81775 SPECIAL REPAIRS TO KILO SQN AT NDA UNDER GE PROJECT NDA KHADAKWASLA

Amount

Material and labour for complete removal of existing treatment by mechanical means on plastered surfaces of walls and applying wall care putty of 1.5 mm thick in two layers over plastered surface to prepare the surface even and smooth, and applying two coats of acrylic emulsion distemper over and including a coat of primer all as specified and as directed.

Material and labour for complete removal of existing treatment by mechanical means on plastered surfaces of ceiling and applying wall care putty of 1.5 mm thick in two layers over plastered surface to prepare the surface even and smooth, and applying two coats of acrylic emulsion distemper over and including a coat of primer all as specified and as directed.

Material and labour for preparation of newly plastered surfaces of walls and applying wall care putty of 1.5 mm thick in two layers over plastered surface to prepare the surface even and smooth, and applying two coats of acrylic emulsion distemper over and including a coat of primer all as specified and as directed.

Material and labour for preparation of newly plastered surfaces of ceiling and applying wall care putty of 1.5 mm thick in two layers over plastered surface to prepare the surface even and smooth, and applying two coats of acrylic emulsion distemper over and including a coat of primer all as specified and as directed.

Material and labour for complete removal of existing treatment by mechanical means on plastered surfaces of walls/ceilings and and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over plastered surfaces all as specified and as directed.

Material and labour for complete Removing old paint by hot air Gun machine, any number of coats and prepare the surface by scrapping with mechanical means till the surface achieve orignal wood finish, including filling cracks, holes, damaged surface with filler material/ lipping patti on door shutters and frames where required on old wooden surfaces any width or girth and applying two coats of synthetic enamel paint over a pink primer coat all as specified and as directed. (Note :- The cost of filling cracks, holes, damaged surface with filler material/ lipping patti to be included in quoted rate and nothing shall be admissible on this account)

Material and labour for preparation of Old wooden surfaces by removing old paint/ polish by hot air Gun machine, any number of coats and prepare the surface by scrapping with mechanical means till the surface achieve original wood finish, any width or girth complete all as specified and as directed.

Material and labour for applying resin pigment and hardener to design and colour and pattern, applying two coats of melamine polish with Poly urethyne coating to wooden surfaces using spray gun etc till fine glossy filnish is obtained including filling cracks, holes, damaged surface with filler material/ lipping patti on door shutters and frames where required complete all as specified and as as directed. (Note :- The cost of filling cracks, holes, damaged surface with filler material/ lipping patti to be included in quoted rate and nothing shall be admissible on this account)

Material and labour for preparation of old/ new surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and disposal of rubbish at location as directed. (Note :- The cost of Removal of material to be included in quoted rate and nothing shall be admissible on this account)

Material and labour for rendering 15mm thick in CM (1:6) on fair faces of brick work or concrete surfaces and finished the surface even & smooth without using extra cement all as specified and as directed.

Material and labour for rendering 5 mm thick in CM 1:3 on concrete surfaces of ceiling and finished the surface even and smooth without using extra cement all as specified and as directed.

Material and labour for Dubbing out average 10mm thick on irregular face of walls in CM 1:6 complete all as specified and directed

Dismantling of ceiling / boarding , any description, fixed in any position with nails.

Material and labour for poly vinyl chloride (PVC) false ceiling panel of size 1' x 10' long 7 to 8 mm thick with GI channel and concealed fixing arrangements to roof including necessary fixing arrangement complete all as specified and as directed. Make :- Adorn/MDG/Galaxy (Note :- (a) Border ceiling of 12" - 15" will be provided below main ceiling both Main and down border ceiling will be measured and paid flat under same item. (b) Shade/ colour of false ceiling as approved by Garrison Engineer)

Supply and fix false ceiling with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC 0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part4)-1970 and light reflectance of horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized @ 120grams per sqm including both sides) comprising of maint T runners of size 15 x 32 mm of length 3000mm, cross -T of size 15 x 32mm of length 1200mm and secondary intermediate cross T- of size 15 x 32 mm of length 600mm to form grid module of ceiling using galvanized mild steel items (galvanizing @80grams per sqm) i.e. 50mm long, 8mm outer diameter M-6 dash fastners, 6mm dia fully threaded hanger rod up to 1000mm lengrh and L-shape level adjusting of size 85x 25x 2mm.

SER. ITEM No. 16 Contd... Galvanised iron perimeter wall angle of size 24x 24x 0.40mm of length 3000mm to be fixed on periphery wall/partition with the help of plastic rawl plugs of 450mm centre to center and 40mm long dry wall wood screws. the work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge with fully perforated 12 mm thick tegular edged or 10mm thick square edged GRG false ceiling tiles. Make:- Armstrong/Lagyp or equivalent makes in list of makes as per Appendix 'A' (Note :- Design and pattern of Glass reinforced gypsum tiles to be approved by Garrison Engineer)

M & L for 10mm thick plaster of paris ceiling (Gypsum anhydrous) false ceiling including sunk or raised moulding made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish including necessary supporting hanger with 4.0 mm dia GI wire and 'J' bolts washer nuts for securing frame work to Gl frame work for (605 mm x 605 mm) seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre incl thin layer of putty with gypsum binder, sanding the sufrace till smooth surface is obtained and applying two coats of oil bound distemper over and including a coat a primer complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar rendering , bedding , removing serviceable tiles to store and disposal of rubbish at location as as directed. (Note :- The cost of Removal of material to be included in quoted rate and nothing shall be admissible on this account)

Demolition of cement concrete of any description and in any position not otherwise specially provided and disposal of rubbish at location as as directed. (Note :- The cost of Removal of material to be included in quoted rate and nothing shall be admissible on this account)

Material and labour for 40mm thick cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) as in sub base of floors all as specified and as directed.

Material and labour for dark shade Full body Vitrified tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm (600mm x 600mm) , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and as directed. Make :- Somany Techstone series or techno commercially equivalent model in makes as per list of Makes attached.

Material and labour for dark shade Full body Vitrified tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm (600mm x 600mm) , as in dado/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick backing coat in cement mortar (1:4) complete all as specified and as directed. Make :- Somany Techstone series or techno commercially equivalent model in makes as per list of Makes attached.

Material and labour for dark shad Full body Vitrified tiles 16 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm (600mm x 600mm) , in floors etc. over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) with spacers of 3 to 5 mm thick and joints to be grouted with epoxy grout complete all as specified and as directed. Make :- Somany Techstone series or techno commercially equivalent model in makes as per list of Makes attached. (Note :- The cost of spacers and epoxy grout to be included in quoted rate and nothing shall be admissible on this account)

Material and labour for dark shade Full body Vitrified tiles 16 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm (600mm x 600mm) , as in dado/skirting etc. over and including 10 mm thick backing coat in cement mortar (1:4) with spacers of 3 to 5 mm thick and joints to be grouted with epoxy grout complete all as specified and as directed. Make :- Somany Techstone series or techno commercially equivalent model in makes as per list of Makes attached. (Note :- The cost of spacers and epoxy grout to be included in quoted rate and nothing shall be admissible on this account)

Material and labour for Light shade Full body Glazed Vitrified tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 Sqm (600mm x 1200mm) , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and as directed.

Material and labour for Light shade Full body Glazed Vitrified tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 Sqm (600mm x 1200mm), as in dado/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick backing coat in cement mortar (1:4) complete all as specified and as directed.

Material and labour for Glazed coloured ceramic joint free tiles 300 x 600 x 7 to 8 mm thick on vertical surfaces such as dado/ skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick backing coat in cement mortar (1:4) all as specified and as directed.

Material and labour for joint free non skid coloured ceramic tiles 7mm to 8 mm thick (Square or rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm (600mm x 600mm) , in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile laid over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and as directed.

Material and labour for 25mm thick cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in sub base of floors all as specified and as directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons, steps , risers etc laid bedded pointed in any mortar all as specified and as directed.

Material and labour for Light/Dark shade Granite 18 to 20mm thick colour as approved by Garrison Engineer machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over and including 20 mm thick screed bed in cement mortar (1:4) complete all as specified and as directed.

