REPAIR AND REPLACEMENT OF TILES FLOOR WALL PLASTERING PLUMBING FITTING JOINERY AND REPAIR TO TOILET AND KITCHEN IN CERTAIN MD OTM ACCN UNDER AGE BR I OF GE AF ADM AREA AT AF STATION AGRA

Amount

Taking down cement plaster on walls/ceiling of any description including racking out joints hacking for key, scrubbing down with water etc. and removing rubbish complete all as specified and directed.

M&L for rendering 15 mm thick on brick work or concrete surface in cement mortar 1:6 finished even & smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 using liquid WPC @ 200 ml per bag of cement finished even and smooth without using extra cement complete all as specified and directed. (Rate of Water proofing compound shall deemed to be included under this item).

M&L for rendering 10 mm thick on concrete surfaces of ceiling with CM (1:4) and finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new surface of wall and applying wall care putty minimum 1 mm thick, a coat primer and two coats of oil bound distemper complete all as specified and directed.

M&L for applying two coats of white wash on wall including preparation of new surface complete all as specified and directed.

Material and labour for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489-2004 alkali and fungal resistance, dirt resistance exterior emulsion paint of required shade (Company Depot tinted) with silicon addtitives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 ltr/10 Sqm etc on newly plastered surface of wall including preparation of surface complete all as specified.

M&L for applying two coats of cement base paint over a coat of alkali resistant primer on new surfaces of walls including preparation of surface complete all as specified and directed.

M&L for applying two coats of white wash on ceiling including preparation of new surface complete all as specified and directed.

M&L for washed stone grit plaster on exterior walls in two layers, under layer 12 mm thick in cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square meter, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings including taking down of old plaster complete all as specified and directed. Note : Making grooves(of uniform size 15 mm x 15 mm) shall be included in quoted rates.

M&L for cleaning of OHT exc 250 & n exc 500 ltrs internally by balling out of water/sludge from bottom of tank, removing all scale, dirt alleges and other growths from entire surface of tank and from mounts of circulating pipes by rubbing with wire brushes and by high pressure cleaning method with rotary sets with approved detergent and sucking all dirty water by vaccum cleaner, disinfecting the tank with approved chemical/ bleaching powder for making the surface bacteria free and cleaning with fresh water complete all as specified and directed

All as per item No. 11 above but OHT exc 500 & n exc 1000 ltrs

All as per item No. 11 above but OHT exc 1000 & n exc 2000 ltrs

S&F in repair tripple layer rotational moulded polyethylene water storage tanks 500 lts capacity (cylinderical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

S&F in repair tripple layer rotational moulded polyethylene water storage tanks 1000 lts capacity (cylinderical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

S&F in repair tripple layer rotational moulded polyethylene water storage tanks 2000 lts capacity (cylinderical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

S&F in repair ball valve 20 mm bore high presure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight not less than 210 grams) complete all as specified and directed.

S&F in repair 25 mm bore gun metal gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

Supply, fixing, laying & testing 15 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors and testing including taking down existing GI tubing complete all as specified and directed.

Taking down and refixing of 15 mm bore GI Steel tubings including new or old fittings complete all as specified and directed.

Supply, fixing, laying & testing 20 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors and testing including taking down existing GI tubing complete all as specified and directed.

Taking down and refixing of 20 mm bore GI Steel tubings including new or old fittings complete all as specified and directed.

Cutting existing GI pipes, 20 mm bore, laid in position for taking out branch connection by inserting new Tee and coller etc. complete all as specified and directed.

S&F in repair vitreous china squatting pan Orissa pattern size 580 x 440 mm white with front or back inlet, integral foot rest including connection to trap and flushing pipe, anti syphonage and providing cement concrete bedding complete all as specified and directed.

S&F in repair Viterous China wash down water closet pan (pedestal pattern) with 'P' or 'S' trap, white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed.

S & F in repair plastic water closet seat cover, white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

S&F in repair health faucet (ABS body) mild steel chromium plated suitable for 15 mm dia pipe superior quality with 1.25 m long flexible pipe and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F in repair 10 Ltrs capacity, PVC valveless, syphonic action type, low level flushing cistern, white, with inlet, ball valve, float and handle complete with all internal accessories and fixed to wall, PVC flush pipe 32 mm dia 90 cm long fixed properly to inlet of WC and making good to disturbed surfaces of wall or floor complete all as specified and directed.

S&F in repair vitreous china wash hand basin white flat back size 550x400 mm including two Nos angle iron brackets and 32 mm dia CP waste coupling and one number pillar tap, CP, fancy type, cast copper alloy complete all as specified and directed.

