SPECIAL REPAIRS TO AND UP-GRADATION OF CERTAIN EXISTING (NON-LCA SMQs) CIVILIANS AND AIRMEN SMQs AND CERTAIN B/R AND E/M SANCTIONED WORKS IN DOMESTIC AND TECHNICAL AREA

Amount

SCHEDULE A BOQ

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Note for Item No 1 :- The material obtained from demolition shall be disposed outside MD land and the unit rate is deemed to be inclusive for this provision

M&L Two coats of cement slurry in CM(1:2) proportion on complete horizontal and vertical area of sunken floor over 15mm thick base plaster in CM (1:4) over sunken portion/roof etc mixed with WPC complete all as specified and as directed.

Note for Item No 4 :- WPC will be measured and paid separately under relevant item here-in-after

Supply Only integral water proofing compound complete all as specified and as directed.

M & L applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm including cleaning surface complete all as specified and as directed.

M&L Plain Cement Concrete Type E2 1:5:10 (using 40 mm graded granite stone aggregate) in sunken floors, filling and mass concrete complete all as specified and directed.

S&F in repairs vitreous china squatting pan 'Orissa' Pattern size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe ) including provision of lime concrete bedding complete all as specified and as directed.

S&F PVC (SWR) 110mm bore S Trap including taken down existing one complete all as specified and as directed by Engineer-in-Charge

S&F Bib Cock with wall flange screwed down screwed for iron pipe in repairs 15mm bore including taking existing one complete as directed by Engr-in-charge.

S & F 20 mm outer dia of pipes 3-layer PP-R (Polypropylene random copolymer) pipes concealed pipes SDR 7.4 (PN-16 @ 20°C) UV stablised and anti-microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings, including taking down existing pipe of any description complete to walls, ceilings or in floors etc. all as specified and directed.

Note for item No 12 :- (a) The unit rate shall be include for taking down existing pipe and necessary connections and all fittings as directed.

(b) The unit rate shall include the cost of short lengths, with all pipe fittings such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc and fixing accssories such as pipe hooks, screws clamps etc

(c ) Wall thickness of pipes shall be all as per IS : 15801

M & L Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick wall complete all as specified and directed.

S&F in repair PVC Dual flush ceramic colour , low level, 10 litres capacity, star white with inlet float ball valve, PVC flush pipe and handle, making proper fixing and hanging arrangements Cat Part No 21029 of - hindware or equivalent all as specified and as directed.

S&F PVC connections 15mm size with PTMT nuts of length 600 mm including taking down existing one complete all as manufactures and all as specified and directed by Engineer- In - charge.

S&F Angular stop cock with wall flange, valves high pressure screwed both ends iron pipe or for unions 15mm dia, including taking down existing one Complete all as specified and as directed. Make:- CAT Part No CQT-23059 of JAGUAR or equivalent to Hindware/Cera

M&L Vitrified Ceramic tiles 10 mm thick, LIGHT shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including screed bed or bedding layer, 15 mm thick in Cement Mortar 1:6 including dismantling existing tile and removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L Vitrified Ceramic tiles 10 mm thick, LIGHT shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including back coat of 10 mm thick in Cement Mortar 1:4 including taking down existing tile and removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Note for Item No 20 & 21 :- (i) Vitrified tiles are classified under group B1a of the international Standard for ceramic tiles ISO: 13006. Tiles shall be hard, dense, impervious and frost resistant. Water absorption of tiles shall be less than 0.5% and flexural strength (Modulus of Rupture) shall be more than 35 N/Sqmm. (ii) The manufacturer's test certificate and individual test certificate of Tiles must be submitted for approval by the concerned authority prior to installation.

M&L Joint free Non Skid Ceramic Tiles 7 to 8 mm thick [Square or Rectangular], area of each tile exceeding 0.06 Sqm and not exceeding 0.18 Sqm, as in Floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including screed bed or bedding layer ,10 mm thick in Cement Mortar 1:4 including dismantling existing tile and removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L Glazed ceramic tiles 450 x 300 mm x 7/8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles on vertical surface such as dado including 10mm thick 1:3 backing coat including taking down existing tile and removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Note for Item No 23 & 24 :- The manufacturer's test certificate and individual test certificate of Tiles must be submitted for approval by the concerned authority prior to installation.

Taking down chowkhat or frame(wooden/steel) not exceeding 1.5 Sqm each with shutter (with out taking off shutters from the frame) all as specified and as directed.

S & F powder coated aluminium work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as directed by the Engr-in-Charge. Note:- minimum thickness of powder coating shall be 50 micron

M&L powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed. Note:- minimum thickness of powder coating shall be 50 micron

Supply and fixing 4mm thick figured glass pin head type and glazing with powder coated aluminium beads in squares n. exc. 0.50 Sqmtr each pane complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube complete all as specified

S&F Factory made Solid PVC Door Shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified.

Supply and fixing 75mm long Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed

S&F 100 mm long anodised aluminum handles, cast type, complete all as specified and as directed by Engineer-in-Charge

Taking down chowkhat or frame(wooden/steel) exceeding 1.50 Sqm but not exceeding 4.0 Sqm each with shutter (with out taking off shutters from the frame) all as specified and as directed.

