Special repair to bldg No P-20 (Sick animal stable and dana room) of Vet hospital at Haft Chinar under GE 970 EWS

Amount

Taking down cement plaster of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L rendering 15 mm thick cement plaster in CM 1:4 on concrete or fair faces of brick surfaces finished even and smooth with out using extra cement on wall complete all as specified.

M&L rendering 15 mm thick cement plaster on fair faces of bricks or concrete surface in CM 1:6 finished even and smooth with out using extra cement on wall complete all as specified.

M&L for preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement based paint over a coat of alkali resisitant primer complete all as specified

M&L for preparation of new surfaces of steel of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as specified.

M & L for 15mm bore 'Medium grade' GI tubing with all fitting and fixed complete to walls and ceilings or laid in floors including taking down existing tubing complete all as specified and as directed.

S&F in repairs of ISI marked fancy type Pillar Tap of 15mm bore dia, chromium plated, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

S&F for stainless steel sink with draining board made of stainless steel 1 mm thick sheet for kitchen with waste coupling, waste pipe, washer and including all necessary items including fixing to brackets and connected union to pipe complete of overall size 915x460 mm with bowl size 410mm x 330mm x 160mm complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for Non skid ceramic coloured tiles not less than 8 mm thick (square/ rectangular) area of each tiles exc 0.11 but not exc 0.18 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or colour cement to match laid over and including 15mm cement screed bed in CM (1:4) complete all as specified.

M&L for 25mm thick cement concrete 1:2:4 type B-1, (using 20mm graded crushed stone aggregate) as in flooring or sub base including demolition of PCC floor of any description complete all as specified and directed.

M&L for glazed coloured ceramic tiles in vertical surfaces such as skirting /dados and riser to steps of size 450x300x7mm thick set and jointed and pointing in white or coloured cement to match over 10 mm thick cement plaster in CM 1:4 complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sq. m but not exc 4 sq. m each complete all as specified and as directed.

M&L for providing cement concrete 1:2:4 Type B0 (using 12.5mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth, string, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

M & L for sheet glass 4.0mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sq m in each pane complete all as specified and as directed.

S & F for galvanized mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified and as directed.

M&L for water tanks, exe 250 & not exe 500 Litres capacity, open or closed, hoisted and fixed in position complete all as specified and as directed.

M&L for 500 Litres capacity tripple layered rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and as directed.

S&F in repair for ISI Marked 20mm dia Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and as directed.

Dismantling Wall and ceiling boards (fibre pulp, insulation, etc.) or insulation boards/slabs /blankets, any thickness, including cover fillets complete all as specified.

S&F 605mm x 605mm anodised aluminium snap grid frame work for false ceiling complete all as specified and as directed.

S&F for Hangers 6mm dia GI (upto 1200mm length ) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fastener 12.5mm dia 40mm long complete all as specified

M&L for providing and fixing 12mm thick gypsum board in ceiling fixed with screws as per manufacturer's instructions complete all as specified and as directed.

M&L for brickwork with sub-class 'B' bricks, straight or curved on plan exc 6m mean radius built in CM 1:4 including demolition of brickwork complete all as specified and as directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position (Framed work) complete all as specified and as directed.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed.

S&F for pre-painted galvalume aluminium zinc coating GI based corrugated steel 0.50mm thick of any colour having tense strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified.

S&F for pre-painted galvalume aluminium zinc coating GI based Plain steel 0.50mm thick of any colour having tense strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for as in mangers complete all as specified and as directed.

Demolition of Cement concrete (unreinforced) of any description in ground floors and pavings n exe 15cm thickness (below or above ground level) complete all as specified and as directed.

M&L 75 mm thick PCC (1:3:6) C-1 (using 20mm graded crushed stone aggregate) as in path/plinth protection finished even & smooth without using extra cement laid in bays including joint filling using sealing compound grade 'A' complete all as specified.

