SPL REPAIR TO BLDG NO SB 4BY1 TO 4BY5 OR MD ACCN AT NALWA LINE COMMA SPL REPAIR TO BLDG NO 2C CARRIAPPA ENCLAVE AND PROVN OF CATTLE TRAP AT MAIN GATE OF NGFA COLONY UNDER GE WEST LUCKNOW

Amount

Demolition of brick work or stone/ boulder masonary, built in cement mortar or cement lime mortar including all quions, arches, pillars, etc. but excluding ashlar facings, dressed stone work and precast concrete articles etc. complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc. 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended works complete all as specified and directed. NOTE: Reinforcement shall be cut as required to facilitate demolition.

Excavating over areas, n.exc 1.5m deep and getting out in soft/ loose soil complete all as specified and directed.

Excavating in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/ loose soil complete all as specified and directed.

Returning, filling in, trenches including spreading, levelling, watering and well ramming in layers not exc. 25cm in soft/ loose soil complete all as specified and directed.

Removing surplus excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

M&L cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and directed.

M&L for brick work with old size fly ash bricks of class designation 75, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with old size fly ash bricks of class designation 75, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

M&L for cement concrete 1:2:4 type B-2 (using 40 mm graded stone aggregate) as in walls or retaining walls, any thickness, size or shape including pilasters, buttresses, columns, pillars, boundary pillars and posts (including caps and bases) complete all as specified and directed.

M&L Cement Concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other bands, plinth courses, string cources, lacing cources, parapets and railing upto 60cm in hight, copings, kneelers, apex stones, bed plates, water troughs, hold fasts and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

M&L Mild Steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L Mild Steel TMT bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L RCC 1:2:4 type B-1 using 20mm graded stone aggregate as in slab supported on wall, beams and coloumns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and similar works complete all as specified and directed.

Use and waste of formwork to soffits of suspended slab such as roof slabs, floor slabs, landing and similar work not exceeding 200mm thick (horizontal or sloping) for rough finished surfaces complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area n. exc 1.50 Sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exc 1.50 Sqm but n. exc 4sqm each complete all as specified and directed.

S&F pressed steel door frame of size 105x60mm with one or more rebates, made out of 1.25mm thick MS sheets including necessary fixing lugs, hinges, lock strike plate, etc. complete as specified and fixed including one shop coat of primer complete all as specified and directed.

S&F pressed steel door frame of size 125x60mm with one or more rebates, made out of 1.25mm thick MS sheets including necessary fixing lugs, hinges, lock strike plate, etc. complete as specified and fixed including one shop coat of primer complete all as specified and directed.

M&L cement concrete 1:3:6 type C-0 using 12.50mm graded stone aggregate as in filling and mass concrete to back of pressed steel frame complete all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc, (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut or mitred beads for securing glass, gauge etc sizes of members of shutters as specified in SSR Part-I Section 8 clause 8.24(a) and fitted to chowkats complete all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc, divided into squares, with plain, chamfered or rounded, metred and rebated shash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut or mitred beads for securing glass, gauge etc sizes of members of shutters as specified in SSR Part-I Section 8 clause 8.24(a) and fitted to chowkats complete all as specified and directed.

S&F 35mm thick 2nd class hard wood, factory made, plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial venneering on both faces, the size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated and fixed to chowkats complete all as specified and directed.

S&F flush shutters 30 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 28mm thick factory made solid PVC flush door shutter with frame (kitchen cabinet), uPVC, made from co-extruded three layer rigid foam sheet (single extruded process) with 0.8 to 1mm thick outer face layer having density not less than 1400 Kg/Cum and density of central core material not less than 600 Kg/Cum, manufactured by an ISO 9001:2015 certified company and fixing in frame at site as per specifications and drawing complete all as specified and directed.

S&F Solid PVC frame (single rebated) size 60mmx30mm made out of solid PVC foam with homogeneous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100x8 sheet metal CSK screws complete all as specified and as shown on drawing. NOTE: Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life.

S&F 28mm thick factory made solid PVC profiled panel door shutter with integral skin as frame & 3mm thick high pressure compact laminate on both sides of approved colour as infill, with ‘C’ type GI or 40x20x19mm of MS pipe as stiffner and fixed in frame at site as per specifications and drawing complete all as specified and directed.