Material and labour for Light/Dark shade Granite 18 to 20mm thick colour as approved by Garrison Engineer machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over and including 10 mm thick backing coat in cement mortar (1:4) complete all as specified and as directed.

Material and labour for Light/ Dark shade Granite 18 to 20mm thick colour as approved by Garrison Engineer in leather finish for top surface of steps tread, skid surface etc with three grooved lines. machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over and including 20 mm thick screed bed in cement mortar (1:6) complete all as specified and as directed.

Material and labour for Light/ Dark shade Granite 18 to 20mm thick colour as approved by Garrison Engineer machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over and including 10 mm thick backing coat in cement mortar (1:4) complete all as specified and as directed.

Material and labour for Granite 18 to 20mm thick in black leather finish for top surface of steps tread, skid surface etc with three grooved lines. machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over and including 20 mm thick screed bed in cement mortar (1:6) complete all as specified and as directed.

Material and labour for 18 to 20 mm thick Granite work (table rubbed and polished) Shade/ colour as approved by Garrison Engineer as in wash basin/ washing trough platforms, urinal partitions, etc. in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as specified and as directed.

Material and labour for 20 to 25mm thick unpolished cuddapah stone slab as in below granite stone and vertical support and like incl necessary jointing and pointing and making good to disturbed surface complete all as specified and as directed.

Material and labour for providing edge moulding semi circular shape to 18-20mm thick Granite stone of counters vanities, treads etc. including machine polishing to edge to give high gloss finish etc. complete.

Material and labour for 75 mm thick Plain Cement concrete 1:4:8 type D- 2,(using 40mm graded aggregate) as in sub base all as specified and as directed.

Material and labour for 60 mm thick, M-35 Grade glossy finish machine pressed precast conctete interlocking paver block with grey cement and pigments any shape and size confirming to IS 15658-2006 of over and including 30mm thick sand chusioning all as specified and as directed.

Material and labour for Pre-cast cement concrete solid block 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in kerb stone set in mortar 1:4 complete all as specified and as directed.

Material and labour for rough dressed sahabad stone slab flooring (30 mm thick) incl bedded and jointed in cement mortar (1:6) and pointed in CM (1:3) complete all as specified and as directed.

Dismantling boarding , any description, fixed in any position with nails.

Dismantling timber scantling, baluster, newel posts etc any section and at any position as in framed work

Supply and fix first class hardwood 35 mm wrought treads with rounded nosings, with 20 mm wrought risers on tongued both edges, glued, wedged and blocked all as specified and as directed.

Supply and fix first class hardwood Handrails moulded or shaped with splayed faces in straight lengths and fixed 100x75mm all as specified and as directed.

Supply and fix first class hardwood Caps (turned to match section of handrail and mitred in) including handrail screws and dowels (dia of cap twice the width of handrail 100x75mm) all as specified and as directed.

Supply and fix first class hardwood Scrolls to suit handrail rounded or shaped with splayed faces and fixed (dia of scroll three times width of handrail) to suilt moulded handrail all as specified and as directed.

Supply and fix first class hardwood Newel posts, wrought, with square, rounded, chamfered or stop, chamfered edges, mortices for strings and handrails, sectional area exc. 100 mm x 100 mm all as specified and as directed.

Supply and fix first class hardwood Rounded and mitred ends to tops of newels not exe 150 mm dia all as specified and as directed.

Supply and fix first class hardwood 75mm x 75mm Balusters, square wrought and fixed, with ends housed (square or splay) to handrails and treads or strings all as specified and as directed.

Supply and fix first class hardwood wall strings 40 mm thick, 20 cm wide in straight lengths. wrought one side, edges shot, housed for treads and risers, and fixed complete, including plugging to walls all as specified and as directed.

Supply and fix first class hardwood Outer strings 40mm thick, 20 cm wide in straight lengths, wrought both sides, edges shot, housed for treads and risers, tenoned at ends to fit newel posts or notched to landings, etc., and fixed complete all as specified and as directed.

Material and labour for Plugging to walls complete for second class hard wood fillets, grounds, moulding, boarding etc at distance n.exc 1 m in brick walls/stone wall/PCC block walling complete all as specified and as directed.

Material and labour for IInd class hardwood plain fillets section exc 13 Sqcm but not exc 25 Sqcm ,square,rectungular or tringular in section ,clean sawn ,secured with nails or brads for unframed work all as specified and as directed.

Material and labour for 12 mm thick ply wood grade BWR, 7 ply, type BB fixed with screws to timber frame work all as specified and as directed.

Material and labour for 3mm thick veneered 3 ply decorative ply wood, grade-I (with BWR resin) with decorative face veneers on one face fixed with fevicol to plywood work complete all as specified and as directed.

Material and labour for first class hardwood moulding, cornices plain fillets section exc 6 Sqcm but not exc 13 Sqcm , square, rectungular or triangular in section ,clean sawn ,secured with nails or brads for unframed work fixed with screws (mouldings not exc 75mm girth with carving work including) all as specified and as directed.

Material and labour for applying resin pigment and hardener to design and colour and pattern, applying two coats of melamine polish with Poly urethyne coating on new wall panelling surfaces/ wooden surfaces using spray gun etc till fine glossy filnish is obtained including filling cracks and holes with filler material as required complete all as specified and as as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.5 Sqm but n.exc. 4.0 Sqm each all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) n.exc 1.5 Sqm each all as specified and as directed.

Taking down chowkats or frames n.exc. 1.5 Sqm and refixing in the same opening after necessary repair all as specified and as directed.

Taking down chowkats or frames exc. 1.5 Sqm but n.exc. 4.0 Sqm and refixing in the same opening after necessary repair all as specified and as directed.

Material and labour for resecuring Chowkats or frames exc. 1.5 Sqm but n.exc. 4.0 Sqm exc. Without taking down all as specified and as directed.

Taking down shutters of any description n.exc. 1 Sqm each and refixing in the same opening after easing and adjusting all as specified and as directed.

Taking down shutters of any description exc. 1 Sqm and n.exc. 2 Sqm each and refixing in the same opening after easing and adjusting all as specified and as directed.

Taking down shutters of any description n.exc. 1 Sqm each all as specified and as directed.

Taking down shutters of any description exc. 1 Sqm and n.exc. 2 Sqm each all as specified and as directed.

Supply and fix first class hardwood (teak wood) plain solid straight chowkats and frames of any section or size, wrought framed, rebated in the solid, rounded or chamfered, put together with glue pinned at joints all as specified and as directed.

Supply and fix 40mm thick first class hardwood (teak wood) Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides, moulded bead to be provided and planted round the panels supplied and fitted to chowkats all as specified and as directed.

Supply and fix 30mm thick first class hardwood (teak wood) Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides, moulded bead to be provided and planted round the panels supplied and fitted to chowkats all as specified and as directed.

Supply and fix 35mm thick first class hardwood (teak wood) Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats all as specified and as directed.

Supply and fix 75 mm long Butt hinges, cast brass, with mild steel hinge pin, bright polished as per sample kept in GE's office, fixed with brass screws all as specified and as directed. all as specified and as directed.

Supply and fix 100 mm long Butt hinges, cast brass, with mild steel hinge pin, bright polished as per sample kept in GE's office, fixed with brass screws all as specified and as directed.

Supply and fix 150 mm long Brass handle, cast type, bright polished as per sample kept in GE's office, fixed with brass screws all as specified and as directed.

Supply and fix 450 mm long designed/ ornamental type Brass handle, bright polished as per sample kept in GE's office, fixed with brass screws all as specified and as directed.

Supply and fix 100 mm long Brass handle, cast type, bright polished as per sample kept in GE's office, fixed with brass screws all as specified and as directed.

Supply and fix 150 mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts as per sample kept in GE's office, fixed with brass screws all as specified and as directed.

Supply and fix 100 mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts as per sample kept in GE's office fixed, with brass screws all as specified and as directed.

Supply and fix 600 mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts as per sample kept in GE's office, fixed with brass screws all as specified and as directed.

Supply and fix 300 mm long heavy duty Brass, sliding door bolt (shape and pattern as approved by GE) with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts as per sample kept in GE's office all as specified and as directed.

