Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Infra Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹49.5 LAccepted-AOC | L1 | Accepted-AOC being L1 | |
| 2 | L2₹52.9 L+₹1.1 L (2.13%)Rejected-Finance | L2 | Rejected-Finance NOT BEING L1 | |
| 3 | L3₹55.9 L+₹4.1 L (7.88%)Rejected-Finance | L3 | Rejected-Finance NOT BEING L1 | |
| 4 | L4₹57.8 L+₹6.0 L (11.7%)Rejected-Finance | L4 | Rejected-Finance NOT BEING L1 |
Tender Value
₹45 L
EMD Value
₹90,000
Closing Date
4 Sept 2024, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Major MK Yadav, GE
GE (AF) Kalaikunda PO Kalaikunda Air Field Dist Paschim Medinipore State West Bengal Pin 721303
REPAIRS TO JOINERIES, CUPBOARDS, ALUMINIUM DOORS , WINDOWS AND OTHER CONNECTED WORKS IN DOMESTIC AREA AT AIR FORCE STATION KALAIKUNDA UNDER GE (AF) KALAIKUNDA
2024_MES_664762_1
C/8018/E8
Open Tender
Civil Works
Item Rate
180 days
KALAIKUNDA
Please refer Tender documents.
7 documents required · 7 mandatory
₹500
GE AF KALAIKUNDA
₹90,000
Yes
20 Sept 2024
9 Jul 2024
5 Sept 2024
9 Jul 2024
4 Sept 2024
23 Jul 2024
Amount
Taking down shutters of any description n .exc 1 sq. m each .complete all as specified and directed.
Taking down shutters of any description exc 1 sq. m and not exc 2 sq. m each .complete all as specified and directed.
Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm each complete all as specified and as directed (unit rate shall be inclusive of demolition of cement concrete blocks for embedding hold fasts complete.)
Taking down chowkats of frames wth shutters (without taking out off shutters from the frame) exc 1.5 sqm and n exc 4.00 sqm each including hold fasts and removing the same from site complete all as specified and as directed. (unit rate shall be inclusive of demolition of cement concrete blocks for embedding hold fasts complete.)
Taking down aluminium Chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4.00 sqm each complete all as specified and as directed
Taking down aluminium chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm each complete all as specified and as directed
S & F pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.25 mm thickness, size 105 mm X 60 mm, Profile C, single rebate or more including necessary fixing lugs, hinges(03 Nos of 100 mm size and 01 No of 50 mm size medium weight coled rolled mild steel butt hinges per leaf ) lock strike plate, etc incl one shop coat of priming complete all as specified and directed
S & F pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, size 125 mm X 60 mm, Profile C, single rebate or more including necessary fixing lugs, hinges(03 Nos of 100 mm size and 01 No of 50 mm size medium weight coled rolled mild steel butt hinges per leaf ) lock strike plate, etc incl one shop coat of priming complete all as specified and directed
S & F 35 mm thick, 2nd class hardwood of durability class II as per IS 12896: 1990 factory made, panelled shutters (two panels) with lock rail and panel of 12 mm thick veneered particle board, Grade -I, Type -I (solid core, general purpose), designation (SO GP-I) conforming to IS 3097 supplied and fixed to chowkhats. The size of style and rail as per IS 1003 (Part I) kiln seasoned and chemically pressure treated complete all as specified and as directed.
M & L for 35 mm thick 2nd class hardwood of durability class II as per IS 12896: 1990, factory made, glazed and skeleton shutters, open rebated and prepared to receive glass, wire gauze, etc. (without sash bar), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part-I section 8 Clause 8.24 (a) complete all as specified and as directed by the Engineer-in-Charge.
Supply and Fix, factory made solid panel prelam PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded prelam PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail: Panelling of both sides plain PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, fixed to door frame complete all as specified and directed.
Supply and Fix, solid PVC door frame of size 50 mm X 47 mm made out of 5 mm Prelam PVC sheet reinforced with MS square tube, fixed in opening all as specified and directed.
S & F flush door shutters, 35 mm thick, solid core of block boards with construction, MR grade, commercial type with stiles, rails and lipping of timber as given in Group 2A and Group 2B of Annex B of IS 2202 (Part 1): 1999, both sides face panels of plywood as per IS 710: 2010, covered with decorative face veneer with lipping in both side faces complete all as specified and as directed.
