PROVISION OF 01 X PARKING SHED NEAR RECORD CLK MESS OF 39 GR, 65 X GEYSERS FOR OR MD ACCN AND SPL REPAIR TO BLDG OF 39 GTC AT VARANASI CANTT UNDER GE (EAST) PRAYAGRAJ.

Amount

Demolition of cement concrete of any description and in any position is reinforced (reinforcment cut as required to facilitate demolition) not other wise specifically provided complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

M & L for 25mm thick Cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in levelling course, benching etc, finished even & rough to receive cement mortar screed bed complete all as specified and directed.

M & L for 75mm thick Cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) in levelling course,for floor benching etc, finished even & rough to receive cement mortar screed bed complete all as specified and directed.

M&L for chequered cement concret tiles 25 cm x 25 cm x 22-25 mm thick, machine pressed set jointed and pointed in neat cment slurry in floors with grey cement and pigment over and including 15 mm thick screed bed in CM(1:6) complete all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) in plinth protection,, finished even and smooth witht using extra cement, complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for Non - skid Coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 20 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

All as per item No. 08 above but as in vertical surfaces such as skirting/ dado over and including rendering layer 10 mm thick in CM (1:4) complete all as specified and directed.

M&L for Glazed ceramic tiles in vertical surface 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match in coloured cement to match tiles over and including 10 mm thick rendering layer in CM (1:4) complete all as specified and directed.

M&L for Machine cut Kota stone slab flooring 18-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab over and including 20 mm thick screed bed or bedding layer in CM (1:4) including rubbing and polishing complete all as specified and directed.

M&L for Kota stone slab 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed base with grey cement mixed with pigment to match the shade of slab over and including 10 mm thick screed bed or bedding layer in CM (1:4) including rubbing and polishing complete all as specified and directed.

Demolition of brick work built in cement or cement lime mortar complete all as specified and directed.

M&L for Brick work with old size subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for Brickwork with old size subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4 complete all as specified and directed.

Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick on wall in cement mortar 1:6 on other than faces of brick work or concrete surfaces, finished even and fair complete all as specified and directed.

M&L for rendering 10 mm thick on wall in cement mortar 1:4 on fair faces of brick work or concrete surfaces, finished even and fair complete all as specfied and directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even and fair complete all as specfied and directed.

S&F GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste complete all as specfied and directed.

M&L for preparing new plastered surfaces of walls and applying two coats of Oil bound distemper (smooth wall finish) in approved colour/shade over a coat of primer over wall care putty complete all as specified and directed .

M&L for preparing new plastered surfaces of walls and applying two coats of cement base paint (smooth wall finish) in approved colour/shade over a coat of primer over wall care putty complete all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces of ceiling surfaces and applying three coats of white wash complete all as specified and directed.

M&L for complete removal of existing treatment from walls (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces and prepairing old decorated plastered surfaces of wall including cornices,pilastered etc. and applying two coats of Oil bond distemper over one coat of primer over wall care putty on wall surface complete all as specified and directed.

M&L for complete removal of existing treatment from walls (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces and prepaing old decorated plastered surfaces of wall including cornices, pilastered etc. and applying two coats of cement base paint over wall care putty on wall surface complete all as specified and directed.

M&L for complete removal of existing treatment (any number of layers) from old surfaces of ceiling and applying two coat of white wash complete all as specified and directed.

Dismantaling of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and directed.

M&L for 15-20mm thick Green Marble work (table rubbed and polished) for wall lining (veneering to wall) over and including 15mm thick rendering in CM 1:4 and pointing with white cement (1:2) using marble dust and admixture of pigment to match with shade, complete all as specified and directed .

Taking down chowkhat with shutters (W/O taking off shutters from the frame) area of opening exceeding 1.50 Sqm but not exceeding 4 Sqm each complete and all as specified and directed

Taking down chowkhat with shutters (W/O taking off shutters from the frame) area of opening not exceeding 1.50 Sqm each complete and all as specified and directed

S&F factory made 35 mm thick 2nd class HW of plain framed panelled shutter ( two panels ) with lock rail, panels of timber flat on both sides feather edged or of veneered particle board medium density or particle board with commercial face complete all as specified and directed.