S&F 100mm size butt hinges, medium weight, cold rolled, mild steel and fixed with screws complete all as specified and directed.

S&F 150mm size extruded aluminum alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 200mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

M&L in repair 18/19mm thick block boards, grade 2 quality, interior grade, commercial type fixed with screw/nails to timber frame work as in pelmet boxes/ cup boards and cabinets etc including 6mm thick teak wood lipping alround complete all as specified and directed.

M&L 0.90mm thick Decorative laminates type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.

S&F Continuous (piano) hinges, mild steel, bright finished or electro galvanised, with width of flap 30mm when open, and fixed with screws complete all as specified and directed.

S&F 100mm long aluminum anodised, hasp and staple, safety type, with mild steel hinge pin including bolts to hinge plate and fixed with screws complete all as specified and directed.

S&F in repair 300mm long, mild steel, ordinary rat tail rod pattern springs including including roller and roller plate complete all as specified and directed.

S&F Ball catches (magnet catcher) with 8mm dia steel ball, brass body and striking plate including letting in, overall size 50x15mm and fixed to shutter complete all as specified and directed.

S&F in repair floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm complete all as specified and directed.

M&L for 3mm thick sheet glass, ordinary quality and glazing with oil putty or wooden beads in square, area n.exc 0.5 Sqm in each pane complete all as specified and directed.

M&L for 4mm thick sheet glass, ordinary quality and glazing with oil putty or wooden beads in square, area n.exc 0.5 Sqm in each pane complete all as specified and directed.

M&L for 3mm thick figured glass, pin head type and glazing with oil putty or wooden beads in square, area n.exc 0.5 Sqm in each pane complete all as specified and directed.

M&L for 4mm thick figured glass, pin head type and glazing with oil putty or wooden beads in square, area n.exc 0.5 Sqm in each pane complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed

S&F Box type steel windows/ventilators with side hung shutters with glazed and gauzed double panel shutters both provisions including box type hinges or factory made butt hinges with steel handle, tower bolts, hold fasts and steel peg stays etc. complete with glazing bars dovetailed or welded and 10mm square guard bars @ 125mm c/c complete as per CELZ drg No. LZ/C-TD/130 sheet No 1/4 to 4/4 complete all as specified and directed.

S&F casement windows with net and grill, multi shutters, made out of uPVC multi cavity frames of section size 60x60x2.5mm, double shutter division with mullions section size 50x64x2.5mm and shutter made of 50x85x2.5mm duly reinforced and welded in corners with EPDM gasket provn for glass and mosquito mess shutters made out of uPVC section of size 61x27x2mm with 1.2mm thick GI chanel and fitted properly including all necessary fittings hinges, MS grill of 12mm round bars duly powder coated finished and fixed complete all as specified and directed.

Dismantling of Asbestos cement (corrugated, semicorrugated etc.) sheets in roof coverings complete all as specified and directed.

S&F multi-rib TM profile, tensile strength 550 Mpa, colour coated 0.50mm thick pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet, having maximum pitch of 250mm c/c and minimum 30mm crest depth in length as per site requirement, the feed material manufactured out of 0.50mm (TCT) with coating of 18-20 microns top coat over 5 microns primer and 8-10mm alkaline back of zinc aluminium alloy of AZ-150, including the sheet shall have a hot dip metallic zinc aluminium alloy coating of zinc 43.5%, aluminium 55% and silicon 1.5% with total mass coating of 150 gms/sqm on both sides having covered width 1020mm and return leg for proper side lap as in roof covering/ cladding and fixed with self tapping screws with EDPM seal complete all as specified and directed.

M&L mild steel framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintel hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290, Gde E-165 complete all as specified and directed.

M&L structural steel work with rolled mild steel sections as in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) and similar articles conforming to Fe-290 Gde E-165 complete all as specified and directed.

Taking down cement or cement lime plaster any description from walls/ceiling etc including racking out joints, hacking for key & scrubbing down with water all as specified and directed.

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces of wall and finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 with integral water proofing compound @ 3% by weight of cement on fair faces of brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed. NOTE: WPC shall be measured and paid seperately under respective item.

M&L for rendering 5mm thick in CM 1:3 on fair faces of brick work or concrete surface of ceiling and finished surface even and smooth without using extra cement complete all as specified and directed.

