SPECIAL REPAIR TO BLDG NO T-54 T-61 AND T-40 AT 325 FD HOSP T-13 AT 117 TA BN AND SPECIAL REPAIR TO STATIC WATER TANKS AT AP-251 AT NAUSHERA GARRISON UNDER GE 862 EWS

Amount

Sch 'A' Part-I (B/R works) Demolition of cement concrete (unreinforced) in ground floors and paving n exc 15 cm th (below or above ground level), complete all as specified and directe. Note:No extra cost to be borne by govt in r/o flooring overleaped with tile mozzic floor incl screed .Thickness to be considered as total thickness of overleaping.

Demolition of Reinforced cement Concrete in Roofs,floors ( other than ground floors), beams,staircases,landings,chajjas,lintel band and similar suspended works.(reinforcement cut as required to facilitate demolition), complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided, complete all as specified and directed.

Demolition of Brick/stone work or block masonry built in cement morter of any descrption incl all necessary quions arches piilars etc, complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulaton boards/slabs/blankets, any thickness, including cover fillets cement, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

Dismantling Plain or corrugated steel sheeting or any other type, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

Dismantling timber scantling ,in fillets,rails,posts,rafters,purlin,etc under 40 sq.cm in section, complete all as specified and directed.

Dismantling timber scantling 40 sqcm and over in section fixed to any position as in unframed work. complete all as specified and as directed.

Dismantling mild steel work of any description not otherwise provided, complete all as specified and as directed.

Taking down cement plaster on brick/stone or conc surfaces including racking out joints hacking for key to any thickness scrubbing down with water etc.Note :(No extra cost shall be borne by Govt exchequer for any no of layers over leaping of tiles / mosiac finish), complete all as specified and directed.

Taking down chowkhats with shutter (without taking off from shutter) exc 1.5 sqm and n exc 4 sqm each and removing to store and making good to surface disturbed due taking down, complete all as specified and directed.

Taking down chowkhats with shutter (without taking off from shutter) n exc 1.5 sqm each and removing to store, complete all as specified and as directed.

Taking down door shutter of any desc exc 1 sqm but not exc 2 sqm and refixing in the same opening, complete all as specified and directed.

M&L for stone walling of random rubble masonry, uncoursed, well bonded, bedded and soilidly hearted, built in cement mortar (1:6), complete all as specified and directed., complete all as specified and directed.

All as per item No. 15 here-in-before but except stone, complete all as specified and directed.

M&L for extra over stone walling of any type of stone for hammer dressing to face stones and dressing of face beds with maximum depression on face from straight edge held against the dressed surface n exc 40 mm and joints, as specified, of random rubble walling, uncoursed or brought upto courses, complete all as specified and directed

M&L Cement concrete type B-2, 1:2:4 (40 mm graded stone aggregate) 75 mm thick as in floors laid in alternate pannels finished even and fair without using extra cement (note-no extra cost shall be claimed by contractor for use of vibrator), complete all as specified and directed.

M&L RCC design mix M-25 using 20mm gradded stone aggregate as in beams, deck slabs , chajjas and in shelves and like, complete all as specified and directed.

M&L Formwork to sides and soffits of floor or roof beam , beam hunching, girders, lintel, cantilevers, shelves including suports,overhangs etc, complete all as specified and directed.

M & L for mild steel TMT bars 10mm dia and over , cut to length ,bend to shape required, including cranking ,bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

All as per item No 21 here-in-before but exc 5mm dia upto 10m dia, as in stirrups.

M&L for rendering 20mm thick in cement mortar (1:4) on stone masonry surface, finished even and smooth without using extra cement complete all as specifed and directed.

All as per item No. 23 here-in-before but on stone masonry surface in CM 1:6, complete all as specified and directed.

M&L for rendering 5 mm thick on fair faces of concrete surfaces in ceilings in cement mortar 1:3 and finished fair and even without using extra cement.Height varing from 0 to 7m, complete all as specified and directed. Note: Contractor shall have no claim on if plaster is carried out in patches irrespective of any height.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

All as per item No. 27 here-in-before but plain steel sheet as in ridge, complete all as specified and directed.

