PROVISION OF WASHING ROOM, WATER STORAGE TANK WITH BATHROOM URINAL INCLUDING PLINTH PROTECTION WITH ELECTRIC WIRING, PROVN OF WAITING SHED NEAR HOSPITAL MAIN GATE FOR COVID VACCINATION AND PROVISION OF RECEPTION COUNTER AT MAIN GATE

Amount

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in soft/loose soil, complete all as specified and as directed.

Surface dressing n exc 15 cm deep, in soft/loose soil, complete all as specified and as directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out, in soft/loose soil, complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, laying UG cable, pipes etc. and getting out, in soft/loose soil, complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. in soft/loose soil, complete all as specified and as directed.

M&L Site development with approved earth to be obtained from outside MOD land and filling including raising (or lowering) soft/loose earth, spreading in layers not exc. 30cm thick, watering, ramming/rolling with power roller (8 to 10 Tonne) and finishing to required size, shape, etc, to any heigth from original ground level complete all as specified and as directed. NOTE: - (i) Payment shall be done on the basis of compacted thickness as defined in MES SSR 2020 (Part II) Clause No 3.6. (ii) All cost of procurement of earth including cost of transporation, royalities, taxes etc shall be deem to be included in the Unit Rate Quoted. (iii) Quoted rates are inclusive of necessary surface dressing including removing of surplus soil as directed

Removing excavated material, soils, n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and directed.

M&L for PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.

M&L Brickwork with sub class ‘B’ bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:6 for finished even and smooth without using extra cement complete all as specified and as directed.

M&L Hardcore with broken stone of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M&L for 40mm thick Cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as sub base complete all as specified and as directed.

M&L 75mm thick Cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as floor, finished even and smooth using extra cement complete all as specified and as directed.

M&L 75mm thick cement concrete (1:3:6) type C-2( using 40mm graded crushed stone aggregate) as in plinth protection laid in alternate bays (not exceeding 2 Sqm each) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and as directed.

M&L 38mm Glass dividing strips, 3 mm thick inserted in position, complete all as specified and as directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete including necessary preperation of surfaces and applying one shop coat of red oxide, zinc chrome primer all as specified and as directed.

S&F Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.., conforming to Fe.290.Gde-E-165 ncluding necessary preperation of surfaces and applying one shop coat of red oxide, zinc chrome primer complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description not exc 10cm in width or girth not otherwise described applying two coats of synthetic enamel paint complete all as specified and as directed.

S&F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

M&L preparing newly plastered surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L for Brickwork with sub class B bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 including provision of 2 Nos 8mm dia TMT bars at every fourth course complete all as specified and as directed.

M&L for TMT bar 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for TMT bar 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for Reinforced cement concrete (nominal mix) in 1:1½:3 type A1 (using 20 mm graded stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m spancomplete all as specified and directed.

M&L Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc., finished fair complete all as specified and directed.

M&L 25mm thick damp proof course to horizontal surfaces In cement concrete 1:2:4, type B-0(1:2) including necessary form work, complete all as specified and directed.

M&L Bitumen blown any grade, applied hot, two coats, to concrete surfaces at the rate of 1.5kg. per sq. m per coat complete all as specified and directed.

M&L Hardcore with broken stone of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and directed.

M&L 150mm thick Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate as sub base of floor, complete all as specified and as directed.

M&L prepartion of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

Excavating over areas, n exc 1.5 m deep and getting out in soft/loose soil, complete all as specified and as directed.

M&L 15mm thick rendering with cement mortar (1:4) on fair faces of brick work in two layers (10mm & 5mm) seperately mixed with water proofing compound in top layer as per manufacturer's instructions and finishing the surface even and fair without using extra cement complete all as specified and as directed. Note:- WPC shall be measured and paid seperately under appropiate item.

Supply only liquid water proofing compound complete all as specified and as directed.

M&L for Rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:6 for finished even and fair, without using extra cement complete all as specified and as directed.

M&L for prepartion of newly plastered surfaces of walls and applying two coats of oil bound distemper over 2mm thick of wall care putty and a coat of primer including necessary preperation of surfaces complete all as specified and directed.

M&L for preparing new Plastered surfaces of walls, Chajja/Fasia etc surfaces and applying two coats of weather proof Acrylic Exterior emulsion paint of approved make and shade over 2mm thick of wall care putty and a coat of Acrylic emulsion primer complete all as specified and directed.

M&L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L 75mm thick Cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as sub base of floor, hardstanding etc complete all as specified and as directed.

M&L Non skid coloured tiles 7 to 8 mm thick(square/ rectangular) area of each tiles exc.11 sqm but not exc 0.18 sqm in floor etc set and jointed in neat cement slury over and including 15 mm thick cement screed bed in cement mortar 1:6 complete all as specified and as directed.

M&L for coloured Glazed ceramic tiles 300mm x 450mm x 7mm (Square/rectangular)as in vertical surfaces set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick cement screed bed in cement mortar 1:4 complete all as specified and as directed.

M&L Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm but n exc 10cm long and dia of neck 11 to 15mm complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing as specified in SSR Part II Section 8 omplete all as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as specification & drawing as specified in SSR Part II Section 8 complete all as directed.

S&F Aluminium anodised barrel tower bolt of extruded section and fixed 125 mm size complete all as specified and as directed.

S&F 250 mm aluminium alloy sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium ally fixed complete all as specified and as directed.

S&F 100 mm size Butt hinges, medium weight, cold rolled mild steel and fixed complete all as specified and as directed.

S&F 100 mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

S&F 15mm bore GI pipe medium grade water tube with all fittings laid in floors fixed to walls and ceilings or laid in floors complete all as specified and as directed.

S&F 20mm bore GI pipe medium grade water tube with all fittings laid in floors fixed to walls and ceilings or laid in floors complete all as specified and as directed.

S&F Vitreous China, pedestal pattern white (excluding fixing bolts, flushing cistern and flush pipe) including Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device including 10 ltrs capacity low level valve less PVC syphonic action type flushing cistern white with in let ball valve float and handle, PVC flush pipe and 15mm bore PVC Connection with PTMT nut of length 600 mm complete all as specified and as directed.

S&F bib tap 15mm bore fancy type chromium plated Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; complete all as specified and as directed.

S&F Vitreous China wash basin, white, flat back of size 580x 450 mm (flat back or angle back type), including cutting for and pinning in ends of brackets or erecting stand, including 01 Nos PVC waste pipe 25mm dia., 75cm long with 32mm dia connector, 01 Nos, 15mm bore pillar taps, cast copper alloy with capston heads, chromium plated, fancy type, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe and 01 Nos,15mm bore PVC Connection with PTMT nut of length 600 mm complete all as specified and as directed.

S&F waste fittings 32 mm bore, brass, chromium plated for Sink, wash basins etc with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed complete all as specified and as directed.

S&F 32mm bore of discharge pipe, Waste coupling of PTMT (half or full threaded) . (Minimum weight 32mm- 45gms) complete all as specified and as directed.

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and as directed.

S&F Vitreous china urinal partition white of size 310x700 mm complete all as specified and as directed.

S&F brass chromium plated shower rose of 125mm size with or without swivel joint with or without swivel joints, including fixing to steel pipe or union complete all as specified and as directed.

S&F 15mm bore stop valves fancy type cast copper alloy, chromium plated Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed all complete as specified and as directed.

S&F 15mm bore stop valves fancy type cast copper alloy, chromium plated with long shank and cup (concealed type), screwed both ends including necessary fittings such as sockets for pipe or for union all complete as specified and as directed.

S&F 20mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F 15mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S & F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed.

S&F 110mm dia PVC (SWR) bends of any radius complete all as specified and as directed.

S&F 110mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and as directed.

S&F 110mm PVC (SWR) vent cowl complete all as specified and as directed.

S&F 75mm dia of outlet, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F 20mm dia brass chromimum plated, Tubular towel rail, D type, 60cm long between flanges complete all as specified and as directed.

M&L false ceiling with 10 mm thick 600mm x900mm plaster of Paris sheets fixed with machine screws on and including GI channel 18 gauge thick grid work, main joists placed at 750 mm centre to centre , cross joists placed at 450mm centre to centre, hanging with 6mm dia GI wire suspenders from roof, ‘J’ hooks bolts and nuts etc and treating the POP sheets with thin layer of POP with Gypsum anhydrous binder and prepare the surface till smooth surface is achieved; and applying two coats of plastic emulsion paint over a coat of primer matching with the colour of ceiling sheets all complete as required as per manufacturer’s instructions and as directed .

S&F Rotational moulded polyethylene water storage tank (Cylindrical vertical with closed top) (confoirming to IS 12701-1996) multi layer hoisted and fixed in position 500 ltrs capacity complete all as specified in SSR Part I complete all as specified and as directed

S&F 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 210gms) complete all as specified and as directed

M&L Rolled mild steel in Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. conforming to Fe 290 (Gde E 165) complete all as specified and as directed

M&L for PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in mass concrete complete all as specified and as directed.

M&L Reinforced cement concrete (nominal mix) in 1:1½:3 type A1 (using 20 mm graded stone aggregate) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), roughed finished complete all as specified and as directed.

S&F Powder coated (minimum thickness of powder coating 50 micron) Anodised aluminium frame for windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed Note:- Design/pattern, profile sizes and other dimensions shall be of standard sizes and as directed

S&F Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium windows/ventilators any type including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, along with standard locking arrangements, handles, tower bolts etc as required. complete all as specified and directed Note:- (i) Labour charges for fixing of glass/wire guage/aluminum grills is inclusive in the unit rate quoted. Glass/Wire Guage/aluminum grills shall be measured and paid seperately at supply only rates (ii) Design/pattern, profile sizes and other dimensions shall be of standard sizes and as directed

Supply only 4mm thick plain sheet glass, ordinary quality fixed with Aluminum frame work n. exc 0.5 sqm in each pane complete all as specified and as directed.

M&L 150mm cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in complete all as specified and as directed.

M&L for 150mm bore Salt glazed stoneware drain pipes laid in trenches and jointed in cement mortar(1:1) complete all as specified and as directed.

M&L for concealed point wiring for light points controlled by one, one way switch complete with 1.5 Sqmm single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with multistranded copper conductor with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 Sqmm PVC insulated multistranded unsheated copper conductor cable FR-LS (ISI markd) with proper colour coding as earth continuity conductor connected to common earth dolly , modular sheet steel sunken terminal box of appropriate size suitable for modular switch/ fittings concealed in walls, with modular back plate, top cover fixed flush to wall for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications, complete all as specified and as directed. Note:- Connections of cable with MCB's or bus bar shall be done through proper size copper/brass thimbles.

M&L for concealed point wiring for one socket outlet 16 amp on independent board complete with 4 Sqmm single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with multistranded copper conductor with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 2.5 Sqmm PVC insulated multistranded unsheated copper conductor cable FR-LS (ISI markd) with proper colour coding as earth continuity conductor connected to common earth dolly , modular sheet steel sunken terminal box of appropriate size suitable for modular switch/ fittings concealed in walls, with modular back plate, top cover fixed flush to wall for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications, complete all as specified and as directed. Note:- Connections of cable with MCB's or bus bar shall be done through proper size copper/brass thimbles.

S&F Modular type switch piano white 10 Amps single pole one way 01 module complete all as specified.

S&F Modular type switch piano white 16/20 Amps single pole one way 01 module complete all as specified and as directed.

S&F of Modular shuttered Socket outlet 6 Pin, 16/20 Amp, 2 Module, 230 volts, (ISI marked) complete all as specified and as directed.

S & F Surface and wall mounted LED batten 10 watt (or nearest next higher wattage) 2feet long with Aluminum housing & integrated Electronic Driver with IP20, PF 0.90, total System Lumens 1050 Lumens, 6500k CRI ≥ 80, Operating Voltage range 140 V - 270 V complete all as specified and as directed.

S&F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings/ pendent fitting including 7watt (or nearest next higher wattage) LED lamp complete all as specified and as directed.

S&F of exhaust fan metal body with louvers 300 mm sweep, 1320 RPM or more, Air Delivery not less than 1600 CMH, single phase, 240 Volts, AC, 50 Hz and connecting up complete and provision of cable 3 core of size 0.75 Sqmm from ceiling rose to fan complete all as specified and as directed.

S & F energy saving & environment friendly long life 60 Watt,(or nearest next higher wattage) CT ≥ 5700 K, LED building security light made up of pressure die-cast aluminium housing with acrylic cover as diffuser with IP 66 protection & impact resistance not less than IK-07 complete with integrated type, with high efficiency electronic driver, surge suppressor of 5 KV or more & high brightness LEDs, luminaire efficacy > 110 lumens/Watt, power factor ≥ 0.90, operating range 140 to 270 V, 50 Hz complete and connecting up with and including three core twisted flexible copper conductor cable of suitable size all as specified & as directed.

S&F Sheet metal enclosure for 4 way Distribution Boards (DB’s), double door, Single pole & neutral with 200 Amps rated bus bar, IP-43 protection, complete including. blanking plates as required & flush to wall/other surface complete all as specified and as directed. .

S&F MCB, SPN, C Series 240 Volts, 32 Amps 50 HZ, 10KA complete all as specified and as directed.

S&F MCB, SP, C Series 240 Volts, 6-32 Amps 50 HZ, 10KA complete all as specified and as directed.

M&L for 40mm bore GI pipe light grade with all necessary fittings (ISI marked) as in cable protection fixed to pole,laid in trenches/road/floor complete all as specified and as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sqmm 4 core complete all as specified and as directed.

M&L for sand cushioning in cable trenches over & under the cable, with river washed coarse sand, as per standard practice with proper compaction complete all as specified and directed.

Supply and laying for brick protection for protection of cable over sand cushioning cables inside the trench by using common brunt clay building bricks sub-class “B” old size brick and flat and width wise along the axis of the trench complete all as specified and directed.

Material and labour for earthing with GI earth plate electrode 600x600x6mm thick buried directly in ground vertically to depth not less than 2.25m below the ground level with top edge of earth plate at a depth not less than 1.5m below the ground level connected to galvanized iron wire 4mm dia earth lead by means of bolts & nuts,check nuts & washers made of galvanised steel, earth wire protected by and including PCC (1:2:4) type B1 precast RCC cover slab (M-15)reinforced with 8mm dia TMT bars 100mm center to center bothways including one handle made of 10 mm dia round bar, including necessary excavation and earthwork in any type of soil, 20 mm dia medium grade galvanized steel tube for watering with one end fixed with cast iron funnel and wire mesh, 15 mm bore medium grade galvanized steel tubing for drawing earth wire GI strip protection & common salt, charcoal in alternate layers etc. complete all as shown in EP No 3 of SSR Part 1 and testing on completion complete all as specified and as directed.

M&L for surface point wiring for light points controlled by one, one way switch complete with 1.5 Sqmm single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with multistranded copper conductor with proper colour coding drawn through and including non-metallic rigid PVC casing capping medium grade with accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 Sqmm PVC insulated multistranded unsheated copper conductor cable FR-LS (ISI markd) with proper colour coding as earth continuity conductor connected to common earth dolly , modular sheet steel sunken terminal box of appropriate size suitable for modular switch/ fittings concealed in walls, with modular back plate, top cover fixed flush to wall for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications, complete all as specified and as directed. Note:- Connections of cable with MCB's or bus bar shall be done through proper size copper/brass thimbles.

All as per item No 100 here-in-before but for one 6 amps socket out let point on the same board with other switches

All as per item No 100 here-in-before but for one 6 amps socket out let point on independent board.

S&F Modular type switch piano white 6 Amps single pole one way 01 module complete all as specified.

S&F Modular type Socket outlet white 6 Amps 5 pin 2 module for independent board complete all as specified and as directed.

S&F ceiling rose, 3 phase PVC/ polycarbonate, insulated body, three terminals, complete all as specified and as directed.

S&F LED luminarie tube light fitting basic all purpose surface/wall mounted 4 feet LED batton with polycarbonate housing & integrated electronic driver, with high efficient LEDs 20 watt, (or nearest next higher wattage) with all accessories, suitable for operation on Ac, single phase 220 / 230 Volts, 50 Hz supply, complete all as specified and as directed.

S&F, IP 20, class I, LED light 1X20 Watt (or nearest next higher wattage) (4feet), 5700K, wall/ surface mounted, integrated type with aluminium housing and decorative and caps with integrated high efficiency electronic driver and surge suppressor of 2KV or more, luminaire efficiency > 95 lumens/watt, power factor > 0.90, operating range - 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/ square blocks, screws etc complete with all accessories internally prewired and connecting up with complete all as specified and as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sqmm 2 core complete all as specified and as directed.

S&F Sheet metal enclosure for 8 way Distribution Boards (DB’s), double door, Single pole & neutral with 200 Amps rated bus bar, IP-43 protection, complete including. blanking plates as required & flush to wall/other surface complete all as specified and as directed.

Supply, install, testing & commissioning of ceiling fan 1200 mm sweep, Air Delivery not less than 210 CMM, heavy duty, single phase, AC, 230 Volts, 50Hz, 5 star rating, ISI marked complete with 30 cm down rod, canopy, blades, motor etc and connecting up complete including provision of cable 3 core of size 0.75 Sqmm from ceiling rose to fan complete all as specified & as directed.

S&F Modular type white step type regulator, 100Watt, 02 Module for energy saving complete all as specified.

SHANKAR ENTERPRISE

M/S C.M.V CONSTRUCTIONS

M/S SEWAK SINGH