REPAIR TO DRAIN, PATHS, FENCING, GATES, BOUNDARY WALLS ETC IN AOR OF AGE B/R-II OF GE (SOUTH) MAMUN

Amount

Taking down cement plaster / wall tiles including backing etc from brick/stone walls / concrete surfaces including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position including removal of debries out of MoD land complete all as specified and directed. Note: Reinforcement shall be cut as required to facilitate demolition.

M&L for use and waste of form work to sides of square, rectangular or polygonal, rough finished surfaces of concrete pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over in reinforcement cut to length, bent to shape required incl bending spirally cranking, hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9mm dia or securing with clips, all as specified.

M&L for mild steel TMT bars 5 mm dia and over up to and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Dismantling RCC posts and struts any section including taking out embedded portion in concrete and making good disturbed surface complete all as specified and directed.

Dismantling fencing, wire mesh any type and stacking at site complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregates) as in foundation, filling and mass concrete complete all as specified and directed.

Dismantling wrought iron or mild steel works of any description, any size and removing from site complete all as specified and directed.

S&F in repair Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. (each line wire to be measured) including taking out existing damaged barbed wire complete all as specified and directed.

M&L for mild steel fencing posts/struts including embeding in concrete and screwing etc. including securing bolts; including cutting tops to shape as directed, drilling holes, notching for wire, etc., flat iron fillets, round bars (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Fixing only chain link fencing including line wires of any mesh size, type and of any standard, rails, straining bolts etc including provision of binding wire complete all as specified and directed. Note: Supply of chain link fencing shall be measured & paid for separately.

Supply only chain link fencing of any mesh size, type and of any standard as approved including provision of binding wire complete all as specified and directed. Note:- Weight of chain link fencing shall be ascertained by BOO convened by GE.

S&F mild steel screw bolts (machine made) 5 to 10 mm dia of shank with hexagonal or square heads at one end and screwed the other, each screw end to be fitted with washers and one hexagonal or square nut exc 5 cm but n exc 10 cm long complete all as specified and directed.

M&L for preparation of new surfaces of steel or iron of any discription exc 10cm width or girth and providing two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old painted surface of steel of any description not other wise described over 10cm width or girth and applying one coat of synthetic enamel paint, white or tinted complete all as specified and directed.

Demolition of cement concrete (unreinforced) or tiling etc in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) in sub base of floors, finished even & rough to receive floor top finish complete all as specified and directed.

M&L in repairs for coloured machine pressed precast rubber moulded concrete interlocking (Grey/red/yellow) paver block 60 mm thick, M-35 grade of any shape and size with 6-8mm white cement layer mixed with pigment and coated with epoxy coating having high glossy finish confirming to IS 15658-2006 complete all as specified and directed.

Relaying concrete paver blocks any size 60mm thickness incl taking out complete all as specified and directed..

M&L for Sand filling as sand cushion under paver blocks using clean graded fine sand including levelling watering & compacting to required gradient complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in kerbs, coping, bed plates benching, floor by maintaining required gradient / undulation etc slightly rounded or chamferred angles and throating, complete all as specified and directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, including removal of deberies out of MoD land complete all as specified and directed.

M&L for brick work with fly ash bricks old size straight or curved on plan exc 6 mtr mean radius built in cement mortar (1:6) complete all as specified and directed.

All as per description of srl item No 25.00 here-in-before but EXCEPT BRICKS. Note: Servicable bricks retrieved from demolition of brick work shall be re-used.

M&L for brick work with fly ash bricks, old size as in half brick thick walls straight or curved on plan exc 6 mtr mean radius built in CM (1:4) complete all as specified and directed.

M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends etc complete all as specified and directed.

M&L in repairs for PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in surface channels & drains including demolition of existing PCC, complete all as specified and directed.

Demolition and breaking up drain pipes of size upto 300mm bore (Salt glazed ware, with hauncing etc incl necessary excavation (salt glazed stone ware, AC or reinforced concrete pipes ) set in cement mortar and taking out off trenches and removing the debris from the site complete all as specified and directed.

M&L for 300mm bore reinforced cement concrete pipes, class NP-3, laid in trenches and jointed, complete with collars, complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar 1:4 over on brick work or concrete surfaces of walls, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying three coats of white wash, complete all as specified and directed.

M/S BASOTRA BUILDERS (BID ID -3051830)

M/S HIMANSHU BUILDERS (BID ID -3052298)

M/S TARA CHAND CONSTRUCTION CO. (BID ID -3051262)

M/S NARESH KUMAR SHARMA (BID ID -3052336)

M/S DUGGAL CONSTRUCTION CO (BID ID -3051709)

VIJAY KUMAR LAKHNI (BID ID -3052072)

Bidder Name

VIJAY KUMAR LAKHNI

Walia trading co

M/S BASOTRA BUILDERS

M/S DUGGAL CONSTRUCTION CO

M/S TARA CHAND CONSTRUCTION CO.

M/S NARESH KUMAR SHARMA

M/S HIMANSHU BUILDERS