M&L Second class hard wood plain, solid, straight Chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

M & L Cutting holes in stone wall exc half brick and n.exc one brick in cement mortar for inserting hold fasts/lugs and making good dismantled portion in cement mortar 1:3 or 1:2:4 type B-1 concrete as required complete all as specified and as directed.

S&F MS work (flat iron) 25mm x 3mm thick in small articles such as hold fast and similar small articles conforming to Fe 290 Gde E-165 complete all as specified and directed.

Supply and Fixing 30 mm thick factory made flush shutter solid core construction with block board core and plywood face panels, comercial type on both faces complete all as specified and directed.

S&F 30mm thick, second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); all as specified and directed.

S&F 50mm long Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F 75 mm long aluminum anodized barrel tower bolt extruded section complete as directed by Engr-in-charge. .

S&F 125mm long mild steel, wire, type I Gate and shutter, hooks and eyes complete all as specified and directed.

M&L preparation of new wood or wooden surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed

M&L preparation of old wood or wooden surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed

Note for item No 43 & 44 :- (a) Synthetic enamel paint shall be of 1st quality manufactured by the standard firms of make as specified.

(b) The contractor shall inform the GE, within three weeks of the acceptance of the tender, the brand/names of the manufacturers of paint proposed to be used in the works and submit samples thereof and obtain prior written approval of GE before their use in works.

(c) The contractor shall when so required by the GE, produce certificate from the manufacturer or their representative to establish that the brands of paints purchased by the contractor from them, satisfy the requirements of the relevant Indian Standards. Tint of paint, will be approved by the GE.

(d) Paints shall be obtained direct from approved manufacturer or from their authorized agents only of respective brands mentioned below and brought to site in sealed containers. The paint so procured shall be of first quality of any approved make as per list of makes specified. i. Berger Paints (Luxol), ii. Jenson & Nicholson (Brolac), iii. Shalimar Paints(Superlac), iv. Goodlass Nerolac (Nerolac), v. Asian Paints(Apcolite)

(e ) Unless otherwise specified the tints of paint shall be as approved by the GE

(f) The contractor shall submit samples of the paints proposed for the work along with results of tests conducted in approved laboratory as directed by the Engineer-in-Charge for approval.

(g) The surface shall be thoroughly cleaned and dusted. All dirt scales oil and grease shall be thoroughly removed before painting is started. The prepared surface shall be inspected and approved by the GE before painting is commenced. The weather shall not be foggy/rainy, dusty or windy. The suitability of the weather will be determined by the Engineer-in-Charge.

(h) No hair marks from the brush or clogging of paint buddles shall be left on the work. Surface shall ordinarily not be painted until it has dried up completely. Trial patches of paint shall be laid at intervals to check if drying is satisfactory.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm complete including taking down existing one all as specified and directed.

S & F 4mm thick plain sheet glass ordinary quality and glazed with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and directed.

S&F 100mm long Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F 150mm long Extruded aluminium alloy handles , fabricated type, anodised complete all as specified and directed.

S&F 150 mm long aluminum anodized barrel tower bolt extruded of section complete all as specified and directed.

S&F 200mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extrudud sections or cast- aluminum alloy and fixed complete all as specified and as directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, with overal length of cover plate 150mm long, fixed in floor complete all as specified and as directed.

S&F 300mm long Mild Steel ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and as directed.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints of 110 mm bore fixed to wall including taking down existing one complete all as specified and as directed by Engineer-in-Charge

S&F PVC bends 110mm bore including taken down existing one complete all as specified and as directed by Engineer-in-Charge

S&F PVC (SWR) 110mm junction (single T) equal or unequal provided with access door including taking down existing one complete all as specified and as directed.

S&F PVC (SWR) 110mm bore junction vent cowl all as specifed including taken down existing one complete all as specified and as directed by Engineer-in-Charge

S&F in repair PVC (SWR) branch piece, double (double Y) 110mm bore equal or unequal complete all as specified and as directed by Engineer-in-Charge

S&F in repair PVC (SWR) 110mm bore branch piece, single (single Y) equal or unequal complete all as specified and as directed by Engineer-in-Charge

S&F Wall mounted Shower Arms 190mm long flat shape for wall mounted shower with flange including taking down complete all as specified and directed.

S&F in repairs Overhead Shower ø120mm Round Shape Single Flow (ABS Body Chrome Plated with Gray Face Plate) with Rubit Cleaning System In repairs complete all as specified and as directed.

S&F in repairs Chromium plated wall mixer with provision for over head shower with 115mm long bend pipe on upper side connecting legs and wall flanges complete all as specified and directed.

S&F in repairs PVC (SWR) floor trap 75mm dia of outlet pipe, plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F Pillar taps 15mm bore CP with capstan head screwed down high pressure screwed for iron pipe including taking existing one complete as directed by Engr-in-charge.

S&F Wash hand basin vitrous china (flat back and angle back Type) size 550x400mm excluding taps, waste chain, and plug and porceline stopper but including brackets, cutting for and pinning in ends of brackets or erecting stand with waste pipe etc including taking down existing one complete as directed by Engr-in-charge.

S&F 32 mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed including taking down existing one complete all as manufactures and all as specified and directed by Engineer- In - charge

M&L 32mm bore Low density poly ethylene pipes (LDPE) of pressure rating 6 kg/ cm2 laid in trenches all as specified and as directed.

M&L 40mm bore Low density poly ethylene pipes (LDPE) of pressure rating 6 kg/ cm2 laid in trenches all as specified and as directed.

S&F PVC (SWR) pipes single socket in any length with rubber ring joints of 75 mm bore fixed to wall including taking down existing one complete all as specified and as directed by Engineer-in-Charge

S&F PVC (SWR) 75 mm dia junction vent cowl all as specifed including taking down existing one complete all as specified and as directed by Engineer-in-Charge

S&F PVC (SWR) 75mm junction (single T) equal or unequal provided with access door including taking down existing one complete all as specified and as directed.

S&F PVC (SWR) branch piece (single Y) 75mm bore equal or unequal provided with access door including taking down existing one complete all as specified and as directed by Engineer-in-Charge

S&F in repair CP Soap dish all as specified and as directed.

S&F in repair Towel rail 24" long for wash basin complete all as specified and as directed.

S&F 600X450 mm bevelled edge mirror fixed with 04 Nos Stainless steel studs including taking down existing one complete all as specified and as directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar and removal of debris complete all as specified and directed.

M&L Bullnosed chequered cement concerete tiles 32cm x 20cm x 30 cm thick machine pressed set jointed and pointed in neat cement slurry as in treads & landings and cut and pointed using gray cement and pigments over and including 15mm thick screed bed or bedding layer of cement mortar (1:4) complete all as specified and as directed by Engineer-in-Charge

M&L Cement concrete tiles 20cm x 20cm x 20mm thick with grey cement and pigments, machine pressed for work on vertical surfaces as in skirtings, dados and risers of steps set jointed and pointed in neat cement slurry in floors, and cut and polished; over a 10mm thick backing coat of cement mortar 1:3 complete all as specified and as directed by Engineer-in-Charge

Taking down cement plaster on brick or stone walls, or concrete or ceilings etc., including raking out joints, hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises and leaving the work clear of any plastering complete all as specified and directed.

M&L Rendering 5mm thick in CM 1:3 on ceilling of concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed

M & L Preparation of new plastered or unplastered surface of ceilling, and applying two coats of white wash complete complete all as specified and as directed .

M & L Preparation of old plastered or unplastered surface of ceilling, and applying two coats of white wash complete complete all as specified and as directed .

M&L rendering 15mm thick in cement plaster 1:4 on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing finished even and smooth without using extra cement complete all as specified and as directed

M & L preparation of new plastered or unplastered surface of wall and applying two coats of CBP over a coat of alkali resistant priming paint complete all as specified and as directed.

M & L preparation of old plastered or unplastered surface of wall and applying two coats of CBP complete all as specified and as directed.

M&L rendering 15mm thick in cement plaster 1:6 on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing finished even and smooth without using extra cement complete all as specified and as directed

M & L preparation of new plastered or unplastered surface of wall and applying two coats of OBD over a coat of alkali resistant priming paint complete all as specified and as directed.

M & L preparation of old plastered or unplastered surface of wall and applying two coats of OBD complete all as specified and as directed.

S&F CP sink cock with swinging casted round shape spout screwed down screwed for iron pipe in repairs 15mm bore including taking down existing one complete all as specified and as directed.

S&F Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm fixed in repairs all as specified and directed.

S&F Waste coupling of PTMT (half or full threaded) of 40mm bore dia of discharge pipe (Minimum weight 60 gms) complete all as specified and directed.

S&F in repairs Plate rack of size 65 cm x 96 cm made of stainless steel, complete all as specified and directed.

M&L Water proofing treatment of existing roofs as per details given below after complete removal of existing water proofing treatment and expose of top surface of RCC slab of any thickness, any type by stripping out old tar felt over roofs, parapets, chimney stacks etc laid horizontally or vertically including taking out layer of cement plaster etc and cleaning the surface with water and using wire brush including removing debris to outside the MOD land complete all as specified and as directed :-

Note for Item No 102 :- (a) Surface should be free from any loose paint, dust or grease. Remove all existing bitumen coatings completely by using intense wire brushing, high speed water jet & vacuum cleaner for thorough cleaning of the surface to avoid ‘Peeling off’ problems.

(b) All cracks at corner joints, channels and parapets should be properly treated. For filling cracks upto 3mm crack seal material of M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical to be used. Bigger cracks, damaged portions & hollow areas must be repaired with polymer modified cement mortar.

(c) Apply a coat of self priming smart care damp proof ultra (Code 5698) of M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical with 33% dilution with water using brush/roller on newly plastered surface after curing as per IS-456 and allow to dry for 4 to 6 hours (dilution & forced coverage requirement strictly as per manufacturer’s instructions).

(d) After the primed surface has dried, apply first coat of water proofing smart care damp proof ultra (Code 5698) of M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical using brush/roller on the same primed surface & allow to dry for 4 to 6 hours.

