan in concrete and including 10 ltr capacity PVC valveless syphonic action type low level flushing cistern and 32mm dia PVC flush pipe complete including jointing to socket of flushing rim, complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets angle iron 50x50x6mm with suitable length and connecting union to pipe, waste pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repair vitreous china wash basin white flat back size 550 x 400mm size, incl cutting for and pinning in ends of brackets or erecting stand but including fixing of supply and waste pipe & waste fittings complete fixed complete all as specified and directed.

S&F in repair brass chromium plated shower rose with swivel joint 125mm size and including 195mm long brass CP bend of 45 degree and flange complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450 mm including fixing complete all as specified and directed.

S&F chromium plated fancy type pillar taps cast copper alloy with capstan head screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and fly nuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed.

Dismantling water tanks of any type description of capacity exc 500 liters but n.exc 1000 liters complete all as specified and directed.

M&L Rotational moulded polyethylene water tanks tripple layered WHITE COLOUR (cylindrical vertical with closed top) hoisted and fixed in position for 750 ltr. Storage capacity complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coat of white wash on ceiling complete all as specified and directed.

M&L for bands, straps, supports or stays for rainwater ventilating pipes, including bolts and similar small articles conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F 20mm bore ball brass valve high pressure with polythene float and fly nut, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F 32mm bore waste fittings, brass, chromium plated for basins with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F 40mm bore waste fittings, brass, chromium plated for sinks with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F 20mm GI nipple suitable for HDPE water tank omplete all as specified and directed.

S&F Low density poly ethylene (LDPE) waste pipe 32mm dia of length 0.8m to 1.00m of pressure rating 6 kgf/Sqcm and fixed to WHB sink complete all as specified and directed.

M&L Cutting chases, pinning in making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, for concealed water tubing etc and making good, cutting n.exc 10cm girth in brick wall complete all as specified and directed. Note : The cutting of chases will be done using wall chaser / wall groove cutting machine only.

M&L for preparation of new wooden surfaces of any description not otherwise described exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified & directed.

M&L for preparation of new steel surface of any description not otherwise described exc 10cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper over and including a coat of primer and a coat of wall care putty to smooth finish complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying three coats of white wash on ceiling surfaces complete all as specified and directed.

M&L for complete removal of existing treatment on wall and applying two coat of oil bound distemper complete all as specified and directed.

M&L for cement concrete (1:3:6) types C-2 (40mm graded stone aggregates) as in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds complete all as specified and directed.

M&L for Elastomeric Pedeilite Raincoat Paint over the exposed surface of cupboard wall etc. complete all as specified and directed

S&F hard drawn steel wire fabric weight n exc 4 Kg/sqm cut to length, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9 mm in dia complete all as specified and directed.

Supply & fix 75mm long Butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed.

M&L for 40mm thick (measured solid) precast cement concrete louvers and jallies type B-0 mix 1:2:4 (using 12.5mm graded stone aggregate) including all mouldings but excluding frame set in CM 1:4 complete all as specified and directed.

Applying one coat of epoxy resin (FAIR BOND EP) on old concrete/brick surfaces @ 0.30Kg/sqm including of surfaces as per manufacturer's instructions and applying 25mm thick (average thickness) of cement and sand (fine grit) in ratio 1:4 mixed with chloride free spray concrete plasticiser (spray crete) as per manufacturer's instruction with grunting machine of pressure capacity not lass than 5 kg per Sqm and finished the surface even and smooth in CM 1:4 complete all as specified for buildings not more than triple storeyed. Make : Fairmate chemicals or equivalent make of Pidilite /Fosroc.

Dismantling loose/disintegrated portion of RCC Chajjas, bands, shelves, beams, column or slab and similar work including support if required and stitching of cracks with MS U clamps of 8mm dia @ 150mm c/c with inserting concrete block stretcher with cement mortar 1:3 mixed with adhesive chemical (polymer based) and reinforced with PVC chicken mash including form work where ever required and finished with 10mm thick plastering in CM 1:4 finished even & smooth without using extra cement including preparation of surfaces to receive finishes complete all as specified and directed.