M&L Cement concrete type C-2, 1:3:6 (40mm graded aggregate) 75 mm thick as in plinth protection laid in slope 1:12 from outer edge of the wall finished even and fair ,laid in alternate bays including providing 6 mm wide joints through out the thickness of plinth protection in concrete bays and in between walling and plinth protection,joint filled mastic filling comprising of one part of heated bituminous 85/25 and 3 parts of sand (all by weight) complete all as specified and directed.

M&L for 15mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes, complete all as specified and directed.

M&L for PCC 1:3:6 type C-0 using 12.5 mm graded aggregate as in hollow portion of pressed steel frame, complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded aggregate as in bed blocks, bed blocks of hold fasts, coping, sides of interlocking pvaers/tiles etc, complete all as specified and directed.

S&F vetrified ceramic tiles in light shade 600x600x10 mm thick as in floor set and jointed in neat cement slurry and pointing in white or coloured cement to match the colour of tiles complete all as specified, complete all as specified and directed.

All as per items No. 33 here-in-before but as in skirting, complete all as specified and directed.

S&F Factory made MS tubular Box type window of MS rolled steel section conforming to IS-1038 and shall be ISI marked manufactured by ISI approved manufacturer, openable frames shall be fabricated of sections as approved by Engr-in-Charge corner welded to form a solid fused welded joint handles shall be of z section welded with openable frame box steel section used in outer frame shutter frame and central frame shall be ERW secton of 16 gauge with fixing lugs to be fixed as per provision of IS-1038 except that top lugs shall not be provided , all shutters of windows shall be provided with 4 Nos friction free hinges, 2 Nos 75 mm tower bolts to each leaf of window one at top and one at bottom welded on 3 mm thick steel sheet piece of suitable size which shall be in turn welded to z section of steel window to provide suitable arrangement of using tower bolt. Glazed, gauged window , mild steel casement stays 300 mm with hinged joint and two plates with studs complete all as specified with all fittings and fixtures without glazing bars, including 3mm sheet glass, stainless steel wire mesh of 0.56 nominal dia and average width of aperature 1.18 mm etc, , complete all as specified and directed. Note -All as per Drg No- CEUZ /TD/ 1517/15 Sheet No-1/3,2/3,3/3.

S&F for steel ventilators with top hung shutter including hinges steel peg stay, complete all as specified and as directed.

S&F of guard bars/grills as specified in between glazed and fly proof window shutter(sand witching guard bars/grill) as per drg No CEPZ/TD-325/07 dt 04.12.07 primer coated, complete all as specified and directed.

S&F 1.25 mm Thick pressed steel frame 125x60mm for doors with one or more rebates incl supplying and fixing necessary fixing lugs. Hinges lock strike plate etc, complete all as specified and directed.

S&F 1.25 mm Thick pressed steel frame 105x60mm for doors with one or more rebates incl supplying and fixing necessary fixing lugs. Hinges lock strike plate etc, complete all as specified and directed.

S&F Plain framed, panelled shutters (any number of panels) with pannel of timber flat on both sides (feather edged) or of veneered particle board with commercial face veneers 35 mm thick 2nd class hard wood supplied and fitted to chowkats., complete all as specified and directed.

M&L for 35 mm thick second class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc, (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass, etc, size of members of shutter as specified in SSR Part-I, Section 8, clause 8.20 (a), fitted to chowkats, complete all as specified and directed.

S&F for 300mm ordinary rat tail rod pattern springs including roller plate, complete all as specified and directed.

S&F 2nd class hard wood small fitting such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary laboures articles n.exc 200cu.cm each, complete all as specified and directed.

S & F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tacks of galvanised wire staples, complete all as specified and directed.

S&F Aluminium handles, cast type, anodised 150mm long, complete all as specified and directed.