Supply only integral waterproofing compound complete all as specified and directed.

M&L for two coats of oil bound distemper over one coat of primer and 1mm thick layer of wall care putty on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

Complete removal of existing treatment of wall and M&L for two coats of oil bound distemper on previously treated plastered surfaces of wall over one coat of primer and 1mm thick layer of wall care putty including preparation of surfaces complete all as specified and directed.

M&L for two coats of cement base paint over one coat of primer on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

Complete removal of existing treatment of wall and M&L for two coats of cement base paint over one coat of primer on previously treated plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for three coats of white wash on newly plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed.

M&L for two coats of white wash on old decorated plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood or wood based materials of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel or iron of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old or previously treated surfaces of wood or wood based materials of any description over 10cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old or previously treated surfaces of steel or iron of any description over 10cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old or previously treated surfaces of steel or iron of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for 40mm thick cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in floor, finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection, laid in panels, finished surface even and smooth without using extra cement and forming 12mm wide expansion joints to the full depth, and filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade 'A' complete all as specified and directed.

M&L Roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for joint free glazed ceramic tiles, coloured, superior quality of size 350x250x7mm/ 450x350x7mm thick, in vertical surfaces etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for joint free non skid ceramic tiles, coloured, superior quality, 7 to 8mm thick, (square/ rectangular), area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

S&F vitrified tiles, double charged, coloured, superior quality 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

S&F vitrified tiles, double charged, coloured, superior quality 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in vertical surfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

M&L 18-20 mm thick granite stone slab, machine cut and polished as in shelves, cooking platform etc., bedded and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust with admixture of pigment to match the shade of granite stone, laid over and including 20mm thick screed bed in cement mortar 1:4, including rubbing, rubbing, grinding, making hole for gas pipe line and including making sandwitch moulding to edges complete all as specified and directed.

Cutting chases, pinning in, for concealed water tubing etc. in brick walls and making good to disturbed surface in cement mortar 1:3, cutting not exceeding 10cm in girth complete all as specified and directed.

Taking up or down 15mm bore pipes steel tubing and connections including cleaning for refixing or removing to store or removing from site complete all as specified and directed.

Taking up or down 20mm bore pipes steel tubing and connections including cleaning for refixing or removing to store or removing from site complete all as specified and directed.

S&F 15mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floors complete all as specified and directed.

S&F 20mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floors complete all as specified and directed.

Dismantling of water tanks of capacity exc. 250 litres and not exc. 500 litres of any type and in any position and removing from site complete all as specified and directed.

Dismantling of water tanks of capacity exc. 500 litres and not exc. 1000 litres of any type and in any position and removing from site complete all as specified and directed.

S&F 500 litres capacity rotational molded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position complete all as specified in SSR Part-I and directed.

S&F 1000 litres capacity rotational molded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position complete all as specified in SSR Part-I and directed.

S&F ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe or brass ferrule and fixed suitable for 20mm bore pipe (Min weight 210gms) complete all as specified and directed.

S&F in repair 15mm bore Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repair 20mm bore Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repair Vitreous China wash down water closet pan, pedestal pattern, white, with 'P' or 'S' trap, excluding flushing cistern and flush pipe, including connection to drain pipe (or outgoing pipe) and to flushing pipe etc. and making good to floor complete all as specified and directed.

S&F in repair plastic water closet seat cover, white, closed pattern with flat bottom and cover, fixed with MS chromium plated hinging device ISI marked as approved, complete all as specified and directed.

S&F in repair Vitreous China squatting pan, 'Orissa pattern', size 580x440mm, white, with integral foot rests including PVC 'P' or 'S' trap, excluding flushing cistern and flush pipe, including connection to trap and flushing pipe etc. and making good to floor complete all as specified and directed.

S&F in repair PVC valveless, syphonic action type, low level, flushing cistern of 10 lit capacity, white, with inlet, ball valve, float valve and handle including bracket, rubber cone and flush pipe etc. and connection to pipes complete all as specified and directed.

S&F in repair vitreous china Wash basin, white, flat back type of size 550x400mm including CP waste coupling and 32mm dia waste pipe and fixing of 02 nos brackets made out of 40x40x5mm MS angle iron etc. complete all as specified and directed.