Supply and fix 150mm long brass wire, type I, shutter hooks and eyes dia of wire 6mm as per sample kept in GE's office fixed with brass screws all as specified and as directed.

Supply and fix brass single coat hook 40mm to 50mm as per sample kept in GE's office fixed with brass screws all as specified and as directed.

Supply and fix 100mm long wall mounted stainless steel Magnetic door stopper as per sample kept in GE's office all as specified and as directed.

Supply and fix Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed to timber or steel/ Aluminium frame work etc. all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads all as specified and as directed.

Material and labour for Sheet glass 4 mm thick, ordinary quality and fixed to wooden frame in square n exc 0.5 sq. m in each pane all as specified and as directed.

Material and labour in repair for second class hardwood plain fillets sectional area n.exc. 3 Sq.cm , clean sawn, secured with nails or brads for unframed work all as specified and as directed.

Supply and fix Teak wood finish powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, sliding windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge

Supply and fix Teak wood finish powder coated aluminium (minimum thickness of powder coating 50 micron) work for shutters of doors, sliding windows, ventilators including providing and fixing of fittings whereever required including cost of EPDM rubber/ Neoprene gasket, rollers for sliding, locking arrangements with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge

Material and labour for first class hardwood moulded fillets sectional area n.exc. 3 Sq.cm ,clean sawn ,secured with nails or brads all as specified and as directed.

Material and labour for first class hardwood moulded fillets sectional area exc. 3 Sq.cm but n.exc. 6 Sq.cm ,clean sawn ,secured with nails or brads all as specified and as directed.

Material and labour in repair for first class hardwood moulded fillets sectional area exc. 3 Sq.cm but n.exc. 6 Sq.cm ,clean sawn ,secured with nails or brads all as specified and as directed.

Supply and fix second class hardwood plain solid straight chowkats and frame work for shelves, racks, wrought framed, rebated in the solid, rounded or chamtered, put together with glue pinned at joints all as specified and as directed.

Material and labour for 18/19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws/ fevicol to timber frame work including PVC edge band tape to match with the shade of the prelaminated particle board complete all as specified and as directed.

Dismantling of single layer of manglore/ Similar pattern tiles in roofing all as specified and as directed. Note :- Working upto the height of three storey building all as specified and as directed.

Dismantling of battens of tiles of any size and description spaced exc 15 cm, including tiling fillets all as specified and as directed. Note :- Working upto the height of three storey building all as specified and as directed.

Dismantling of unframed wk timber scantlings 40 sq. cm and over in section, in any position all as specified and as directed. Note :- Working upto the height of three storey building all as specified and as directed.

Dismantling of unframed wk timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section all as specified and as directed. Note :- Working upto the height of three storey building all as specified and as directed.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings all as specified and as directed. Note :- Working upto the height of three storey building all as specified and as directed.

Supply and fix Galvanised corrugated mild steel sheeting 0.63mm thick with two corrugations side lap, fixed with 'L' type or 'J' type of cranked hook in lieu of screws and washers in roofs, walls etc with grade of zinc coating 275. all as specified and as directed. Note :- Working upto the height of three storey building all as specified and as directed.

Supply and fix 0.63mm thick plain galvanised, mild steel sheeting as in ridge,hips,valley gutters ,drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 all as specified and as directed. Note :- Working upto the height of three storey building all as specified and as directed.

Material and labour for wrought second class hardwood in scantlings complete all as specified and as directed. Note :- Working upto the height of three storey building all as specified and as directed.

Material and labour for clean sawn ,second class hardwood tile battens at 30cm centres, exe 5 and n.exe 15 sqcm sectional area all as specified and as directed. Note :- Working upto the height of three storey building all as specified and as directed.

-Ditto- all as item above, but except battens, by using old serviceable battens. Note :- Working upto the height of three storey building all as specified and as directed.

Material and labour for preparing tile battens of any size and spacing and treated all over (measured overall on one side only spaces not deducted) with two coats of cresoting oil etc all as specified and as directed. Note :- Working upto the height of three storey building all as specified and as directed.

Material and labour for providing roof tiles Manglore pattern interlocking at side joints, laid dry,all as specified and as directed. Note :- Working upto the height of three storey building all as specified and as directed.

-Ditto- all as item above, but except tiles, by using old serviceable tiles. Note :- Working upto the height of three storey building all as specified and as directed.

Material and labour for ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in CM (1:6) all as specified and as directed. Note :- Working upto the height of three storey building all as specified and as directed.

-Ditto- all as item above, but except tiles, by using old serviceable ridge or hip tiles. Note :- Working upto the height of three storey building all as specified and as directed.

Material and labour for preparation surface of old roof tiles (manglore tiles ) and applying two coats of water based exterior emulsion paint with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI. Allow 6-8 hrs to dry the surface in both the coats of paint all as specified and as directed. Note :- Working upto the height of three storey building all as specified and as directed.

Excavation in post holes (or similar holes) each n.exc 0.5 cum as in Hard and dence soil and getting out and removing surplus soil to a distance n.exc 50m all as specified and as directed.

Material and labour for PCC 1:2:4, type B-2 (40 mm graded stone aggregate) in foundation, Post holes all as specified and as directed.

Supply and fix rolled sections as in main and cross beams, hips and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc Fe-410-W (Gde E-250) Quality A all as specified and as directed.

Supply and fix for MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment Fe-410-W (Gde E-250) Quality A all as specified and as directed.

Supply and fix pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering /cladding to wall fixed with self tapping screws /L hooks or J types or cranked bolts all as specified and as directed.

Excn in trenches n.exc. 1.5 mtr wide & n. exc. 1.5 mtr deep in hard/dense soil & getting out all as specified and as directed.

Material and labour for PCC (1:4:8) type D-2, using 40mm graded stone aggregate as in foundataion filling & mass concrete all as specified and as directed.

Material and labour for brickwork with Old size fly ash' bricks straight or curved on plan exc 6 m mean radius in CM (1:6) all as specified and as directed.

Material and labour for brickwork with Old size fly ash' bricks straight or curved on plan to any radius in half brick thick wall built in CM (1:4) all as specified and as directed.

Returning, filling in including spreading, levelling watering & well ramming in layers n.exc. 25CM thick in hard/dense soil all as specified and as directed.

Removing excavated material n.exc.50 Mtr & depositing where directed at a level n.exc.1.5Mtr above the starting point all as specified and as directed.

Material and labour for 100 mm thick plain cement concrete 1:4:8 type D2 (using 40 mm graded aggregate) as in sub base of floor all as specified and as directed.

Material and labour for 100 mm thick plain cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in floor all as specified and as directed.

Material and labour for 40 mm thick DPC in PCC type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) to horizontal or vertical surfaces including necessary formwork all as specified and as directed.

Material and labour for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement all as specified and as directed.

Supply and fix steel windows with side hung shuter including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars. all as specified and as directed.

Surface excavation n.exc 30cm deep & averaging 15 cm deep and getting out in Hard / dense soil all as specified and as directed.

Material and labour for hard core broken stone or boulders n exc 63mm deposited spread and levelled in layers n exc 15cm thick watered and rammed to a true surface all as specified and as directed.

Material and labour for 75 mm thick Plain Cement concrete 1:3:6 type C- 2,(using 40mm graded aggregate) as in plinth protection all as specified and as directed.

Demolition of brick work or stone boulder masonry built in cement motar including all quoins, arches, pillers etc, but exc ashlar facing, dressed stone work and precast concrete articals and disposal of rubbish at location as as directed. (Note :- The cost of Removal of material to be included in quoted rate and nothing shall be admissible on this account)

Material and labour for walling of random rubble masonary, uncoursed well bonded, bedded and solidly hearted built in cement mortar (1:6) all as specified and as directed.

Extra over stone walling Granite or trap stone 20mm for hammer dressing to face stones and dressing of face beds and joints as specified, of random rubble walling, uncoursed or brought upto courses all as specified and as directed.

Supply and fix heavy duty stainless steel ceiling mounted cloth hanger 6 pipe x 8 feet long of weight 5.5 kg complete all as specified and as directed.

