Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹24.1 LAccepted-AOC RZ A2 2 CHANAKYA PLACE PART I OPP C 1A BLOCK JANAK PURI NEW DELHI 110059 | NEW DELHI | WEST DELHI | DELHI | 110059 | L1 | Accepted-AOC BEING L1 | |
| 2 | L2₹34.9 L+₹10.3 L (41.7%)Rejected-Finance WZ 409 0 B 1ST FLOOR PLOT NO 12 JANAK PARK HARI NAGAR NEW DELHI 110064 | NEW DELHI | WEST DELHI | DELHI | 110064 | L2 | Rejected-Finance NOT BEING L1 |
| Sl No | Description | Qty | Unit | RUCHIKA ENGG.WORKS L1 | Flint India L2 |
|---|---|---|---|---|---|
| 1.00 | M&L for servicing/repair of Washer Extractor upto 120 Kg capacity of Make : Fabcare including opening, dismantling of the machine, disconnecting all steam / water and electrical connection, cleaning / servicing of drum, balancing/alignment of drum & shaft cleaning, steam trap, servicing/ lubricating/greasing and adjusting the mechanical and electrical driving equipment, shaft assembly, bearing / bush, in and including change of lubricating oil,grease,all rubber gaskets/ packing of all equipments and oil seales as per OEM make and replacement of all kinds of minor defective / spares parts i.e. wire, lugs, nut, bolts,screw etc and all machine work i.e. welding, cutting, drilling, lathe work etc in and including repair/replacement of defective spares parts complete all as specified and directed by Engr-in-Charge.
Note:
1. The parts replaced shall be measured seperately under relevent item.
2. Any other defective part or part which is likely to fail and not present in schedule and need to be replaced for making machine serviceable for proper operation shall be replaced by contractor at no extra cost and cost of item is deemed to be included in quoted rate.
3. Cost of taking out drum for correcting the alignment and balancing is deemed to be included in quoted rates.
4. Cost of T&P and transportation is deemend to be incuded in quoted rates.
5. If any defect occur till next service during CA period then contractor will carry out repair and replace the defective part of machine at no extra cost. | 15 | Each Job | 8,000 ₹1,20,000 Lowest | 10,000 ₹1,50,000 |
| 2.00 | M&L for servicing/repair of Washer Extractor upto 60 Kg/ Dry Cleaner capacity of Make : Fabcare including opening, dismantling of the machine, disconnecting all steam / water and electrical connection, cleaning / servicing of drum, steam trap, servicing/ lubricating/greasing and adjusting the mechanical and electrical driving equipment, shaft assembly, bearing / contact, governor jaws in and including change of lubricating oil,grease,all rubber gaskets/ packing of all equipments and oil seales as per OEM make and replacement of all kinds of minor defective / spares parts i.e. wire, lugs, nut, bolts,screw etc and all machine work i.e. welding, cutting, drilling, lathe work etc in and including repair/replacement of defective spares parts complete all as specified and directed by Engr-in-Charge.
Note:
1. The parts replaced shall be measured seperately under relevent item.
2. Any other defective part or part which is likely to fail and not present in schedule and need to be replaced for making machine serviceable for proper operation shall be replaced by contractor at no extra cost and cost of item is deemed to be included in quoted rate.
3. Cost of taking out drum for correcting the alignment and balancing is deemed to be included in quoted rates.
4. Cost of T&P and transportation is deemend to be incuded in quoted rates.
5. If any defect occur till next service during CA period then contractor will carry out repair and replace the defective part of machine at no extra cost. | 3 | Each Job | 4,000 ₹12,000 Lowest | 10,000 ₹30,000 |
| 3.00 | M&L for servicing/repair of Washer Extractor upto 100 Kg capacity of Make : Stefab including opening, dismantling of the machine, disconnecting all steam / water and electrical connection, cleaning / servicing of drum, steam trap, servicing/ lubricating/greasing and adjusting the mechanical and electrical driving equipment, shaft assembly, bearing / contact, governor jaws in and including change of lubricating oil,grease,all rubber gaskets/ packing of all equipments and oil seales as per OEM make and replacement of all kinds of minor defective / spares parts i.e. wire, lugs, nut, bolts,screw etc and all machine work i.e. welding, cutting, drilling, lathe work etc in and including repair/replacement of defective spares parts complete all as specified and directed by Engr-in-Charge.
Note:
1. The parts replaced shall be measured seperately under relevent item.
2. Any other defective part or part which is likely to fail and not present in schedule and need to be replaced for making machine serviceable for proper operation shall be replaced by contractor at no extra cost and cost of item is deemed to be included in quoted rate.
3. Cost of taking out drum for correcting the alignment and balancing is deemed to be included in quoted rates.
4. Cost of T&P and transportation is deemend to be incuded in quoted rates.
5. If any defect occur till next service during CA period then contractor will carry out repair and replace the defective part of machine at no extra cost. | 9 | Each Job | 3,000 ₹27,000 Lowest | 10,000 ₹90,000 |
| 4.00 | M&L for servicing/repair of Flat work ironner of Make : Fabcare including opening, dismantling of the machine, disconnecting all steam / water and electrical connection, cleaning / servicing of chest/cylinder, steam trap, servicing/ lubricating/greasing and adjusting the mechanical and electrical driving equipment, shaft assembly, bearing / contact, servicing of blower in and including change of lubricating oil,grease,all rubber gaskets/ packing of all equipments and oil seales as per OEM make and replacement of all kinds of minor defective / spares parts i.e. wire, lugs, nut, bolts,screw etc and all machine work i.e. welding, cutting, drilling, lathe work etc in and including repair/replacement of defective spares parts and servicing of gear box, greasing/oiling complete all as specified and directed by Engr-in-Charge.