S & F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded including making good disturbed surfaces as per existing specfication complete all as specified and directed.
S & F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded including making good disturbed surfaces as per existing specfication complete all as specified and directed.
Supply and Fix, steel ventilator with top hung shutter including hinges, steel peg stay, complete, dovetailed or welded, including making good disturbed surfaces as per existing specfication complete all as specified and directed.
Materials and Labour for plain cement concrete (1:2:4) type B0 using 12.5 mm graded aggregate in lintels up to 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles throating,and roof padding as directed including necessary from work complete all as specified and directed.
Supply & fix sheet glass, ordinary quality, 4 mm thick and glazed with oil putty or fixed with beads in square not exceeding 0.5 Sqm in each pane complete all as specified and directed.
S & F 4 mm thick figured glass, pin head type and glazing with oil putty or fixed with beads in square not exceeding 0.5 sqm in each pane complete all as specified and as directed.
S & F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed.
S & F 20mm bore PVC coated MS conduit drapery rods, suitable for door/widows curtain with incl necessary fancy type dooms as approved by GE, and fitted to each end, brackets and fixed to wall complete all as specified and directed.
Supply and Fix,4 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sq M in each pane with and including hacking out old broken glass (any thickness, size, quality or description) from frame including providing wooden beads painted with two coat of enamel paint over a coat of primer at any height with safety measures complete all as specified and directed.
S & F 4mm thick figured Sheet glass pin headed type and glazing with oil putty and pins in square n exc 0.5 sq. m in each pane on wooden/steel joinery with and including hacking out old broken glass (any thickness, size, quality or description) from frame including providing wooden beads painted with two coat of enamel paint over a coat of primer at any height with safety measures complete all as specified and directed.
S & F in repair stainless steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed.
S & F bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed
S & F aluminium barrel tower bolts with barrel and bolt of extruded sections of aluminium alloys, 150 mm long, anodized finish not be less than Grade AC 10 of IS 1868 : 1996 with transparent anodic film complete all as specified and as directed.
S & F aluminium barrel tower bolts with barrel and bolt of extruded sections of aluminium alloys, 200 mm long, anodized finish not be less than Grade AC 10 of IS 1868 : 1996 with transparent anodic film complete all as specified and as directed.
S & F aluminium alloy sliding door bolts with hasp, staple and fixing clips of sheets, or extruded sections and fixing bolts and sliding bolts of extruded sections of aluminium alloy, 300 mm long, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed.
S & F aluminium alloy sliding door bolts with hasp, staple and fixing clips of sheets, or extruded sections and fixing bolts and sliding bolts of extruded sections of aluminium alloy, 250 mm long, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed.
S & F 100 mm medium weight mild steel butt hinges made out of cold reduced low carbon steel or hot rolled carbon steel as per IS 1341: 1992 complete all as specified and as directed.
S & F 75 mm medium weight stainless steel butt hinges made out of cold reduced low carbon steel or hot rolled carbon steel as per IS 1341: 1992 complete all as specified and as directed.
S&F 125mm long Parliament hinges, mild steel cold rolled complete all as specified and as directed.
S&F 150mm long mild steel ordinary quality rat rail rod pattern spring including roller plate complete fixed to steel surfaces including necessary welding complete all as specified and directed.
S&F 150mm aluminum extruded aluminium alloy handles (fabricated type) anodised of mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed.
S & F 100mm hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed
S & F plain fillets of 2nd class hard wood in square, rectangular or triangular in section wrought secured with screw, but not exceeding 03 sqcm complete all as specified and directed.
S&F 30mm width of flaps (when open) Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed.
S & F double action concealed type floor springs (hydraulically regulated) made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel top cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and as directed.
S & F exposed type hydraulically regulated door closers, universal closer, bottle type (type A), Designation No. 3, suitable for 61 kg to 80 kg mass of doors & 851 mm to 1000 mm width of door, aluminium alloy non porous body and black plate, aluminium alloy piston or pack piston/ pillion, anodized finish not be less than Grade AC 15 of IS 1868 : 1996 with transparent anodic film as per IS 3564: 1995 complete all as specified and as directed.
