Improvement and Renovation of Le Cafe Building, Beach Road, Puducherry

Amount

Earthwork in excacavation over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth lead upto 50m and lift upto 1.5m - disposed earth to be and lift upto 1.5m - disposed earth to be levelled and neatly dresses - all kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50m and lift upto 1.5m

Supplying chemical emulsion in sealed containers including delivery as specified- Chlorpyriphos / lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST - CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) - tratment of soil under existing flooors using chemical emulsion @ one litre per hole, 300mm apart including drilling 12mm diametre holes and plugging with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor - with Chlorpyriphos / lindane E.C. 20% with 1% concentration -

Diluting and injecting chemical emulsion for POST - CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) - Treatment of existing masonry using chemical emulsion @ one litre per hole at 300mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 ( 1 cement : 2 coarse sand) to the full depth of the hole - with chlorpyriphos / lindane E.C. 20% with 1% concentration

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering shuttering, finishing and reinforcement All work upto plinth level 1:1.5:3 (1cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness) , including attached pilasters, buttresses , plinth and sting courses, fillets, columns, pillars, piers , abutments , posts and struts etc. upto floor five level excluding cost of centering , shuttering, finishing and reinforcement - 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size)

Centering and shuttering including strutting , propping etc and removal of form for - Walls (any thickness ) including attached pilasters, butteresses plinth and string courses etc.

Centering and shuttering including strutting , propping etc and removal of form for - Suspended floors, roofs, landings, balconies and access platform

Steel reinforcement for R.C.C.work including straightening , cutting , bending, placing in position and binding all complete upto plinth level - Thermo-Mechanically treated bars (TISCON / VIZAG/ IISCO / SAIL / JSW) Fe - 415 or more

Steel reinforcement for R.C.C.work including straightening, cutting , bending, placing in position and binding all complete above plinth level - Thermo - Mechanically Treated bars (TISCON / VIZAG /IISCO / SAIL / JSW) Fe - 415 or more

Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 3.5 in foundation and plinth in - cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S (non modular ) bricks of class designation 3.5 in superstructure above plinth level upto floor five level in all shapes and sizes in - cement mortar 1:6 ( 1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 in superstructure above plinth level upto floor V level - cement mortar 1:4 (1 cement : 4 coarse sand)

Extra for providing and placing in position 2 nos. 6mm dia MS bars at every third course of half brick masonry (with FPS bricks).

Providing and fixing 18mm thick gang saw cut, mirror polished (premoulded and prepolished) machine cut for kitchen platforms,vanity counters, window sills,facias and similar locations, of required size, approved shade,colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing,curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels - Granite of any colour and shade - Area of slab upto 0.50 sqm

Providing and fixing stone slab with table rubbed , edges rounded and polished, of size 75x50 cm deep and 1.8cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6mm nominal size) and finished smooth - White agaria mable stone

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) -Vengai wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows, and clerestory windows, including ISI marked M.S.pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately , all complete - Vengai wood - 30 mm thick shutters

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors , windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick - Vengai wood

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors , windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick - Float glass panes - 4mm thick glass pane

Extar for providing frosted glass panes 4mm thick instead of ordinary float glass panes 4mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured)

Providing and fixing specified wood frame work consisting of battens 50x25 mm fixed with rawl plug and drilling necessary holes for rawl plug etc. including priming coat complete - Kiln seasoned and chemically treated Padak wood

Providing 40 x 5 mm SS hold fast 40 cm long including fixing to frame with 10 mm diameter bots, nuts and wooden plugs and embeddings in cement concrete block 30 x10 x 15 cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)

Providing beams including hoisting, fixing in position and applying wood preservative for the unexposed surfaces etc . Complete with - Vengai wood

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 125x75x4mm

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete - 100 X 75 X 4 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc.complete : - 300x10mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc. complete : - 200x10mm

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc. complete :-125mm

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc.complete - Twin rubber stopper

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance +_1mm ), with wall thickness 2.0 mm (+-0.2mm) , corners of the door frame to be jointed with galvanized brackets and stainless steel screws , joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S.tube of size 19 x 19 mm and 1mm (+-0.1mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification - Extruded section profile size 42 x 50 mm