S&F aluminium, anodised barrel tower bolts of extruded section and fixed of size 200 mm long, complete all as specified and directed.

S&F aluminium alloy anodised sliding door bolt with fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed of size 200 mm , complete all as specified and directed.

S&F for Curtain Rod of stainless steel 25 mm dia fancy type complete and hanging hooks/brackets / end caps of length 1.5 mtr to 1.8 mtr, complete all as specified and directed.

M&L for providing & fixing of 4mm thick designer ceiling board (Make : Everest/Ramco/) in ceiling fixed with screw as per manufactures instructions, laid on hot dipped galvanized iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick galvanized steel sheet & of size 24x32x300mm and spaced at 12mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. Hangers of GI wire 4mm dia to be fixed by approved rowl plug, level adjusters and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall flush fitting of 1200 long cross tee with (double stitching) to be inter locked between main runners at 600mm centre to from 1200x600mm modules cross tee longer than 600mm modules to be formed by fitting 600mm long cross tee, tee perimeter wall angle shall be of 0.45mm thick galvanized steel of size 19x19mm and 300mm long of white colour, complete all as specified and directed.

Preparing newly plastered surface and applying two coat of oil bound distemper, complete all as specified and directed. Note-Painting shall be done by Painting roller.

M&L preparing new wall surfaces and applying two coats of cement base paint over a coat of primer (Note-painting shall be done by Painting roller), complete all as specified and directed.

Preparing of old plastered wall surface by complete removal of existing treatment and apply two coat of oil bound distemper over a coat of wall care putty, complete all as specified and directed.(Note-painting shall be done by Painting roller).

M&L for applying two coats of white washing on walls including preparation of old plastered surfaces, complete all as specified and directed.

M&L for two coats of synthetic enamel paint on new steel surfaces over 10cm width or girth including preparation over a coat of red oxide Zinc chrome primer, complete all as specified and directed.

M&L for one coat of synthetic enamel paints over a coat of on old steel surfaces over 10cm width or girth including preparation of surfaces, complete all as specified and directed.

M&L for two coats of synthetic enamel paint on new wooden surfaces incl prep over a coat of pink primmer, complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, old size, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:4, complete all as specified and directed.

M&L Formwork to chullah hoods,chajjas, throughand similar item including edges , etc, complete all as specified and directed.

S&F Stainless Steel wire cloth 0.36 mm any position nominal dia of wire and 1.20 mm average width of aperture fixed with tinned tacks or galvanised wire staple, complete all as specified and directed.

M&L for 25mm thick PCC(1:2:4) type B-0 using 20mm graded stone agg as in sub base finished even and rough, complete all as specified and directed.

M&L for 3 mm thick wall care putty on wall after preparation of surfaces, complete all as specified and directed.

M&L for 100 mm thick Cement concrete type E- 2, 1:5:10 (40mm graded aggregate) as in sub base of floors,Pavings complete all as specified and directed .

M&L for chequered cement concrete tiles 30cmx30cmx25mm thick set and jointed and pointed in neat cement slurry as inpath,pavings with gray cement and no pigment over & including screed bed or bedding layer of mortar 20 mm thick for laying floor tiles in CM 1:4, complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M & L for cement concrete type C1 1:3:6 (using 20 mm graded crushed stone aggregate) as in surface channel and drains including formwork complete all as specified and directed.

Extra for forming fair finished drain or channels 30cm inner girth in cement concrete using extra cement including forms, mould, mitred/stopped ends etc, complete all as specified and directed.

S&F Mild steel screw bolts exc 5 cm length not exc.10 cm length(machine made) with hexagonal or square heads at one end and screwed the other , or screwed both ends , each screwed end to be fitted with washers and one hexagonal or square dia of shank 11to 15mm, complete all as specified and directed.

S&F Mild steel holding nut bolts exc 22.5 cm length not exc.30cm length(machine made) with hexagonal or square heads at one end and screwed the other , or screwed both ends , each screwed end to be fitted with washers and one hexagonal or square dia of shank 11to 15mm, complete all as specified and directed.

