Construction of drain from super shopie to H/o.Lt.Sh.Sansar chowdhary H/o. Sh.S.R.Amla and upto H/o. Anu Gupta sec-5 and various other locations in W.No 42

Amount

Demolishing RCC work manually/by mechanical means including stacking of steel bar and disposal of unserviceable material with in 50 mtrs lead as per direction of engineer-in charge.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 m lead. As per direction of engineer–in-charge.1:3:6. or richers mix(I/c equivalent design mix)

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 min width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed. (All kind of soil 1 meter from cutting Edge)

Removal of Excavated mulba dismantled unserviceable material from the site of work by mechanical transport or manual means or animal means including loading and unloading complete job

Providing under layer including preparation of ground 75mm thick (un compacted) layer of dry stone aggregate & grouted with sand. (Complete Job).

Providing & laying in position cement concrete of specified grade including curing but excluding the cost of cenetring & shuttering –All work up to plinth level with 1:3:6(1 Cement: 3 Coarse sand: 6graded stone agg. 20mm nominal size) .

Providing & laying in position cement concrete of specified grade including curing but excluding the cost of centering& shuttering –All work up to plinth level with 1:2:4(1 Cement: 2 Coarse sand: 4graded stoneagg. 20mm nominal size) .

Providing & laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centring , shuttering, finishing and reinforcement-All work up to plinth level.1:1.5:3(1 Cement: 1.5 Coarse sand: 3graded stone agg. 20mm nominal size).

Steel Reinforcement for R.C.C. works including straightening, cutting, bending, placing in position and binding all complete above plinth level mild steel and medium tensile steel bars.

Steel work welded in built up sections/framed work including cutting hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bars, ladders, railings, brackets, gates and similar works.

Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Centering & shuttering including strutting propping etc. & removal of form for: Foundations, footings, bases of columns etc for mass concrete.

12mm Cement Plaster of 1:6 mix (1 cement : 6 fine sand)

Carriage of materials by mechanical transport including loading/ unloading & stacking complete. Sand

Carriage of materials by mechanical transport including loading/ unloading & stacking complete. Stone aggregate below 40mm Nominal size

M/S Sanjeev Sharma