S&F in repair chromium plated brass shower rose 125 mm dia with or without swival joints, with CP long shank including fixing to 15 mm dia pipe or union all as specified.

S&F in repair long body bib taps, cast copper alloy, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and directed.

S&F in repair PVC connection 450 mm long suitable for 15 mm GI pipe with two PTMT nuts & rubber washers complete all as specified and directed.

S&F in repair 15 mm dia chromium plated brass wall mixture for mixing hot and cold water sutable for 15 mm bore GI pipe complete all as specified and directed.

S&F in repair stop valve/angle valve 15 mm nominal bore quarter turn, cast copper alloy, fancy type, chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified and directed.

S&F in repair pillar taps, cast copper alloy with capston heads, fancy type, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed.

S&F in repair 20 mm dia brass chromium plated tubular towel rail, D type, 60 cm long between flanges fixed with rawl plug complete all as specified and directed.

Demolition of cement concrete unreinforced in ground floors and pavings n.exc. 15 cm thickness(below or above ground level) complete all as specified and directed.

M&L for cutting holes into or through cement concrete slabs, chajjas etc. of superficial area n. exc. 100 Sqcm for inserting pipe as in sunken portion to facilitate efficient drainage including packing with PCC 1:3:6 and making good to match existing surface complete all as specified and directed.

S&F 50 mm GI pipe, medium grade in isolated length of 400 mm long inserted into wall surface as in water drainage spout complete all as specified and directed.

M& L for rendering wall, floor as in sunken portion 15 mm thick in two layers of 10 + 5 mm in CM 1:6 mixed with Pidi Proof 101 LW(+) of Dr fixit (Pidilite) or equivalant intergral water proofing admixture @ 200 ml/bag of cement over two coats of super latex 302 of Dr fixit (Pidilite) or equuilvalant in the ratio (1:4:7), (one part super latex, 4 part water and 7 parts of cement) @ 1.5 Kg of homogenious mixture /Sqm in two coats and finish the surface even and smooth (without using extra cement) complete all as specified and directed. Note:- Pidi proof and super latex to be measured and paid separately as supply only.

Supply only Pidi proof 101 LW (+) of Dr Fixit (Pidilite) or equivalent of make Latex/ CICO No. 1/ Fosroc (India) Ltd.

Supply only super latex 302 of Dr Fixit (Pidilite) or equivalent of make Latex/ CICO No. 1/ Fosroc (India) Ltd.

M&L for plain cement concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) filling as in sunken portion including sub base of under floors complete all as specified and directed.

M&L for 40 mm thick cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in sunken floor for correction of slope/levelling etc. complete all as specified and as directed.

S&F in repair SGSW 'P' trap 100 mm bore, setting the trap and pan in 150 mm thick all around cement concrete 1:2:4, complete all as specified and directed.

S&F in repair cast iron floor trap, 75 mm bore with stainless steel grating including jointing to waste pipes and fixed in cement concrete 1:2:4 type B-1 complete all as specified and directed.

S&F in repair 75 mm dia PVC (SWR) multi floor trap, with stainless steel grating including jointing to waste pipe with solvent cement and fixed in cement concrete 1:2:4 type B1(using 20 mm graded stone aggregate) complete all as specified and directed.

S&F in repair 100 mm bore CI bend (any radius), diminishing pieces or tapers (large bore measured) with oval access door complete all as specified and directed.

S&F in repair 75 mm bore CI bend (any radius), diminishing pieces or tapers (large bore measured) with oval access door complete all as specified and directed.

S&F in repair cast iron branch pieces single (equal or unequal) ordinary or inverted, spigot or socket type or with parallel branches suitable for 100 mm bore pipe complete all as specified and directed.

S&F in repair cast iron branch pieces single (equal or unequal) ordinary or inverted, spigot or socket type or with parallel branches suitable for 75 mm bore pipe complete all as specified and directed.

S&F in repair CI cowl 100 mm bore fixed with cement joint complete all as specified and directed.

S&F in repair CI cowl 75 mm bore fixed with cement joint complete all as specified and directed.

S&F in repair cast iron nahani trap, 100 mm bore with stainless steel grating including jointing to waste pipes and fixed in cement concrete 1:2:4 type B-1 complete all as specified and directed.

S&F in repair cast iron sand cast soil, waste and vent pipe 100 mm bore in any length with or with out ears with cement joints fixed to wall with MS clamps complete all as specified

S&F in repair cast iron sand cast soil, waste and vent pipe 75 mm bore in any length with or with out ears with cement joints fixed to wall with MS clamps complete all as specified

Taking down and refixing cast iron sand cast soil, waste and vent pipe 100 mm bore in any length with or with out ears with cement joints fixed to wall with MS clamps complete all as specified

S&F in repair PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive laid in trenches or in floors complete all as specified and directed.