M&L for 75mm thick cement concrete 1:4:8 type D-2, (using 40mm graded crushed stone aggregate) as in sub base, flooring complete all as specified and as directed.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed.

Taking down roof trusses, coupled rafters or trussed beams including taking down trusses etc for renewal of any defective members and reassembling and refixing the truss after raising the height (timber renewed to be measured separately), clear span above 8 metres & upto 12 metres complete all as specified and as directed.

S&F rolled mild steel work in roof trusses (framed), trusses, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., quality confirming to GDE Fe 410-W complete all as specified and directed.

S&F rolled mild steel in plates channels (plain or chequered), square cut or notched (ordinary and counter sunk) forming holes, without any attachment, of quality GDE Fe 410-W complete all as specified and directed.

Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of GE.

Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of GE.

M&L for ACP board for fixing in aluminium partition and doors complete all as specified and as directed.

M&L for 30mm thick stable interlocking rubber matting/flooring suitable for horses, mules etc complete all as specified and as directed.

M&L for PCC 1:2:4 type B2 (using 40mm graded crushed stone aggregate) as in surface channels and drains complete all as specified and directed.

M&L for galvanised steel mangers for feeding and drinking water, size of bowl not less than inner width 0.45m and depth 0.30m, for horses/mules etc complete all as specified and directed.

Taking down old and unserviceable alumunium point wiring in batten/ conduit and making good the disturbed surface to match the existing surface, complete all as specified

Taking down old and unserviceable submain wiring any size of two core including earth wire complete including batten/ conduit and make good the disturbed surface to match the existing surface complete all as directed

Taking down old and unserviceable, distribution board any type including/ sheet metal enclosures, after removing all connection and make good the disturbed surface all as directed.

Material & Labour for point wiring for one light / Fan point controlled by one, one way switch complete with 1.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed, fire retardant low smoke cable 1100 volts grade ISI marked drawn through and including PVC casing & caping on surface of wall, not less than 25mm width confirming to IS 9537 (Part-III) 1983, including all accessories like bend, tees, junction boxes etc., 1.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed, fire retardant low smoke cable as a earth wire connected to common earth dolly, etc and including sunken type pressed steel terminal box with 1.8 mm wall thickness, of suitable size for flush type switch with cover plate, cost of cable provided from sub main DB to respective switch board in rooms shall be included in the quoted point wiring rate complete. NOTE - Colour code of cable Phase-Red Neutral- Black and Earth -Green)

All as item No 48 above but for one 3 pin socket outlet, 5/6 Amp socket outlet on same board with other switches.

All as per item No 48 above but for one 3 pin socket outlet, 5/6 Amp socket outlet on independent board.

All as per item No 48 above but wiring with cable 2.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed fire retardant low smoke, cable as earth wire connected to common earth dolly for 15 Amps multipurpose socket outlet on independent board, controlled with one way switch.

Supply and fixing socket outlet 2 in 1, 3 pin, 5 amp flush type ISI marked for the same board complete all as specified and directed.

Supply and fixing switch socket combination 5 Amps 2 in 1 flush type multipurposes for independent board complete all as specified and directed.

Supply and fixing switch piano, flush type single pole, one way 5 Amps 3 pin, ISI marked for the same board complete all as specified and directed.

Supply and fixing socket outlet 3 pin, 15 Amp, flush type , ISI marked complete all as specified and directed.

Supply and fixing switch piano 15 Amp, flush type single pole, ISI marked 16 Amps One Way switch omplete all as specified and directed.

Supply and fixing ceiling rose, 3 phase/PVC/polycarbonate, isolated body type complete all as specified and directed.

Supply and fixing in repairs of tube light fitting 1x 22 watts 4 feet with LED batten with aluminium housing and integrated electronic driver in cluding LED tube light white colour complete including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. Make: Havells Catpart No.ENDURALINEARNEOBS22WLED865SPCWH or equivalent in Bajaj/ Crompton/Philips.