Providing and fixing to existing door frames - 30 mm thick factory made Polyvinyl Chloride (PVC) door shutters made of styles and rails of a uPVC hollow section of size 60 x 30 mm and wall thickness 2 mm (+- 0.2 mm) with inbuilt decorative moulding edging on one side The styles and rails mitred and joint at the corners by means of M.S. galvanised / plastic brackets of size 75 x 220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S.tube of size 25x20mm and 1mm (+- 0.1mm) wall thickness . The lock rail made up of 'H' section , a uPVC hollow section of size 100 x 30 mm and 2 mm (+-0.2 mm) wall thickness , fixed to the shutter styles by means of plastic / galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm (+_ 0.1mm) wall thickness . They panels filled vertcally and tie bar at two places by inserting horizontally 6 mm galvanised M.S.rod and fastened with nuts and washers , complete as per manufacturer's specification

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) , of approved make (Jhonson / Asian / Somany / Nitco) in all colours , shades of size 300 x 450 mm as approved in skirting , risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement with pigment of matching shade complete - size 300x450 mm

Providing and laying rectified ceramic rustic / matt finish floor tiles 300 x 300 mm or more ( thickness to be specified by the manufacturer ) of 1st quality conforming to IS:15622 of approved make ( Somany / Nitco) in all colours shades laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigments etc., complete

Providing and fixing PVC corner beading of required size to suit the thickness of the wall tile at the corner joints of dado works

Providing and laying pressed clay tiles (as per approved pattern 18mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound, laid over a bed of 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete

Lime concrete terracing on roofs of required thickness laid to fall with 25mm nominal size brick aggregate and 50% lime mortar 1:2 (1 lime putty : 2 surkhi) rammed and finished with gur and belgiri treatment complete including rounding of junctions with Parapet wall complete

Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion, (i) Single socketed pipes - 110 mm diameter.

Providing and fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - Single tee without door -110x110x110mm

Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - shoe (plain) - 110mm shoe

Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised- PVC rain water pipes by means of 50x50x50mm hard wood plugs screwed with M.S. screws of required length, including cutting brickwork and fixing in cement mortar 1:4 ( 1 cement :4 coarse sand) and making good the wall etc., complete - 110mm

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm Primer as per manufacturers specifications

Painting wood work with deluxe multi surface paint of required shade. Two or more coat applied @0.90 ltr / 10sqm over an under coat of primer applied @ 0.75 ltr / 10 sqm of approved brand and manufacure

Finishing with epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete - on steel work

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing R.C.C work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge - In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc.complete and stacking within 50 metres lead - of area 3 sqm and below

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead - for thickness of tiles 10mm to 25mm

Dismantling tiled roofing with battens, boarding etc. complete including stacking of serviceable material and disposal of unserviceable material within 50 metres

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Supplying fixing and commisioning of Suguna/ Texmo/Sharp 2 HP mono- block pumpset slow speed single phase motor. The rate include the cost of pumpset, pumpset fixing in position and test run etc.complete

Providing and fixing water closet squatting pan (Indian type W.C.pan) with 100 mm Sand Cast Iron P or S trap, 10 litre low level white P.V.C flusing cistren, including flush pipe , manually controlled device (handle lever) conforming to IS : 7231 , with all fittings and fixtures complete , including cutting and making good the walls and floors wherever required. White vitreous china Orissa pattern W.C.pan of size 580x440mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type W.C.pan) with seat and lid, 10 litre low level white P.V.C. flusing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS: 7231,with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required - W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32mm C.P.brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required - white Vitreous China wash basin size 550x400 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing Stainless steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I.brackets and stainless steel plug 40mm , including painting of fittings and brackets, cutting and making good the walls wherever required - kitchen sink without drain board - 610x510 mm bowl depth 200mm

Providing and fixing white vitreous china water closet squatting pan (Indian type) : Orissa pattern W.C. pan of size 580x440 mm

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x 260 x350 mm or 340x410x265 mm sizes respectively.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing - rectangular shape 453 x 357 mm