S&F in repair PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints and laid on floors or fixed to walls with PVC clamps complete all as specified and directed.

S&F PVC(SWR) bends 110 mm dia complete all as specified and directed.

S&F PVC(SWR) 110 mm dia branch pieces single (single Y) equal or unequal or TEE junction with access door complete all as specified and directed.

S&F PVC (SWR) vent cowl 110 mm bore complete all as specified and directed.

S&F in repair PVC (SWR) pipe 75 mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive laid in trenches or in floors complete all as specified and directed.

S&F in repair PVC (SWR) pipe 75 mm bore, single socketed, in any length with rubber ring joints and laid on floors or fixed to walls with PVC clamps complete all as specified and directed.

S&F PVC(SWR) bends 75 mm dia complete all as specified and directed.

S&F PVC(SWR) 75 mm dia branch pieces single (single Y) equal or unequal or TEE junction with access door complete all as specified and directed.

S&F PVC (SWR) vent cowl 75 mm bore complete all as specified and directed.

S&F 75 mm dia PVC (SWR) floor trap including jointing to waste pipe with solvent cement and fixed in cement concrete 1:2:4 type B1(using 20 mm graded stone aggregate) complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in the shelves and the like including demolition of existing RCC slab complete all as specified and directed.

Use and waste Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) complete all as specified and as directed.

M&L for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square or rectangular) area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes and dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick joint less (square or rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes and dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

M&L for glazed ceramic designer coloured tiles of size 450 x 350 x 6-7 mm thick in vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface with & including rendering 10 mm thick in cement mortar 1:4 on other than fair faces of brick wall finished rough to fix tiles and dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 300 x 200 x 6-7 mm thick in vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface with & including rendering 10 mm thick in cement mortar 1:4 on other than fair faces of brick wall finished rough to fix tiles and dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

M&L for granite stone 18-20 mm thick (of any type) glazed (table rubbed and polished) fixed as in skirting, steps, jambs, pillars, window cills, cooking plateform and the like set in cement mortar 1:4 and pointed with white cement (1:2) using marble dust with admixture of pigment to match with and including screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:4 including demolition of existing slab complete all as specified and directed.

M&L for machine cut kota stone slab of size not less than 550 x 550 mm (except where lesser size required) as in flooring or in trades of steps 20 to 25 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing, rounding of edges and mirror finish polishing with & including screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:4 for laying floor finishes including demolition of existing stone complete all as specified and directed

S&F in repair sink without draining board made of stainless steel 1mm thick with plugs, washers, waste pipe and coupling overall size 495 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F in repair sink with draining board made of stainless steel 1mm thick with plugs, washers, waste pipe and coupling overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F in repair 1 mm thick stainless steel plate rack over all size 900 x 600 x 250 mm of standard pattern and make as approved by GE complete all as directed.

Taking down anodised aluminium window side hung shutter and refixing in the same opening after repairing including necessary jointing cleats, Glazing clips, rubber packing, screws etc & with existing anodised aluminium snap beading, replacing glass/ wirecloth if required complete all as specified and directed. Note:- Glass/ wirecloth/ builders hardware/ aluminium section replaced shall be measured and paid seperately.

Supply only aluminium section for door, window, ventilator etc of any thickness and size to match existing complete all as specified and directed.

Supply only roller for sliding aluminium window complete all as specified and directed.

Supply only 0.36 mm dia stainless steel wire cloth with average width of aperature 1.40 mm complete all as specified and directed.

Supply only 4 mm thick sheet glass ordinary quality and fixing to aluminium door/ window not exceeding 0.50 Sqm in each pane complete all as specified and directed.

Taking down Chowkats or frames with shutter (without taking off shutters from the frame) n. exc. 1.50 sqm each complete all as specified and directed.

S&F factory made solid PVC door frame of size 50mmx 47mm made out of 5 mm single side prelaminated PVC sheet & edges painted to match with prelaminated sheet and fixed with screws and rawl plugs complete all as specified and directed.

S&F Factory made solid PVC moulded door shutter with wood free EPS 28 to 30 mm thick(stiles), with 2, 4 or 6 raised panel design with 2mm thick moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, with particle board core, supplying & fixing in frame at site as per specifications & drawings shown in section 8 of SSR Part II complete all as directed.

S&F 100 mm size stainless steel, butt hinges, medium weight ISI marked and fixed with screws complete all as specified and directed.

S&F aluminium anodised barrel tower bolt of extruded section 150 mm long ISI marked and fixed complete all as specified and directed.