Note:
1. The parts replaced shall be measured seperately under relevent item.
2. Any other defective part or part which is likely to fail and not present in schedule and need to be replaced for making machine serviceable for proper operation shall be replaced by contractor at no extra cost and cost of item is deemed to be included in quoted rate.
3. Cost of taking out chest/cylinder for correcting the alignment and balancing is deemed to be included in quoted rates.
4. Cost of T&P and transportation is deemend to be incuded in quoted rates.
5. If any defect occur till next service during CA period then contractor will carry out repair and replace the defective part of machine at no extra cost. | 6 | Each Job | 3,000 ₹18,000 Lowest | 4,000 ₹24,000 |
| 5.00 | M&L for service/Over hauling of Drying Tumbler of capacity 50/60 Kg, comprising of opening, dismantling of the machine, disconnecting all steam / water and electrical connection, balancing / alignment of drum/shaft, remattling the shaft by taking it to the lathe work shop, cleaning / servicing of steam heating coil, steam trap, replacing all defective spares parts / items mentioned in Schedule and reassembling all dismantled part/items after carrying out necessary repair as required, including cleaning, servicing, oiling, greasing etc, making all water/steam connection and electrical connection, leak testing at desired pressure, with and including testing, complete all as directed and required at site.
Note:
1. The parts replaced shall be measured seperately under relevent item.
2. Any other defective part or part which is likely to fail and not present in schedule and need to be replaced for making machine serviceable for proper operation shall be replaced by contractor at no extra cost and cost of item is deemed to be included in quoted rate.
3. Cost of taking out drum for correcting the alignment and balancing is deemed to be included in quoted rates.
4. Cost of T&P and transportation is deemend to be incuded in quoted rates.
5. If any defect occur till next service during CA period then contractor will carry out repair and replace the defective part of machine at no extra cost. | 21 | Each Job | 2,000 ₹42,000 Lowest | 5,000 ₹1,05,000 |
| 6.00 | M&L for servicing/overhauling of Hydro extractor capacity of 25 Kg (Make - Stefab), comprising of opening, dismantling and disconnecting all electrical connection, balancing / alignment of cylindrical basket, balancing of drum/shaft, shaft turning, replacing all defective spares parts / items mentioned in Schedule and reassembling all dismantled part/items after carrying out necessary repair as required, including cleaning, servicing, oiling, greasing etc, making electrical connection complete all as specified and directed.
Note:
1. The parts replaced shall be measured seperately under relevent item.
2. Any other defective part or part which is likely to fail and not present in schedule and need to be replaced for making machine serviceable for proper operation shall be replaced by contractor at no extra cost and cost of item is deemed to be included in quoted rate.
3. Cost of taking out drum for correcting the alignment and balancing is deemed to be included in quoted rates.
4. Cost of T&P and transportation is deemend to be incuded in quoted rates.
5. If any defect occur till next service during CA period then contractor will carry out repair and replace the defective part of machine at no extra cost. | 6 | Each Job | 1,000 ₹6,000 Lowest | 3,000 ₹18,000 |
| 7.00 | M&L for service / overhauling of Steam Boiler of 850/650 Kg capacity (Make : Thermax RXD) including disconnecting of water / steam / electric connections, dismantling of boiler plant by unscrewing/cutting of screws, nuts & bolts etc, taking out complete coil assembly and other major parts from the boiler etc, replacing all defective spares parts, cleaning / servicing of coil assembly and descaling, repair/replacement of electrical control panel board, all machine works i.e. welding, cutting, drilling/ lathe etc as and when required and reassembling all dismantled part/items after carrying out necessary repair as required, other material, cleaning, servicing, oiling, greasing etc, making all steam / water connection and electrical connection, leak testing at desired pressure, with and including testing, commissioning of complete boiler plant to entire satisfaction of Engr-in-charge, complete all as specified and directed by Engr-in-Charge.
Note:
1. The parts replaced shall be measured seperately under relevent item.
2. Any other defective part or part which is likely to fail and not present in schedule and need to be replaced for making machine serviceable for proper operation shall be replaced by contractor at no extra cost and cost of item is deemed to be included in quoted rate.
3. Cost of taking out drum for correcting the alignment and balancing is deemed to be included in quoted rates.
4. Cost of T&P and transportation is deemend to be incuded in quoted rates.
5. If any defect occur till next service during CA period then contractor will carry out repair and replace the defective part of machine at no extra cost. | 9 | Each Job | 3,000 ₹27,000 Lowest | 5,000 ₹45,000 |
| 8.00 | M&L for servicing/overhauling of Flat Bed Press comprising of opening, dismantling and disconnecting all electrical connection, replacing all defective spares parts / items mentioned in Schedule and reassembling all dismantled part/items after carrying out necessary repair as required, including cleaning, servicing, oiling, greasing etc, making electrical connection complete all as specified and directed by Engr-in-Charge.
Note:
1. The parts replaced shall be measured seperately under relevent item.
2. Any other defective part or part which is likely to fail and not present in schedule and need to be replaced for making machine serviceable for proper operation shall be replaced by contractor at no extra cost and cost of item is deemed to be included in quoted rate.