M&L for 150mm bore Reinforced concrete pipes class NP2 laid and jointed with collars in trenches complete all as specified and directed.

M&L PCC (1:3:6) type C-2 using 40 mm graded stone aggregate as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150mm dia pipe complete all as specified and directed.

Cutting opening, through brick walls built in cement mortar for door, window and other openings or enlarging existing openings, converting window into door openings, etc or cutting out defective brick work for under pinning, including providing, fixing and removing shoring cleaning and stacking bricks, removing surplus serviceable bricks, hard core etc and rubbish off premisses complete all as specified and directed.

M&L for precast reinforced cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in landing, cover slab (for manholes, soakage well etc) and similar articles with plain faces set in CM 1:4 complete all as specified and directed.

S&F 18mm thick Alston Hybrid water proofing board in cupboard shutter/kitchen cabinet with decorative on one side & other side balancing white fixed with necessary stainless steel drilling screws/Anchoring bolt with and including 100 mm modular handles, design and colour as approved by GE complete all as specified and directed.

S&F continuous piano hinges mild steel bright finish or electro galvanised of 30mm width of flaps complete all as specified and directed.

S&F 20mmX50mm size Magnatic catcher for cupboards including fixing to frame and connected plate to shutter complete all as specified and directed.

S&F stainless steel kitchen plate rack overall size 900 x 900 x 200mm made out of 0.8 mm thick stainless steel sheet etc complete all as specified and directed.

S&F 18mm thick Alston wood polymer composive Board (WPC) in cupboard shutter with decorative on both side design fixed by drilling screws complete all as specified and directed.

M&L 4mm thick plain sheet glass, ordinary quality n.exc 0.5 Sqm in each pane complete all as specified and directed.

S&F powder coated aluminium frame (minimum thikness of powder coating 50 micron) for doors, windows, ventilators (sliding / fixed or casement) with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Anodised powder coated aluminium window and ventilator shutters, fixed type with sash bar and louvered, aluminium section weighing 0.55 Kg/M including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed.

S&F powder coated (minimum thickness of powder coating 50 micron) aluminium window and ventilator shutters, side hung type without sash bar, aluminium section weighing 0.55 Kg/M including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc and anodised aluminium fittings such as peg stay 150mm long (01 No), hinges type B-21 100mm long (02 Nos), aluminium handle 100mm (01 No) complete all as specified and directed.

Excavation in trenches in soft / loose soil not exceeding 1.5m wide and not exceeding 1.5m in depth for laying of cable etc and for foundation of poles, stays etc, not exc 10 sqm on plan and n exc 1.5m in depth and getting out complete all as specified and directed.

M&L preparation of new plastered surfaces and applying two coats of exterior weather coat and primer on walls complete all as specified and directed

M&L for complete removal and preparation of old painted surfaces of wall and applying two coat of exterior emulsion APEX over a coat of primer complete all as specified and directed.

Supplying and applying, Smart Care Damp Block 2K, two component elastomeric acrylic polymer modified cementations waterproofing coating, having 80 % elongation as per ASTM D412, resisting 5 bars hydrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per DIN 1048, crack bridging upto 1.2mm as per ASTM 4548.5. The mixing ratio of the coating shall be 2 parts of powder & 1 part of liquid without any water addition in the mixing, etc. Complete as per manufacturers specifications. Sprinkle sand at 10-15 gram per sqft for better grip with plaster complete all as specified and directed

Excavation in trenches in hard/dense soil not exceeding 1.5 m wide and not exceeding 1.5 m in depth for laying of cable etc. and for foundation of poles, stays etc. n exc 10 sqm on plan and n exc 1.5 in depth and getting out complete all as specified and directed.

Returning filling in including spreading, leveling, watering and well ramming in layers n.exc 25cm in hard/dense soil complete all as specified and directed.

M&L for removing excavated soil / material to a distance not.exc. 50m and depositing where directed at a level not exc. 1.5m above starting point complete all as specified and directed.