Taking down Chowkats or frames with shutter (without taking off shutters from the frame) exc. 1.50 sqm and n. exc. 4.00 sqm each complete all as specified and directed.

M&L for 2nd class hard wood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed.

M&L for 35 mm thick factory made, plain framed, panelled shutters (two panels), with lock rail and panels of 9 mm thick BWP commercial ply or of venered particle board 12 mm thick with commercial veneering on both faces with rails and style of 2nd class hard wood. The size of rail and stile as per IS : 1003 (part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L for 2nd class hard wood glazed and skeleton shutters 35 mm thick, open rebated and prepared to receive glass, gauze, etc. divided into squared, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.24 (a); supplied and fitted to chowkhats complete all as specified and directed.

S&F 30 mm thick flush shutters, solid core construction, with block board core and one face plywood face panels, commercial type, other face covered with decorative face veneer with lipping/frame to match shutter complete all as specified and directed.

M&L mild steel work as hold fasts and similar small articles conforming to Fe-290, Gde E-165 complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood or wood based materials of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F 0.36 mm dia stainless steel wire cloth with average width of aperature 1.40 mm and fixed with stainless steel wire staples or moulded beading complete all as specified and directed.

S&F aluminum alloy anodized sliding door bolt 250 mm long with hasp and staple (bolt type) and fixing clip of sheet and cast in extruded section and fixing bolts and sliding bolt of extruded section complete all as directed and directed.

S&F aluminium anodised barrel tower bolt of extruded section 200 mm long ISI marked and fixed complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm complete all as specified and directed.

S&F alumunium handle, fabricated type, anodised 150 mm long ISI marked complete all as specified and directed.

S&F 100 mm size mild steel butt hinges, ISI marked, medium weight, cold rolled and fixed with screws/welded to frame complete all as specified and directed.

S&F 300 mm, mild steel rat tail rod pattern spring including roller and roller plate of flat iron 40 x 3 mm, 75 mm long fixed to stone/ concrete/ wooden/ metal chowkhat with screws or welding complete all as directed.

S&F 3 mm thick sheet glass ordinary quality and fixing with wooden beads or oil putty and provsion of glazing pins in squares not exceeding 0.50 Sqm in each pane including hacking out old broken glass of any description and thickness from wooden/steel frames fixed with wooden beads/putty and complete all as specified and directed.

S&F figured glass, 3 mm thick, pin head type and glazing with oil putty in squares exc. 0.50 Sqm in each pane including hacking out old broken glass of any description and thickness from wooden/steel frames fixed with wooden beads/putty and complete all as specified and directed.

Resecuring or easing and adjusting shutters of any description not exc. 1 Sqm each without taking down shutters complete all as specified and directed.

Resecuring or easing and adjusting shutters of any description exc. 1 Sqm but not exc. 2 Sqm each without taking down shutters complete all as specified and directed.

M&L for Anodised aluminium grill (any colour and thickness of coating not less than 50 micron) of approved design/pattern, with opening size 101.6 x 63.5 mm (4" x 2.5") and approximate wt 1.345 Kg/ Sqm, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and as directed.

S&F powder coated (any colour and thickness of coating not less than 50 micron) aluminium sliding window shutters suitable to fix in two/three track rail, including necessary aluminium fittings such as joining cleats, glazing clips, rubber packing, aluminium snap beading, screws, 5 mm thick tinted glass in two shutters and 0.36 mm dia stainless steel wire cloth with average width of aperature 1.40 mm with required EPDM rubber/ neoprene gasket etc. with extruded built up standard tubular sections/ appropriate Z sections, incl all fittings/ fixtures such as roller, locking arrangement, handle etc. complete all as specified and directed. Following sections of Jindal make or equivalent sections in Hindalco/ Indal/ Nalco shall be followed:- Three Track Bottom - Section No. 20957 Three track top/ vertical - Section No. 20958 Handle - Section No. 20606 Interlocking - Section No. 20605 Top/Bottom/Sides of shutters - Section No. 20604

S&F powder coated (any colour and thickness of coating not less than 50 micron) aluminium ventilator, fixed type, frame made of Section 63.50 x 38.10 x 1.29 mm, 5 mm thick frosted glass in lower 55% portion and 0.36 mm dia stainless steel wire cloth with average width of aperature 1.40 mm in upper 45 % portion with required EPDM rubber/ neoprene gasket etc. with extruded built up standard tubular sections/ appropriate Z sections complete all as specified and directed. Make : Jindal/ Indal/ Hindalco/ Nalco

GIRENDRA SINGH AND CO

saroj constructions

deva engineers

M/s M S Sharma and Co.

Shiv Krishan Associates

M/S SINGH ELECTRIC CO

M/s Shiv Builders