3. Cost of taking out drum for correcting the alignment and balancing is deemed to be included in quoted rates.
4. Cost of T&P and transportation is deemend to be incuded in quoted rates.
5. If any defect occur till next service during CA period then contractor will carry out repair and replace the defective part of machine at no extra cost. | 8 | Each Job | 1,000 ₹8,000 Lowest | 25,000 ₹2,00,000 |
| 9.00 | Supply and Fixing, in replacement of Main bearing set of size (6322,2RS and 6323,2RS) (Big & Small bearing) suitable for Washer Extractor of 120/100 Kg capacity complete all as specified and directed by Engr-in-Charge. | 3 | Each Set | 40,000 ₹1,20,000 Lowest | 40,000 ₹1,20,000 Lowest |
| 10.00 | Supply and Fixing, in replacement of Main bearing seal set of silicon suitable for Washer Extractor of 120 Kg capacity complete all as specified and directed by Engr-in-Charge. | 3 | Each Set | 5,000 ₹15,000 Lowest | 10,700 ₹32,100 |
Tender Value
₹45 L
EMD Value
₹90,000
Closing Date
23 May 2025, 6:00 pmClosed
GE E/M RR HOSPITAL DELHI CANTT-10.
GE E/M RR HOSPITAL DELHI CANTT-10.
GE/H-87/2024-25 COMPREHENSIVE AND PREVENTIVE MAINT OF VARIOUS LAUNDRY PLANTS, BOILER, AND EQUIPMENT INCLUDING CONNECTED ITEMS AT AHRR UNDER GE E/M RR HOSPITAL DELHI CANTT-10.
2025_MES_705442_1
GE/H-87/2024-25
Open Tender
Electrical and Maintenance Works
Works
334 days
GE E/M RR HOSPITAL DELHI CANTT-10.
Please refer Tender documents.
10 documents required · 10 mandatory
₹500
GE E/M RR HOSPITAL DELHI CANTT-10.
₹90,000
Yes
28 Aug 2025
25 Apr 2025
26 May 2025
25 Apr 2025
23 May 2025
9 May 2025
Amount
M&L for servicing/repair of Washer Extractor upto 120 Kg capacity of Make : Fabcare including opening, dismantling of the machine, disconnecting all steam / water and electrical connection, cleaning / servicing of drum, balancing/alignment of drum & shaft cleaning, steam trap, servicing/ lubricating/greasing and adjusting the mechanical and electrical driving equipment, shaft assembly, bearing / bush, in and including change of lubricating oil,grease,all rubber gaskets/ packing of all equipments and oil seales as per OEM make and replacement of all kinds of minor defective / spares parts i.e. wire, lugs, nut, bolts,screw etc and all machine work i.e. welding, cutting, drilling, lathe work etc in and including repair/replacement of defective spares parts complete all as specified and directed by Engr-in-Charge. Note: 1. The parts replaced shall be measured seperately under relevent item. 2. Any other defective part or part which is likely to fail and not present in schedule and need to be replaced for making machine serviceable for proper operation shall be replaced by contractor at no extra cost and cost of item is deemed to be included in quoted rate. 3. Cost of taking out drum for correcting the alignment and balancing is deemed to be included in quoted rates. 4. Cost of T&P and transportation is deemend to be incuded in quoted rates. 5. If any defect occur till next service during CA period then contractor will carry out repair and replace the defective part of machine at no extra cost.
M&L for servicing/repair of Washer Extractor upto 60 Kg/ Dry Cleaner capacity of Make : Fabcare including opening, dismantling of the machine, disconnecting all steam / water and electrical connection, cleaning / servicing of drum, steam trap, servicing/ lubricating/greasing and adjusting the mechanical and electrical driving equipment, shaft assembly, bearing / contact, governor jaws in and including change of lubricating oil,grease,all rubber gaskets/ packing of all equipments and oil seales as per OEM make and replacement of all kinds of minor defective / spares parts i.e. wire, lugs, nut, bolts,screw etc and all machine work i.e. welding, cutting, drilling, lathe work etc in and including repair/replacement of defective spares parts complete all as specified and directed by Engr-in-Charge. Note: 1. The parts replaced shall be measured seperately under relevent item. 2. Any other defective part or part which is likely to fail and not present in schedule and need to be replaced for making machine serviceable for proper operation shall be replaced by contractor at no extra cost and cost of item is deemed to be included in quoted rate. 3. Cost of taking out drum for correcting the alignment and balancing is deemed to be included in quoted rates. 4. Cost of T&P and transportation is deemend to be incuded in quoted rates. 5. If any defect occur till next service during CA period then contractor will carry out repair and replace the defective part of machine at no extra cost.
M&L for servicing/repair of Washer Extractor upto 100 Kg capacity of Make : Stefab including opening, dismantling of the machine, disconnecting all steam / water and electrical connection, cleaning / servicing of drum, steam trap, servicing/ lubricating/greasing and adjusting the mechanical and electrical driving equipment, shaft assembly, bearing / contact, governor jaws in and including change of lubricating oil,grease,all rubber gaskets/ packing of all equipments and oil seales as per OEM make and replacement of all kinds of minor defective / spares parts i.e. wire, lugs, nut, bolts,screw etc and all machine work i.e. welding, cutting, drilling, lathe work etc in and including repair/replacement of defective spares parts complete all as specified and directed by Engr-in-Charge. Note: 1. The parts replaced shall be measured seperately under relevent item. 2. Any other defective part or part which is likely to fail and not present in schedule and need to be replaced for making machine serviceable for proper operation shall be replaced by contractor at no extra cost and cost of item is deemed to be included in quoted rate. 3. Cost of taking out drum for correcting the alignment and balancing is deemed to be included in quoted rates. 4. Cost of T&P and transportation is deemend to be incuded in quoted rates. 5. If any defect occur till next service during CA period then contractor will carry out repair and replace the defective part of machine at no extra cost.