M&L approvd locally available river sand in treches for sand cushion for laying of cables to the full width of excavated trench, gently punned down etc all as specified and as directed.

M&L bricks slightly over burnt (kiln burnt), old size bricks, best quality locally available, laid flat dry, laid in trenches for cable protection all as specified and as directed.

Supply, laying, and testing LT cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty)1100 Volts grade with stranded aluminium conductor of cross sectional area of size 25 Sqmm 4 core complete all as specified and directed.

Supply and laying in replacement of galvanised iron pipe 50mm dia light grade including all fittings for protection of UG cable complete all as specified and directed.

M&L for drilling hole trenchless technology under road for laying of U/G cable through pipe of suitable size at site. complete all as specified and directed.

Taking down aluminum/copper point wiring (light ,fan, socket any type, power, bell etc.) complete including fixtures & fittings (such as ceiling rose, socket, Pendent, regulator, light fitting etc) and removing the material from site and making good the disturbed surfaces of walls ceiling etc complete all as directed.

M&L for point wiring alongwith earth continuity conductor with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black, Earth - Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20mm dia ISI marked ivory colour with all conduit fittings / fixing accessories including cast iron/ Pressed steel terminal boxes 60mm deep for mounting switches, sockets, fan regulators etc duly painted on inside & out side two coats of black bituminous paint over a coat of red oxide primer with 3mm thick bakelite sheet top cover including cutting, chasing on wall and other surfaces and making good disturbed surface complete for the following :-

One light point controlled by one switch.

One ceiling / exhaust fan point controlled by one switch.

One light point controlled by two way switch.

One 3 pin socket outlet 5 amp point controlled by one switch on the same board with other switches.

One 3 pin socket outlet 5 amp point controlled by one switch on independent board.

One bell point controlled by one bell push.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multi stranded copper conductor cable 2.5 sqmm (Phase-Red, Neutral-Black) and earth continuity conductor 2.5 Sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20mm dia ISI marked ivory colour with all conduit fittings/fixing accessories and unwelded sunken galvanized pressed steel terminal boxes of thickness not less than 1.2mm covered with 3 mm thick phenolic laminated white sheet cover for mounting switches as required for one light point controlled by one switch on 16 amp independent board complete all as specified and directed

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 4 sqmm drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories including galvanised sunken pressed steel terminal boxes of thickness 1.12mm covered with 3mm thick phenolic laminated white sheet cover with earth continuty conductor with FRLS PVC insulated multistranded copper conductor cable 4 Sqmm complete for one 16 Amp socket outlet controlled by one switch on independent board, including making the good disturbed surface complete all as specified and directed.

Supply and Fixing switch piano, flush type single pole one way 6 Amp complete all as specified and directed.

Supply and Fixing flush type single pole two way 6 Amp switch complete all as specified and directed.

Supply and Fixing bell push flush type 6 Amp 240 Volts complete all as specified and directed.

Supply and Fixing bell ding dong type, AC, 240 Volts complete all as specified and directed.

Supply and Fixing socket outlet 2 in 1, 3 pin 6 Amp flush type complete all as specified and directed.

Supply and Fixing switch piano, flush type single pole one way 16 Amp complete all as specified and directed.

Supply and Fixing socket outlet 2 in 1, 3 pin 6 and 16 Amp flush type complete all as specified and directed.

S&F hum free electronic ceiling fan step regulator 120 to 180 volt, 100 watt capacity (socket type) including necessary connection complete all as specified and directed.

S&F angle holder insulated polycarbonate body complete all as specified and directed.

S&F ceiling rose of 63 x 30mm PVC/polycarbonate three terminal surface bakelite complete all as specified and directed.

S&F LED (1.2 M) smartbrite extra batten made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumen/20 watt at a minimum system efficacy of 2000 lumen per 20 watt and total power consumption not more than 20 watt including driver of capacity 10 KA. it has a rated system life time of 25000 burning hours at L70 and should have a colour temperature of 6500 K, CRI>80, THD<10% AND PF>0.95 complete all as specified and directed.