S&F in repair 18 mm thick Block boards, grade 2 quality, interior grade, decorative type with decorative face veneer on one face and including 6mm thick teak wood beading around as in cupboard shelves, pelmet boxes etc fixed with screws to timber frame work complete all as specified and as directed.
S&F in repair 18mm thick Block boards, grade 2 quality, interior grade, decorative type with decorative face veneer on one face as as in cupboard shutter, partition fixed with timber/steel frame work complete all as specified and as directed.
Material and Labour for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel and iron surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.
M & L for preparation of new or previously untreated wood or wooden surfaces, of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.
S&F Rolled mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with & including either hooks & hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails & guides) & hanging; also fastening & fixing complete GDE Fe410-0 Quality B complete all as specified and directed by Engineer-in-charge.
S&F Mild steel, plain black sheet 1.00mm thick in wall cladding, steel gates & similar work, cut to size, holes punched; including round headed screws, clout nails or rivets & fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed by Engineer-in-charge.
S & F hot rolled medium and high tensile structural steel of grade E165 as per IS 15911: 2010 as in framed work such as grills, grating, etc., with ends of bars of shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework water tanks and similar work complete all as specified and directed by Engineer-in-charge.
Demolition of brick work or stone/ boulder masonry built in cement mortar or cement lime mortar in existing manholes / septic tank, sumps ,soakage pits including all quoins, arches, pillars etc complete all as specified and as directed.
M&L, brick work with fly ash brick , straight or curved on plan, exc. 6 metre mean radius built in cement mortar 1:4 as in any position complete all as specified and as directed.
Taking down cement or cement lime plaster any description, on brick or stone walls including chhajja of any floor and roof projection etc including raking out joints, hacking for key, scrubbing down with water etc complete.
Materials and Labour for rendering 15 mm thick, cement plaster, in cement mortar (1:6) on surface fair face of brickwork in walls and finishing surface even and smooth without using extra cement, complete all as specified and directed.
Materials and Labour for rendering 5 mm thick, cement plaster, in cement mortar (1:4) mixed with water proofing compound as per manufactures instructions over and including 10mm thick backing coat in cement mortar (1:4) on fair faces of brick work or concrete surface in walls, complete all as specified and directed. Note: - (Water proofing compound will be measured and paid separately)
Supply only liiquid water proofing compound complete all as specified and directed
Material and Labour for applying two coats of cement-based paint, white or tinted to new plastered surfaces on walls including priming with alkali resistant priming paint and including preparation of surfaces complete all as specified and directed.
M&L for preparation of newly plastered surfaces of walls, and applying two coats acrylic distemper on wall ,over and including with a coat of 3 mm thick white wall care putty premium quality over and including a coat of primer new plastered or unplastered surfaces on wall, complete all as specified and as directed.Make;Berger (Bison)/J&N(Jensolin)/Asain Piants(Tractor) /Nerolac (Beauty)
Taking down Aluminium door shutters any size and description and refixing in the same opening including making petty repairs as required like cleaning and repair/replacement of beadings, glazing clips, rubber gasket, stoppers, adjusting tower bolts, locks, hydraulic door closer, hinges etc and make smooth functioning with entire satisfaction of Engr-in-Charge complete all as specified and as directed Note: spare part are required to be replaced deemed to included in quoated rates
Taking down Aluminium window shutters any size and refixing in the same opening including making petty repairs as required like cleaning and repair/replacement of beadings, glazing clips, rubber gasket, stoppers, adjusting tower bolts, locks, hydraulic door closer, hinges etc and make smooth functioning with entire satisfaction of Engr-in-Charge complete all as specified and as directed Note: spare part are required to be replaced deemed to included in quoated rates
S&F Anodised aluminium with powder coating (minimum thickness of powder coating 50 micron) door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.