M&L for 35mm thick glazed and skeleton shutters of 2nd class HW open rebated and prepared to receive glass or gauze etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitered bead for securing glass/gauze etc size of shutter as specified in SSR part I section 8, clause 8.24(a) complete and all as specified and directed

S&F factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 42x50 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified and directed.

S&F factory made 30 mm thick Poly vinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60mm x 30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and jointed at the corners by means of M.S. galvanised/ plastic brackets of size 75mm x 220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickenss. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm ( + 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. Thepanels filled vertically and tie bar at two places by insering horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete all as specified and directed.

M&L for Rolled mild steel sections conforming to Gde Fe-410-0 (Grade E-250) quality A as in framing for cladding, glazing and the like including door frames/chowkats, fixed with angle cleats and connecting plates, etc complete all as specified and directed.

M&L for PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) as in filling hold fast openings includnig necessary form work complete all as specified and directed.

S&F 200 mm long aluminium anodised tower bolt, complete and all as specified and directed of extruded section complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door bolt 250 mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F butt hinges, medium weight, cold rolled mild steel, 100 mm size complete all as specified and directed.

S&F aluminium handles, cast type anodised 150mm size complete all as specified and directed.

S&F aluminium handles, cast type anodised 100mm size complete all as specified and directed.

S&F hasp and staple 150 mm size, safety type aluminium anodised with mild steel hinge pin including bolt to hinge plate, fixed with screws complete all as specified and directed.

Supply only Second class hard wood small fittings such as brackets of any type, shaped door and window stops and the like, including all necessary labours, articles not exceeding 200 cu. cm each complete all as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel, 50 mm size complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete and all as specified and directed

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed complete and all as specified and directed

M&L for 18/19mm thick prelaminated particle board, exterior grade prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, complete all as specified and directed .

S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps 30mm (when open) complete all as specified and directed.

S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, with glazing bars complete all as specified and directed.

S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, without glazing bars complete all as specified and directed.

S&F in repair for factory made steel ventilators with top hung shutter including hinges, steel peg stay including two coats of synthetic enamel paint over a coat of red oxide primer after preparation of new steel surfaces complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sqm in each panes complete and all as specified and directed

S&F 3mm thick Figured glass, pin headed type and glazing with oil putty in squares not exceeding 0.5 sqm in each pane complete all as specified and directed.

S&F in repair of 3mm thick sheet glass ordinary quality, and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane, complete all as specified and directed .

M&L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed .

M&L for preparation of new surfaces of wood and wood based materials of any description over 10 cm in width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old painted surfaces of wood and wood based materials of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted steel & iron surfaces of any description over 10 cm in width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel & iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for reinforced cement concrete(RCC) 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in chajjas (reinforcement to be measured separately) complete all as specified and directed.

M&L for form work to chajja or slab and similar work for flat rough finished surface of concrete complete all as specified and directed.

M&L for mold steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 6 to 8 mm dia as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exc 10cm girth complete all as specified and directed.

Taking up or down steel tubing and connections and supply and fixing 15mm dia GI steel tubes, medium grade with all fitting and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

Taking up or down steel tubing and connections and supply and fixing 20mm dia GI steel tubes, medium grade with all fitting and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

Taking up or down steel tubing and connections and supply and fixing 25mm dia GI steel tubes, medium grade with all fitting and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed as fixed in repair complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 500 litres capacity, ISI marked double layered, hoisted and fixed in position including connecting up pipes including ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (minimum weight 210 gms) including dismantling water tanks and removeing from site complete all as specified and directed.

S&F in repair 20mm PVC nipple suitable for HDPE water tank. (Minimum weight 45gms) complete all as specified and directed.