S&F in repair bib taps 15mm bore, half/quarter turn, fancy type, long body, cast copper alloy, chromium plated, screwed for iron pipe or for brass ferrule including all accessories complete all as specified and directed.

S&F in repair angle valves 15mm bore, fancy type, cast copper alloy, chromium plated with long shank and cup screwed down, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair Pillar taps 15mm bore, half/quarter turn, fancy type, long body, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe including all accessories complete all as specified and directed.

S&F in repair stop valves concealed type 15mm bore, fancy type, cast copper alloy, chromium plated with long shank and cup screwed down, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair 15mm bore PVC connections, superior quality, with CP brass nuts of length 450mm complete all as specified and directed.

S&F in repair central hole basin mixer, fancy type, brass chromium plated, with round spout with popup waste system, including plugging and fixed, suitable for 15mm bore pipe complete all as specified and directed.

S&F in repair wall mixer with telephonic shower arrangement, connectings legs and wall flanges, fancy type, brass chromium plated, with costed swinging spout including plugging and securing to walls suitable for 15mm bore pipe complete all as specified and directed.

S&F in repair brass chromium plated overhead shower rose with arms, 125mm size, round shape, single flow, fancy type, suitable for 15mm bore pipe and fixed complete all as specified and directed.

S&F in repair hand shower (health faucet), superior quality, round shape, single flow, brass chromium plated, with 1m long chrom finish flexible pipe with wall hook bracket etc. and all fittings for EWC complete all as specified and directed.

S&F in repair toilet paper holder, superior quality, fancy type, brass chromium plated with wall hook bracket complete all as specified and directed.

S&F in repair CP brass tubular towel rail 20mm dia, 'D' type, 600mm long between flanges, superior quality, fancy type, fixed to wall with PVC gully and CP brass screws complete all as specified and directed.

S&F in repair 5.5mm thick sheet glass shelf assembly, fancy type, sheet glass shelf of size 600mm long and 120mm wide with CP bracket guard and railing, fixed to wall with PVC gully and CP brass screws complete all as specified and directed.

S&F in repair 5.5mm thick sheet glass corner shelf assembly, fancy type, sheet glass shelf of size 250x250mm, with CP bracket guard and railing, fixed to wall with PVC gully and CP brass screws complete all as specified and directed.

S&F in repair peg set of 6, brass chromium plated, fancy type, with 40mm wide brass CP strip, fixed to wall with wooden plug/ PVC gully with CP screws and cup washers complete all as specified and directed.

S&F in repair 25mm dia mild steel PVC coated curtain rod, superior quality, any colour, with end brackets and end knobs and fixed to wall with wooden plug/ PVC gully with CP screws and cup washers complete all as specified and directed.

S&F in reapir kitchen sink with drainage board made of stainless steel 1mm thick with plugs, washers, waste coupling and waste pipe, including bedding in cement mortar 1:3 to dwarf wall or fixing cantilever brackets and connecting union to waste pipe, overall size 915mmx460mm with bowl size 410x330x160mm complete all as specified and directed.

S&F in repair kitchen sink without drainage board made of stainless steel 1mm thick with plugs, washers, waste coupling and waste pipe, including bedding in cement mortar 1:3 to dwarf wall or fixing cantilever brackets and connecting union to waste pipe, overall size 495mmx420mm with bowl size 410x330x160mm complete all as specified and directed.

S&F in reapir stainless steel kitchen plate rack (utensil rack) of size 750x600x250mm, made out of 0.8mm thick stainless steel sheet, approved design and fixed to wall with brass screws and PVC gully including all necessary fittings like nuts and bolts etc complete all as specified and directed.

Demolition and breaking up 100/75mm internal dia of drain pipes (Salt glazed ware, AC or Reinforced concrete), set in cement mortar complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls with PVC clamp complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls with PVC clamp complete all as specified and directed.

S&F PVC (SWR) bends of any radius, suitable for 110mm bore PVC pipes, fixed and jointed with solvent complete all as specified and directed.

S&F PVC (SWR) bends of any radius, suitable for 75mm bore PVC pipes, fixed and jointed with solvent complete all as specified and directed.

S&F PVC (SWR) bends of any radius with oval acess door, suitable for 75mm bore PVC pipes, fixed and jointed with solvent complete all as specified and directed.

S&F in repair PVC (SWR) multi floor trap (nahnai trap) with PVC grating including jointing with solvent cement, suitable for 110mm bore PVC pipes complete all as specified and directed.

S&F in repair PVC (SWR) multi floor trap (nahnai trap) with PVC grating including jointing with solvent cement, suitable for 75mm bore PVC pipes complete all as specified and directed.

S&F in repair PVC (SWR) vent cowls suitable for 110mm bore pipes complete all as specified and directed.

S&F in repair grating round 100 mm dia of PTMT (minimum weight 25gms) complete all as specified and directed.

S&F in repair grating round 125 mm dia with waste hole of PTMT (minimum weight 40gms) complete all as specified and directed.

S&F in repair 40mm bore low density polyethylene (LDPE) pipes of pressure rating 6 Kgf/sqcm complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

M&L for PCC 1:3:6 type C-0 using 12.5mm graded stone aggregate as in padding over roof slab, roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

M&L for provn of roof treatment with polymeric water proofing membrane all as given below:- (a) Taking down existing water proofing treatment and cleaning roof surface by washing and rubbing etc. and removing the material retrieved to a distance not exceeding 500m where directed. (b) M&L plastering 10mm thick in CM 1:4 using 100% coarse sand on roof including WPC 3% by weight of cement. (c) Applying a coat of bituminous primer conforming to IS: 3384-1986 @ 0.25 Iit/sqm on prepared surface and allowed to dry. (d) Applying and laying 3mm thick APP membrane having non woven polyester matt at core and covered with high quality polymeric asphaltic protected thermo fusible HMHDPE film on both sides with over laps 10cm and 15 cm at longitudinal and transverse direction respectively and sealed by flame, sealing all overlaps complete including treatment at all junctions and corners. The membrane shall be torched into groove on vertical plane and groove sealed with cement mortar 1:3. (e) M&L for applying two coats of aluminium paint on membrane @ 0.10 Kg/Sqm (each coat) complete all as specified and directed.

M&L for provn of roof treatment with polymeric water proofing membrane all as given below:- (a) Taking down existing water proofing treatment and cleaning roof surface by washing and rubbing etc. and removing the material retrieved to a distance not exceeding 500m where directed. (b) Applying a coat of bituminous primer conforming to IS: 3384-1986 @ 0.25 Iit/sqm on prepared surface and allowed to dry. (c) Applying and laying 3mm thick APP membrane having non woven polyester matt at core and covered with high quality polymeric asphaltic protected thermo fusible HMHDPE film on both sides with over laps 10cm and 15 cm at longitudinal and transverse direction respectively and sealed by flame, sealing all overlaps complete including treatment at all junctions and corners. The membrane shall be torched into groove on vertical plane and groove sealed with cement mortar 1:3. (d) M&L for machine pressed cement concrete tiles of size 250x250mm and 20-22mm thick, set jointed and pointed in neat cement slurry as in floors/ terraces over and including 15mm thick screed bed in cm 1:4 complete all as specified and directed.

All as per item No 131 above but except concrete tiles. NOTE: Old brick tiles retrieved from demolition shall be used.

M&L for post construction ATT of soil by providing and injecting chemical emulsion along the external wall below concrete or masonary apron using chemical emulsion @ 2.25 litre per linear metre including drilling and plugging holes in apron with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed.

M&L for post construction ATT of soil by providing and injecting chemical emulsion under existing floors, using emulsion @ one litre per litre per hole, at 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed.

Taking down copper/ aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors etc. to match the existing complete all as specified and directed. NOTE: Credit for this items shall be made as per conditions separately.

Taking down carefully main switches, DB's, MCB DB's of any way or rating and making good the disturbed surfaces of walls complete all as specified and directed.

M&L for point wiring complete for one light point or one fan point controlled by one, one way 5 Amp switch with PVC (FRLS) insulated unsheathed multistranded copper conductor of size 1.50 sqmm nominal cross sectional area single core drawn in and including 20mm dia 'medium grade' PVC concealed conduits ISI marked and fittings, including pressed steel concealed terminal switch boxes not less than 1.6mm thick of reqd size factory made duly painted inside and outside with one coat red oxide primer, 3mm thick plastic laminated bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers complete including 1.50 sqmm nominal cross sectional area PVC(FRLS) insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories complete all as specified and directed.

All as per item no 137 above but for one 5 pin 5 Amp socket outlet point on an independent board.

All as per item no 137 above but for one 5 pin 5 Amp socket outlet point on the same board with other switch.

All as per item No. 137 above but for One bell/ buzzer point on an independent board controlled by one bell push

All as per item no 137 above but for one 6 pin 15/16 amps socket outlet point on an independent board with cables of size 2.50sqmm and green colour earth cable of size 2.50sqmm.

S&F Switch piano, flush type, single pole, one way 5/6 Amp 230 Volts complete all as specified and directed.

S&F Switch piano, flush type, single pole, one way 15/16 Amp 230 Volts complete all as specified and directed.

S&F socket outlet, flush type, single pole, multipurpose 2 in 1, 5 pin 5/6 Amp, 230 volts complete all as specified and directed.

S&F socket outlet, flush type, single pole, multipurpose 2 in 1, 5 pin 15/16 Amp, 230 volts complete all as specified and directed.

S&F ceiling rose, 3 terminal, PVC/ Polycarbonate, insulated body, surface bakelite sheet 63.50mm dia complete all as specified and directed.

S&F Lamp holder PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F bell push, flush type, single pole, one way 5/6 Amp, 230 volt flush type complete all as specified and directed.

S&F call bell, ding dong type, AC single pole, 230 volt complete all as specified and directed.

S&F in repair sheet metal enclosure for MCB DB double door type, tripple pole and neutral 4 way, 415Volts with 200 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed.

S&F in repair sheet metal enclosure for MCB DB double door type, single pole and neutral 8 way, 240Volts with 200 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed.

S&F sheet metal enclosure for MCB DB single door type, single pole and neutral 2 way, 240Volts with 200 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed.

S&F in repair MCB, single pole 6 to 32 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

S&F in repair MCB, single pole & neutral 40 to 63 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

S&F in repair MCB, tripple pole & neutral 63 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

S&F sheet metal enclosures, single pole with socket plug top and MCBs with a two pin and earth plug and socket complete with one single pole MCB 20 Amps complete all as specified and directed.

S&F ceiling fan regulator, electronic, rotary step up socket type, 230 volts suitable for 1200/1400 mm sweep ceiling fan including necessary connection complete all as specified and directed.

Taking down old copper/ aluminium sub main wiring or service connection complete all as specified and directed

S&F sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 4sqmm nominal cross sectional area and one run of 4sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 25mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings complete all as specified and directed. NOTE:- One unit length shall measured as two run of main wire and one run of conduit & earth wire.

S&F sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 6sqmm nominal cross sectional area and one run of 6sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 25mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings complete all as specified and directed. NOTE:- One unit length shall measured as two run of main wire and one run of conduit & earth wire.

S&F in repair wall mounted 18/20 W LED integrated tube light fitting of size 1200mm long batten with aluminium housing and decorative end cap and one no 18/20 W LED 6000 K, 230V, with integrated electronic driver complete with all required fittings and fixtures arrangement including and provn of connection from ceiling rose to luminaries with suitable size copper wire complete all as specified and directed. Make: Havells cat no. LHEXBXPNIN1W020 or Surya Visco Cat no. SLEBT 20 IL or C&S Nakshatra cat no. LTTB4F20WLED/W

S&F LED bulk head light fitting, made of cast aluminium body with heat resistance pressure, die cast housing, IP-65 protection cover and one no. 7 W LED, 6000K, including and provn of connection from ceiling rose to luminaries with suitable size copper wire complete all as specified and directed. Make: Philips VISTAGLOW cat no. WT140W LED 7S CW PSU S1 PC or equivalent in Havells or C&S or Bajaj.

S&F in repair wall mounted, 9/10 W LED mirror light fittings of size 600mm long with integrated Batten and LED 9/10 W, 6000 K, 230V with polycarbonate housing & integrated electronic driver including and provn of connection from ceiling rose to luminaries with suitable size copper wire complete all as specified and directed. Make: Havells cat no. LHEXBXP7PN1W009 or Surya Visco cat no. SLE BT 10 or C&S cat no. LTDC01210WLED/WD.

S&F in repair security light fitting of 25 W LED 6000 K, with high power LED source (more than 100 lumens per watt), PDC housing, IP65 with 4KV inbuilt surge protection driver and one no. 25W LED tube, with all accessories, prewired with and fixed to bldg/pole including GI bracket 1.20m long bent to shape, made out of 40mm dia GI light grade pipe with nuts, bolts and washers and provn of connection from ceiling rose to luminaries with suitable size copper wire complete all as specified and directed. Make: Havells cat no. LHEWEBP7PL6S025 or Surya Lexon cat no. SLE UL25W IP 66(LXN) or C&S INDUS cat no. LTESS25WLED/LS.

M&L Earthing complete with galvanised steel earth plate electrode 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m deep below normal ground level, connected to galvanised earth lead wire 4.0mm dia (7.50m) by means of bolts, nuts, check nuts & washers of galvanised iron or steel, earth lead wire protected by 15mm dia GI pipe light grade, 20mm dia light grade GI pipe for watering, meshed funnel, alternate layer of charcoal and common salt complete all as SSR Item No. 19471 and shown in electrical plate No. 3 of SSR part-I with PCC chamber, 50mm thick RCC cover in 1:2:4 type B-1 using 20mm graded stone aggregate reinforced with 8mm dia TMT bar @ 80mm c/c both way in lieu of CI pit cover and protection including necessary excavation and earth work complete all as specified and directed.

Taking down carefully ceiling fan/ exhaust fan by disconnecting all electrical connection, proper cleaning and refixing the same including all electric connections with twin core flexible copper wire 23/0.0076 size after necessary repair work complete all as specified and directed.

Taking down carefully electric meter of any capacity from wall or any position by disconnecting all connection and refixing the same including all electric connection and acessories as required including teak wood board of suitable size complete all as specified and directed.

S&F in repair 1100V grade heavy duty XLPE armoured cable, PVC insulated aluminium conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connection of size 6sqmm, 2 core cable complete all as specified and as directed

S&F in repair integrated LED Post top lantern with high power 25/30 W LED as light source, energy saving, envioronmental friendly, long life asethetically designed with symmetrical light distribution, spun auminium landscape lumainaire incl LED driver complete and incl neceesary electrical connection complete all as specified and as directed. Make: C&S cat no. LTGLC30W4PLED/W or Wipro cat no. LP07-431-XXX-57-CL or Bajaj cat no. BJCPT1218CLEAR

S&F modular switch, single pole, 1 way 5/6 Amp, 230 Volts, 1 module complete all as specified and directed. Make: MK/ Legrand/ ABB/ Crabtree.

S&F modular switch, single pole, 1 way 15/16 Amp, 230 Volts, 1 module complete all as specified and directed. Make: MK/ Legrand/ ABB/ Crabtree

S&F modular bell push, single pole, 1 way 5/6 Amp, 230 Volts, 1 module complete all as specified and directed. Make: MK/ Legrand/ ABB/ Crabtree

S&F modular socket, single pole, 5 pin 5/6 Amp, 230 Volts, combined 2 module complete all as specified and directed. Make: MK/ Legrand/ ABB/ Crabtree

S&F modular socket, single pole, 5 pin 15/16 Amp, 230 Volts, combined 2 module complete all as specified and directed. Make: MK/ Legrand/ ABB/ Crabtree

S&F modular rotary step type fan regulator, single pole, 120W, 2 module, complete all as specified and directed. Make: MK/ Legrand/ ABB/ Crabtree

S&F modular white cover plate with frame, 3 module, complete all as specified and directed. Make: MK/ Legrand/ ABB/ Crabtree.

S&F modular white cover plate with frame, 4 module, complete all as specified and directed. Make: MK/ Legrand/ ABB/ Crabtree

S&F modular white cover plate with frame, 6 module, complete all as specified and directed. Make: MK/ Legrand/ ABB/ Crabtree

S&F modular white cover plate with frame, 8 module, complete all as specified and directed. Make: MK/ Legrand/ ABB/ Crabtree

S&F in repair decorative wall light fittings made out of polycarbonate, (Spiral B-22 base) with 01 No. 9 W LED Bulb, 230 V, 6000K, complete including required fixing arrangements complete all as specified and directed. Make: Havells cat no. CITY 1 LHDL02160099 or equivalent in Bajaj/ Philips/ C&S.

GANGA TRADERS

M/S Reliance Construction

M/s Sudhir Enterprises

sidhi vinayak construction

QUALITY CONSTRUCTIONS CO

M/S Chandra Mohan and Sons