(e) Prepare for apply 2nd coat of water proofing smart care damp proof ultra (Code 5698) of M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical using brush/roller on the same surface. The temp to be maintained 25 to 35° C through out the all above application work.

(f) In case of severe dampness an additional coat of damp proof materials to be applied.

Note for item No 102 to 108 :- (i) The work shall be carried out through authorized and qualified applicators of the following manufacturers only. MOU to be submitted before commencement of work. Make : M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical

(ii) A performance guarantee certificate for 10 years shall be submitted by the contractor to the GE on completion of work as specified.

(iii) The unit quoted rate is deemed to include taking down of water pipeline, tanks, wires (etc) found on roof and refix at the original position after complete treatment of roof.

(iv) The unit quoted rate shall be inclusive of material, all labours, tools and plants including scaffolding required for working upto approx 7.5 mtr height from natural ground level.

(v) The unit rate quoted for item is deemed to include for Removing of accumulated earth of any width and depth upto 15 cm cleaning/cutting the grass with hand operated petrol/kerosene driven grass cutting machine and removing the grass waste around 3 m from plinth protection to outside MD land.

(vi) Adoption of necessary safety arrangement like safety belts, ropes, helmets, netting etc. which are required for safety of working labour at height exceeding 3 to 25 mtr height shall be mandatary and deemed to be included in the unit rate quoted.

M&L providing PCC 1:2:4 type B1 using 20mm graded stone aggregates as in roof or in any position to bring upto the slope of average thickness of 50 mm including Dismantling existing cement concrete/ roof tiles and removing debris to outside MOD land complete all as specified and directed.

M & L rendering 10 mm thick in CM 1:3 on concrete roof surfaces and finish the surface even and smooth without using extra cement including mixing water proofing compound as per manufacturer’s instructions and complete all as specified and directed.

M&L Plain cement concrete 1:2:4, type B-0 using 12.5mm graded aggregate as in roof kerbs,benching rounded or chamfered on edge complete all as specified complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6, type C-1, using 20 mm graded crushed stone aggregate as in plinth protection finished even aned fair without using extra cement complete all as specified and directed.

Taking down steel tubing 15 mm bore and connections including cleaning and refixing of old GI tubing 15mm bore in wall/ ceiling / floor including connections in new or old position complete all as specified and directed.

Taking down steel tubing 20mm bore and connections including cleaning and refixing of old GI tubing 20mm bore in wall/ ceiling/ floor including connections in new or old position complete all as specified and directed.

M&L 25mm dia mild steel powder coated drapery rod out to length required without joint in between and fixed at openings including taking existing one complete as directed by Engr-in-charge.

M&L Mild steel powder coated brackets for holding the drapory rod and fixed to wall with MS screw including taking down existing one complete as directed by Engr-in-charge.

Supply and Fixing in repairs Mild steel powder coated fancy type brackets fixed at both the end of drapery rod of same colour and type of drapaery rod as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed

S & F Mild steel work in framed work such as grills and similar work including framed guard bars, barred iron doors, ladders, framed balusters etc., including of fixing of sheet steel or other covering to doors etc., to be prepared for hanging /sliding with or including either hooks or hinges or steel hanging door fittings etc., confirming to Fe 410-0 or Fe 310-0 work complete all as specified and directed.

M&L preparation of new steel surfaces of any description exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of redoxide primer on new steel surfaces complete all as specified and as directed.

M&L preparation of old steel surfaces of any description exc 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

Note for item No 126 & 127 :- (a) Synthetic enamel paint shall be of 1st quality manufactured by the standard firms of make as specified.

(b) The contractor shall inform the GE, within three weeks of the acceptance of the tender, the brand/names of the manufacturers of paint proposed to be used in the works and submit samples thereof and obtain prior written approval of GE before their use in works.

(c) The contractor shall when so required by the GE, produce certificate from the manufacturer or their representative to establish that the brands of paints purchased by the contractor from them, satisfy the requirements of the relevant Indian Standards. Tint of paint, will be approved by the GE.

(d) Paints shall be obtained direct from approved manufacturer or from their authorized agents only of respective brands mentioned below and brought to site in sealed containers. The paint so procured shall be of first quality of any approved make as per list of makes specified. i. Berger Paints (Luxol), ii. Jenson & Nicholson (Brolac), iii. Shalimar Paints(Superlac), iv. Goodlass Nerolac (Nerolac), v. Asian Paints(Apcolite)

(e ) Unless otherwise specified the tints of paint shall be as approved by the GE

(f) The contractor shall submit samples of the paints proposed for the work along with results of tests conducted in approved laboratory as directed by the Engineer-in-Charge for approval.

(g) The surface shall be thoroughly cleaned and dusted. All dirt scales oil and grease shall be thoroughly removed before painting is started. The prepared surface shall be inspected and approved by the GE before painting is commenced. The weather shall not be foggy/rainy, dusty or windy. The suitability of the weather will be determined by the Engineer-in-Charge.

(h) No hair marks from the brush or clogging of paint buddles shall be left on the work. Surface shall ordinarily not be painted until it has dried up completely. Trial patches of paint shall be laid at intervals to check if drying is satisfactory.