S&F in repair PVC low level flushing cistern 10 litres capacity, white, with all fitting and fixtures including brackets and 32 mm bore PVC flush pipe, complete all as specified and directed.

S&F in repair vitreous china squatting pan ‘Orissa’ pattern, size 580 x 440 mm, white coloured, with integral foot rests, including provision of lime concrete bedding complete all as specified and directed.

S&F in repairs vitreous china wash basin, white, flat back, size 550 x 400 mm including pedestal and brackets and cutting for and pinning in ends of brackets,complete all as specified and directed.

S&F in reapir stainless steel soap dish of grade 304 of pattern kept in AGE's office or as approved by Engg-in-charge complete all as specified and directed.

S&F in repair Brass chromium plated shower rose 125 mm size with swivel joints, any pattern as approved by Engg-in-charge complete all as specified and directed.

S&F in repair Tubular towel rail of brass chromium plated, 20 mm dia, 'D' type, 60 cm long between flanges including brackets complete all as specified and directed.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F in repair fancy type bib taps cast copper alloy chromium plated with crutch or butter fly handle screwed down screwed for iron pipe 15mm bore complete all as specified and directed.

S&F in repair 15 mm dia fancy type chromium plated angle valves with long shank and cup, cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete and all as specified and directed

S&F in repair 15 mm dia stop valves cast copper alloy chromium plated long shank(concealed type), screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed.

S&F in repairs grating doom 125 mm dia with waste hole of PTMT (min weight 40 gms) complete all as specified and directed.

S&F stainless steel tubing of 25 mm dia, 304 grade, heavy quality for curtain rod fancy type including CP brabs brackets, socket and knobs (wall to wall or flush to wall) for securing to curtain rod, fixed in repair complete all as specified and directed.

S&F in repair 110mm PVC (SWR) pipes single socketed , in any length with rubber ring, joints, laid in trenches or in floors complete all as specified and directed.

S&F in repair 110mm PVC (SWR) pipes single socketed , in any length with rubber ring, joints,fixed to walls complete all as specified and directed.

S&F in repair 75mm PVC (SWR) pipes single socketed , in any length with rubber ring, joints, laid in trenches or in floors complete all as specified and directed.

S&F in repair 75mm PVC (SWR) pipes single socketed , in any length with rubber ring, joints ,fixed to walls complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction single (Single T)equal or unequal complete all as specified and directed.

S&F 75mm bore PVC (SWR) junction single (SingleT)equal or unequal complete all as specified and directed.

S&F 110mm PVC (SWR) Vent cowl complete all as specified and directed.

S&F 75mm PVC (SWR) Vent cowl complete all as specified and directed.

S&F in repairs PVC (SWR) floor trap, plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrte type B-1 (1:2:4) suitable for 75mm bore pipe complete all as specified and directed.

Demolition and breaking up drain pipes Internal dia of pipe in 150 mm (Salt glazed ware, AC or Reinforced concrete) set in cement mortar ® complete all as specified and directed.

M&L for 150mm dia Salt-glazed stoneware drain pipes laid in trenches and jointed as specified including Bends and taper bends, any radius complete all as specified and directed.

M&L for plain cement concrete (PCC) 1:3:6 type C2 (using 40mm graded stone aggregate) as in bed to 150 mm bore drain pipes including packing under and haunching completely surrounding pipes with concrete after they are laid and tested; in, complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F Stainless steel plate rack (utensil rack) of size (600mm x 750mm) and depth 300mm made with 0.63mm thick stainless steel sheet provided with brass screw including necessary fittings, nut/bolts fixed in repairs complete all as specified and directed.

S&F in repair Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/ plastic cleats (minimum weight 300 gms) complete all as specified and directed.

S&F in reapair 15mm bore fancy type pillar tap cast copper alloy with capstan head chromium plated screwed down high pressure with or without lettered 'hot' or 'Cold' with long screwed shanks and fly nuts fixed to pipe complete all as specified and directed.