Supply and fixing in repairs of tube light fitting 1x 10 watts, 2 feet with LED batten with aluminium housing and integrated electronic driver including LED tube light white colour complete including connecting up with twin core twisted flexible copper conductor cable with suitable size all as specified

S&F for Sub Main wiring using FRLS-H Insulated unsheathed, multistrand copper conductor FRLS-H PVC cable 2 runs of size 4 sqmm for phase and neutral and one run of 4 Sq mm for earthing. drawn through PVC casing caping of suitable size fixed on wall/ground/Ceiling etc., and complete all as specified. NOTE: Phase should be Red / Yellow / Blue, neutral should be black and earthing wire should be green in colour. Two runs of cable for phase / neutral and one run of cable for earth including casing and caping will be measured and paid as one unit length.

S&F for Sub Main wiring using FRLS-H Insulated unsheathed, multistrand copper conductor FRLS-H PVC cable 2 runs of size 6 sqmm for phase and neutral and one run of 6 Sq mm for earthing. drawn throughthrough PVC casing caping of suitable size fixed on wall/ground/Ceiling etc., and complete all as specified. NOTE: Phase should be Red / Yellow / Blue, neutral should be black and earthing wire should be green in colour. Two runs of cable for phase / neutral and one run of cable for earth including casing and caping will be measured and paid as one unit length.

S&F for Sub Main wiring using FRLS-H Insulated unsheathed, multistrand copper conductor FRLS-H PVC cable 2 runs of size 10 sqmm for phase and neutral and one run of 10 Sq mm for earthing. drawn through through PVC casing caping of suitable size fixed on wall/ground/Ceiling etc., and complete all as specified. NOTE: Phase should be Red / Yellow / Blue, neutral should be black and earthing wire should be green in colour. Two runs of cable for phase / neutral and one run of cable for earth including casing and caping will be measured and paid as one unit length.

Supply and fixing in repairs round shape slim fit down light LED 15 Watt round recess (Warm/ Warm White) 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size completecomplete all as specified and directed. Make: Havells Catpart No.EDGEPRORDDLR15WLED840S or equivalent in Bajaj/ Crompton/philips.

Supply and fixing sheet metal enclosure double door for DBs TPN-4 Way 415 Volt with 200 Amp rated bus bar complete all as specified and directed.

S&F DB with sheet metal enclosure 240 volts, 8 way with 200 Amp rated bus bar single pole & neutral double door type for MCBs including mounting work as required in position .complete all as specified and as directed.

S&F DB with sheet metal enclosure 240 volts, 12 way with 200 Amp rated bus bar single pole & neutral double door type for MCBs including mounting work as required in position .complete all as specified and as directed.

Supply and fixing in repairs Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp, 240 Volts complete all as specified and directed.

Supply and fixing in repairs 415V 10KA 'B' curve miniature circuit breaker (MCB) TPN and current carrying capacity 63 Amp in the DB complete with connection, testing and commissioning complete all as specified.

Supply and fixing in repairs rating 240V, 10KA 'B'curve miniature circuit breaker (MCB) SP and current carrying capacity 40 Amps in the MCB DB complete with connection testing and commissioning complete all as specified.

Supply and fixing in repairs rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) SP and current carrying capacity 5-32 Amps in the MCB DB complete with connection testing and commissioning complete all as specified.

S&F in repairs Lamp holder, PVC /Polycarbonate type with back plate suitable for batten fitting of LED lamp 9 watt complete all as specified and directed.

S&F in repairs LED light fitting 1x9W/1X10W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified.

Supply and fixing exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm including electric connection from ceiling rose to connector with flexible cord twin core twisted copper of size 23/0.0076 complete all as specified and directed.

Supply and fixing wall mounted air circulator fans complete with blades, electronic regulator and accessories, 230 V, 600 mm sweep. Min air delivery 125 CMM including electric connection from ceiling rose to connector with flexible cord twin core twisted copper of size 23/0.0076 complete all as specified.

Supply and fixing ceiling fan complete with blades, down rods and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fixing stepped type electronic fan regulator (should be suitable for ceiling fan in schedule item no.75 on the existing phenolic laminated sheet etc. as reqd at site complete all as per specified and directed.

Renewal of Earthing complete with galvanized street earth plate electrode 600x600x6mm thick buried directly in ground (earth plate not less than 2.25mtr deep below normal ground level) with top edge of the plate not less then 1.50 mtr. below the normal ground level connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washer of galvanized iron or steel all as shown in electrical plate No 5 connected to earthing test point all as specified and testing on completion including the material and labour for :- (a) Excavation and earth work or drilling hole for electrode in any type of soil (b) PCC pit in cement concrete 1:2:4 type B-1 (c) CI cover with suitable handle (d) Funnel with watering pipe of GI 20mm nominal bore medium grade and Aluminum lugs etc all as specified. (e) 15mm nominal bore medium grade GI protection pipe up to 7.50 meter long for protection of earthing lead. (f) Requisite quantity of charcoal and common salt (g) Connection to earthing test point and testing on completion.

Supply and Laying of PPR pipes 3- layer SDR 7.4 of outer diameter of pipes as following UV stabilized and antimicrobial fusion welded having thermal stability for hot and cold water supply all PPR plain & brass threaded polypropylene random fittings laid in trenches including fittings and testing complete all as specified and directed for following sizes :-

(a) 25 mm dia.

(b) 32 mm dia.

Making connection of PPR 32 mm dia distribution branch with PPR main of sizes 50 mm to 75 mm by providing and fixing tee including cutting and making fusion joint etc complete all as specified and directed.

Supply and fixing PPR gate valve (brass insert) of size 25 mm dia including connection and testing complete all as directed.

Supply and fixing PPR gate valve (brass insert) of size 32 mm dia including connection and testing complete all as directed.

S&F GI Flat strip clamps of size 25mm x 3mm duly bended as per the size of GI tubing and site condition,drilled all as specified.

Supply, installation, testing and commissioning of standalone air heating system for space heating of hot air capacity of 25000 Kcal/Hr suitable for indoor operation with heat exchanger diesel or kerosene and fuel filter, burner, blower fan, automatic digital temeparture controller, control panel with visual controls, safety interlocks, over load relay, timers, suitable capacity of fuel tank with following features:- (a) Bottom Flow (Hot Air release from bottom side of machine) (b) Control panels are double insulated (c) Burning chamber is made of flame resistant mild steel (d) Fully automatic operation (e) electronic control board is not effected high temperature (f) The monoblock body is insulated by the fiberglass and the exterior protection is secured against corrosin by powder painted sheet metal (g) Heat converting pipes are made of finest quality mild steel (h) Environmental friendly (j) Self diagnosis (k) Auto restart (k) Lock (l) Instant Heat (m) Exterme temperature controlling capabilities at minus at 50˚C with its improved heating capacity it heat easily at sub zero temperature. (n) Stablizer free operation (o) Heat output - 25000 Kcal/Hr (p) Hot Air Tempertaure :40˚C (q) Temperature rise :90˚C max (r) Thermal efficiency :80-90% (s) Electric Supply :220Volt, 50 Hz (t) Temperature control : Automatic (u) Fuel type : Diesel / kerosene (v) Burner : Riello/Ben-ton. Make: Supertherm/ Westherm/Thermax/ Top mind Industries.