S & F of Powder coated (minimum thickness of powder coating 50 micron) Aluminium alloy sliding windows with frames 20mm series, 3 track sliding shutters comprising of 3 track bottom frame weighing not less than 1.006 Kg/RM and side & top frame weighing not less than 0.876 kg/RM, top & bottom rails of shutter weighing not less than 0.46 kg/RM, vertical style weighing not less than 0.398kg/RM and interlocking style weighing not less than 0.489kg/RM, duly fitted with neoprene/EPDM gasket, beading, glazing clips ect. two shutters tinted glass panes 4.80 mm nominal thickness and one shutter with stainless steel wire cloth 0.36mm dia and average width of aperture 1.4mm , aluminium alloy handles etc. complete with and including aluminium deco grill medium grade of mesh size 75mmx75mm with 6mm square anodised aluminium bars fixed with aluminium frame of size 37x19x2mm all as specified complete in all respect area exc 0.90 sqm. but n. exc 1.50 sqm.
S & F aluminium sections for doors, windows, ventilators, door partition including fabrication of frame shutters and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc. including all accessories such as glazings clips, and rubber beadings for fixing glass panes in frame complete all as specified. Note : (i) Glass panes & handle will be measured & paid separately . (ii)The quoted rate shall be inclusive of cost of rubber beading however it will be not be weighed and not paid separately. (iii) All other minor details including cost of locking arrangement shall be included in the quoted rate.
Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin- charge.
S&F Anodised aluminium Power Coated window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws
S&F of second class hard wood for small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours, articles n.exc 200 cucm each complete all as specified & as directed.
M & L Securing glass of any description in existing wooden/steel frames glazed with putty/ beads including removing loose or decayed putty/ beads, painting/oiling one coat on rebates, grooves, reputtying and painting/oiling puttied surface to match existing work complete all as specified & as directed.
S&F in Repair 150mm Floor door stopper of Brass body and tongue, anodised, with hard drawn steel spring, fixed in floor as per specified and directed
S&F in Repair 100mm Size Brass Mortice lock, vertical type,4 lever as per specified and directed
M&L For French polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats, previously polished
S&F Multicolor Fiber Sheet 2mm Thickness high density for Gate and window fitted by screws or pasting as per specified and directed
Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and disposing the rubbish to the out side of MD land
M&L for Non skid coloured ceramic tiles7to 8 mm thick(square/Rectanglar) area of each tiles exc .11 Sqm but not exc 0.18 Sqm, conforming to IS 15622, Grade B II, in floor including 15mm thick screed bed or bedding layer for laying floor finishes in CM 1:6 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match.
M&L for coloured glazed ceramic tiles 350x250 x7mm/450x350xx7 mm thick, conforming to IS 15622, Grade B III but as on vertical surfaces such as skirting/dado including 10mm thick rendering in CM 1:4 .complete all as specified
S&F in repairs 40mm wide and 5mm thick PVC door seal (snake guard) with powder coated aluminium frame.
Resecuring or easing & adjusting without taking down shutter of any description of wooden joinery complete all specified for the following areas:-
Area Not exceeding 1 Sqm each
Area Exceeding 1 Sqm n.exc 2 Sqm each
Area Exceeding 2 Sqm each
Refixing of shutters of any descriptionin in same opening including taking down, easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc. (Renewal of builder's hardware articles, if specially ordered, shall be paid for at 'supplied only' rates under respective items of BOQ Srl Item No 74.00) for the following areas:-
Area Not exceeding 1 Sqm each
Area Exceeding 1 Sqm n.exc 2 Sqm each
Area Exceeding 2 Sqm each
Supply only the following builders hardware (to be incorporated only against BOQ Srl No 73.00):-
150 mm long Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed
150 mm long Aluminium anozied barrel tower bolt of extruded section
250mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate.
250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy
100mm long Butt hinges, medium weight, cold rolled mild steel fixed with screw
100mm long Butt hinges, medium weight, cold rolled mild steel fixed with welding
75mm long Butt hinges, medium weight, cold rolled mild steel.
M&L for Glazing with sheet glass 4.8 mm thick ordinary quality in panels of aluminium windows, ventilator, door etc. fixed with glazing clips, rubber beading and EDPM gasket in square not exceeding 0.5 Sqm in each pane.
INDIA TRADE ENGINEERING (BID ID -3080500)
SHARMA ENTERPRISES (BID ID -3080537)
M/s Antara (BID ID -3082524)
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .