Special Repair to Building No. T-04 (1-9) (09 Accn) Under GE (South) Bangalore

Amount

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises, complete all as directed.

40 mm thick PCC 1:2:4 type B1 using 20 mm stone aggregate as in sub base of floor and mass concrete complete all as directed.

Non Skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed in cement mortar (1:6) complete all as directed.

Non Skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in skirting / dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 10 mm thick screed bed in cement mortar (1:4) complete all as directed.

Non Skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed in cement mortar (1:6) complete all as directed.

Glazed coloured cermaic tiles 300 x 200 x 7 mm thick as in vertical surfaces of walls, set and jointed in neat cement slurry and pointed in coloured cement to match, over and including 10 mm thick rendering in cement mortar 1:4 complete all as directed.

Hacking old brocken glass of any description from wooden or steel frame glazed with putty or wooden beads complete all as directed.

3 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beading in square / rectangular pane n.exc 0.50 sqm in each pane complete all as directed.

Demolition of brick work or stone / boulder masonary, built in cement mortar including all quoins, pillars etc. but excluding ashler facing, dressed stone work or precast concrete articles complete all as directed.

Precast cement block masonry with solid blocks grade C-5, exceeding 10 Cm in width and setting in cement mortar 1:4 complete all as directed.

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key scrubbing down with water etc. complete all as directed.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even and smooth without using extra cement complete all as directed.

Racking out cement mortor Joints / pointing to block in course masonary or concrete block walling complete all as directed.

Drapery rod of high strength aluminium rod powder coated (Coating Minimum 40 micron) of outer dia 28mm and inner dia 24.5mm with 2 nos brackets(projected type/wall to wall),finials and rings (8 rings per Meter) complete all as directed. Make: Sleek line type-II of Mac or Soffio-II of Vista Levolor or equivalent of MAC-Decor/Deco window/Jayesh metal corpn.

Preparation of old wooden surfaces of any description not otherwise described over 100 mm width or girth and applying one coats of synthetic enamel paint complete all as directed.

Preparing new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer over 2 mm thick coat of wall care putty on plastered surfaces complete all as directed.

Complete removal of existing treatment on plastered and other surfaces and applying two coat of oil bound distemper including priming over 2 mm thick wall care putty complete all as directed.

Preparing new plastered wall surfaces, applying two coats of cement base paint over a coat of primer complete all as directed.

Preparation of newly plastered wall surface and applying three coats of white wash complete all as directed.

Preparation of Old plastered wall surface and applying two coats of white wash complete all as directed.

18 mm thick Veneered decorative plywood, type-I, conforming to IS-1328-1996 (with BWR resin) with decorative face veeners on one side and another side commercial ply fixed with screws to timber frame work complete all as directed.

Extra over rates of black board or veneered particle board for external teak wood lipping, 6mm thick, fixed with nails complete all as directed.

Preparation of new plywood surface and applying two coat of synthetic enamel paint over a coat of pink primer complete over 100 mm width or girth complete all as directed.

30 mm wide continuous (piano) higes, mild steel, bright finish or electrogalvanised complete all as directed.

Soft closing kitchen cabinet hinges, stainless steel (Grade 304) complete all as directed Make:- Cat part No. 5120 of Prayag or equivalent of Ozone / Godrej / Hitachi / Dorma

MS 40 mm dia, cupboard knobs fixed with nut, screw and washer of brass polished bright finished complete all as directed

Magnetic catch for drawer of suitable size complete all as directed Make:- Prayag / Ozone / Godrej / Hitachi / Dorma

Stainless steel plate rack of size 31 x 36 x 10 inch complete all as directed Make:- Cat Part No. P-348 of Prayag or equivalent of Shakti / Maharaja.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm and N. exc. 4 Sq.m each complete all as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) n. exc 1.5 sqm each complete all as directed.

Second class hard wood in Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as directed.

Plain framed panelled shutter 35 mm thick of 2 nd class hardwood (any number of panels), with panel of timber flat on both sides (feathered edge) or of veneered particle board medium density, commercial face veneers include for one shop coat of priming confirming to IS 1003 (Part-1) 2003 complete all as directed.

30 mm thick of 2 nd class hardwood glazed and skeleton shutterts open rebated and prepared to receive glass, gauge etc divided into sqaure with plain chamfered or rounded mitred and retreated sash bars any numbers edge of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members as specified in , as specified in SSR Part-I section-8, clause No. 8.24 (a) complete all as directed.

All as per item No. 33 above but SSR Part-I clause No. 8.24 (b)

Preparation of new wooden surfaces of any description not otherwise described over 100 mm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as directed.

Solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet, reinforced with MS square tube and fixing in position with hold fast, complete all as directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing shown in SSR 2010 Part -II complete all as directed.

Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4 mm fixed with stainless steel wire staples complete all as directed.

Butt hinges medium weight cold rolled mild steel fixed of size 100 mm complete all as directed.

All as per item No. 39 but 75 mm.

100 mm long Aluminium anodised barrel tower bolts of extruded section complete all as directed.

All as per item No. 41 but 200 mm long.

Aluminium alloy, anodised, sliding door bolts 300 mm long with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed. Complete all as directed.

Extruded aluminium alloy handles, fabricated type anodised 125 mm long complete all as directed.

All as per item No. 44 but 75 mm long.

Spring, 300 mm long, rat tail rod pattern, including roller and roller plate complete all as directed.

Taking up or down steel tubing and connections, 15 mm bore including cleaning for refixing or removal to store complete all as directed.

All as per item No. 47 but 20 mm bore

15 mm bore, steel water tubing, medium grade, galvanised with all fittings fixed to wall or laid in trenches, complete all as directed.

All as per item No. 49 but 20 mm bore

Vitreous China wash down water closet pan (Pedestal patern) white incuding fixing bolts, excluding flushing cistern and flush pipe complete all as directed.

Plastic cover for the EWC seat, white or black, closet pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as directed.

Viterous china squating pan Orissa pattern WC of size 580 x 440 mm white with integral foot rest with 'P' or 'S' trap fixed in repair with cast iron and stoneware fitting including provn of lime concrete / cement concrete bedding complete all as directed.

Soap dish fancy type cast copper alloy type chromium plated, fixed ‘in repair’ complete all as directed.

PVC flushing cistern low level of 10 liter capacity white with inlet ball valve float and handle including bracket. PVC connections 15 mm size with PTMT nut of length 450 mm complete all as directed.

Health faucet with 1.5 M flexible Chromium plated tube and hook fixed to angle valve fixed in repair etc. complete all as directed. Make:- Cera / Pryag / Jaguar / Hindware / Kohlar

Vitreous china wash hand basin, fixed in repair, white flat back of size 550 x 400 mm including, CI brackets, 40 mm CP brass waste fitting, complete all as directed.

PVC waste pipe with coupling, heavy duty, 32 mm dia for wash hand basin etc. fixed in repair complete all as directed.

PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as directed.

15 mm bore, Stop valves fancy type chromium plated with long shank and cup (conceled type) cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union, fixed in repair complete all as directed. Make:- Ruby series of Cera or equivalent to Kohlar / Jaquar

15 mm bore,stop angle cock fancy type chromium plated cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union fixed in repair complete all as directed. Make:- Ruby series of Cera or equivalent to Kohlar / Jaquar

Bib tap, 15 mm bore, Fancy type, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, fixed in repair complete all as directed. Make:- Ruby series of Cera or equivalent to Kohlar / Jaquar

Pillar tap, 15 mm bore, cast copper alloy, fancy type with capstan heads, chromium plated screwed down high pressure with or without lattered 'Hot' or 'Cold' with long screwed for iron pipe fixed in repair complete all as directed. Make:- Ruby series of Cera or equivalent to Kohlar / Jaquar

Shower rose 125 mm dia, brass chromium plated, with swivel type joint including fixing in repair to steel pipes or union complete all as directed.

Towel rail chromium plated, fixed in repair with chromium plated brass screws and plastic cleats (included) complete all as directed. Make:- Cat part No. BA-20 of Prayag or equivalent of Hindware / Jaquar

Towel ring of CP fixed with and including chromium plated brass screws and wooden/ plastic cleats complete all as directed. Make: Prayag Cat Part No BA-11 or equivalent of Hindware / Jaquar

Glass self outer support of CP frame and ring fixed with and including chromium plated brass screws and sooden/ plastic cleats complete all as directed. Make : Prayag Cat Part No BEA-47 or equivalent of Hindware / Jaquar

20 mm thick, Granite (any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as directed.

Figured glass / pin head type and glazing with oil putty / wooden beading, in squares n exc 0.50 Sqm in each pane 4 mm thick complete all as directed.

Dismantling PVC / CI / AC drain pipe complete all as directed.

75 mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches or in floor etc. complete all as directed.

75 mm bore PVC Floor trap with grating including jointing to waster pipe and embedded in concrete complete all as directed.

110 mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches or in floor etc. complete all as directed.

110 mm bore, PVC (SWR) branch pieces, single Y equal or unequal with access door complete all as directed.

PVC (SWR) reducer, 110 mm bore, complete all as directed.

PVC (SWR) vent cowl 75 mm bore complete all as directed.

Ball valve, 20 mm bore, PTMT, high pressure, with epoxy coated aluminium rod, polythene float and fly nut, screwed for iron pipe or brass ferrule complete all as directed.

Dismantling water tanks of capacity 500 to 1000 liter and removing to store complete all as directed.

Rotational moulded HDPE water storge tank of capacityy 1000 Ltr (cylindrical vertical with closed top) hoisted and fixed in position including connection nipple confirming to IS 12701-1996 complete all as directed.

Ball valve, 20 mm bore, brass body, high pressure, with polythene float and fly nut, screwed for iron pipe or brass ferrule complete all as directed.

Demolition of stone slab and tiles of any description fixed with cement mortar complete all as directed.

Demolition of cement concrete (unreinforced ) in floors and pavings n. exc. 150 mm thickness below or above ground level complete all as directed.

Hard core of broken stone or boulders of gauge n.exc 63mm deposited spread and leveled in layer n.exc 15cm thick, watered and rammed to a true surface complete all as directed

PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in 75 mm thick plinth protection / path / paving finished even and smooth without using extra cement including forming groove 10 mm wide, 30 mm deep, filled with mastic filler complete all as directed.

75 mm thick, plain cement concrete 1:4:8, type D-2, using 40 mm graded crushed stone aggregate as in sub base of floor complete all as directed.

40 mm thick cement concrete type B1 1:2:4 using 20 mm graded crushed stone aggregate as in flooring and finishing surfaces of concrete surfaces even and smooth without using extra cement complete all as directed.

75mm thick cement concrete type B1 1:2:4 (using 20mm graded crushed stone aggregate), as in fllors including spike rolling to surfaces or making impressions of expanded metal whilst the concrete green complete all as directed

12 mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, grade 'A' for 100 mm thick concrete slab complete all as directed

Forming contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade A complete all as directed

Form work to soffits of suspended slab such as roof slab, floor slab etc. complete all as directed.

PCC 1:4:8 type D-2 using 40 mm stone aggregate as in Foundation filling and mass concrete complete all as directed.

Dismantling mangalore pattern roofing tiles with ceiling tiles or slate roofing and similar work complete all as directed

Dismanteling unframed timber filets rails posts rafters purlins etc under 40 sqcm in section in any position complete all as directed

Dismanteling of Asbestos cement (plain / corrugated/ semi corrugated) sheets in roof covering complete all as directed

Prepainted galvalume Aluminium zinc coating corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall fixed with self taping screws or 'L' type or 'J' type or cranked hook bolt, complete all as directed.

Prepainted galvalume Aluminium zinc coating plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall fixed with self taping screws or 'L' type or 'J' type or cranked hook bolt, complete all as directed.

Mild steel rolled section of grade Fe 410 (Gde E-250) quality A as in main and cross beams hip and jack rafters; purlins where connected to common rafter and running rails and similar works fixed with and including angle cleats or other connecting plates complete all as directed.

Excavation in post holes (for similar holes) each n.exc 0.5 cum getting out returning filling in and ramming earth or broken rubbed mixed with earth around in layers not exceeding 25 cm watering and removing surplus soil to a distance n.exc 50m and making good surface in soft / loose soil complete all as directed.

Cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) in wall or retaining wall any thickness, size, shape including pilasters buttresses columns, pillars boundary pillars and posts (including caps and bases) complete all as directed.

Steel work in tubular trusses including special shaped washer etc. complete using ERW or including butt welded tubes conforming to IS 1161-1998 grade St-240 complete all as directed.

Rolled mild steel joist channel angle or tee sections fixed independently without connection plates etc (cut to ordinary lengths i.e within 20mm of the length indicated) conforming to Fe 410 W (Gde E-250) quality A complete all as directed.

Preparation of new steel or iron surfaces of any description over 100 mm width or girth and applying two coat of synthetic enemal paint of approved tint over a coat of red oxide primer complete all as directed.

Post ATT at the points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 liter per holes, by drilling 6 mm dia holes at a down ward angle of 45 degree at 150 mm centre to centre and repluging them with cement mortor (1:2) to match the existing floors complete all as directed.

Post conrtruction ATT of soil under existing floors using emulsion @ 1 litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 to match the existing floors surfaces complete all as directed.

Post construction anti termite treatment (ATT) along external wall below concrete or masonry apron using chemical emulsion at the rate of 2.25 litres per meter including drilling and pluging holes etc. complete all as directed.

Preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with Creosote Oil complete all as directed

Chequered cement concrete tiles of size 200 x 200 x 25 mm thick (with grey cement and no pigments) set, jointed and pointed in neat cement slurry in floor, laid over and including 15mm thick cement screed base in CM 1:4 laid and jointed with grey cement slurry complete all as directed.

Demolition and breaking up drain pipe 150 mm bore any type set in cement mortor complete all as directed.

Excavation in trenches n.exc 1.5 M wide and n.exc 1.5 M depth for foundation or cable trench or for shafts, wells, cesspits, manholes pier holes etc. n.exc. 10 Sqm on plan and n.exc. 1.5 M in depth and getting out in hard / dense soil complete all as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers, not exceeding 250 mm thick, each layer, complete all as directed.

Removing excavated material to a distance exceeding 250 M and not exceeding 500 M and depositing where directed at a level not exceeding 1.5 M above the staring point complete all as directed.

Extra for forming fair finished drain or channel 300 mm inner girth in cement concrete using extra cement including forms moulds, mitered / stopped ends etc. complete all as directed.

All as per Item No. 113 above but 450 mm inner girth

Salt glazed stone ware drain pipe, 150 mm Internal dia grade ‘A’ laid in trenches, jointed and tested, complete all as directed.

Cutting into existing manhole for connecting into new drain, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section), in cement concrete 1:2:4, type B-1, smooth finished and reforming benching as required for 150 mm bore SGSW pipe, complete all as directed.

Proving cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in copings, complete all as directed.

Concrete bed 1:4:8 type D-2 to 150mm drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D-2 complete all as directed

Demolition of cement concrete (Reinforced) in manhole cover not exceedign 15cm thickness (below or above ground floor) complete all as directed

Providing precast RCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) in cover slabs (for manholes etc) complete all as directed.

TMT bars, 10 dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooping ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as directed.

PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in surface channels and foundation of drains complete all as directed.

Removing excavated material exceeding 1.50 Km and not exceeding 5 Km and depositing where directed at a level not exceeding 1.5 M above the staring point complete all as directed.

Removing excavated material exceeding 50 M but not exceeding 250 M and depositing where directed at a level not exceeding 1.5 M above the staring point complete all as directed.

Surface excavation n.exc. 300 mm deep and averaging 150 mm deep and getting out in hard / dense soil complete all as directed.

Providing cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggrtegate) in roof karb or mud stops, rounded or chamfered complete all as directed.

False ceiling with GI snap frame work of size 600 x 600 mm in true horizontal level suspended on interlocking metal grid of hot dipped galvanized steel sections (galvanized @ 170 gsm / Sqm and bottom exposed width prefinished with baked polyester paint) consisting of main `T’ runners of size 38 x 24 x 0.3 mm with suitably spaced joints to get required length spaced at 1200 mm C/C and cross T of size 24 x 25 x 0.3 mm, 1200 mm long spaced between main T at 600 mm C/C to form a grid of 1200 x 600 mm and secondary cross `T’ of length 600 mm and size 24 x 25 x 0.3 mm to be interlocked at middle of the 1200 x 600 mm panel to form grids of 600 x 600 mm and wall angle of size 21 x 21 x 0.3 mm

and laying flase ceiling tiles of 4 mm thick fibre, cement building board, non asbestos (minimum weight 4.8 kg / m2) fixed or laid / inserted to GI frame work with screws / clips for false ceiling work including, wherever required, cutting / making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. main T runners shall be suspended from ceiling using GI slotted cleats of size 25 x 35 x 1.6 mm fixed to ceiling with 6 mm dia and 50 mm long metal dash fastener, 4 mm GI rods with galvanized steel leveling clips spaced at 1200 mm C/C along main `T’ section (False ceiling system shall be capable to bear distributed load of minimum 15 Kg / Sqm) complete all as directed

Taking down copper / aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials for taking credit (credit for above items should be made as per conditions seperately) and making good distrubed surfaces of wall, floors, etc. complete all as directed.

Taking down unserviciable main switch DB, teak wood boards etc. removing materials for taking credit (credit for above items should be made as per conditions seperately) and making good distrubed surfaces of wall, floors, etc. complete all as directed.

Wiring complete with 1.5 Sqmm single core FRLS PVC insulated unsheathed cable 1100 volts grade multi stranded with copper conforming to IS 694 drawn through and including non metalic rigid PVC conduit including accessories, concealed type, MS terminal boxes fabricated with 1.6 mm thick MS sheet fixed in wall concealed type with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch sockets outlets, fan regulators etc including provision of 1.5 Sqmm FRLS PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly for one light or fan point controlled by one way switch complete all as directed.

All as per Item No. 130 above but for bell point

All as per Item No. 130 above but One 3 pin socket point 5 Amp on same board with other switches.

All as per Item No. 130 above but One 3 pin socket outlet, 5 amps, on independent board.

All as per item No. 130 but wire size 2.5 sqmm for 6 pin 15 Amps switch socket combination outlet on independent board.

Ceilling rose surface bakelite 65 x 50 mm three terminals including PVC square blocks complete all as directed.

Switch piano, flush type single pole, 5 Amps one way complete all as directed.

Socket outlet flush type 5 Amp 2/3 pin universal multipurpose complete all as directed.

Switch socket combination flush type 5 Amp 2/3 pin universal multipurpose complete all as directed.

Switch socket combination flush type 5 / 15 Amp two in one 3 pin complete all as directed.

Step type electronic fan regulator, 230 volts, flush type suitable for 1200 mm sweep fan, fixing on board and making necessary electrical connection complete all as directed.

Push type, Bell Piano Switch 6 A one way complete all as directed.

Call Bell, 230 Volt Single Phase complete all as directed.

MCB single pole 6 to 32 Amps 240 volts 10 KA rupturing capacity (curve-c) providing in DB complete all as directed.

All as per item No. 143 but SPN

MCB TPN, 63 Amps, 415 Volts (C curve) providing in DB complete all as directed.

Sheet metal enclosure (ISI marked) distribution board SPN, 415 volts, 8 way horizontal type, double door with 200 Amps rated copper bus bar for housing MCBs, fixed flush in wall surface, and tested complete all as directed.

MCB, DB Double door type, made out of CRCA mild steel sheet surface mounting, TPN 4 way with 200 Amps rated bus bar, 415 volts IP-43, with PVC MCB blanking plates, stove enamelled, dust and vermin proof suitable for incorporation of MCB's and isolators etc. complete all as directed.

Sub main wiring concealed type with 3 runs of 6 sqmm, single core, PVC insulated and unsheathed cable conforming to IS-694, FRLS, 1100 volts with copper conductor multi stranded drawn in non metallic PVC conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied complete all as directed. Note:- Three run of 6 Sqmm cable, one run of of PVC non metalic conduit with all necessary accessories will be measured as one length.

LED batten suitable for indoor application 20W 4 feet length sleek and seamless profiled extruded aluminium/ polycarbonate batten with efficient diffuser and integral electronic driver including two point surface mounting on wall/ ceiling and connecting up with twin core twisted flexible copper conductor cable of suitable size including taking down existing unserviceable tube light fittings complete all as directed. Make:- Wipro Cat part No LL20-221-XXX-65NE3 or equivalent of Bajaj / Polycab / Philips / Jaquar

LED batten suitable for indoor application 10W 2 feet length sleek and seamless profiled extruded aluminium/ polycarbonate batten with efficient diffuser and integral electronic driver including two point surface mounting on wall/ ceiling and connecting up with twin core twisted flexible copper conductor cable of suitable size including taking down existing unserviceable tube light fittings complete all as directed. Make : Wipro Cat part No LL20-111-XXX-65NE3 or equivalent of Bajaj / Polycab / Philips / Jaquar

Exhaust fan, metal body, single phase 230 volts AC of 300 mm sweep, 1400 RPM with louvers and connecting up with provision of porciline connector and flexible three core copper conductor of 0.5 sqmm size from terminal point complete all as directed. Make:- Bajaj model Freshee MK-II product code 70003 or equivalent of Crompton / Havells

Water heater storage type electric, capacity 25 litres, BEE 5 star rated and prewired and including connecting up with three core copper conductor cable with 15 Amp plug top complete all as dirceted. Make:- Bajaj Model Shakti GPV product code 150747 or equivalent of crompton / Havells.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (Earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connecting with steel GI earth wire 4 mm dia by means of bolt nut check nuts and washers including PCC pit with 1:2:4 type B-1 using 20mm graded stone aggregate and frame cover of angle iron 25x25x6mm, MS sheet 3mm thick and handle of 6mm dia MS bar made to shape, GI medium grade 20mm bore pipe for watering common salt chorcoal funnel wiremesh earth work in any type of soil returning filling in and removal of soft/loose soil to a distance n.exc 5 mtr including earth test point and making connections testing on completion all as per electric plate No 3 of SSR Part-I, complete all as directed.

River sand to required width at bottom and top for cable cushioning (8 cm before laying the cable and 15 cm after laying the cable) complete all as directed

Common burnt clay old size bricks of sub class B (designation 75) laid at right angle to the cable in trenches for cable protection complete all as directed.

Supply, laying, jointing, testing and comissioning, cable XLPE insulated, armoured and PVC sheathed LT 1100 volts grade and aluminum conductor confirming to IS 7098 laid in trenches / through pipe / floor / fixed wall etc. for size of cables 35 Sqmm 3.5 core complete all as directed.

GI pipe 40 mm bore, light grade, as in cable protection under road / floor / fixed to wall / panel etc. complete all as directed.

Less Schedule "A" Credit (For Detail description, and rate of particular item, Please refer Schedule "A" Credit Page as attached in Tender Doccuments)

ABHISHEK CONSTRUCTIONS

VIKAS CONSTRUCTIONS

M.VENKATARAMANAPPA AND COMPANY

Srisrinivasaenterprises

D NAGI REDDY

Moulya Builders

S L R Construction

Elite Constructions

K. VENKATESH NAIDU