M&L for Plain cement concrete, 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) as in surface channels or drains, complete all as specified directed.

M&L for Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc, complete all as specified directed.

M&L for plain cement concrete(PCC) 1:2:4 type B0(using 12.5mm graded crushed stone aggregate) in roof kerbs or mud stops, roof padding, rounded or chamgered on edges, complete all as specified and directed.

M&L for apply a glass fibre reinforced acrylic modified cementitious coating system to the sunken portion of roof complete all as specified here -in-under:- (i) Prepration of surface of sunken portionby removing dust loose particles etc . (ii)Application of one coat of glass fibre reinforced acrylic modified cementitious coating @ 1.5 kg/m2 over reinforcement / over base etc (iii) Apply a protection plaster (12–15 mm) admixed with appropriate integral waterproofing compound @ 0.20 kg per bag of cement. The product should conforms to IS 2645. (iv) Sealaing of pipe penetration of toilets core cutting by appling solvent free, moisture insensitive epoxy resin based patch repair putty on pipe penetration surfaces. The putty shall be applied to a groove thickness of minimum 20mm on pipe penetration joint to concrete

M&L for PCC 1:4:8 type D-2 (using 40 mm graded stone agg) as in filling sunken floors, paving /mass consrete and any position and any thickness complete all as specified and directed.

Removing / taking down of old water proofing treatment from roof/concrete surfaces (All layers ie levelling cource, plaster and memberan, mud etc but except tiles) including cleaning of concrete surface so as to ready for receiving new WPT and removal takingdown/ dismentaled material to distance exceeding 250 Mtr complete all as specified and directed.

M&L for providing water proofing treatment over cleaned roof surface with APP modified bitumenous membrane weight not less than 3 Kg per Sqm comprising of the following and testing complete:- [a] 10 mm thick rendering or screed bed or bedding layer in cement sand mortar 1:4 mixed with water proofing compound @ 3%by weight of cement and surface finished even & fair. [b] Applying one coat of bitumen primer @ 0.3 Litre per Sqm on plastered surface. [c] Applying one coat of hot blown bitumen 85/25 grade @ 1.2 Kg per Sqm. [d] Providing APP modified polymeric water proofing membrane having weight not less than 3 Kg per Sqm with 100 mm wide side or end lap and joint sealed with flamed torched pasted over full length [e] Applying one coat of hot blown bitumen 85/25 grade @ 1.2 Kg per Sqm. [f] Spread coarse sand over entire bitumen surface and than topping with 40mm thick brick tiles laid over & including 15 mm thick screed bed in cement sand mortar 1:6 & joints shall be pointing with CM 1:3 complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averging 15 cm deep and getting out hard/dense soil complete all as specified and directed.

M&L for Reinforced cement concrete (design mix) M-25 , (using 20 mm graded stone aggregate) in foundations, including rafts, footings, foundation beams, plinth beams based for columns etc complete all as specified and directed.

M&L for Reinforced cement concrete (design mix) M-25 , (using 20 mm graded stone aggregate) columns, pillars, piers, posts and struts etc complete all as specified and directed.

M&L for Reinforced cement concrete (design mix) M-25, (using 20 mm graded stone aggregate) slabs supported on walls, beams, and columns in floors, roofs, landings balconies, canopies deck slabs and in shelves and the like complete all as specified and directed.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to batter for rough finishes on flat surfaces of concrete wall, complete all as specified and directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.for rough finishes, complete all as specified and directed.

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions, Square, Circular rectangular on plan or polyg- for rough finishes complete all as specified and directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finishes complete all as specified and directed.

M&L for mild steel bars 5 mm dia over upto and including 10 mm dia in stirrups, spaces and binders bent to shape required including cranking, bending and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified & directed.

M&L for hard core of broken stone or boulders gauge n exc 63 mm deposited spread and levelled in layers not exceeding 15 cm thick, watered and rammed to ature surface complete all as specified and directed .

M & L for 75mm thick Cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in levelling course for floor benching etc, finished even & rough complete all as specified and directed .

M&L for 100 mm thick PCC 1:2:4 type B-1, (using 20 mm graded stone aggregate), finishing cement concrete surface even and smooth Without using extra cement in floors complete all as directed .

M&L for machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade and with grey cement and pigment including 25mm thick sand cushing complete all as specified and directed.

M&L for 75 mm thick PCC type C-2, 1:3:6 (using 40 mm graded stone aggregate) as in plinth protection finished even and smooth complete all as specified and directed.

M&L for Brick work with fly ash old size bricks, straight or curved on plan exceeding 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L plain cement concrete type C-2, 1:3:6 using 40mm graded aggregate as in surface channel and drain complete all as specified and directed

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed

M&L for point wiring complete with PVC insulated unsheathed, 1100 volts grade cable 1.5 Sqmm (nominal area) FRLS type multi stranded copper conductor, single core drawn in and including not less than 20 mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring for one light/ fan/ bell/ buzzer/ exhaust fan point controlled by one, one way switch, including concealed pressed steel terminal box of required size not less than 1.0 mm thick factory made duly painted inside & outside with two coats of black bituminous paint over & including a coat of red oxide primer, with 2.8 mm thick top cover of plastic laminated sheet of required colour for mounting switch, sockets, fan regulator etc including 1.5 Sqmm FRLS type PVC insulated unsheathed cable multi-stranded copper conductor as continuous earth wire and connected to earth dolly as required at site& including chases cutting & making good disturbed surface & applying finishes to match existing surface complete all as specified and directed.

Ditto- all as item No.128 here-in-before but for one light controlled by two way switch

Ditto- all as item No. 128 here-in-before but for one 3 pin, 5amp socket out let on independent board

Ditto -all as item No.128 here-in before but for 3pin ,5amp socket out let on the same board with other switch complete all as specified and directed.

M&L for point wiring complete with PVC insulated unsheathed, 1100 volts grade cable 2.5 Sqmm (nominal area) FRLS type multi stranded copper conductor, single core drawn in and including not less than 20 mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring for one light/fan/bell/buzzer / exhaust fan point controlled by one, one way switch, including concealed pressed steel/PVC terminal box of required size not less than 1.0 mm thick factory made duly painted inside & outside with two coats of black bituminous paint over & including a coat of red oxide primer, with 3 mm thick top cover of plastic laminated sheet of required colour for mounting switch, sockets, fan regulator etc including 2.5 Sqmm FR type PVC insulated unsheathed cable solid copper conductor as continuous earth wire and connected to earth dolly as required at site& including chases cutting & making good disturbed surface & applying finishes to match existing surface complete all as specified and directed.

M&L for sub main wiring with three single core PVC insulated & unsheathed cable 6.0 Sqmm (nominal area) FRLS type having multi-stranded copper conductor (phase, earth and nutral) drawn in and including 20/25 mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring , earth wire connected to common earth as per IS including necessary cutting chasing for conduit & sinking for boxes & making good to walls disturbed surface to match existing surface complete including taking down of exsting sub main wiring complete all as specified and directed. NOTE : Three runs of 6 Sqmm cable and PVC conduit shall be measured as a one unit length.

S&F for switch piano, flush type, 5 amps, single pole, one way, 230 volt complete all as specified and directed.

S&F for switch piano, flush type, 5 amps, single pole, two way, 230 volt complete all as specified and directed.

S&F bell push switch 5 Amp flush type complete all as specified and directed.

S&F for 5 pin, 5 Amp/ 6 Amp , socket outlet, flush type, 2 in 1 complete all as specified and directed.

S&F for bell, ding- dong , AC, 230 Volt, single pole complete all as specified and directed.

S&F stepped type electronic fan regulator flush type AC 230 volt suitable for any type of ceiling fan complete all as specified and directed.

S&F lamp holder PVC/Polycorbonate type with cord grip cap/back plate suitable for batten/angle /pendent fitting complete all as specified and directed.

S&F LED retrofit lamp of capacity 9 watt with B-22 CDL holder base with polycabonate body and aluminium heat sink day light inverter bulb complete including taking down old/ unserveciable CFL/bulb complete all as specified and directed.

S&F switch socket combination 2 in 1, 6 pin 16Amps multipurpose type 240 volts complete all as specified and directed.

S&F single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB single pole 20 amp complete all as specified and directed.

S&F ceiling rose single phase, PVC poly carbonate,insulated body three terminals ISI marked complete all as specified and directed.

S&F in repair for sheet metal enclousre factory made for MCB DB's SPN, 8 way, double door, 240 Volts with 200 Amp rated bus bars complete all as specified and directed.

S&F MCB SP 240 Volt 6 to 40 Amp ISI marked conforming to 'B" curve, breaking capacity 10 KA complete all as specified and directed.

S&F ELCB (Earth leakage circuit breaker) with MCB SPN 240V, 40 amp 30mA for earth leakage,over load and short circuit protection ISI marked complete all as specified and directed.

S&F in repair sheet metal enclosure for VTPN DB double door 415 Volt with 200 amp rated bus bar complete 4 Way with suitable for 1 x 63Amp MCCB as incomer and MCB SPN as outgoing connection through proper size of lugs and cable glands complete all as specified and directed.

S&F MCCB 63 Amp,4 pole ,415 Volt ISI marked conforming to 'B" curve, breaking capacity 16 KA complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below GL with top edge of plate not less than 1.50 m below normal ground level) connected to galavanised earth lead wire 4.0 mm dia (7.5m) as means of bolts, nuts, check nuts and washer besides brazing at all joints as shown on drawings and including excavation, earth work, GI pipe (ISImark) light grade 15 mm bore for protection of GI wire from earth electrode to and including the earth test point, supplying and laying charcoal dust, common salt, PCC 1:3:6, type C-1(using 20 mm graded crushed stone aggregate ) chamber and mild steel angle iron frame 40 x 40 x 3 mm and 40 mm thick pre-cast RCC cover 1:2:4 , type B-1(using 20 mm graded crushed stone aggregate ) reinforced with 8 mm dia TMT bars @ 75 mm C/C both ways with mild steel handle 12 mm dia, PGI funnel and wire mesh, 20 mm dia GI pipe light grade(ISI marked) for watering all as shown in electrical plate No 3 of SSR Part-I and connected to earth test point including testing of earthing & dismantling /taking down existing old / unserveciable earthing complete all as specified and directed. (Note:- The rates quoted shall also deemed to include the cost of Earth test point and earth wire and protection pipe upto 7.5 meter beyond the earth plates electrode.)

Supplying ,laying, commissioning & testing cross sectional area 25 Sqmm , 3.5 core XLPE cable insulated armoured, electric power cables (heavy duty) 1100 Volts grade with standard aluminium conductor including taking down existing old /unserveciable cable complete all as specified & directed. Note: Excavation & earth work, sand cushioning & Bricks shall be measured & paid separately under respective item

Excavation in trenches in soft/loose soil not exceeding 1.5 M wide and not exceeding 1.5 Mtr deep and getting out including filling bottom surface to required level or slope for laying of pipes/ cables complete all as specified and directed.

Returning filling including spreading, leveling, watering and well ramming in layers not exceeding 25 cm in soft soil complete all as specified and directed.

Removing excavated surplus soil not exceeding 50 Mtr and depositing where directed at a level not exceeding 1.5 Mtr above the starting point complete all as specified and directed.

M&L for sand cushioning with dry local sand for cable protecting under ground cable (8 cm before laying the cable and 15 cm after laying the cable) in trenches including punning the sand upto 18 cm thick and consolidated complete all as specified and directed. Note : Punned thickness 18 cm shall be measured only.

Supply and laying dry well burnt locally available brick sub class 'B' modular bricks laid flat with width equal to the length of whole bricks over cable as cable protection complete all as specified and directed.

M & L for bore hole for passing cable through / insertion of 40/50 mm dia GI pipe under PCC road/ taxi track/ runway/ hard standing upto the depth 450mm to 1200 mm complete all as directed by Engineer-in-charge. NOTES :- (i) Cost of equipments, tools & plants,material required for boring shall be deemed to be included in unit quoted rates above. (ii) GI pipe shall be measured and paid separetely.

S&F for 40/50 mm dia GI pipe 'light grade' ISI marked including fittings such as bends, tees, sockets etc fixed on wall/pole or laid in trenches under road crossing/hard standing including taking out old /unserveciable existing pipe complete all as specified and directed.

S&F LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose including connection complete all as specified and directed.

S&F LED integral ultra slim round shape surface mounting high power LED luminaire , dome shape opal diffuser lamp of capacity 18w complete including taking down old/ unserveciable CFL/bulb complete all as specified and directed.

S&F in repair wall lamp/comet wall light unique Aesthetic white colour having suitable holder for B-22 Bulb complete all as specified and directed.

S&F in repair LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed

S&F exhaust fans of metallic body heavy duty AC single phase 230/ 240 V of size 300 mm sweep with bracket, louver shutters, nuts & bolts including connection with PVC copper flexible wire for Exhaust fans complete all as specified and directed.

S&F in repair Building security/street LED light fitting 35 watt IP-65 protection pressure diecast alluminium body ,heat resistant glass ,including driver and making necessary electric connection with 2.5 sqmm twin core copper wire 1.5 long complete including fixed on GI pipe of suitable size with mounting bracket complete all as specified and directed.

S&F LED bldg security light 45 Watt of Make-Orient Fiesta Plus cat part No LSFS-045-C or equivalent complete with GI pipe 40mm dia service bracket bend to shape with clamp/nut bolts as required complete all as specified & directed.

Supplying ,laying, commissioning & testing cross sectional area 10 Sqmm , 2 core XLPE cable insulated armoured, electric power cables (heavy duty) 1100 Volts grade with standard aluminium conductor including taking down existing old /unserveciable cable complete all as specified & directed. Note: Excavation & earth work, sand cushioning & Bricks shall be measured & paid separately under respective item

Supplying, laying, commissioning & testing cross sectional area 25Sqmm, 4 core XLPE cable insulated armoured, electric power cables (heavy duty) 1100 Volts grade with standard aluminium conductor including taking down existing old /unserveciable cable complete all as specified & directed. Note: Excavation & earth work, sand cushioning & Bricks shall be measured & paid separately under respective item

Supplying, installation and testing of energy efficient five star rating electric water heater 25 litres 2 KW (Geyser), ISI marked including fixing the water heater (geyser) on wall with and includng nuts bolts/anchoring bolts and making water/electric connection and making good disturbed surface of wall to match the existing complete all as specified and directed

M&L for sub main wiring with PVC insulated 1100V grade FRLS single core multi stranded copper conductor cable of size 2 x 4 sqmm + 1 x 4 sqmm as earth continuity cable passing through and including 25/20mm dia PVC conceal conduit complete all as specified & directed. Note - Three runs of 4 Sqmm including PVC conduit shall be measured as unit length.

M&L for laying in fixing on wall GI Pipe 15mm dia medium grade including all fittings and fixtures complete all as specified & directed.

S & F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified & directed.

S & F PVC connections 15mm size with PTMT nuts of length 300 mm complete all as specified & directed.

S&F fancy type chromium plated Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe of size 15mm dia complete all as specified & directed.

S & F Switch piano, flush type single pole, one way 15 Amp complete all as specified & directed.

S&F 15 mm dia fancy type chromium plated with long shank and angle valve cast copper alloy screwed down type high pressure with cruth or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed.

Prem Singh

M/S DEEKSHA CONSTRUCTION

GAYDIN CONSTRUCTIONS

GANGETIC DOLPHIN

M/s SKP CONSTRUCTION