Supply and fix Window 36”-66” Extendable Double Curtain Rod with Brackets for Door & Windows Adjustable Length Heavy Duty Iron Dual Telescopic Drapery Pole with Half Round Finials 19mm Diameter, Satin Silver or as approved by Engineer in charge.

Providing and fixing 12 mm thick frameless double leaf toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight up to 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. and making necessary holes etc. for fixing required door fittings and lock, all complete as per direction of Engineer in charge Note : (Door handle,lock and stopper etc. will be measured and paid separately).

Supply and fixing 12 mm thick crystal or polished thoughened glass as in partition (design will be approved at the time of execution) secured with stainless steel bracket (make "Ozone") supported and required coloured pvc film fixed with approved adhesive as per manufacturer’s instruction on one face complete all as speciifed and directed by Engineer in charge

Providing etching to 12 mm thick toughened glass by mechanical/manual means and making approved design/pattern/logo all complete as per direction of Engineer in charge. (Note: total area of glass shall be measured for payment)

Supply and fixing stainless steel door handles of size 300 mm of approved make complete as per direction of Engineer in charge

Supply and fixing stainless steel door lock of approved make complete as per direction of Engineer in charge

Material and labour reinforced cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in Beams, cantilevers, bressummers, lintels and the like all as specified and as directed.

Material and labour for precast cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) set in CM (1:4) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces e all as specified and as directed.

Material and labour for TMT bars 10mm dia & over cut to length bent to shape required including, cranking binding with & including MS wire not less than 0.90m dia or securing clips all as specified and as directed.

Material and labour for TMT bars 6 to 8mm dia & over cut to length bent to shape required including, cranking binding with & including MS wire not less than 0.90m dia or securing clips all as specified and as directed.

Material and labour for formwork to to sides and soffits of floor or roof beams, beam haunch ings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. surface of concrete. all as specified and as directed.

Providing and fixing stainless steel (Grade 304) stair/railing/Duct /grating /drain with cover made of channels, plates,angles etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the duct with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the wall and floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) all as specified and as directed.

Material and labour 75 mm plain cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) as in sub base or simillar work all as specified and as directed.

Supply only intergal water proofing compound

Material and labour for carrying out water proofing treatment to sunken slab, floors and wall of WC, WHB and urinals, as mentioned below :- (a) Special tratment to toilet floor by demolition of existing treatment of any description and thickness,removal rubbish outside MD land (b) Clean the floor surface throughly to remove laitance, dirt, dust, etc (c) Form angle fillet of size 40 mm x 40 mm along the junction of wall and floor using polymer modified mortar ("Dr Fixit" Pidicrete URP" or eqvt). (d) Sanitary pipes entering through walls and floor shall be sealed with "Dr Fixit Bathseal Tape" and the gaps to be grouted with non-shrink cementitous grout "Dr Fixit Bathseal Grout" or eqvt. Nahani traps, etc to be fitted securely and the gaps around it to be grouted in the same manner. (e) Apply one coat of a cementitious-modified polymer coating "Dr Fixit Bathseal Plus" or eqvt on all angle fillets by brush and cover it with 100 mm open woven mesh when it is still wet. Apply second coat of the same coating on the angle fillets and allow it to dry completely.

Ser. ITEM NO. 149 Contd... (f) In the remaining area, in dry sustrate condition brush apply first coat of the same coating and further apply second coat when first coat is dry. Extend the coating upto 150 mm above the FFL. (g) After 2 to 3 days, floor portion must be overlaid with a 25mm thick concrete screed M-15 type B-0 mxed with integral WPC incl flll up the sunken portion with lean concrete 1:5:10 type E2 etc complete all as per manufacturers instruction and all as specified and as directed. Note:- for activities (a) to (g) only floor area will be measured under the item and nothing shall be paid separately.

Material and labour for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surfaces mixed with WPC as per manufacturer's instructions and finishing the surface even & smooth without using extra cement all as specified and as directed. Note:- Water proofing compound will be measured and paid separately

Material and labour for 20 mm average thickness of screed layer on RCC slab in cement mortar (1:4) mixed with WPC as per manufacturer's instructions complete all as specified and as directed. (Note :- Water proofing compound will be measured and paid separately)

Material and labour for preparation of floor/ wall surfaces and applying 2 coats of polymer modified mortar food grade of make Dr Fixit pidifin 2K / Home shield Latex shield 2K/ or any approved make on an interval of 6 hrs. all as specified and as directed.

Cutting chases, pinning in, making good to facing where reqd and pointing in cement mortar 1:3 to ends or edges of landings, steps , lintels etc and cutting chases for concealed water tubing,Electric line/concealed wire etc and making good, cutting exe 10cm but n.exe 20cm girth all as specified and as directed.

Supply and fix Stainless steel soap dish holder of grade 304 all as specified and as directed. (Make : Cera Cat No F5003106 or equivalent model in makes as per list of make attached )

Supply and fix in repair Stainless steel single towel rail 600 mm long of grade 304 all as specified and as directed. (Make : Jaquar Cat No ACN-1111SM or equivalent model in makes as per list of make attached )

Supply and fix Stainless steel towel Ring round with round flanges of grade 304 all as specified and as directed. (Make : Jaquar Cat No ACN-1121BN or equivalent model in makes as per list of Makes attached)

Supply and fix Stainless steel double coat hook of grade 304 all as specified and as directed. (Make : Jaquar Cat No AKP-35761P or equivalent model in makes as per list of Makes attached)

Supply and fix in repairs , 25mm dia heavy duty sainless steel pipe of grade SS-304 for door/window curtain rods all as specified and as directed.

Supply and fix heavy duty fancy type stainless steel brackets of grade SS-304 (shape/ pattern approved by Garrison Engineer ) suitable for 25mm dia curtain rod all as specified and as directed.

Taking down up or down steel tubing and connections 15mm dia pipes complete all as specified and as directed.

Taking down up or down steel tubing and connections 20mm dia pipes complete all as specified and as directed.

Taking down up or down steel tubing and connections 25mm dia pipes complete all as specified and as directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors 16 mm outer diameter complete all as specified and as directed. Note - The rates coated includes all plain CPVC fittings mean fittings which do not have any metal component and is jointed with CPVC solvent cement only (Elbow, Tee, socket, Reducer, Bushing, Step over bends, End cap, End plug etc. )

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors 20 mm outer diameter complete all as specified and as directed. Note - The rates coated includes all plain CPVC fittings mean fittings which do not have any metal component and is jointed with CPVC solvent cement only (Elbow, Tee, socket, Reducer, Bushing, Step over bends, End cap, End plug etc. )

“Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors 25 mm outer diameter complete all as specified and as directed. Note - The rates coated includes all plain CPVC fittings mean fittings which do not have any metal component and is jointed with CPVC solvent cement only (Elbow, Tee, socket, Reducer, Bushing, Step over bends, End cap, End plug etc. )

Supply and fix brass elbow fittings for 16 mm CPVC pipe laying in wall /ceiling of laying in floor complete all as specified and as directed.

Supply and fix brass elbow fittings for 20 mm CPVC pipe laying in wall /ceiling of laying in floor complete all as specified and as directed.

Supply and fix brass elbow (3/4 x ½) fittings for 20 mm CPVC pipe laying in wall /ceiling of laying in floor complete all as specified and as directed.

Supply and fix brass tee fittings for 16 mm CPVC pipe laying in wall /ceiling of laying in floor complete all as specified and as directed.

Supply and fix brass tee fittings for 20 mm CPVC pipe laying in wall /ceiling of laying in floor complete all as specified and as directed.

Supply and fix Male brass threaded adaptor (MTA/MBTA) fittings for 16 mm CPVC pipe laying in wall /ceiling of laying in floor complete all as specified and as directed.

Supply and fix female brass threaded adaptor (FTA/FBTA) fittings for 20 mm CPVC pipe laying in wall /ceiling of laying in floor complete all as specified and as directed.

Supply and fix union fittings for 25 mm CPVC pipe laying in wall /ceiling of laying in floor complete all as specified and as directed.

Supply and fix Ball valve fittings for 25 mm CPVC pipe laying in wall /ceiling of laying in floor complete all as specified and as directed.