Supply installation testing and commissioning of solar water heating system with ETC (Evacuated Tube collector) TECHNOLOGY with suitable KW electrical back up as per manufacturer specification suitable for single phase 220 V AC supply complete with ETC type collector, Hot water tank,tank stands etc as per the following specifications. (A) COLLECTOR: Collector 500 LPD ETC type with as per OEM recommended of vertical evacuated tubes, duly installed on angle iron frame, transmittance of cover glass tubes 85%, reflectance of glass tubes more than 85%, absorbance of glass tubes 92%, type of coating (Cu/AI/SS) and reflectance of coating as recommended by manufacturer having wind resistance up to 100 Km with freezing resistance minus 20 deg C and heating up coefficient 240 deg C having average thermal efficiency 58.76% and maximum rise in temp 53.04 deg C (in 24 hours) without night losses fixed at angle of inclination from horizontal as per recommendation of manufacturer. (B) HOT WATER TANK: Hot water tank as per OEM recommended ltr capacity with suitable KW electrical back up made out of stainless steel sheet not less than 0.5 mm thick duly insulated with puff insulation 50 mm thick having density not less than 36 kg having thermal conductivity 0.29 m/k duly covered with PPGI cladding fixed with temperature gauge, inlet and outlet valves of suitable size duly installed on staging fabricated out of MS angle of appropriate size as recommended by manufacturer duly fixed properly and painted with two coats of anti corrosive paint over a coat of red oxide primer. NOTE: (i) 5 Nos of spare ETC glass tubes with each system are to be supplied by the contractor with in over all cost quoted. (ii) MS staging and puff insulated water storage tank for cold water, Hot and cold water pipes including valves (to and from system), insulation to pipe and valves to be measured and paid separately. (iii) Any other item required for successfully operation of system is deemed to be included in overall cost quoted. (iv) Make of system: INTER SOLAR/SUN MAGIC/BIPIN INDUSTRIES/TATA BP SOLAR/BORO SOLAR/VENUS (v) System shall be installed and comissioned by authorised rep of firm supplying the solar water Heating system.

Supply and fixing 3-layer PP-R (Polypropylene random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc of size 25mm bore with nitrile rubber insulation complete all as directed. Make : SFMC/SAFE/PRINCE

All as per item No.85 but size of 20 mm bore with nitrile rubber insulation complete ll as specifoed and directed.

M&L for lagging to pipes used in external water supply with 50mm thick bounded mineral wool performed "SNAP ON' pipe section of density 144 Kg/cum confirming IS-9842 with chicken wire mesh wire netting 25mm gause, 20 mm mesh with .01mm aluminium foil cladding to 25mm dia pipe complete all as specified.

M&L for lagging to pipes used in external water supply with 50mm thick bounded mineral wool performed "SNAP ON' pipe section of density 144 Kg/cum confirming o IS-9842 with chicked wire mesh wire netting 25mm gause, 20 mm mesh with .01mm aluminium foil cladding to 20mm dia pipe complete all as specified.

Supply and fixing PPR gate valve as per IS-15801 (brass insert) of size 20 mm dia including connection and testing complete all as directed.

M&L for 500 ltr capacity rotational moulded grade polyethylene (PE) water storage tank which duly stablized with anti-oxidants and compounds and, provides protection heat and oxidation and Cylindrical, vertical with closed top with double layer conforming to IS-12701-96 complete including provision of all inlet,outlet,overflow and drain pipe fitting and suitable puff insulated of complete tank all as specified and directed.

S&F for iron pipe including GI fittings of the length and size as per site requirement all as directed.

M&L for structural works for staging of cold/hot water tank with MS flat iron of size upto 75mm framework of water tanks and similar work con-forming to Fe. 290 Gde-E-165 complete all as specified.

Supply and installation monoblock self priming pump set capacity of 1 HP (0.75 KW) with suitable starter and cable complete all as specified and directed.

NOTE :- An amount of Rs. 76,682.00 on account of Credit Schedule for Schedule 'A' Part-II shall be deducted from total quoted amount of BOQ to arrive at the contract sum.

M/S RAFIQ AHMAD SOFI AND SONS (BID ID -3236932)

M/S Sultan Enterprises (BID ID -3242466)

rafiq trading co (BID ID -3242698)