S&F(plain or chequered ) channels ,square cut or notched ( oridinary and counter sunk) forming holes , w/o any attatchment., complete all as specified and directed.

M&L for rendering 15 mm thick in cm 1:4 on brick or concrete surfces of wall,column finished even and smooth without using extra cement, complete all as specified and directed. Note:-No extra cost shall be borne by Govt exchequer for any plaster and for any height.

All as per item No. 70 here-in-before but on brick masonry surface in CM 1:6, complete all as specified and directed.

S&F 18-20 mm thick machine cut kota stone slab (area of each slab nexc 0.27 Sqm except space constraint) in flooring laid and jointed with gry cement slurry Mixed with pigment to match the shade of the slab incl rubbing and mirror polishing over and including 15mm thick screed bed in CM1:6 including dismantling old kota stone slab flooring, complete all as specified and directed.

All as per item No. 72 here-in-before but as in riser to steps, skirting, dado, window cills fixed with cement mortar 1:4, complete all as specified and directed.

M&Lfor Green Marble work 18 to 20mm thick (table rubbed and polished) in floor border , steps, jambs, pillars, windowcills, cooking platformsand like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigmento match with marble shade of following type, complete all as specified and directed.

M&L for RCC design mix M-30, as in raft footing basement slab etc, complete all as specified and directed. Note :- The work shall be executed in highly restricted area.

M&L for RCC design mix M-30, as in walls retaining walls any thickness etc, complete all as specified and directed. Note :- The work shall be executed in highly restricted area.

M&L for formwork to faces of curved surfaces of walls, well steining well curves and similar work including attached illasters, butresses, etc. Vertical or to batter, complete all as specified and directed.

M&L for rendering 10 mm thick on brick work or concrete sufaces in cement mortar 1:4 finsished even and smooth without using extra cement inlcuding mixing integral water proofing compund in the proportion as mentioned in manufacturer's instructions, complete all as specified and directed. (Water proofing compound to be measured and paid for separately)

Supply only liquid water proofing compound conforming to IS, complete all as specified and directed.

100mm thick PCC (1:4:8) type D-2 (using 40mm gradded crushed stone agregate) as in sub base of floor, complete all as specified and directed.

M&L for 25mm thick sand filling under floors or in foundation including watering and consolidation for laying interlocking tiles, complete all as specified and directed.

M&L machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80mm thickness, M-40 Grade, set and joint filled with sand, complete all as specified and directed.

Erection and refixing of roof trusses (framed), trussed, purlins, rafter, crane, gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, complete all as specified and directed.

Sch 'A' Part-II (E/M works) Taking down U/S aluminium point wiring (light, fan, socket or power) complete including fittings and fixtures such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing materials for taking credit (credit for above items should be amde as per conditions seperately) and making good the disturbed, complete all as specified and directed.

M&L for point wiring for following types of electrical points with two runs of FRLS PVC insulated unsheathed, 1100 V grade cable multi stranded copper conductor of size 1.5 sqmm drawn through medium grade PVC pipe/ casing and caping in wall/ surface in ceilings including provn of pressed steel terminal boxes of suitable size with 2.8 mm thick plastic laminated sheet cover for mounting switches, socketes and regulator alongwith continous earth wire of PVC insulated, unsheathed, 1100 V grade cable multistranded copper conductor of size 1.5 sqmm all as specified and directed by Engineer-in-Charge. (Note : Cost of cutting chasing and making good to disturbed surface to match with existting surface are deemed to be included in quoted rate).

One light/ fan point controlled by one switch on way, complete all as specified and directed.

One socket out let 5 Amps point controlled by one switched one way on same switch board, complete all as specified and directed.

One socket out let 5 Amps point controlled by one switch one way on independent switch board, complete all as specified and directed.

All as per item No. 84 here-in-before but point wiring with 2.5 sqmm for socked outlet 15 Amps point controlled by one switch, complete all as specified and directed.