Supply and fix in repairs for Wall Mixer with provision for overhead shower with 115mm long bend pipe on upper side, connecting legs and wall flanges fixed in wall screwed ends for iron pipe or for union and fixed for 15mm bore of pipe with long shank all as specified and as directed. (Make : Jaquar Cat No CON-273KNUPR or equivalent model in makes as per list of Makes attached)

Supply and fix in repairs for bib cock with wall flange fixed in wall screwed ends for iron pipe or for union and fixed for 15mm bore of pipe with long shank all as specified and as directed. (Make : Jaquar Cat No FUS-29037 or equivalent model in makes as per list of Makes attached)

Supply and fix in repairs for providing two way bib cock with wall flange copper alloy fancy type screwed down high pressure with cruntch or butterfly handle, screwed both ends for iron pipe or for union and fixed for 15mm bore of pipe with long shunk and cup all as specified and as directed. (Make : Jaquar Cat No CON-041KN or equivalent model in makes as per list of Makes attached)

Supply and fix in repairs for Chromium plated Wall mounted Shower arm 160mm long light body round shape with flange all as specified and as directed. (Make : Jaquar Cat No SHA-477 or equivalent model in makes as per list of Makes attached)

Supply and fix in repairs for overhead Shower of 100 mm dia round shape Single flow (ABS body chrome plated with gray face plate) with Rubit cleaning system (Make : Jaquar Cat No OHS-1989 or equivalent model in makes as per list of makes attached)

Supply and fix in repairs Hand shower (health faucet) with 1 meter long easy flex tube in chrome finish & Wall hook all as specified and as directed. (Make : Jaquar Cat Part No. ALD-565 or equivalent model in makes as per list of makes specified)

Supply and fix in repair 15mm Bib taps with Nozzle and wall flange for washing machine, fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and as directed. (Make : Jaquar Cat No CON-049NKN or equivalent model in makes as per list of Makes attached)

Supply and fix in repair 15mm Pillar taps, fancy type, cast copper alloy, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed all as specified and as directed. (Make : Jaquar Cat No CON-011KN or equivalent model in makes as per list of Makes Attached)

Supply and fix in repairs Central hole basin mixer without popup waste system with 450 mm long braided hoses fixed to 15mm bore of pipe all as specified and as directed. (Make : Jaquar Cat No CON-167KNB or equivalent model in makes as per list of makes attached)

Supply and fix 25mm ball valves, high pressure, of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe & fixed ( Minimum weight 25mm-455gms) all as specified and as directed.

S&F in repairs Vitreous china wash down water closet (Pedestal pattern) with P or S trap , white in colour including fixing bolts, connection to drain and to flushing pipe with low level PVC valve less symphonic action type flushing cistern of 10ltrs capacity white in colour with inlet, ball valve float and PVC flush pipe 32mm dia with white seat cover, closed pattern with flat bottom and cover and mild steel chromium plated or hinging device complete all as specified and as directed. (Make : Jaquar/ Cera/ Hindware or equivalent makes as per list of makes attached)

Supply and fix in repair Vitreous china wash hand basin of size 605 x 410 x 200 mm size, including cutting granite and cuddapah under counter and fixing but exclusive of fixing of supply and waste pipe /bottle trap ,taps,waste ,chain and plug and porcelain stopper all as specified and as directed. (Make : Jaquar Cat No FNS-WHT-40701 or equivalent model in makes as per list of makes attached)

Supply and fix in repair vitreous china urinal (Top inlet) of size 345 x 320 x 610mm (excluding flushing cistern, flush pipe , waste coupling and waste pipe) including fixing arrangments all as specified and as directed. (Make : Jaquar Cat No URS-WHT-13257 or equivalent model in makes as per list of makes attached)

Supply and fix in repairs for providing angular stop cock cast copper alloy with wall flange screwed down high pressure with cruntch or butterfly handle, screwed both ends for iron pipe or for union and fixed for 15mm bore of pipe all as specified and as directed. (Make : Jaquar Cat No CON-059KN or equivalent model in makes as per list of makes attached)

Supply and fix in repairs 32 mm dia Waste coupling of stainless steel half thread with 80mm height all as specified and as directed. (Make : Jaquar Cat No ALD- 709 or equivalent model in makes as per list of makes attached)

Supply and fix 32 mm dia of bore bottle trap of PTMT having minimum water seal of 25 mm (Minimum weight 32 mm-260gms/40mm-270 gms) all as specified and as directed.

Supply and fix concussive push butten taps chromium plated of cast copper alloy auto closing system with built in control cock with wall flange and discharge pipe screwed for iron pipe 15 mm bore all as specified and directed by Engineer Incharge. (Make : Jaquar Cat No PRS-077 or equivalent makes as per list of makes attached)

Supply and fixing of Toilet Paper Holder with flap stainless steel all as specified and as directed. (Make : Jaquar Cat No ACN-1153S or equivalent model in makes as per list of makes attached)

Supply and fix PVC connections 15 mm size with PTMT nuts of length 450mm all as specified and as directed.

Dismantling of cast iron 100 mm bore pipes jointed in cement motar all as specified and as directed.

Dismantling of cast iron 75 mm bore pipes jointed in cement motar all as specified and as directed.

Supply and fix 110 mm bore PVC (SWR) type B pipes single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and as directed.

Supply and fix 75 mm bore PVC (SWR) type B pipes single socketed, in any length with rubber ring joints, fixed to floor/wall complete all as specified and as directed.

Supply and fix 50 mm bore PVC type B pipes single socketed, in any length with rubber ring joints, fixed to floor/wall complete all as specified and as directed.

Supply and fix 40 mm bore PVC type B pipes single socketed, in any length with rubber ring joints, fixed to floor/wall complete all as specified and as directed.

Supply and fix 110mm bore PVC (SWR) bends all as specified and as directed.

Supply and fix 110mm bore PVC (SWR) bends with access door complete all as specified and as directed.

Supply and fix 110mm bore PVC (SWR) branch piece, single (single Y) equal or unequal all as specified and as directed.

Supply and fix 110mm bore PVC (SWR) branch piece, single (Double Y) equal or unequal all as specified and as directed.

Supply and fix 110mm bore PVC (SWR) junction single (Single T) equal or unequal all as specified and as directed.

Supply and fix 110mm bore PVC (SWR) reducers all as specified and as directed.

Supply and fix 75mm bore PVC (SWR) bends all as specified and as directed.

Supply and fix 75mm bore PVC (SWR) bends with access door complete all as specified and as directed.

Supply and fix 75mm bore PVC (SWR) branch piece, single (single Y) equal or unequal all as specified and as directed.

Supply and fix 75mm bore PVC (SWR) junction single (Single T) equal or unequal all as specified and as directed.

Supply and fix 50mm bore PVC bends all as specified and as directed.

Supply and fix 50mm bore PVC junction single (Single T) equal or unequal all as specified and as directed.

Supply and fix 50mm bore PVC reducing bush all as specified and as directed.

Supply and fix 40mm bore PVC bends all as specified and as directed.

Supply and fix 40mm bore PVC junction single (Single T) equal or unequal all as specified and as directed.

Supply and fix 110mm bore PVC (SWR) floor trap, plain including jointing with solvent cement all as specified and as directed.

Supply and fix 110mm bore PVC (SWR) Multi floor trap, plain including jointing with solvent cement all as specified and as directed.

Supply and fix Grating square fitting of size 150mm made in two parts for smell and mosquito proofing with minimum 25 mm water seal of PTMT. (Minimum weight 85gms ) all as specified and as directed. (Make : Jaquar,cera or equivalent as per list of makes attached)

Supply and fix 110mm bore PVC (SWR) vent cowl all as specified and as directed.

Supply and fix 75mm bore PVC (SWR) vent cowl all as specified and as directed.

Material and labour for core cutting of 150mm dia, n exc 600mm depth in stone wall/ RCC Slab and making good disturbed surfaces and filling the remaining area with cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate all as specified and as directed.

Material and labour Aluminium Compostie panel in metalic/glossy colour of approved shade, cut to shape required made out of 3mm thick aluminium composite panel material comprising of 2.5 mm thick FR grade mineral core sandwiched between two aluminium sheets (each 0.25 mm thick) using stainless steel screws , nuts , bolts, washers, cleats, weather silicon sealant, backer rods etc all as specified and as directed.

Supply and fix Anodised aluminium frame work for ACP panel and like with one or more rebates, screw, anchor bolt, joining cleat etc. complete all as specified and as directed.

Supply and installation of High pressure laminated partitions as in shower cubicle partitions and urinal partitions, etc as per site requirement , (Height is including 100 mm gap from bottom, Door Width- 600 mm ). Made from solid grade compact high pressure laminate as per IS:2046 and EN-438 manufactured under high specific pressure > 5 MPa and temperature >120°C, All doors will be of single colour and made of 12 mm thick Merino HPL compact panel. The doors will have chamfered edges. Each door will be supported by 3 stainless steel made hinges affixed to the pilasters. Size of panels to be as per drawing. HARDWARE & ACCESSORIES are H shaped (Top) head frame structure made of extruded Aluminium grade 6063 T5-50 micron epoxy powder coated for surface protection, Size to be 125x70x5T. Corner joinery section, Size to be 40x16.5x1.8T. U-Channel Wall joinery section,Size to be 22x16x1.6T. Door stopper section, Size to be 21x12.5x1.6T. Spring loaded Butt Hinges made from Stainless steel grade 304. Surface finish to be matt type. Covers to be lacor coated.etc complete all as specified and as directed.

Material and labour for Water proofing treatment to RCC roof slab, walls, chhajjas etc,and shall be carried out as specified below and as directed by Engineer-in-Charge. (a) Preparing plastered surfaces of roof slab, walls, chhajjas etc, by brooming with broom sweeping free from dirt dust etc & evenly applying evenly a coat of approved bituminous primer @ 0.50 Kg/sqm of area. (b) Providing APP polymer modified approved membrane, non woven, polyester, weighing not less than 3.5 Kg/sqm with laps & overlaps as specified & joints sealed and applied complete by torch application method all as specified & directed by Engr-in-Charge. Carrying out test by flooding water for 24 hrs for leakage & seepages and rectifying the same to the entire satisfaction of GE. (c) Finally applying a coat of solar reflective bituminous aluminium paint @ 0.15 ltr/sqm on the top of membrane surfaces complete all as specified and as directed.

Dismantling structural steel work including doors, gates, etc all as specified and as directed.

Supply and fix mild steel rolled sections as in framing for cladding, brackets, glazing and the like fixed with angle cleats and connecting plates including welding angles, as necessary,bending and gusset plates, riveting, etc, conforming to Fe.290.Gde-E-165 all as specified and as directed., etc

Supply and fix 1.25 mm thick Mild steel, plain, black sheet in water tanks , water trough , ducts , covers and similar work, cut to size, holes punched; including round headed screws,clout nails or rivet sand fixed to wood orsteel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required all as specified and as directed.

Material and labour for preparation of new steel surface and applying two coat of synthetic enamel paint over a coat of red oxide all as specified and directed by Engineer in charge

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.and making good disturbed surfaces of walls, floors, etc.

M&L for point wiring (Concealed wiring) of any length using approved colour coding as per IS, with multi stranded copper conductor 1.5 Sqmm (Nominal area), single core, PVC insulated and unsheathed stranded FRLSH cable 1100 volts grade, in PVC rigid conduits heavy duty, medium grade, ISI marked (Min 20mm dia ) with valid CML No, totally concealed in wall/floor and casing capping along roof /ceiling including all accessories as required complete including GI Metal Flush boxes with modular frame/cover plate of suitable size for mounting modular switches/sockets etc. and PVC insulated multi stranded FRLSH copper conductor 1.5 Sq.mm single core cable (Green colour) as earth conductor and connecting to common earth dolly complete all as specified and directed by E in Charge for the following:-

(a) One light point controlled by one switch one way type (including 36 Points for strip lighting)

(b) One Ceiling fan/Exhaust fan point controlled by one switch one way type

(c) One 3 pin 5 Amps socket outlet point on Same board

(d) One 3 pin 5 Amps socket outlet point on independent board

(e) One bell/buzer point controlled by one bell push complete all as specified.

Note for Item Sr No 231.00 to 231.05 - (i) Cutting in chases and pointing in brick wall/Stone Wall will be done by contractor without any extra cost. (ii) Making good of distrubed surfaces matching with existing finishes will be done by contractor without any extra cost. (iii) Contractor shall make the surface good after flushing the sunken box as existing without any extra cost (iv) Contractor shall provide circuit wiring with 3 x 2.5 Sqmm copper wire from DB to switch board and rate for the same is deemed to be included in unit rate of item. (v) Length of point Wiring for light points/ fan points (ceiling/ exhaust / wall) shall be of suitable length as per site requirement and location of fittings and their switches as directed by Engr-in-charge. The cost of same shall deemed to be included in quoted rates.)

All as per item No 231.00 above but with 2.5 sq mm copper conductor FRLSH (multistrand), 1100 volts grade PVC insulated, ISI marked unsheathed cable in and including concealed PVC conduit, heavy duty ,ISI marked, medium grade with valid CML No not less than 25 mm dia with all fitting & accessories as required and including PVC insulated ISI marked, unseathed, FRLSH copper conductor cable of size 2.5 sq mm (Green Colour) as earth wire to common earth dolly all as specified and directed, for one three pin socket outlet 15 Amps.

All as per item No 231.00 above but with 4.0 sq mm copper conductor, FRLSH (multistrand), 1100 volts grade, PVC insulated ISI marked, unsheathed cable in and including concealed PVC conduit, heavy duty ,ISI marked, medium grade with valid CML No not less than 25 mm dia with all fitting & accessories as required and including PVC insulated ISI marked, unseathed, FRLSH copper conductor cable of size 4.0 sq mm (Green Colour) as earth wire to common earth dolly all as specified and directed,, for one AC unit 16/20 Amps.

Supply and fix modular switch, one way, 6 Amps, one module complete all as specified and as directed.

Supply and fix modular socket 6 Amps 2/3 pin, two module complete all as specified and as directed.

Supply and fix modular switch, one way, 16 Amps, one module complete all as specified and as directed.

Supply and fix modular socket 6 Amps /16 Amps 2/3 pin two module complete all as specified and as directed.

S & F 240 V, Single pole and neutral enclosure with a two pin and earth plug and socket complete with one 20 amp single pole MCB `C` curve, 10 KA, including metal plug top (2P+E) complete all as specified and directed

Supply and fix ceiling rose, 3 terminals / PVC / Polycarbonate, isolated body complete all as specified and as directed.

Supply and fix modular bell push, 6 Amps, 1 Module complete all as specified and as directed.

Supply and fix call bell electric, ding dong type, including hard PVC board ISI marked complete all as specified and as directed.

S & F Modular stepped type electronic fan regulator 2 Module (for energy saving BLDC Fan) all as specified & directed.

Supply and fix modular RJ45 connector socket Cat 6, one module complete all as specified and as directed. (Note : Make for Ser. Item No. 234.00 to 237.00, 240.00, 242.00 and 243 above : Make of Modular switch, sockets, bell push and other accessories like cover plate etc. shall be of same make. Contractor shall submit the sample and take approval from GE before procurement)

Supply and fix Passive Infra Red (PIR) occupancy Motion Sensor Ceiling Mounted type ,area of detection minimum 7 Meter, 360 degree, 230 Volts, 50Hz complete all as specified and directed. (Make : Wipro Cat Part No. GLPS01S010A or equivalent in as per list of makes attached)

Supply only Control Remote suitable for PIR Motion Sensor as catered in item No 244 above including providing suitable batteries in remote complete all as specified and as directed, (Note : Make of PIR motion sensor and remote control shall be of same make.)

S&F LED 10 Watts light fittings (Mirror Light) surface/ wall mounted, LED batten with polycarbonate housing & integrated electronic driver, colour temp 6500 K complete including all accessories as required for mounting/ fixing the light fitting and including twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector of light fitting all as directed. (Make - Luker - Cat Part No LUMOSECCO 2 Feet LT510P or equivalent in Crompton Cat Part No. CCS-103-10-65-SL-DP-NWH and Wipro Cat Part No.LL20-111-XXX-65NE3.)

S & F LED Tube light fitting 20/22 Watt, Surface and wall mounted LED batten, Polycarbonate housing provided for efficient heat dissipation with polycarbonate diffuser, heavy duty driver, 20/22 W LED, colour temp 6500 K, complete including all accessories internally pre-wired and including connecting up with three core sheathed flexible copper conductor cable of suitable size from ceiling rose to connector of light fittings. Make - Luker - LUMOS PRIMO Aluminium tube set-LT-522 or equivalent in Crompton Cat Part No. CCS-100-20-65-HLS2-DP-NWH and Wipro Cat Part No.LL20-221-XXX-65AL1

S & F Wall mounted Focus light 12W LED luminaire in powder coated white in round profile with optimized heat sink for efficient heat dissipation of 12W LED warm white color temperature etc. prewired and including all accessories complete all as specified and directed. Make -Luker - LCOBSP 12(Corvus surface COB 36Deg) or Equivalant in as per list of makes attached) .

S & F Round recess (AI) down light 15 W, recess mounted aluminium die - cast LED luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation of 15W LED downlighter of white/neutral white 6500K color temperature etc. prewired and including all accessories complete all as specified and directed. (Make - JAQUAR - LNEP01R015XC or equivalent in Luker model No. LNPR15(WH); Halonix cat Part No. HLDLR – R-06 – 15 – CW)

S & F surface mounted LED Panel light 40 W LED of size 600mm x 600MM x 35mm, 240Volts, colour temp 6500 K with glare free symmetrical illumination suitable for ceiling, Environmental friendly, new generation, energy saving, high power LED as a light source with clear diffuser and separate replaceable electronic driver including connecting with twin core wire, all acessories as required for fixing the light fitting and matching to the adjacent ceiling surfaces all as specified and directed. (Make : Cat Part No. Luker Model No. LNPSRS 40 (IRIS surface panel) or equivalent in Halonix Cat Part No. HLFPS22-06-40-CW or equivalent in other approved Make)

S & F Recess mounted LED Panel lights 42/45 Watt LED of size of 1200mm x 300mm, 240Volts, 6500 K colour temperature with glare free symmetrical illumination suitable for ceiling, environmental friendly, new generation, energy saving, high power LED as a light source with clear diffuser and separate replaceable electronic driver including connecting with twin core wire, all acessories as required for fixing / hanging the light fitting and matching to the adjacent ceiling surfaces all as specified and directed.. Make : Jaquar - LSVR03S042XC or equivalent in Luker - LKM4145 and Philips – RC380B LED 42S – 6500 G5L3W12PSU OD

Supply and fix 12W LED light fitting adjustable spot light recessed mounted (buried in walls/ceilings ) beams made of extruded Aluminium powder coating, High power high lumen LED, compact robust non corrosive aluminium body min 100 lm/W efficacy all as per OEM recommendations including all acessories as required and connection cable complete all as specified and as directed. Make - Jaquar - Model No LERS03R012XN / LUKER Model No - LCOB12N

Supply and fix LED Strip Cove Lights prewired and all accessories including fixing arrangements in false ceiling or any other celing etc. incl LED driver complete all as specified and directed. Make :- Havells Cat No. LHEHDLP7UN1W024 or equivalent in Philips Cat No. LED Strip Sky Cove 5M WW with driver and JAQUAR Cat No.– LSTP 03X005XW

Supply and fix Picture light 07 Watt, LED Wall Picture Light 07 Watt, warm-white light, color temp 3000k, individual LED lenses, bronze coloured flexible neck for adjusting beam complete all as specified and as directed. Make: As per Sample kept in GEs office. Note : Contractor has to take the sample from subdivsion and also take approval of GE before procurment of light.

Supply and fix LED Step light fitting 3 Watt fixed in stair steps made of extruded aluminium, powder coating, high power, high lumen LED, compact robust non corrosive aluminium body, dust tight with effective thermal managment complete all as per OEM recommendations incl all acessories for fixing the light complete all as specified and as directed. Make - Jaquar - LFTL01S003XW / Luker - LODFTG3 or equivalent as per list of makes attached)

Supply and fix LED Ceiling mounted down (Dome) light fitting 30 Watt minimum dimension 225 mm x 35 mm, surface type circular, IP 65 including all required accessories , fixing arrangements and connecting with twin core copper wire from light source to light fitting complete all as specified and directed. Make - Luker - LOR65-30N or equivalent model/ design and specifications in as per list of makes attached)

Supply and fix 30W LED Orbit Suspended round shape luminaire light fitting fixed in ceilings made of extruded aluminium powder coating, high power high lumen LED, compact robust non corrosive aluminium body all as per OEM recommendations complete all as specified and as directed. Make - Luker LHL301or equivalent model / design and specifications in other approved makes.

Supply and fix decorative hanging wall light fitting pendant type, black finish, high power high lumen LED ( including 5Watt LED lamps), compact robust non corrosive aluminium body Dimesnsion - 375mm x 165 mm all as per OEM recommendations incl all acessories for fixing the light complete all as specified and as directed. Make - Luker - LWLA2E27 BK or equivalent model / design and specifications in as per list of makes attached)

Supply and fix decorative wall light fitting pendant type, gold finish, high power high lumen LED ( including 5 Watt LED lamps), compact robust non corrosive aluminium body all as per OEM recommendations complete all as specified and as directed. Make - Luker - LWLA2E27 AG or equivalent in Havells - FLORETTE WL 1LS E27 SS Decorative wall or equivalent as per list of makes attached)

S&F LED Security light fittings 72 Watt with PDC housing, IP 66 complete with all accessories such as MS Clamp, nut, bolts, GI mounting bracket of length upto 1.5 mtr etc. prewired, connecting light fitting to light source with three core wire all as specified and directed. Make - Luker LST - 72(STRADA Street Light) or equivalent in Havells - ENDURASUNDOWNSL72WLED765PASYBOTG. and Halonix HLSLD-ML04-72-CWL-HL2-P

Material and labour for PVC conduit medium grade, concealed type not less than 25 mm dia including all accessories as required in installation for laying existing LAN/ CAN/ TV/ Internet cables of any type all specified and as directed. NOTE :- (i) Cutting in chases and pointing in brick wall / stone wall shall be done by contractor without any extra cost. (ii) Making good of disturbed surfaces matching with existing finishes shall be done by contractor without any extra cost

Dismantling, disonnecting and taking down the ceiling fan / exhaust fan carefully and depositing to MES Store complete all as specified and as directed.

Supply and fixing BLDC ceiling fans 1200 mm sweep complete with blades, down rod of adequate length (of suitable length so that distance between floor and bottom of ceiling fan should be min 260cm) with accessories like canopy, nut, bolts, shanks and shackle etc, 230V, single phase, 50Hz AC, suitable to operate with input voltage 120V to 300V, PF-min 0.95, double ball bearing, 1200mm sweep, min air delivery, 210 cubic meter per min (CMM), 28 Watt, Min 350 RPM, Insulation Class 'B', Min 3 Years OEM warranty with service value 6.00, BEE Five star rated with brushless direct current motor (BLDC), white colour complete including making electric connectionby providing 1.0 Sqmm x 3 core flexible sheathed copper cable from ceiling rose/ source to fan connector. Make : Crompton/ Havells/ USHA

S & F exhaust fan made of sturdy engineering plastic of sweep 300 mm with louver, single phase suitable for 230 volts, 50 HZ, RPM and air delivery shall not be less than 1200 RPM, air deilvery 1125 CMH and connecting up complete including making electric connection by providing 1.0 Sqmm x 3 core flexible sheathed copper cable from ceiling rose to connector of fan incl all acessories complete all as specified and directed .

S & F heavy duty industrial wall fan (Steel Body ), Air circulator of 750 mm sweep with single phase suitable for 230 volts, 50 HZ, 1440 RPM, air delivery shall not be less than 24000 CMM , 250Watt, wall mounted , 3 blade and connecting up complete including making connection by providing 1.5 Sqmm x 3 core flexible sheathed copper cable from ceiling rose to connector of fan incl all acessories complete all as specified and directed . Make : Almonard – Almonard 30 inch 750 mm air circulator or equivalent in Havells : Turboforce wall 750 mm and Bajaj : Supreme plus air circulator 750mm

Taking down carefully Copper/ Aluminium sub main wiring of any type and size including all accessories wire, casing & caping/ conduit, screws etc and making good disturbed surfaces complete as specified.

M&L for concealed Sub main wiring with two single core PVC insulated unsheathed cable 1100 volts grade, 4 Sqmm size with multistranded copper conductor, FRLS-H cable drawn in but including through concealed conduit, including PVC conduit medium grade, heavy duty, ISI marked not less than 25 mm dia, in any type of wall, roof, etc, with all connected fittings , including PVC insulated unsheathed 4.0 Sqmm FRLS-H cable with multistranded copper conductor of green colour as continuous earth conductor cable connected to earth dolly and make good to match with the existing surfaces after completion all as specified. Note- (i) Cutting in chases and pointing in brick wall/Stone Wall or any type of surface for concealing the conduit shall be done by contractor without any extra cost. (ii) Making good of distrubed surfaces matching with existing finishes shall be done by contractor without any extra cost (iii) Two runs of 04 Sqmm cable with 01 run of 4 Sqmm earth wire along with PVC conduit shall be measured as one RM

M&L for concealed Sub main wiring with Four single core PVC insulated unsheathed cable 1100 volts grade, 6 Sqmm size ( 4 run x 6 Sqmm) with multistranded copper conductor, FRLS-H cable drawn in but including through concealed conduit, including PVC conduit medium grade, heavy duty, ISI marked not less than 32 mm dia, in any type of wall, roof, etc, with all connected fittings , including PVC insulated unsheathed 6.0 Sqmm FRLS-H cable with multistranded copper conductor of green colour as contineous earth conductor cable connected to earth dolly and make good to match with the existing surfaces after completion all as specified. Note- (i) Cutting in chases and pointing in brick wall/Stone Wall or any type of surface for concealing the conduit shall be done by contractor without any extra cost. (ii) Making good of distrubed surfaces matching with existing finishes shall be done by contractor without any extra cost (iii) Four runs of 06 Sqmm cable with 01 run of 6 Sqmm earth wire along with PVC conduit shall be measured as one RM

S&F DB Box, in sheet metal enclosure VT DB TPN, MCCB DB TPN 4 way, double door with MCCB as incomer (Suitable for mounting 160 Amp MCCB) and suitable for SP/TP DB in outgoing, enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43, IK 09, As Per IEC 61439-3, with 250 Amp fully insulated copper bus bar for each phase, with 2 Neutralbar, 2 Earth bar and cable ties for cable management, with fully insulated busbar and shrouded neutral bar, reversible door provision, with colour coded interconnecting wire set, , reversible door provision, blanking plates and circuit identification labels, including flushing and fixing DB box neatly in wall / solid block wall including copper lugs/thimbles duly crimped for connection complete all as specified and directed. Make- Legrand Cat Part No. 507745 Model: (Ekinox-3) or equivalent in Seimens/ Schinder/ L&T Note : (i) MCCB and DB box shall be of same make. (ii) MCCB shall be measured & paid seperately

S&F MCCB with Thermal - magnetic release of 125-160 Amps, 3 Pole, 415V, 25 kA, Ics=100%Icu with adjustable over load setting and adjustable short circuit setting as per IS-13947 & IEC 60947-2 including all accessories like spreader terminals and Phase barriers including making all electrical connections by providing lugs of suitable size complete all as specified and directed. Note: (i) MCCB and DB box shall be of same make.

S&F DB Box, in sheet metal enclosure MCB DB 04 way TPN Double door, factory made suitable for MCB as incomer and suitable for SP/TP DB in outgoing, enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43, IK 09, As Per IEC 61439-3, 415 volts, including blanking plate etc. DB box to be flush and fixed in concealed in wall complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and circuits complete as reqd at site as directed by the Engr-in-Charge.

S & F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 amps rated busbar, 8 way Double door enclosure made up of CRCA sheet steel, powder coated, IP 43 including fixing the DB box flush in wall of any type and making good the distrubed surface to match as the existing with all as specified and directed by Engr-in-charge

S & F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 amps rated busbar, 4 way Double door enclosure made up of CRCA sheet steel, RAL powder coated, IP 43 including fixing the DB box flush in wall of any type and making good the distrubed surface to match as the existing with all as specified and directed by Engr-in-charge

S&F MCB TPN 100 Amps, 415V, 16 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper /aluminium cable lugs with suitable size for incoming and outgoing all as specified and directed.

S&F MCB SPN 40 Amps 240V, 10 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper /aluminium cable lugs with suitable size for incoming and outgoing all as specified and directed..

S&F MCB SP 6 to 32 Amps 240V, 10 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper /aluminium cable lugs with suitable size for incoming and outgoing all as specified and directed. (NOTE for Ser. Item No. 269 to 276 above: All MCCB / MCBs and DBs shall of same make as directed by GE / Engr-in-Charge.)

Supply, installation and testing of Chemical Earthing complete with copper rod electrode of 17.2 mm dia, 3 mtr length with top copper terminal of size 100 x 50 x 5 mm placed under the ground below GL after drilling bore of 100 mm dia up to 3.5 mtrs depth in any type of soil / disintergated rock/ rocky strata any type and filling of BFC Compound having very high eletrical conductivity, moisture retaining capacity, hygroscopic, non-corrosive in nature and ROHS compliant, in slurry form all round the electrode in bore hole up to the top level. The earth pit shall be covered by providing Reinforced FRP square earth pit cover of size 300 x 300 x 240 mm and capable of carrying weight of 5 tons including making all connections with earth continuity conductor strip by providing brass nut bolted up to the test point complete all as specified directed including testing on completion of earthing.

Note for Ser. Item No. 277 above : (i) GI earth strip of size 32 x 6 mm up to 7.5 mtr length included in unit rate. (ii) GI strip will be laid below 20 cm from ground level and connecting the test point through plinth protection using HDPE pipe for protection, necessary cost of repair to plinth protection and brazing and welding/ providing brass nut bolt deemed to be included in the item. (iii) Contarctor shall submit the test report of earthing after satisfactorily completion. (iv) Contractor shall submit the complete literature and specifcation of earthing and shall take approval of GE before procurement of material and execution of job.

Material and labour for GI earth strip 32X6 mm as main earth lead on insulator or buried in ground/Wall/ ceiling etc, complete all as specified and directed.(Earth strip beyond 7.50 m in earthing shall be measured under this item)

M&L for laying 40 mm bore GI pipe, light grade, ISI marked, conf to relevant IS with all fittings, in crossing road/path and in pole/wall up to junction box including necessary clamping etc. complete all as specified and as directed by Engineer-in-Charge.

NOTES FOR ALL ITEMS OF BOQ : (a) The subject work lies in Restricted Area. (b) The Bidders are advised to visit the site of existing 'E' Sqn Bldg with prior appointment of GE to ascertain the conditions of working at site and also visit the sample block i.e. existing 'E' Sqn Bldg. The contractor shall deemed to have satisfied himself with nature of works, local facilities including type and nature of approach available to various locations of works and different mode of coveyance of materials, T&P etc. which is required to be involved in the subject tender and all matters affecting the execution and entire completion of work. The rates quoted shall be deemed to include considering all these site conditions to achieve workmanship similar to the sample block. No extra charges due to misunderstanding or otherwise shall be entertained. The contractor has to submit / upload on the Firm's letter head undertaking duly signed to the effect that he has visited the site and understood the complete scope of work alongwith / while uploading Cover-I details. No Claim of what-so-ever nature will be entertained on this account in future.

Horizon Construction (BID ID -3112208)

SHREE KRISHNA INFRASTRUCTURE (BID ID -3107288)

Deccan Enterprises (BID ID -3112964)

agarwal and company (BID ID -3113269)

KSP ENTERPRISES (BID ID -3109832)

Mukund Engineers and Contractors (BID ID -3112703)

SHAILENDRA B TULSANI (BID ID -3113969)

M/s L. K. Agarwal (BID ID -3112013)

M/S CHANDAN BUILDERS (BID ID -3113588)

S G Enterprises (BID ID -3112728)

K R TRADERS (BID ID -3113793)