S&F in repair LED bulb base B-22 of capacity 10 Watts not less than 700 lumens output at 6500K colour temp complete all as specified and directed.

S&F of LED (0.6 M/ 2 ft) smartbrite extra batten made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 1150 lumen/10 watt at a minimum system efficacy of 1150 lumen per 10 watt and total power consumption not more than 10 watt including driver of 5 KA capacity. it has a rated system life time of 25000 burning hours at L70 and should have a colour temperature of 6500 K, CRI>80, THD<10% AND PF>0.95 complete all as specified and directed.

S&F Security Light of 30 watts of new generation energy saving & environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having IP65 protection and impact resistance of IK07 with 10KV Built -in-Surge Protection Division including suitable pipe, clamps, nut and bolts for mounting the light all as specified and directed

S&F environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagon bulk head back-lit LED luminaire comprising of high brightness LEDs lamp of 10 Watt complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of complete all as specified and directed.

M&L for concealed sub main wiring with PVC insulated FRLS-H multistranded copper conductor cable of size 2x6.0 Sqmm drawing into and including rigid non metallic PVC conduit, medium grade not less than 25mm dia ISI marked ivory colour with all conduit fittings and fixing accessories and 6.0 Sqmm FRLS-H multistranded copper conductor cable as continuous earth wire including cutting chasing and making existing colour on the wall complete all as specified and directed. (Note :- two runs of 6 Sqmm copper wire and one run of 6 sqmm copper earth wire alongwith PVC conduit shall be measured as one unit)

Taking down carefully sub main wiring with PVC casing capping/PVC surface conduit and making good disturbed surface to match the existing complete all as specified and directed.

Taking down MCB distribution boards with incoming and outgoing controls any make, any capacity after disconnecting complete all as specified and directed.

Taking down old unserviceable indoor type panel of any capacity complete all as specified and directed.

Supply, installation, testing and commissioning of LT indoor building panel board fabricated out of 2.0 mm thick stainless steel (SS 316) with copper bus bar 4 pole equal of capacity in colour code R,Y&B, 200 Amps 415 Volts indoor type wall mounted of size not less than 500mmx450mmx200mm, installed on porcelain insulators with bus bar chamber. The panel shall be dust and vermin proof, protection class IP 42 class, front opening & compartmental type with approach for cable entry and for easy maintenance duly internally wired with FRLS, PVC insulated stranded copper conductor cable of 1.0 Sqmm including LED indicator for R,Y & B and comprising of the following:- Incoming :- One number MCCB 63 Amps 4 pole 16 KA 415 Volts, 70-100%, 50 Hz Make :- Legrand cat No. 4200 16 or equivalent in Hager/Schneider. Outgoing:- MCB DP 32 Amps "C' series 10 KA AC 240 volts-04 Nos

S&F factory made, sheet steel distribution boards double door, protection class IP-42 suitable for mounting MCB, DBs conforming to IS-13032, IS-8623, BS-5484 with min 100 Amps rating copper bus bar, SP& N 8 Ways complete all as specified and directed

S & F MCBs of 'C' series double pole 6 to 32 amps having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete Legrand Cat Part No 408628-36 or equivalent in make as specified in Appendix 'B'. complete all as specified and directed.

S & F MCBs of 'C' series single pole 6 to 32 amps having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete Legrand Cat Part No 408587-95 or equivalent in make as specified in Appendix 'B'. complete all as specified and directed.

M&L for making of hole in brick wall including removal of dismantled materials, making good disturbed surface, plastering, making holes fixing bolts suitable for 300/200mm dia fixing 10" exhaust fan frame complete all as specified and directed.

M&L for making of hole in brick wall including removal of dismantled materials, making good disturbed surface, plastering, making holes fixing bolts suitable for 300/200mm dia fixing 12" exhaust fan frame complete all as specified and directed.

S&F 20 Amp, single pole and neutral socket outlet with 2 pole and earthy, metal enclosed plug top in power coated CRCA steel sheet enclosure recess mounted with chained metal cover for socket outlet with and including one number single pole 'B' series MCB 20 amp as required complete all as specified and directed.

S&F and commissioning (maximum energy efficient type) water heater storage type, with 2 KW heating element, electric complete of capacity 25 liters, vertical, metallic body including grouting of studs in wall in CM 1:3 nuts, washers and provision of two numbers PVC connection 600mm long with brass nuts and two number brass chromium plated angular valve suitable for 15mm bore pipe for water supply connection complete all as specified and directed. Make : Havells, Monza EC or equivalent makes as specified in Appendix 'B'.

M&L for cutting existing tubing and taking up for tapping/termination of pipe line, screwing including existing steel tubing of size 15mm dia complete all as specified and directed.

Taking down of ceiling fan 1200/1400 mm of any make & capacity from any height and removing its blades and refixing the same including material and labour for rewinding, with super enameled copper conductor of suitable size, meet to original specification & speed including varnishing, heating etc including taking out old copper wire and painting of ceiling fans (motor and blades etc) of existing colour or approved by Engr-in-Charge with super enameled paint one coat complete all as specified and directed.

Taking down of ceiling fan 1200/1400 mm of any make & capacity from any height overhauling of fan motor of any size and removing unserviceable grease, bearings, bushes, split pin, nuts and bolts and cleaning with petrol/kerosene applying new grease and reassembling complete including replacement of worn out spares with new like split pin, nut & bolts and painting of ceiling fans (motor and blades etc) as per existing colour or approved by Engr-in-Charge with super enameled paint one coat all as specified and directed.

Supply and fixing exhaust fans 250 mm sweep, ventilator, three blade double ball bearing, metallic body, 1400 RPM, minimum air delivery discharge 1710 CMH suitable for SP, 230/250V, 50 Hz AC supply with protective bird guard with louver shutters including grouting of frame in wall and connecting with and including 3 run 1.5 Sq mm single core, PVC insulated but unsheathered FRLSH multistranded copper conductors cable from ceiling rose to exhaust fan complete all as specified and directed. Make : Havells or equivalent makes as specified in Appendix 'B'.

Supply and fixing exhaust fans 300 mm sweep metallic body, heavy duty, four blade, double ball bearing, 1400 RPM, minimum air delivery discharge 1710 CMH suitable for SP, 230/250V, 50 Hz AC supply with protective bird guard with louver shutters including grouting of frame in wall and connecting with and including 3 run 1.5 Sq mm single core, PVC insulated but unsheathered FRLSH multistranded copper conductors cable from ceiling rose to exhaust fan complete all as specified and directed.

M&L in replacement of Earthing complete with galvanized steel earth plate electrode 60cmx60cmx 6.3mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meter below normal ground level, connected to galvanised earth strip 25x4 by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES SSR Part I connected to main DB or main control board all as specified and testing on completion including provision of earth wire protected by galvanised iron 40 mm bore light grade pipe with all fittings from the earth electrode fixed along pole with and including 25 x 6 mm flat iron clamp, bolts, nuts and washers and watering pipe shall be 20 mm bore GI medium grade from Top of the earth electrode to bottom of the earth pit and earth electrode shall be surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides including all excavation and earth work in any type of soil and removal of soil upto 50 metre, PCC pit with pre-cast RCC cover with handle with 10mm dia, charcoal/salt, funnel, CI frame etc complete all as specified and directed

Taking down of existing exhaust fan of any make & capacity from any height overhauling of Exhaust fan motor of any size and removing unserviceable grease, bearings, bushes, split pin, nuts and bolts and cleaning with petrol/kerosene applying new grease and reassembling complete including replacement of worn out spares with new like split pin, nut & bolts and painting of exhaust fans (motor and blades etc) as per existing colour or approved by Engr-in-Charge with super enameled paint one coat & refixng the same location all as specified and directed.

Taking down of existing geyser of any make & capacity from any height & replacing the burn out heating element & replacing the wear part as nut bolt etc and refixing the same location complete all as specified and directed

M/S YATENDRA SINGH

shyam construction

M/s Singh Engineering Corporation