Supply & fix in replacement of switch piano flush type single pole, one way 6 Amps 230 volts, complete all as specified and directed.

Supply & fix in replacement of switch piano flush type single pole, one way 15 Amps 230 Volts, complete all as specified and directed.

Supply & fix in replacement of socked outlet 2 in 1, 3 pin 5 Amps flush type suitable for 230 V AC, complete all as specified and directed by GE.

Supply & fix in replacement of socket outlet 2 in 1, 3 pin 5/15 Amps flush type suitable for 230 V AC, complete all as specified and directed.

Supply & fix in replacement of ceiling rose three terminals/PVC/Polycarbonate, isolated body on PVC board, complete all as specified and directed.

Supply & fix in replacement of stepped type electronic fan regulator heavy duty flush type, complete all as specified and directed.

Supply and fixing LED lights fitting 1 x20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site or directed, complete all as specified and directed.

S & F in replacement lamp holder insulated body PVC/ Polycabonate type with back plate suitable for batten/angular/pendent holder fittings , complete all as specified and directed.

S&F LED lamp 7/9 suitable for lamp holder, complete all as specified and directed.

Taking down fan, ceiling cable end, dismantling blades and removing fan blades and eposited to MES store, complete all as specified and directed.

Refixing the ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan, complete all as specified and directed.

Supply & fix in replacement of sheet metal enclosure for MCB distribution board single pole & neutral 230 volts 4 way double door, 200 Amps rated bus bar complete including fixing the DB inside the wall and making goood disturbed wall surfaces to match with existing specification, complete all as specified and directed. (Note: MCBs will be measured separately).

S&F in replacement MCB single pole 230 volt any rating from 6 to 40 Amps, with rupuring capacity 10 KA inculding providing thimble for out going cable, complete all as specified and directed.

S&F in replacement MCB SPN 230 volt any rating form 6 to 40 Amps with rupturing capacity 10 KA including providing thimble for out going cable, complete all as specified and directed.

S&F in replacement bulk head luminaries, with 1x9 W/1x10W bulk head luminiaries LED light driver holder etc complete with all accessories and including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

Supply and fixing in replacment of 1100 volts grade heavy duty cable of size 10 sqmm PVC insulated stranded aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connnections suspended by insulating hangers not more than 1metre apart including 4mm suspension wire, one twin core cable flat or circular, complete all as specified and directed.

M&L for earthing complete with steel earth plate electrode 60 cm x 60 cm x 6 mm thich buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanized iron earth wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron and steel earthwire protected by provision of GI medium grade pipe 15 mm bore including provision of concrete pit made from PCC (1:3:6) type C-1 (using 20 mm graded stone aggregates) with 40 mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 Kgs/Sqm) and frame of angle iron 25 x 25 x 6 mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape, GI medium grade 20 mm bore pipe for watering perforated at Bottom, 1.75 metre long placed on top edge of earth plate, common salt & charcoal filling, test point made out of 17 mm x 8mm FI with fixing arragnement, funnel, wire mesh and eath work in hard/ dense soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 5 of SSR Part-I connected to earth test point all as specified or indicated including testing on completion, complete all as specified and directed.

Supply & fix in replacment sheet metal enclosure MCB distribution board single pole & neutral 240 volts 8 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good istributed wall surfaces to match with existing specification, complete all as specified and directed. (Note-MCBs will be measured separately).

S&F LED building security light 35 watt with pressure die-cast housing with individual LEDs as light source and lens embedded PC cover having TOP opending separate driver compartment with IP 66 protection and impact resistance of IK 07 complete with connection electrically to ceiling rose to fitting using PVC insulated and overall sheathed flexible copper conductor cable of size 1.0 sqmm, complete all as specified and directed by GE.

M/S IMRAN MAJID (BID ID -3394718)

M/S Narinder Pal Choudhary (BID ID -3402037)

vijay kumar (BID ID -3394426)

M/S BADRI NATH GUPTA (BID ID -3392223)

M/S Darshan Kumar (BID ID -3402904)