M&L for servicing/repair of Flat work ironner of Make : Fabcare including opening, dismantling of the machine, disconnecting all steam / water and electrical connection, cleaning / servicing of chest/cylinder, steam trap, servicing/ lubricating/greasing and adjusting the mechanical and electrical driving equipment, shaft assembly, bearing / contact, servicing of blower in and including change of lubricating oil,grease,all rubber gaskets/ packing of all equipments and oil seales as per OEM make and replacement of all kinds of minor defective / spares parts i.e. wire, lugs, nut, bolts,screw etc and all machine work i.e. welding, cutting, drilling, lathe work etc in and including repair/replacement of defective spares parts and servicing of gear box, greasing/oiling complete all as specified and directed by Engr-in-Charge. Note: 1. The parts replaced shall be measured seperately under relevent item. 2. Any other defective part or part which is likely to fail and not present in schedule and need to be replaced for making machine serviceable for proper operation shall be replaced by contractor at no extra cost and cost of item is deemed to be included in quoted rate. 3. Cost of taking out chest/cylinder for correcting the alignment and balancing is deemed to be included in quoted rates. 4. Cost of T&P and transportation is deemend to be incuded in quoted rates. 5. If any defect occur till next service during CA period then contractor will carry out repair and replace the defective part of machine at no extra cost.
M&L for service/Over hauling of Drying Tumbler of capacity 50/60 Kg, comprising of opening, dismantling of the machine, disconnecting all steam / water and electrical connection, balancing / alignment of drum/shaft, remattling the shaft by taking it to the lathe work shop, cleaning / servicing of steam heating coil, steam trap, replacing all defective spares parts / items mentioned in Schedule and reassembling all dismantled part/items after carrying out necessary repair as required, including cleaning, servicing, oiling, greasing etc, making all water/steam connection and electrical connection, leak testing at desired pressure, with and including testing, complete all as directed and required at site. Note: 1. The parts replaced shall be measured seperately under relevent item. 2. Any other defective part or part which is likely to fail and not present in schedule and need to be replaced for making machine serviceable for proper operation shall be replaced by contractor at no extra cost and cost of item is deemed to be included in quoted rate. 3. Cost of taking out drum for correcting the alignment and balancing is deemed to be included in quoted rates. 4. Cost of T&P and transportation is deemend to be incuded in quoted rates. 5. If any defect occur till next service during CA period then contractor will carry out repair and replace the defective part of machine at no extra cost.
M&L for servicing/overhauling of Hydro extractor capacity of 25 Kg (Make - Stefab), comprising of opening, dismantling and disconnecting all electrical connection, balancing / alignment of cylindrical basket, balancing of drum/shaft, shaft turning, replacing all defective spares parts / items mentioned in Schedule and reassembling all dismantled part/items after carrying out necessary repair as required, including cleaning, servicing, oiling, greasing etc, making electrical connection complete all as specified and directed. Note: 1. The parts replaced shall be measured seperately under relevent item. 2. Any other defective part or part which is likely to fail and not present in schedule and need to be replaced for making machine serviceable for proper operation shall be replaced by contractor at no extra cost and cost of item is deemed to be included in quoted rate. 3. Cost of taking out drum for correcting the alignment and balancing is deemed to be included in quoted rates. 4. Cost of T&P and transportation is deemend to be incuded in quoted rates. 5. If any defect occur till next service during CA period then contractor will carry out repair and replace the defective part of machine at no extra cost.
M&L for service / overhauling of Steam Boiler of 850/650 Kg capacity (Make : Thermax RXD) including disconnecting of water / steam / electric connections, dismantling of boiler plant by unscrewing/cutting of screws, nuts & bolts etc, taking out complete coil assembly and other major parts from the boiler etc, replacing all defective spares parts, cleaning / servicing of coil assembly and descaling, repair/replacement of electrical control panel board, all machine works i.e. welding, cutting, drilling/ lathe etc as and when required and reassembling all dismantled part/items after carrying out necessary repair as required, other material, cleaning, servicing, oiling, greasing etc, making all steam / water connection and electrical connection, leak testing at desired pressure, with and including testing, commissioning of complete boiler plant to entire satisfaction of Engr-in-charge, complete all as specified and directed by Engr-in-Charge. Note: 1. The parts replaced shall be measured seperately under relevent item. 2. Any other defective part or part which is likely to fail and not present in schedule and need to be replaced for making machine serviceable for proper operation shall be replaced by contractor at no extra cost and cost of item is deemed to be included in quoted rate. 3. Cost of taking out drum for correcting the alignment and balancing is deemed to be included in quoted rates. 4. Cost of T&P and transportation is deemend to be incuded in quoted rates. 5. If any defect occur till next service during CA period then contractor will carry out repair and replace the defective part of machine at no extra cost.
M&L for servicing/overhauling of Flat Bed Press comprising of opening, dismantling and disconnecting all electrical connection, replacing all defective spares parts / items mentioned in Schedule and reassembling all dismantled part/items after carrying out necessary repair as required, including cleaning, servicing, oiling, greasing etc, making electrical connection complete all as specified and directed by Engr-in-Charge. Note: 1. The parts replaced shall be measured seperately under relevent item. 2. Any other defective part or part which is likely to fail and not present in schedule and need to be replaced for making machine serviceable for proper operation shall be replaced by contractor at no extra cost and cost of item is deemed to be included in quoted rate. 3. Cost of taking out drum for correcting the alignment and balancing is deemed to be included in quoted rates. 4. Cost of T&P and transportation is deemend to be incuded in quoted rates. 5. If any defect occur till next service during CA period then contractor will carry out repair and replace the defective part of machine at no extra cost.
Supply and Fixing, in replacement of Main bearing set of size (6322,2RS and 6323,2RS) (Big & Small bearing) suitable for Washer Extractor of 120/100 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply and Fixing, in replacement of Main bearing seal set of silicon suitable for Washer Extractor of 120 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply and fixing, in replacement of main bearing circlip suitable for washer extractor of 120 kg capacity complete all as specified and directed by Engr-in-Charge.
Supply and fix in replacement of drive shaft shaft suitable for 120/100 KG washer cum extractor as per existing shape and size complete all as specified and directed by Engr-in-Charge.