Providing and fixing PTMT waste coupling for wash basin and sink, of approved quality and colour - waste coupling 31 mm dia of 79 mm length and 62 mm breadth weighing not less than 45 gms

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour - 600 mm long towel rail with total length of645 mm, 78 mm wide and effective height of 88mm, weighing not less than 190 gms

Providing and fixing CP brass health faucet of approved quality - 15 mm nominal bore

Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall) - 20mm nominal outer dia pipes

Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall) - 25mm nominal outer dia pipes

Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Interna work exposed on wall) - 32 mm nominal outer dia pipes

Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall) - 25mm nominal outer dia pipes

Providing and fixing brass stop cock of approved quality - 20mm nominal bore

Providing and fixing gun metal gate valve with CI wheel of approved quality (screwed end) - 25 mm nominal bore.

Providing and fixing ball valve (brass) of approved quality , high or low pressure, with plastic floats complete - 20mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS :12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Providing and fixing PTMT grating of approved quality and colour - rectangular type with openable cirucular lid - 150mm nominal size square 100mm diametre of the inner hinged round grating

Cutting holes upto 30x30 cm in walls including making good the same - with common burnt clay F.P.S.(non - modular) brick

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality - LD - 2.5 -rectangular shape 600x450 mm inernal dimensions

Providing and fixing on wall / column face unplasticed - PVC soil and waste pipes (type - B) conforming to IS : 13592- 1992 including jointing with seal ring conformation to IS : 5382 leaving 10mm gap for thermal expansion - single socked pipes -110mm diametre

Providing and fixing on wall face / column face unplasticised - PVC mould fittings /accessories for unplasticisd - PVC soil and waste pipes conforming to IS : 14735 - 1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Single tee without door - 110 x110x110mm

Providing and fixing on wall face / column face unplasticised - PVC mould fittings /accessories for unplasticisd - PVC soil and waste pipes conforming to IS : 14735 - 1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - bend 110 mm

Providing and fixing on wall face / column face unplasticised - PVC mould fittings/ accessories for unplasticisd - PVC soil and waste pipes conforming to IS : 14735 - 1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - bend with door 110 mm

Providing and fixing on wall / column face unplasticised - PVC soil and waste pipes (type B) conforming to IS :13592 - 1992 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Single socketed pipes 75mm diameter

Providing and fixing on wall / column face unplasticisd - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS :14735 -1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Single tee with door - 75x75x75mm

Providing and fixing on wall / column face unplasticisd - PVC moulded fittings/ accessories for unplasticisd - PVC soil and waste pipes conforming to IS :14735 -1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Single tee without door - 75x75x75mm

Providing and fixing on wall / column face unplasticisd - PVC moulded fittings/ accessories for unplasticisd - PVC soil and waste pipes conforming to IS :14735 -1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Bend 75 mm

Chipping of unsound / weak concrete material from slabs, beams, columns etc. with manual Chisel and / or by standard power driven percussion type or of approved make including tapering of all edges , making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete - 25 mm average thickness

Providing , mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and complete in all respect - SBR Polymer ( @ 10% of cement weight ) modified cementitious bond coat @ 2.2 kg cement per sqm of surface area mixed with specified proportion of approved polymer

Supply of Quarry rubbish including stacking to department gauge for premeasurement and spreading required thickness

Providing two legged scaffolding using 15 cm diameter blue - gum posts or casurina posts or best quality bamboo - posts of 4m over all length (3.0m height + 0.5 m projection + 0.5 into the ground) the distance between the two rows being 1.25 m and the spacing of posts with 0.5 m overlap on either side and braces to step up and providing a platform with country wood planks of 40mm thick and 1m width etc in a complete form using coir and nails 1 m run (Rate of scaffolding for a height of 3 m and lenghth of 1 m)

Disposal of building rubbish and unserviceable dismantled materials upto 5Km radius the rate include incidental charges and loading for transportation by mechanical means. Rate approved by SE-I vide Lr.No. 183/ PW/SE-I/AE(P)-II/F.No.309/2018-19/91 dt. 22.01.2019

Providing and fixing PVC 110mm dia terminal guard - Vent Cowl etc., complete as directed by the Engineer-in-charge. Rate approved by SE-I vide Lr.No. 560/ PW/SE-I/ AE(P)-II/ F.No. 221/2014-15/ dt.13.01.2015

Supplying and fixing of Cast Iron compound wall fencing as per design and drawing, Each bay consists of four horizontal member each of 30 kg weight and horizontal rods of alternate small and big rods of 25mm dia (+ or – 2 mm thickness variation) and 10 nos of small rod and 9 nos of big rod and the centre rod will be drilled into the wall and each bay is supported by compound wall intermediate pillar. The rate includes material, labour for fixing and overhead charges, the work should be done as per direction of Engineer - in - charge-Appl. No.256 /PW /SEI/AE(P)-II/F.No.221/17-18/1268 dt.20-10-2017

12mm cement plaster of mix cement mortar 1:3(1 cement:3 fine sand)

Plastering the walls 25 to 30mm thick at all height using Composite design mix 1:2 in two coats under layer 15mm thick plaster and top layer 10 to 15mm thick plaster of the composite design mix as follows - (Cement (OPC) 1 part, silicafume 1 part, lime 6 part) Fine M. Sand 2 part and airent admixture 100 ml for 50 kg powder including necessary scaffolding, labour, materials, curing etc., complete work as per specifications as directed by Engineer-in-charge

Providing and fixing 15mm thick eaves board of 20 cm height in Padauk wood planks as per the detailed drawing. The rate to include the cost of all materials labour charges for hoisting, fixing the board in position to the wooden rafters drilling holes and fixing with screws to the alignment , scaffolding, applying wood preservatives, etc. complete. As directed by the Engineer in charge.

Providing and fixing 3 lined dressed granite brackets (45x15x10cm),sunk and moulded as per drawings,as support for thewooden beams.The rate are inclusive of materials ,labour,civil works , scaffolding , etc, complete as per Engineer-in-charge. APPROVED BY - No128/PW/SE-I/AE(P)-I/F.CB330/2015-16

Supplying and fixing of double groove approved mangalore ridge tiles, as per standard specification and including all scaffolding, labour and sundries complete work including tying of edge tiles with 18 gauge copper wire as per direction of Engineer in charge. Appd by 251/PW/SEI/AE(P)- II/F.No.221/2017-18/1253.dt.16/10/2017

Supplying and fixing of double groove approved mangalore tiles,as per standard specification rate to include tying of edge tiles with 18 gauge copper wire and brass screw as per direction of engineer in charge.(Appd by 251/PW/SEI/AE(P)-II/F.No.221/2017-18/1253.dt.16/10/2017

Providing and fixing 12mm thick Bison board (shingles) in place as per design and drawing.The rate to include painting with two coats approved paint with one base coat of a approved primer,and all material,labour etc.,complete-

Supplying of M.S square rod 40mm x 40mm in size for holding wooden wall plate as per detailed drawing rate to include the cost of scaffolding, cutting, bending placing and welding and fixing the wall in positionwith 1:1.5:3 Cement concrete and two coat of powder coat over a base approved primer -Large size.-Appd by 319/PW/SEI/AE(P)-II F.No.221/2017-18/1521 dt.14-12-17.

Providing and laying 45 x 45cm grey granite slab of thickness 3cm in the pavements top surface flame finished with neat edges, 1cm wide recessed cement pointing, laid over 2cm thick cement mortar 1:4(1 cement :4 sand)(Rate approved by SE-I vide No:244 /PW/SEI /AE(P)II /F.No. 221/2017-18/1226.)dt:09-10-17

Providing and fixing 3 line dressed granite base of 25x25x15cm size for the wooden pillar with tough seal at the base, complete work. The rate inclusive of materials, labour, transport etc., complete as per architectural drawing as directed by Engineer in charge.