S&F Decorative laminates of 0.90 mm thick type matt finish, colour and pattern as approved including taking down existing one complete all as specified and as directed.

Supply & fixed in repairs of 18mm thick, 7 ply, plywood, grade BWR, type BB fixed to wooden frame work in wall with nails complete all as specified.

S&F Stainless steel thali basket of size 600x 500x 100mm Including taking down the existing one complete all as specified and as directed. Make : Butterfly or equivalent make approved

S&F Stainless steel cutlery basket of size 530 x 505 x 100 mm Including taking down the existing one complete all as specified and as directed. Make : Butterfly or equivalent make approved

S & F Stainless steel spring hinges of size of approved pattern and make suitable for base/wall unit of modular kitchen Including taking down the existing one complete all as specified and as directed. Make : BIR SS or equivalent make approved

S&F Magnetic catches with 8mm dia steel ball and brass body and striking plate including taking down complete all as specified and directed.

S&F Stainless steel plain basket of size 530 x 505 x 100mm Including taking down the existing one complete all as specified and directed. Make : Butterfly or equivalent make approved

S & F stainless steel bottle basket of size 200x 508x 431mm including taking down complete all as specified and directed. Make : Butterfly or equivalent make approved

S & F Stainless steel telescopic slider of 500 mm of approved pattern and make suitable for drawer in base unit of modular kitchen including taking down the existing one complete all as specified.

S & F Continuous (piano) hinges, stainless steel bright finish or electrogalvanised of 30mm width of flaps (when open) complete including taking down all as specified and as directed.

S & F stainless steel handles of size 150 mm of approved pattern and make suitable for Base/Wall unit of modular kitchen Including taking down the existing one complete all as specified and as directed. Make : Spykar or equivalent make approved

S & F Brass 4 lever cupboards locks grade I, size 65mm, Including taking down existing one complete all as specified and as directed by Engneer-in-Charge

S&F 40 mm dia cupboard knobs fixed with nut, screw and washer of brass polished complete including taking down existing one all as specified and as directed.

M&L 6 mm thick teak wood lipping for 18/19 mm thick particle board fixing with nails complete including taking down all as specified and as directed.

S & F 25 mm outer dia of pipes 3-layer PP-R (Polypropylene random copolymer) pipes concealed pipes SDR 7.4 (PN-16 @ 20°C) UV stablised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings, including taking down existing pipe of any description complete to walls, ceilings or in floors etc. all as specified and directed. Make : SFMC, Reliance Industries, KPT

Note for item No 150 :- (a) The unit rate shall be include for taking down existing pipe and connections and all fittings as directed.

(b) The unit rate shall include the cost of short lengths, with all pipe fittings such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc and fixing accssories such as pipe hooks, screws clamps etc

(c ) Wall thickness of pipes shall be all as per IS : 15801

S & F 20mm outer dia of pipes PPR gate valves (brass insert) as per requirement of sites including taking down existing one complete all as specified and directed.

S & F 25mm outer dia of pipes PPR gate valves (brass insert) as per requirement of sites including taking down existing one complete all as specified and directed.

S&F PVC bends 75 mm bore including taking down existing one complete all as specified and as directed by Engineer-in-Charge

Surface excavation n.exc. 30 cm deep and averaging 15 deep and getting out in hard dense soil complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface complete all as specified and directed.

Excavating over areas, n exc 1.5 m deep and getting out in hard/dense soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and getting out in hard dense soil

Removing excavated soil exc 250m and n exc 500m and deposting where directed at a level n exc 1.5 m above the starting point complete all as specified and directed.

M&L Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard dense soil complete all as specified and directed..

M&L Brickwork with fly ash bricks(old size), straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed..

M&L Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size, polished confirming to IS-15658 of 80mm thickness M-40 grade, laid over and including M sand cushion of 50mm thick complete all as specified and directed.

Note for Item No 164:- The manufacturer's test certificate and individual test certificate of paver blocks must be submitted for approval by the concerned authority prior to procurement.

M & L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified

M&L for hardcore of gauge n.exc 63 mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for hardcore of gauge exc 63 mm but n exe. 100mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for PCC 1:3:6, type C-2 using 40 mm graded stone agg as in foundation filling and mass concrete complete all as specified.

M&L for PCC 1:4:8, type D-2 using 40 mm graded stone agg as in foundation filling and mass concrete complete all as specified.

M&L 100mm thick Cement concrete 1:2:4, type B-2, using 40mm graded aggregate as in flooring complete all as specified

M&L 100mm thick Cement concrete 1:4:8, type D-2, Using 40mm graded aggregate as in flooring complete all as specified

M&L 100mm thick Cement concrete 1:2:4 type B-1,using 20mm graded aggregate as in flooring complete all as specified

M&L plain cement concrete 1:2:4, type B-1 using 20mm graded stone aggregate as in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates etc including weathering, slightly rounded for chamfered angles and throating, complete all as specified and directed.

M&L Steel work in tubular trusses, purlins,rafter etc.including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed

M&L pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.5 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

M&L pre-painted galvalume aluminium zinc coated GI based plain steel sheet 0.5 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

Note for pre-painted coloured Galvalume roofing :-

(i) The manufacturer's test certificate and individual test certificate for the chemical and mechanical properties of sheet must be submitted for approval by the concerned authority prior to installation.