M&L for taking out drive shaft of 120/100 Kg washer cum extractor and remetalling shaft for correcting any misalignment/defect using lathe & welding work as required and refixing the shaft in position complete all as specified and directed by Engr-in-Charge
S&F in replacement Solenoid valve of washer cum extractor 120/100 Kg capacity including necessary electrical and pneumatic connection complete all as specified and directed by Engr-in-Charge.
S&F in replacement shocker of washer cum extractor 120 kg capacity complete all as specified and directed by Engr-in-Charge.
S&F in replacement FRL of washer cum extractor 120/100 kg capacity of existing size and make complete all as specified and directed by Engr-in-Charge.
S&F in replacement V-Belt of washer cum extractor 120/100 Kg capacity of existing size and make complete all as specified and directed by Engr-in-Charge.
S&F in replacement spring of washer cum extractor 120 Kg capacity of existing size and make complete all as specified and directed by Engr-in-Charge.
S&F in replacement hose pipe 2', standard length of washer cum extractor 120 Kg capacity of existing size and make complete all as specified and directed by Engr-in-Charge.
S&F in replacement hose pipe 4.5', standard length of washer cum extractor 120 Kg capacity of existing size and make complete all as specified and directed by Engr-in-Charge.
S&F in replacement water level switch of washer cum extractor 120 Kg capacity of existing size and make complete all as specified and directed by Engr-in-Charge.
S&F in replacement water flexible pipe with metal cladding of standard size and length of washer cum extractor 120/100 Kg capacity of existing size and make complete all as specified and directed by Engr-in-Charge.
S&F in replacement steam flexible pipe with metal cladding of standard size and length of washer cum extractor 120/100 Kg capacity of existing size and make complete all as specified and directed by Engr-in-Charge.
S&F in replacement B/F actuator valve 2' of washer cum extractor 120 Kg capacity complete all as specified and directed by Engr-in-Charge.
S&F in replacement B/F actuator valve 4' of washer cum extractor 120 Kg capacity complete all as specified and directed by Engr-in-Charge.
S&F in replacement steam angle valve 1' complete all as specified and directed by Engr-in-Charge.
S&F in replacement cabin fan of washer cum extractor/drying tumbler of existing size and make complete all as specified and directed by Engr-in-Charge.
S&F in replacement door glass of washer cum extractor 120 Kg capacity of existing size and make complete all as specified and directed by Engr-in-Charge.
S&F in replacement door gasket of washer cum extractor 120/100 Kg capacity of existing size and make complete all as specified and directed by Engr-in-Charge.
S&F in replacement pneumatic door lock of washer cum extractor 120 Kg capacity of existing size and make complete all as specified and directed by Engr-in-Charge.
S&F in replacement VFD 40 HP of washer cum extractor 120 Kg capacity including electrical connection complete all as specified and directed by Engr-in-Charge.
M&L for repair of VFD 40 HP of washer cum extractor 120 Kg capacity including replacement of defective parts/ circuit plate including electrical connection complete all as specified and directed by Engr-in-Charge.
M&L for repair of control circuit plate and display controller of washer cum extractor 120 Kg capacity including replacement of defective parts of circuit plate including electrical connection complete all as specified and directed by Engr-in-Charge.
S&F in replacement of control circuit plate and display controller of washer cum extractor 120 Kg capacity including electrical connection complete all as specified and directed by Engr-in-Charge.
S&F in replacement of timer switch of washer cum extractor 100 Kg capacity including electrical connection complete all as specified and directed by Engr-in-Charge.
S&F in replacement of temperature controller of washer cum extractor 100 Kg capacity including electrical connection complete all as specified and directed by Engr-in-Charge.
Supply and Fixing, in replacement of Main bearing set (Big & Small bearing) suitable for Washer Extractor of 60 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply and Fixing, in replacement of Main bearing seal set of silicon suitable for Washer Extractor of 60 Kg capacity complete all as directed.
Supply and fixing, in replacement of main bearing circlip suitable for washer extractor of 60 kg capacity complete all as specified and directed by Engr-in-Charge.
M&L for taking out drive shaft of 60 Kg washer cum extractor and remetalling shaft for correcting any misalignment/defect using lathe & welding work as required and refixing the shaft in position complete all as specified and directed by Engr-in-Charge
S&F in replacement Solenoid valve of washer cum extractor 60 Kg capacity including necessary electrical and pneumatic connection complete all as specified and directed by Engr-in-Charge.
S&F in replacement shocker of washer cum extractor 60 kg capacity complete all as specified and directed by Engr-in-Charge.
S&F in replacement FRL of washer cum extractor 60 kg capacity of existing size and make complete all as specified and directed by Engr-in-Charge.
S&F in replacement V-Belt of washer cum extractor 60 Kg capacity of existing size and make complete all as specified and directed by Engr-in-Charge.
S&F in replacement spring of washer cum extractor 60 Kg capacity of existing size and make complete all as specified and directed by Engr-in-Charge.
S&F in replacement hose pipe 4.5', standard length of washer cum extractor 60 Kg capacity of existing size and make complete all as specified and directed by Engr-in-Charge.
S&F in replacement water level switch of washer cum extractor 60 Kg capacity of existing size and make complete all as specified and directed by Engr-in-Charge.
S&F in replacement steam flexible pipe with metal cladding of standard size and length of washer cum extractor 60 Kg capacity of existing size and make complete all as specified and directed by Engr-in-Charge.
S&F in replacement B/F actuator valve 2' of washer cum extractor 60 Kg capacity complete all as specified and directed by Engr-in-Charge.
S&F in replacement B/F actuator valve 4' of washer cum extractor 60 Kg capacity complete all as specified and directed by Engr-in-Charge.