Removing the loose particles /rust/mill scale deposited completely duly cleaning it with wire brushes / crush sheet etc., and removing the dust over the old concrete surface and providing and system based aromatic rust remover of CFRA/ SIKA/ FOSROC/Mc Bauchine / Don/ BASF OR EQUIVALENT make certified and tested by accredited instructions (confirming to IS 9077-1979 (reaffirmed - 1997) Appendix B, Clause 5.3.3) including all tools complete as per manufactures specification and as directed by the Engineer - in charge ( Rate approved Vide lr.No. 7677/PW/SEII/AE(P)-6/SB-150/2017-18/1152 dt. 06.02.2018)

Applying a polymer based anticorrosive coating material of CERA /SIKA/ FOSHOC/ Me Bauchrnie / DON / BASF OR EQUIVALENT make certified and tested by accredited institutions mixing mechanically until it is homogeneous and applying the same as one rich coat on prepared steel surface with brush with all lead and lift etc., complete and as directed by the Engineer-in -charge (Measurement as per the total area of treatment) ( Rate approved Vide lr.No. 7677/PW/SEII/AE(P)-6/SB-150/2017-18/1152 dt. 06.02.2018)

Sealing of cracks / porous concrete by Pressure grouting using cement slurry mixed with non shrink expanding grouting compound of CERA /SIKA / FOSROC / Mc Bauchmie / Don / BASF or equivalent make certified & tested by accredited institutions like IIT / SERC or so (confirming to BS 8110 Part 1), mixed in the ratio of 225g per 50 kgs bag of cement for injection grouting the RCC slab to strengthen the RCC slab ( Rate approved Vide lr.No. 7677/ PW/SEII /AE(P)-6/SB-150/2017-18/1152 dt. 06.02.2018)

Providing high strength Non shrink free flow micro concrete of / CERA / SIKAI / FOSROC / Mc Bauchmie / DON / BASF OR EQUIVALENT make certified and tested by accredited institutions like llT / SERC / NTH or so (confirming to ASTM C109 7cm cube for compressive strength 45-50 MPa, Physical properties : Tensile Strength- 2.0 N/Sqm @ 28 days (BS 4551-80), Flexural Strength - 5.0 N/Sqm @ 28 days) over the Epoxy bonding agent applied area on columns, slabs, beams etc., upto floor five level (aggregates of 6mm to 12mm chips may be added) (Measurement has to be taken considering 15mm thickness of repaired surface). For this treatment precise quantity of water ie 0 .15 W/P ratio will be maintained for good mortar consistency as per the manufacturers specification with all lead and lift etc., complete and as directed by the engineer in-charge including cement plaster. ( Rate approved Vide lr.No. 7677/PW/SEII/AE(P)-6/SB-150/2017-18/1152 dt. 06.02.2018)

Providing high strength Non shrink free flow micro concrete of ERA/ SIKA/ FOSROC/Mc Bauchimie/DON/BASF OR EQUIVALENT Make certified and tested by accredited institutions like IIT/SERC/NTH or so (confirming to ASTM C109. 7cm cube for compressive strength 45-50 MPa, Physical properties : Tensile strength - 2.0 N/Sqm @ 28 days (BS 4551-80), Flexural strength - 5.0N/Sqm @ 28 days) over the epoxy bonding agent applied area on columns, slabs, beams etc., upto floor five level (aggregates of 6mm to 12mm chips may be added) (Measuring has to be taken considering 60mm average thickness of prepared surface) for this treatment precise quantity of water ie 0.15 W/P ratio will be maintained for good mortar consistency as per the manufactures specification with all lead lead and lift etc., complete and as directed by the Engineer - in charge (Note: shuttering and reinforcement wherever shale be paid seperately ( Rate approved Vide lr.No. 7677/PW/SEII/AE(P)-6/SB-150/2017-18/1152 dt. 06.02.2018)

Providing shear connectiors of 8mm to 12mm dia rods 100mm deep drilled at necessary places in concrete surface including drilling, cleaning the drilled holes with air blower to remove all dust and fixing the shear connectors in the filled holes with a thixtropic polyester grout KEYGROUT at 0.022 kg/hole mix 1:2 (1 resin : 2 powder) as per the specification of M/s.Dan construction chemicals India Ltd., including all lead and lift etc.,complete and as directed by the Engineer-in-charge. The rate is excluding steel reinforcement. upto 10mm dia rod

M/s. Murali and Bros

Savani Heritage Conservation Private Limited