(ii) The contractor shall ensure that no leakages take place from the roof. The roofing shall be Coloured Galvalume roofing system (olive green colour or as approved by GE) with feed material manufactured from 0.50 mm Total coated thickness (TCT), minimum 550 MPa yield strength and shall conform to the physical specifications of IS: 2062 of 2011, coated with hot dip metallic Aluminium / Zinc alloy coating AZ150 as 150 gm/sq.mt total on both sides complete all as specified and as directed.

(iii) The painting shall be coloured baked enamel polyester with silicon coating of film thickness 25 microns nominal on the exposed face/exterior side and on the reverse side ( interior face) shall be white with 15 microns film thickness, over a coat of 5 micron nominal thickness Primer.

(iv) The contractor shall produce purchase vouchers for each lot and independent test for verification of Engineer-in-Charge.

S&F Powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified Note:- minimum thickness of powder coating shall be 50 micron

S&F Powder coated aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified Note:- minimum thickness of powder coating shall be 50 micron

S & F 12 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with aluminum framework complete all as specified

S & F 5mm thick plain sheet glass ordinary quality and glazed with oil putty in square exc 0.5 sqm in each pane complete all as specified and directed.

S & F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified

S & F brass mortice lock 4 lever, 100mm, vertical type for aluminium door complete all as specified

M & L Preparation of new plastered or unplastered surface of walls, and applying three coats of white wash complete complete all as specified and as directed .

Supply, fixing, testing and commisioning of Portable Air dryer chiller (Air cooling unit) of Capacity 100 CFM with Supply air temp : 10 deg celcius, Prefilter-01 No, Final filter -01 No, Digital flow meter - 02 Nos, Flow control valve - 02 Nos, Duct/Hose of 50 mm dia - 5 meters each 2 Nos. Note:- The contractor shall give a written guarantee of minimum 12 months after certified date of completion.

Supply and fix stainless steel pipe 25mm bore ISI marked, Heavy duty, class C, fixed to wall with necessary pipe supports, clamps, brackets and suitable for compressed air supply line of 7 to 8 bar complete all as directed.

Taking down carefully copper/Alu point wiring (light, fan. socket or power) complete including fixtures and fitings such as switches, ceiling roses, pendents, regulators, sockets , light fitting etc and removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separetely) and making good distrubed surfaces of walls, floors etc. complete all as specified and directed.

M & L Point wiring complete with 1.5 sqmm single core PVC insulated, unsheathed FRLS 1100 volts grade,FRLS cable and incl PVC Casing Capping with accessories in wall/roof/ceiling/hangar steel frames etc incl Modular terminal boxes fabricated with 1.6mm MS sheet concealed/fixed surface to walls covered with modular white cover plate with frame etc and 1.5 sqmm PVC insulated, unsheathed copper conductor multistranded cable 1100V grade as earth continuity conductor & connecting to common earth dolly all as specified for the followings:-

One light point/fan/bell point controlled by one switch

All as per item No. 193 here in before but for One 3 pin socket out 5 amp on the same board

All as per item No. 193 here in before but for one switch socket outlet 3 pin 5 Amps on independent board

All as per Sl No 193 above but Wiring with 4 Sqmm copper multistranded unsheathed cable and 4 Sqmm copper cable for earth continuity conductor controlled by one 15A switch socket independently

S&F modular switch 1 way 6 Amps, 1 module complete all as specified and directed..

S&F modular switch 1 way 16 Amps, 1 module complete all as specified and directed..

S&F modular socket outlet multipurpose 2/3 pin 6 amps, 2 module complete all as specified and directed..

S&F modular socket outlet multipurpose 2/3 pin 6/16 amps, 2 module complete all as specified and directed..

S&F Modular Bell push 6A 1 module complete all as specified and directed.

S&F White cover plate with frame, 1 module complete all as specified and directed.

S&F white cover plate with frame, 3 Module complete all as specified and directed.

S&F white cover plate with frame, 6 Module complete all as specified and directed.

S&F white cover plate with frame, 8 Module complete all as specified and directed.

S&F Metal flush box 1/2 module complete all as specified and directed.

S&F metal flush box 3 module complete all as specified and directed.

S&F metal flush box 6 module complete all as specified and directed.

S&F metal flush box 8 module complete all as specified and directed.

S&F Buzzer, Ding Dong AC. 230 volts, single pole complete all as specified and directed.

S&F electronic modular fan regulator 230 volts, step type socket type, hum free 120 watt 2 Module complete all as specified and directed..

S & F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and directed.

S&F ceiling rose, surface type Bakelite 65x55mm 3 terminal complete all as specified and directed.

Supply and fixing in repairs LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing in repairs LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S & F in repairs LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m

Supply and fixing in repairs factory made powder coated distribution board TPN 4 way, double door including bus bar, Neutral bar, standard DIN rail, earth bar acomplete all as specified and directed

Supply and fixing in repairs factory made powder coated distribution board SPN 8 way, double door including bus bar, Neutral bar, standard DIN rail, earth bar acomplete all as specified and directed

S&F in repairs Triple pole Nuetral MCB 63 Amp , 415 v, 50 Hz AC suitable for ‘C’ curve, 10 KA breaking capacity complete conforming to IS 8828 of 1996 all as specified

S&F in repairs MCB SPN 32 Amp , 240 v, 50 Hz AC suitable for ‘C’ curve, 10 KA breaking capacity complete conforming to IS 8828 of 1996 all as specified

Supply and fixing in repairs single pole MCB 6 to 32 Amps, 240 v, 50 Hz AC suitable for ‘C’ curve, 10 KA breaking capacity conforming to IS 8828 of 1996 all as specified

M&L Sub main wiring for circuit complete with 2 runs of 6 sqmm single core PVC insulated, unsheathed FRLS 1100 Volt grade multi stranded copper conductor cable drawn through and including suitable size PVC Casing Capping conduit and accessories complete fixed surface to wall/roof/ceiling etc and including 1 run of 6sqmm single core PVC insulated, unsheathed FRLS 1100v grade multi stranded copper conductor cable as earth continuity conductor etc complete all as specified and directed. Make:- Havells/ Polycab/ Plaza.

Note for item No 226 :- (a) 2 runs of 6 sqmm cable along with one run of 6 sqmm cable for earth conductor and PVC casing capping conduit shall be measured as one length.

(b) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x 6mm thick burried directly in Ground (Earth Pit not less than 2.25 Metre below Ground Level) with Top edge of the Plate not less than 1.50 Metre below Ground Level, connected with Galvanised Earth Strip of size 25mmx4mm by means of Bolts, Nuts, Check Nuts and Washers of GI or Steel and connected Earthing Testing Point/Bus-bar including GI 40mm bore (dia) light grade Protection Pipe, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt, magnesium sulphate (1 : 1 : 0.5) in alternate layers of not exc 150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of size 350x350x50 mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, Funnel with GI Watering Pipe 20mm bore (dia) medium grade including necessary Excavation in in any type of Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing on Completion, complete all as per specified and as directed by Engineer-in-Charge.

Note for Item 229 :- (a) All Joints should be joined by Exothermic Welding or Brazing.

(b) After completion of work earthing shall be tested by the contractor in presence of Engineer-in-Charge, User and proper record shall be maintained.

(c) Earth resistance tester shall be provided by the contractor. It should be caliberated from authorised company/ lab.

(d) After testing if desired earth resistance of less than 5 Ohm is not obtained, the earthing will be redone at no extra cost to Govt till desired result is obtained.

(e) The quoted rate is deemed to be inclusive for GI strip of size 25mmx4mm

Supply and fixing Low Voltage Surge Protector 3 pole and neutral at right side , (50 KA per pole) 50 KA complete all as specified and directed. Make: Legrand Cat No. 412277 or equivalent .

Supply and fixing Low Voltage Surge Protector Single pole and neutral at right side , (25 KA per pole) 25 KA complete all as specified and directed. Make: Legrand Cat No. 412276 or equivalent.

Supply and fixing factory made powder coated distribution board SPN 4 way, single door including bus bar, Neutral bar, standard DIN rail, earth bar complete all as specified and directed

Supply and fixing factory made powder coated distribution board SPN 2 way, single door including bus bar, Neutral bar, standard DIN rail, earth bar complete all as specified and directed

S&F Triple pole and earth encolsure with a three pin and earth plug with socket complete with one triple pole MCB 63 amps, 415 volts complete all as specified and directed .

S&F single pole and earth encolsure with a three pin and earth plug with socket complete with one single pole MCB 20 amps, 230 volts complete all as specified and directed .

M&L Sub main wiring for circuit complete with 4 runs of 6 sqmm single core PVC insulated, unsheathed FRLS 1100 Volt grade multi stranded copper conductor cable drawn through and including suitable size PVC Casing Capping conduit and accessories complete fixed surface to wall/roof/ceiling etc and including 2 runs of 6sqmm single core PVC insulated, unsheathed FRLS 1100v grade multi stranded copper conductor cable as earth continuity conductor etc complete all as specified and directed. Make:- Havells/ Polycab/ Plaza.

Note for item No 241 :- (a) 4 runs of 6 sqmm cable along with 2 runs of 6 sqmm cable for earth conductor and PVC casing capping conduit shall be measured as one length.

(b) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles.

M&L Sub main wiring for circuit complete with 2 runs of 4 sqmm single core PVC insulated, unsheathed FRLS 1100 Volt grade multi stranded copper conductor cable drawn through and including suitable size PVC Casing Capping conduit and accessories complete fixed surface to wall/roof/ceiling etc and including 1 runs of 4sqmm single core PVC insulated, unsheathed FRLS 1100v grade multi stranded copper conductor cable as earth continuity conductor etc complete all as specified and directed. Make:- Havells/ Polycab/ Plaza.

Note for item No 244 :- (a) 2 runs of 4 sqmm cable along with 1 run of 4 sqmm cable for earth conductor and PVC casing capping conduit shall be measured as one length.

(b) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles.

Supply installation, testing & commissioning of maintenance free chemical earthing consisting of copper bounded pre-welded electrode of 10 feet length, 17.2 mm dia made of high tensile low carbon steel rod with 250 micron (average) molecularly bounded copper on the outer surface confirming requirements of UL- 467 with exothermically joint together should be tested on 25 KA fault current with provision for connection clamp of size 150 mm long, 5 mm thickness with 12 mm dia hole of 4 numbers for termination on top of copper bonded rod along with 50 Kg eco friendly Back Fill compound with each earth rod including taking down old unserviceable earthing materials. The Back Fill compound should be tested to achieve 0.02ohms. The Back fill Compound should comply to IEC 62561-7 having passed leaching, corrosion, sulphur and resistivity test as per IEC-62561-7 by NABL accredited Lab, size of bore 6-8 inch, 11 feet depth, distance between each bore shall be 3 mtrs long the above installation shall be completed with 10 liters of Super Charger Earthing liquid tested by any NABL agreated laboratory tested as per IEC-62561-7, read with ASTM G57-06, CI 3.4.A. Make : ISG Global / SafeTrode/ Errico or equivalent

Note For Item No 247:- The unit quoted rate shall deem to be included for the following :- (i) Prior to installation of maintenance free chemical earthing, soil resistivity test to be carried out at the location where earthing work to be done in presence of Engr-in- Charge/JE (E/M),user and the report has to submit to Garrison Engineer with recommendation of manufacturer, if required additional interconnection of earthing (not more than 04 number of earthing) to achive earth result less than 1 Ohms. The arrangement done for soil resistivity testing and submission of report with recommendation deemed to be included in the quoted rate.

(ii) The description/ size/ qty of items mentioned in above are for indicating only however qty/ size may vary at site condition to maintain the earth resistance 1 ohm. The contractor shall quote rate by considering all factors.

(iii) Rate of earth energizer compound of 25 Kg of 02 bags and earth resistance reducing liquid 10 litre per cane for each pit deemed to be included in the quoted rate.

(iv) Resistivity of earth energizer compound and resistance reducing earthing liquid shall be certified by any NABL accredited lab carried out as per IEC-62561-7 read with ASTMG57-06, CI-3.4A and the certificate of same shall be submitted by the contractor before commencement of work.

(v) Earthing shall be tested after completion of work by the contractor in presence of Engr-in-charge, user and proper record shall be maintened duly signed by all concerned. After testing if the desired earth resistance of less than 1 Ohm is not obtained, the earthing will be redone at no extra cost to Govt. till desired result is obtained.

(vi) Earth resistance tester will be provided by the contractor. Tester should be calibrated from authorised company/ lab.

(vii) The contractor shall give a written guarantee of minimum three years for maintaining the earth resistance less than 1 Ohm after certified date of completion.

(viii) No further maintenance or periodic watering or recharge shall be required in earthing during its guarantee period of over 03 years in all type of soil including soft/ disintegrated or hard rock.

(ix) During the guarantee period, if earth resistance is not maintained less than 1 ohm the contractor has to redo or rectify at no extra cost to Govt till desired result is mainained.

(x) A security deposit of value equal to 2.5 % of the rate quoted for chemical earthing per each earthing shall be retained from payment due to the contractor for the guarantee period.

(xi) Earth enhancing material should not leach into the adjacent soil or underground water channels and its PH valve should be in neutral range complete all as specified and as directed. It should solidify when mixed with water and set like concrete.

(xii) The electrode shall carry manufacturer's name .

(xiii) The connection clamp shall be permanentlly welded to the copper bounded rod to avoid any kind of connectivity loss,.The pre-welded copper bounded rod shall not need any additional clamp for termination.

(xiv) Copper strip of size 20 x 3 mm should be fixed on proper post insulator at the instrument end (copper strip shall be measured and paid seperately) .

(xv) The acceptable earth resistance at earth busbar/ test point shall not be more than 0.1 ohm.

(xvi) The contractor shall submit CPRI India certified document for copper bonded rod to ensure genuity of material.

(xvii) Sign board of mild steel 2 mm thick duly painted with two coats of synthetic enamel paint over a coat of red oxide Zinc chrome primer showing result of earthing should be fixed near the earth pit after completion as directed by engr -in- charge.

(xviii) Earth work such as auguring and making good the surrounding area shall carried out in any type of soil.

Supply and fixing of Earth pit cover made of heavy duty poly plastic and earth inspection cover made of high grade polypropylene of size top dia not less than 250 mm, bottom dia not less than 330 mm and height not less than 260 mm dia having load bearing capacity not less than 8 tons for each electrode pit complete all as specified and directed. Make : ISG Global or equivalent make of SafeTrode/ Errico.

Note for Item No 266 :- The contractor shall submit load bearing capacity certificate from the manufacturer.

Supply and fixing copper strip 20 x 3mm thick as earthing lead fixed to wall/roofs etc all as directed.

S&F epoxy base insulators of suitable size 40mm height for fixing copper earth strip on wall/ceiling/floor/poles etc.

p.chinnasamy

S.RAMACHANDRAN

KSR AND COMPANY

T C KARUNANITHI

Neptune Engineers and Builders

Lucky Enterprises

pk janardhanan

KUMAR AGENCIES