S&F in replacement door gasket of washer cum extractor 60 Kg capacity of existing size and make complete all as specified and directed by Engr-in-Charge.
M&L for repair of VFD 25 HP of washer cum extractor 60 Kg capacity including replacement of defective parts/ circuit plate including electrical connection complete all as specified and directed by Engr-in-Charge.
M&L for repair of control circuit plate and display controller of washer cum extractor 60 Kg capacity including replacement of defective parts of circuit plate including electrical connection complete all as specified and directed by Engr-in-Charge.
S&F in replacement FRL of flat bed ironner complete all as specified and directed by Engr-in-Charge.
S&F in replacement of V-Belt of suitable size and make of flat bed ironner complete all as specified and directed by Engr-in-Charge.
S&F in replacement of PVC pneumatic pipe including fitting complete all as specified and directed by Engr-in-Charge.
S&F in replacement of VFD 7.5 Hp of flat bed ironner complete all as specified and directed by Engr-in-Charge.
M&L for replacement cloth and covers suitable for Flat Work Ironer Machine complete including anchoring iron rod clip complete all as specified and directed by Engr-in-Charge.
M&L for replacement of conveyor belts with hook & pin suitable for Flat Work Ironer Machine complete all as specified and directed by Engr-in-Charge.
Supply and fixing, in replacement of guide tape suitable for Flat Work Ironer Machine complete all as specified and directed by Engr-in-Charge.
Supply only, in replacement of main bearing set roller suitable for Flat Work Ironer Machine complete all as specified and directed by Engr-in-Charge.
M & L padding for Flat belt Iron work 100% polyester fiber with a higher temprature resistance sutable for long roller and working more than 2500 hrs all as specified and directed by Engr-in-Charge.
S&F in replacement of chain sproket set of flat work ironner complete all as specified and directed by Engr-in-Charge.
S&F in replacement of chain of flat work ironner complete all as specified and directed by Engr-in-Charge.
S&F in replacement of temperature controller of flat work ironner complete all as specified and directed by Engr-in-Charge.
S&F in replacement of pneumatic cylinder for chest movement of existing size and make of flat work ironner complete all as specified and directed by Engr-in-Charge.
S&F in replacement of solenoid valve of existing size and make of flat work ironner complete all as specified and directed by Engr-in-Charge.
S&F in replacement of steam trap of existing size and make of flat work ironner complete all as specified and directed by Engr-in-Charge.
Supply only, in replacement of SS flexible steam inlet pipe of existing size suitable for Flat bed Press complete all as specified and directed by Engr-in-Charge.
Supply only, in replacement of white nipples suitable for Flat bed Press complete all as specified and directed by Engr-in-Charge.
S&F in repair spring for flat bed press complete all as per existing make and type complete all as specified and directed by Engr-in-Charge.
Supply and fix Drum shaft (Big) suitable for 50/60 KG Dry Tumbler as per existing shape and size including taking down old U/S one complete all as specified and directed by Engr-in-Charge.
Supply and fix Belt driven shaft (Small) suitable for 50/60 KG Dry Tumbler as per existing shape and size including taking down old U/S one complete all as specified and directed by Engr-in-Charge.
Supply only, in replacement of Steam Heating Coil having Copper Tube with Aluminium Fins suitable for Drying Tumblers of 50/60 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply only, in replacement of V-belt of existing size suitable for Drying Tumblers of 50/60 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply only, in replacement of steam trap suitable for Drying Tumblers of 50/60 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply only, in replacement of main drive bearing (2210) alongwith sleeves suitable for Drying Tumblers of 50/60 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply only, in replacement of idler drive bearing (2213) alongwith indler sleeves suitable for Drying Tumblers of 60 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply only, in replacement of Door Latches for lint screen suitable for Drying Tumblers of 60 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply only, in replacement of door limit switch suitable for Drying Tumblers of 60 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply only, in replacement of Timer 0-60 sec time delay suitable for Drying Tumblers of 60 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply only, in replacement of timer rev-fwd action suitable for Drying Tumblers of 60 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply only, in replacement of Digital temperature controller suitable for Drying Tumblers of 60 Kg capacity / flat bed press complete all as specified and directed by Engr-in-Charge.
Supply only, in replacement of main drive bearing alongwith sleeves suitable for Hydro extractor 25 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply only, in replacement of, transformer of 15 Amp capacity suitable for Hydro Extractor of 25 Kg capacity complete all as specified and directed by Engr-in-Charge. Make: As per existing sample.
Supply only, in replacement of Buffer suitable for 25 Kg Hydro extractor complete all as specified and directed by Engr-in-Charge. Make: As per existing sample.
Supply only, in replacement of Oil seal suitable for 25 Kg Hydro extractor complete all as specified and directed by Engr-in-Charge.
Supply only, in replacement of Limit switch suitable for 25 Kg Hydro extractor complete all as specified and directed by Engr-in-Charge.
Supply only, in replacement of Spring suitable for 25 Kg Hydro extractor (Make : Stefab) complete all as specified and directed by Engr-in-Charge. Make: As per existing sample.
S&F in replacement rectifier and element for hydro extractor complete all as specified and directed by Engr-in-Charge.
S&F in replacement of FRL of Flat bed press complete all as specified and directed by Engr-in-Charge.
M&L for replacement of cushion cloth/canvas set of flat bed press on top and bottom portion of press complete all as specified and directed by Engr-in-Charge.
S&F in replacement of SS Flexible pipe of existing size and length of Flat bed press complete all as specified and directed by Engr-in-Charge.
S&F in replacement of pneumatic cylinder of existing size of Flat bed press complete all as specified and directed by Engr-in-Charge.
S&F in replacement of spring of existing size of Flat bed press complete all as specified and directed by Engr-in-Charge.
S&F in replacement of temperature controller of Flat bed press complete all as specified and directed by Engr-in-Charge.
S&F in replacement of bearing set of existing size of Flat bed press complete all as specified and directed by Engr-in-Charge.
M&L for servicing of reciprocating air compressor including replacement of complete compressor oil, air filters, replacement of defective parts pressure switch, solenoid valve, FRL, Oil Air lube, NRV Seat, Spring NRV as applicable, filter assembly or any other defective part required to make compressor serviceable, including oiling/greasing, machine work, lathe work, welding work complete all as specified and directed by Engr-in-Charge. Note: 1. Any other defective part or part which is likely to fail and not present in schedule and need to be replaced for making machine serviceable for proper operation shall be replaced by contractor at no extra cost and cost of item is deemed to be included in quoted rate. 2. Cost of T&P and transportation is deemend to be incuded in quoted rates. 3. If any defect occur till next service during CA period then contractor will carry out repair and replace the defective part of machine at no extra cost.
Supply only limit switch suitable for Steam Boiler of 850 Kg /650 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply only Coil RXD 850 for 850 Kg/ HR boiler HSN/ SAC 84029020 ,part No PRXCL10002 Model : RXD/850 complete all as specified and directed by Engr-in-Charge.
Supply only Sequence controller suitable for Steam Boiler of 850 Kg/ 650 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply only Burner Rod suitable for Steam Boiler of 850 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply only metallic hose pipe 3/8" X 40 " size suitable for Steam Boiler of 850 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply only SS diffuser plate 132 mm suitable for Steam Boiler of 850 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply only Insulyte 7 Low Density Insulating Castable suitable for Steam Boiler of 850 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply only electronic timer suitable for Steam Boiler of 850 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply only thermocouple (TC) K type SS310 for Primary chamber suitable for Steam Boiler of 850 Kg /650 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply only safety relief value suitable for Steam Boiler of 850 Kg capacity complete all as specified and directed by Engr-in-Charge.
S & F PRV (Pressur reducing valve ) 50 mm bore including fixing arrangement , welding , brazing and taking down old unserviceable one all as specified and directed by Engr-in-Charge.
Supply and Fix Boiler Optimizer (Operation Performance Management for steem Plant) suitable for 860/660 Kg as per existing shape and size including taking down old unserviceable one all as specified and directed by Engr-in-Charge
Supply and Fix Boiler Economiser (Energy improving device) suitable for 860/660 Kg as per existing shape and size including taking down old unserviceable one all as specified and directed by Engr-in-Charge
Supply only Resin T-40 NA complete all as specified and directed by Engr-in-Charge.
S&F, in replacement, of RTD PT-100 temperature sensor output, complete all as specified and directed by Engr-in-Charge.
S&F, in replacement, of RTD temperature controller 0-1200ºC, K type input, complete all as specified and directed by Engr-in-Charge.
Supply only oil filter suitable for Steam Boiler of 650/ 850 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply only ignition electrode suitable for Steam Boiler of 850/600 Kg capacity complete all as specified and directed by Engr-in-Charge.
Supply only photo ignition electrode suitable for Steam Boiler of 850/600 Kg capacity complete all as specified and directed by Engr-in-Charge.
M&L for repair of Fuel pump AJ6AC suitable for Steam Boiler of 850/600 Kg capacity including dismantling of pump replacement of defective parts, oiling greasing and refitting in position complete all as specified and directed by Engr-in-Charge.
M&L for repair of triplex pump suitable for Steam Boiler of 850/600 Kg capacity including dismantling of pump replacement of defective parts, oiling greasing and refitting in position complete all as specified and directed by Engr-in-Charge.
Supply only Maxtreat 3220 solution for water softning plant complete all as specified and directed by Engr-in-Charge.
Supply only Maxclean 05 descaling chemical for boiler plant complete all as specified and directed by Engr-in-Charge.
Supply only Maxtreat 3004 solution for water softning plant complete all as specified and directed by Engr-in-Charge.
M&L for dismantling of electric driven horizontal induction motor of upto 30 HP capacity of any type and make, including disconnecting of electric connections, dismantling of motor, taking out the burnt windings, cleaning and washing of slots and rewinding the same with copper winding wire of existing gauge and quantity (as per original manufacturer design) including replacement of all damaged parts i. e. bearings, bush, thrust plate, thrust bearing, connector plate, insulating materials such as insulating sheets insulating paper (Class "F"), sealing compounds etc and reassembling the motor after varnishing, heating/drying, greasing of moving parts etc and reinstallation of the motor in original location, checking the alignment, making proper electric connection, testing for smooth operation, complete all as specified and directed by Engr-in-Charge. Note: Cost of T&P and transportation is included in quoted rates.
All as per srl item no 115 here-in-above but for 15 HP capacity, 3 ph, 415 volt, 50 Hz AC complete all as specified and directed by Engr-in-Charge.
All as per srl item no 115 here-in-above but for 7.5to 10.0 HP capacity, 3 ph, 415 volt, 50 Hz AC complete all as specified and directed by Engr-in-Charge.
All as per srl item no 115 here-in-above but for 3 HP capacity, 3 ph, 415 volt, 50 Hz AC complete all as specified and directed by Engr-in-Charge.
All as per srl item no 115 here-in-above but for 2 HP capacity, 3 ph, 415 volt, 50 Hz AC complete all as specified and directed by Engr-in-Charge.
Supply and lay MS pipe pipe in replacement 20 mm bore heavy grade with all fittings laid in floors or ffixed to walls and ceiling etc complete all as specified and directed by Engr-in-Charge.
All as per item No. 128 here-in-before but for pipe size of 25 mm dia complete all as specified and directed by Engr-in-Charge.
All as per item No.128- here-in-before but for pipe size of 32 mm dia complete all as specified and directed by Engr-in-Charge.
All as per item No.128 here-in-before but for pipe size of 40 mm dia complete all as specified and directed by Engr-in-Charge.
All as per item No. 128` here-in-before but for pipe size of 50 mm dia complete all as specified and directed by Engr-in-Charge.
All as per item No. 128 here-in-before but for pipe size of 65 mm dia complete all as specified and directed by Engr-in-Charge.
All as per item No. 128 here-in-before but for pipe size of 80 mm dia complete all as specified and directed by Engr-in-Charge.
All as per item No. 128 here-in-before but for pipe size of 100 mm dia complete all as specified and directed by Engr-in-Charge.
S&F in replacement Bronze Globe steam stop valve of size 50 mm dia as per ISI 778 ,class-2 gun metal body (IS-318LTB2), screwed in bonnet, out side screw and yoke type rising stem ,test pressure 500Psig. Hydraullic ,working pressure 250Psig at 450degree farenhite HSN CODE 84818030, complete all as specified and directed by Engr-in-Charge.
All as per srl item No 136 here-in-above but 80 mm dia size complete all as specified and directed by Engr-in-Charge.
All as per srl item No 136 here-in-above but 25 mm dia sizecomplete all as specified and directed by Engr-in-Charge.
S&F, in replacement, existing size caster wheel, swivel type, heavy duty, with supporting base plate bracket complete with nut and bolts etc of existing shape and size suitable for washroom trolley, complete all as specified and directed by Engr-in-Charge.
S&F in replacement, existing size caster wheel, fixed type, heavy duty, with supporting base plate bracket complete with nut and bolts etc of existing shape and size suitable for washroom trolley, complete all as specified and directed by Engr-in-Charge.
Supply only PVC container trolley as per existing size/ sample suitable for carry patiant cloths complete all as specified and directed by Engr-in-Charge.
Supply only crystal type salt of sodium chloride 25 Kg Bag for water softening plant @ 3 Kg/day complete all as specified and directed by Engr-in-Charge.
Supply & fixing in replacement, of MCB 40 to 63 Amp, TPN, 18 KA, C Curve, complete all as specified and directed by Engr-in-Charge.
Supply & fixing in replacement, of MCB 16 to 32 Amp, TPN , 18 KA, C Curve, complete all as specified and directed by Engr-in-Charge.
Supply & fixing in replacement, of MCCB 100 Amp, 3 pole, 36 KA, ICS = 100% ICU, with alongwith Spreader terminals and phase barriers, complete all as specified and directed by Engr-in-Charge.
All as per srl item No. 136 here-in-before but 36 KA 160 Amp capacity complete all as specified and directed by Engr-in-Charge.
Supply only, in replacement of Brake Timer 0-60 sec time delay suitable for 25 Kg Hydro extractor complete all as specified and directed by Engr-in-Charge.
S&F in replacement power contactor suitable for washer cum extractor 100 Kg including electrical connection complete all as specified and directed by Engr-in-Charge.
S&F in replacement MPD suitable for washer cum extractor 100 Kg including electrical connection complete all as specified and directed by Engr-in-Charge.
S&F in replacement rev-fwd timer suitable for washer cum extractor 100 Kg including electrical connection complete all as specified and directed by Engr-in-Charge.
S&F in replacement power contactor suitable for drying tumbler 50/60 Kg including electrical connection complete all as specified and directed by Engr-in-Charge.
S&F in replacement SPP suitable for drying tumbler 50/60 Kg including electrical connection complete all as specified and directed by Engr-in-Charge.
S&F in replacement steam/water ball valve of size 15 mm complete all as specified and directed by Engr-in-Charge.
S&F in replacement steam/water ball valve of size 20 mm complete all as specified and directed by Engr-in-Charge.
S&F in replacement steam/water ball valve of size 25 mm complete all as specified and directed by Engr-in-Charge.
S&F in replacement steam/water ball valve of size 50 mm complete all as specified and directed by Engr-in-Charge.
S&F in replacement of emergency stop switch complete all as specified and directed by Engr-in-Charge.
S&F in replacement of push button complete all as specified and directed by Engr-in-Charge.
S&F in replacement of LED indicator complete all as specified and directed by Engr-in-Charge.
S&F in replacement 0-20 s timer timer suitable for hrdro extractor 25 Kg including electrical connection complete all as specified and directed by Engr-in-Charge.
S&F in replacement power contactor suitable for hrdro extractor 25 Kg including electrical connection complete all as specified and directed by Engr-in-Charge.
S&F in replacement SPP suitable for hrdro extractor 25 Kg including electrical connection complete all as specified and directed by Engr-in-Charge.
S&F in replacement power contactor suitable for flat bed ironner including electrical connection complete all as specified and directed by Engr-in-Charge.
S&F in replacement SPP suitable for flat bed ironner including electrical connection complete all as specified and directed by Engr-in-Charge.
S&F in replacement overload relay suitable for flat bed ironner including electrical connection complete all as specified and directed by Engr-in-Charge.
S&F in replacement overload relay suitable for boiler including electrical connection complete all as specified and directed by Engr-in-Charge..
S&F in replacement power contactor suitable for boiler including electrical connection complete all as specified and directed.
S&F 2 H.P Sewage submersible pump STPM22 or equivalent 1 Ph 220 V AC supply complete all as specified and directed by Engr-in-Charge.
M&L for acrylic LED Glow Sign Board complete all as specified and directed by Engr-in-Charge.
M&L for acrylic signange plate complete all as specified and directed by Engr-in-Charge.
Flint India (BID ID -3298308)
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .