CA NOCWE/FZR-40/2019-20 SPECIAL REPAIR TO BLDG. NO P-120/1 TO P-120/8 (08 X QTRS) JCOS MD ACCN OF EME BN AT F ZONE UNDER GE (WEST) FEROZEPUR CANTT

Amount

Dismantling of brick tiles single layer jointed & pointed in cement mortar including removal of grass including roots, vegetation, complete all as specified.

Demolition of mud phuska in roofs, any thickness, including leeping plaster (whether full thickness removed or only a part thereof) complete all as specified.

M&L for screed bedding 10 mm in cement mortar (1:4) concrete surfaces of roof, mixed with WPC (WPC shall be measured and paid seaparately), finished even and smooth without using extra cement etc, complete all as specified.

Supply only integral water proofing compound ISI marked, complete all as specified.

M&L for cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc, and making good, cutting exc 10 cm not exc 20 cm girth, complete all as specified.

M&L for laying APP based polymeric membrane 3 mm thick with minimum weight not less than 3 kg/sqm, reinforced with non woven polyster fabric (wt. not less than 160 gms/sqm) torching Joints/overlaps with a propane or a butane gas torch, laid with a minimum overlap of 150mm with thermo fusable finish laid/bonded over a coat of hot blown bitumen 85/25 @ 1.20kg/sqm, over forced application bitumen primer @ 0.30 liters per sqm, including preparation of plastered surfaces of roof including parapet, complete all as specified and as directed. Note:- The water proofing treatment shall be got carried out by manufacturer or their authorised applicator.

M&L for 40mm thick PCC type B-1 (1:2:4) using 20mm graded stone aggregate for bases of floor, complete all as specified.

M&L for cement concrete tiles of size 20cmx20cmx22 mm thick as in roof set and jointed in neat cement slurry and pointed in grey cement no pigment laid over 15 mm thick screed in cement mortar (1:6) mixed with WPC, joints frouted and flush pointed in CM (1:3) mixed with 5% of crude oil weight of cement, complete all as specified.

M&L for preparation of roof surface and applying two coats of sloar reflective bituminious aluminium paint @ 0.10 Kg/Sqm over bituminious membrane, complete all as specified and directed.

M&L Cement concrete (1:2:4) type B-1 (20 mm graded stone aggregate) as in roof kerbs, bed blocks, benching, coping etc including form work, weathering, slightly rounded or chamfered complete all as specified.

Taking down cement plaster from brick walls of any description, racking out joints, hacking for key, scrubbing down with water etc, complete all as specified.

M&L for Rendering 15 mm thick in cement mortar (1:4) on any face of brick walls or concrete surfaces, mixed with WPC (WPC shall be measured and paid seaparately), finished even and smooth without using extra cement, complete all as specified.

M&L for Rendering 10 mm thick in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement, complete all as specified.

M&L Rendering 5 mm thick in cement mortar (1:3) on ceiling concrete surfaces finished even and smooth without using extra cement, complete all as specified.

M&L for providing and injecting emulsion for post construction anti-termite treatment of soil under existing floors using emulsion @one litre per hole 300mm apart inclduing drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors, complete all as specified & directed.

M&L providing and injecting emulsion along the external wall below concrete or masonary apron using chemical emulsion @2.25 litres per linear metre including drilling and plugging holes etc in apron. complete all as specified & directed.

M&L for removing loose and broken concrete by chiseling/picking etc upto a depth of 20 to 40mm from floor/roof slab and similar structural members cutting edges cleaning the dismantled portion with wire brushes etc to remove dust, dirt and other foreign particles etc and washing with clean water with pressure and removal of debries to a distance not exc 50m complete all as specified and directed by Engineer-in-Charge, including necessary scaffolding etc complete.

M&L for applying one coat of anti corrosive primer as per manufacturers insturctions to exposed old and new reinforcement to the full circumferences and length of bars to form unbroken 40micron thick film in the area prepared vide item no 17 above complete all as specified and directed by Eng-in-Charge.

M&L for applying one coat epoxybonding agent as per manufacturers insturction to old concrete surfaces prepared as per item (18) above all as specified and directed by Eng-in-Charge in surfaces of columns, beams, and similar structural members prepared as per item (18) above including use and waste of water tight form work to facilitate pouring of micro concrete complete all as specified and directed by Engineer-in-Charge.

M&L for application of high build polymer modified to ceiling with cement mortar Plaster (1: 3) with SBR @ 4 ltr per bag of cement applied as per manufacturer's instrutions, complete all as specified and directed .

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified.

M&L for Non skid Ceramic coloured ( colour and shade as approved) tiles,any shape, 7mm to 8 mm thick area of each tile exc. 0.11 sqm and not exc 0.18 sqm as in flooring set and jointed in neat cement slurry and pointed in white cement with pigment to match the colour of tiles laid over & including 15 mm thick screed in cement mortar (1:6) laid over, complete all as specified.

All as per Item No-22, but as on vertical surfaces such as skirting/dado over and including 10 mm thick rendering in cement mortar (1:4), complete all as specified.

M&L for Glazed ceramic tiles, coloured (colour & shade as approved), of size 300x200x7 mm thick on vertical surfaces such as in skirting/dado etc set and jointed in cement slurry and pointed in white cement with pigment to match the colour of tiles, laid over & including 10 mm thick rendering in cement mortar (1:4), complete all as specified.

Demolition of stone slabs and tiles of any description or thickness in floor,aprons, etc laid in bedded and pinted in any surfaces complete all as specified and directed.

M&L for Kota stone slabs, 20mm to 25mm thick, machine cut as in flooring of size not less than 0.25 Square metre each, set and jointed in cement slurry and pointed in cement mixed with pigment to match the shade of slab laid over & including screed bed of 20 mm thick in cement mortar (1:6) including rubbing, cutting and polishing (mirror type) complete all as specified.

S&F Kota stone slabs, 20 mm thick, machine cut as in shelf, skirting,steps,dado,pillars etc, set and jointed in cement slurry and pointed in cement mixed with pigment to match the shade of slab laid over & including rendering coat of 10 mm thick in cement mortar (1:4) including rubbing, cutting and polishing, complete all as specified.

M&L for green marble slab, 18 mm thick of size not less than 1.00 square metre each, as in cooking platforms, steps, jambs, pillars, window cills and like, set and bedded in grey cement slurry over & including 15 mm thick screed in cement mortar (1:4) and pointed in white cement with admixture of pigment to match the shade of marble (mirror type polished) complete all as specified.

Demolition of brick work built in cement mortar of any specification and in any position complete all as specified.

M&L for Brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius, complete all as specified.

All as per item 30 hereinbefore but using old bricks retrieved from demolition under item 29 hereinbefore including cleaning and removal of mortar from old bricks complete all as specified.

M&L for Taking down wooden/steel chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Square metre each, complete all as specified.

All as per item No 32 herein before but size exceeding 1.5 Square metre and not exceeding 4 Square metre each.

Taking down door shutter of any description, exc 1 Sqm but not exceeding 2 sqm each and removing to stores, complete all as specified.

Taking down door shutter of any description, exc 1 Sqm but not exceeding 2 sqm each and refixing in the same opening, complete all as specified.

M&L Factory made box type side hung steel window with pintal hinges & 2 Nos 150 mm mild steel tower bolts to each shutter, steel handle and with/wihout glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07.

S&F Factory made box type steel ventilator side/top hung with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified.

M&L for Cutting holes in brick walls in cement mortar for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required, depth of embeded portion of hold fast exc half bricks but not exc one brick built in cement mortar or cement lime mortar and stone walls built in lime mortar complete all as specified.

S&F Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work, complete all as specified.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified.

M&L for forming jambs etc built in cement mortor 1:6 to openings incl cutting toothing and properly bonding into to old work also facing ,jointoing and pointing to match to existing work complete all as specified.

S&F Factory made pressed steel frames made of 1.25 mm thick MS sheet of profile 105 mm X 60 mm for door and window frames with one or more rebates including lock strike plate, shock absorber, 20 mm dia 60 mm long MS conduit for housing of a drop bolt,hinges, hold fasts/lugs etc, treating of internal surfaces of chowkhats with coal tar or black paint including hold fasts/lugs etc complete all as specified.

S&F Factory made pressed steel frames made of 1.25 mm thick MS sheet of profile 125 mm X 60 mm for door and window frames with one or more rebates including lock strike plate, shock absorber, 20 mm dia 60 mm long MS conduit for housing of a drop bolt,hinges, hold fasts/lugs etc, treating of internal surfaces of chowkhats with coal tar or black paint including hold fasts/lugs etc complete all as specified.

All as per item No 44 herein before but size 75 X 50mm single rebate, complete all as specified.

S&F Factory made 35 mm thick,2nd class hard wood (Hollock), glazed and skeleton shutters open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitered beads for securing glass/gauge etc for doors, size of members as specified in clause 8.24 (a) of MES Schedule Part-I Section-8, complete all as specified.

S&F Factory made, 35mm thick, 2nd class hard wood (Hollock), plain framed, panelled shutters, any number of panels, panels shall be of 9 mm thick B.W.P. commercial ply or 12mm thick BWR grade veneered particle board medium density, wood particle board with commercial face veneers, size of members as specified in clause 8.24(a) of MES Schedule Part-I section-8 complete all as specified.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples, complete all as specified .

S&F in repair galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples, complete all as specified .

S&F 3mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads (supplied alongwith shutters), in squares n.exc 0.50 Sqm complete all as specified.

S&F 3 mm Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane, complete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified.

M&L in repair, 2nd class soft wood fillets, sectional area n.exc. 3 sqcm, rectangular in section, wrought finished, fixed with PVC rawl plug & steel screw complete all as specified.

S&F Small articles of 1st class hard wood (hollock, sheesham wood may be used without financial adjustment), such as hinge blocks, door and window stops, articles not exceeding 200 cubic centimeter each and fixed with steel screws, complete all as specified.

Dismantling boarding, any description,and in any position fixed with nails in any position, complete all as specified.

S&F factory made PVC cup boards/shelfs/partition of required size consisting of panel of 18mm thick Celuka PVC ply and for supporting the hold of shelf/partition and shall provided 3 edge in size 40x18mm as per required length. The front side of the edge visible in front of the shelf/partition to be edge lipped by the 18mmx1mm thick PVC sheet using solvent cement etc, complete all as specified.

S&F Hasp and staple of aluminium anodized, safety type, 100mm long, fixed with screws complete all as specified.

S&F anodized aluminium alloy handle, fabricated type 125 mm long and fixed with steel screws complete all as specified.

S&F continious piano hinges mild steel, bright finish or electrogalvanised width of flap 25mm, complete all a specified.

S&F in repairs, 40 mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished, complete all as specified.

S&F in repairs, magnet catchment of specified shape and size for cupboard selves in kitchen etc, complete all as specified.

S&F Factory made solid PVC door frame of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube, complete all as specified in MES Schedule Part-I (2009),including making good jambs in CM (1:4) with finishes to match with existing, complete all as per specification & drawing.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site ,complete all as per specification in MES Schedule Part-I (2009) & drawing.

S&F anodized aluminium alloy barrel tower bolts, 200 mm long and fixed with steel screws complete all as specified.

S&F 100 mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, complete all as specified.

S&F 150mm long pressed handles, extruded aluminium alloy fixed with steel screws, complete all as specified.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified.

S&F 300 mm mild steel helical door spring including roller and roller plate complete all as specified.

M&L for welding in running for thickness of metal to be welded n.exc 6mm, complete all as specified.

Taking up or down existing steel water tubing, 15 mm bore alongwith connections fixed/laid in any situation, complete all as specified

Taking up or down existing steel water tubing, 20 mm bore alongwith connections fixed/laid in any situation, complete all as specified.

S&F Galvanised steel water tubing, 15 mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors including cutting and making good, complete all as specified.

S&F Galvanised steel water tubing, 20 mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors including cutting and making good, complete all as specified.

Re-Fixing only, steel water tubing, 15mm bore and connections in new or old position using new fittings fixing to wall/ceiling or laid in floors complete all as specified.

Re-Fixing only, steel water tubing, 20mm bore and connections in new or old position using new fittings fixing to wall/ceiling or laid in floors, complete all as specified.

S&F in repair 500 litres capacity rotational moulded, triple layer polythene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position on roofs including fittings, complete all as specified.

S&F in repair 20mm bore PTMT ball valve high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule, complete all as specified.

S & F in repiar, 1mm thick stainless steel sink with drainage board, plugs, washers, PVC waste pipe, Union,CP coupling & cantilever brackets embedded in cement and sand mortar in wall, overall size of sink 915mm x 460mm, bowl size 410mm x 330mm x 160mm complete all as specified.

S&F Stainless steel plate rack of standard pattern & of size 900 x 900 x 250 mm thickness of stainless steel sheet shall be 0.56 mm & grade of sheet shall be 304 AISI including fixing to wall with 4 Nos 50mm screws & PVC rawl plugs complete all as specified and directed.

S&F in repairs PVC connection 15mm size with brass nuts on both ends, 450mm long with PTMT nuts complete all as specified.

S&F soap dish of PTMT fixed with and including Chromium plated brass screws and rawl plugs. (Minimum weight 105gms), complete all as specified.

S&F in repair Vitreous china white squatting pan orrissa pattern of size 580mm x 440mm with integral foot rests including necessary lime concrete and 100 mm bore cast iron ‘P’ trap with 550 to 600 mm long neck for connecting WC to branch piece with cement joints, complete all as specified.

S&F in repairs PVC syphonic action type low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, 32 mm PVC flush pipe and necessary fixing arrangements and connecting to water pipe, complete all as specified .

S&F in repairs wash hand basin, flat back 550mm x 400mm vitreous china (white) including PTMT waste coupling/fittings, 32 mm bore size, waste pipe, PVC, 32mm bore, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing , complete all as specified.

S&F Mild steel curtain rod PVC powder coated with fixing side brackets, end cups, rings @ 10 Nos per RM and fixed with PVC rawl plugs & steel screws as in repairs complete all as specified.

Dismantling CI pipe alongwith fittings of 50/75/100mm bore, below or above ground level or laid in floors, jointed in cement mortar and taking out complete all as specified.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc, including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories), complete all as specified.

S&F in repairs, 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls including distance pieces and incld stack clamps with nuts & bolts, complete all as specified.

All as per item no 89, but laid in trenches or in floors, complete all as specified.

S&F in repairs 110 mm bore PVC (SWR) bends/shoe and provided with access door any radius fixed to walls including distance pieces and stack clamps, including making good around complete all as specified.

S&F in repairs 110 mm bore PVC (SWR) vent cowl, complete all as specified.

S&F 110mm bore, PVC (SWR) branch piece, single (single T) equal or unequal with access door complete all as specified.

S&F in repairs, 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls including distance pieces and incld stack clamps with nuts & bolts, complete all as specified.

All as per item no 94, but laid in trenches or in floors, complete all as specified.

S&F in repairs 75 mm bore PVC (SWR) bends/shoe and provided with access door any radius fixed to walls including distance pieces and stack clamps, including making good around complete all as specified.

S&F 75mm bore, PVC (SWR) branch piece, single (single T) equal or unequal with access door complete all as specified.

M&L for 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified.

S&F in repair 15 mm bore bib tap of, fancy type chromium plated, screwed down, high pressure with crutch or butter fly handle, complete all as specified.

S&F in repair 15mm stop cock cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule fancy type chromium plated with long shank and cup (concealed type), complete all as specified.

S&F in repair 15mm stop cock cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule fancy type chromium plated with fancy type shank and cup, complete all as specified.

S&F in repair, tublar Towel Rail 60cm long 'D' type between flanges of chromium plated 20mm dia fixed to walls, complete all as specified.

S&F in repair Brass chromium plated shower roses 125mm size with or without swivel joints,with shower arm 15 mm dia, 195 mm long with bend of 45 degree with flange of CP brass, including fixing to steel pipe or union, complete all as specified.

Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level), complete all as specified.

M&L Hardcore of broken bricks of gauge not exc 63mm, deposited spread and leveled in layers not exc 15 cm thick watered and rammed to true surface, complete all as specified.

Demolition of un-reinforced cement concrete of any description and in any position, complete all as specified.

M&L for 15 mm in cement mortar (1:4) brick/concrete surfaces for Sunken floors, mixed with using WPC @ 100grm per 50 kg bag, add with 23 ltr of water and all as specified and directed by Engr-in-Charge. (WPC shall be measured and paid seaparately).

M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces, complete all as specified.

M&L PCC (1:5:10) type E-2 (40 mm graded stone aggregate) as in filling under sunken floors, complete all as specified.

M&L for 25mm thick PCC (1:2:4) type B-1 using 20mm graded stone aggregate for floor finish without using extra cement, complete all as specified.

S&F Galvanised iron steel water tubing, 40mm bore, light grade with all fittings and fixed to walls and ceilings or laid in floors/sunken floors as spout, complete all as specified.

M&L for Cement concrete (1:3:6) type C-1 using 20 mm graded stone aggregate as in 50mm thick plinth protection, surfaces finished even and fair without using extra cement, including provision of construction joints, complete all as specified and directed

M&L Cement concrete (1:2:4) type B-1 (20 mm graded stone aggregate) as in filling of steel chowkhats and bed blocks of hold fast including necessary formwork, complete all as specified.

M&L Complete removal of existing treatment and preparation of old plastered surfaces of walls and applying one coat of cement base paint over a coat of primer, complete all as specified.

M&L Complete removal of existing treatment and preparation of old plastered surfaces of walls and applying and applying two coats of oil bound distemper, over a coat of 2 mm thick wall care putty, complete all as specified and as directed.

M&L Preparation of old decorated plastered or unplastered by applying one coats of white wash on ceiling including cornices, pillasters etc complete all as specified and as directed.

M&L Preparation of newly plastered surfaces and applying two coats of oil bound distemper, over a coat of 2 mm thick wall care putty, and a coat of primer, complete all as specified and as directed.

M&L Preparation of new plastered surfaces walls etc and applying two coats of cement base paint over a coat of primer, complete all as specified.

M&L Preparation of newly plastered surfaces of walls & applying two coats of white wash, complete all as specified.

M&L Preparation of newly plastered surfaces of ceiling & applying three coats of white wash, complete all as specified.

M&L Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint, complete all as specified.

M&L Preparation of old treated steel surfaces of any description, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

M&L Preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified.

M&L Preparation of old treated wooden surfaces of any description, over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified.

M&L for prepration of old painted plastered surfaces of any description over 10cm girth or width, not otherwise describe and applying one coat of synthetic enamel (one tint) paint, complete all as specified.

M&L for writing letters or figures (Block, Roman, Italic or Indian) n. exc 30cm high with synthetic enamel paint including cleaning and preparation of surfaces complete all as specfied and directed.

Demolition of reinforced cement concrete in any position, complete all as specified.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as directed by Engr-in-Charge

M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm complete all as specified and directed by Engr-in-Charge

S&F Mild steel TMT bars 5 mm to 10mm dia cut to length, bent to shape required including cranking, bending spirally for columns, hooking ends, as in stirrups,spacers, binders and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete, FE-500/550 confirming to IS-1786-1985 all as specified & directed.

M&L for reinforced cement concrete type B-1, (1:2:4) (20mm graded aggregate)as in slabs supported on walls, beams and columnsin floors, roofs, landing, balconies, canopies, deck slabsand in shelves etc. complete all as specified and directed.

M&L for 100mm thick Plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base complete all as specified and directed

S&F 60 mm thick (M-35 Grade) factory made, machine pressed,precast cement concrete interlocking paver block any shape with grey cement and pigment, confirming to IS-15658:2006, set and joints grouted in fine sand, laid over and including 25 mm thick layer of sand cushioning, complete all as specified and as directed.

Taking down carefully existing alumimium point wiring for light/fan/socket out let points complete with fitting and fixtures, battens, wire etc and making good the disturbed surfaces of walls and ceilings, complete all as specified.

S&F Point wiring complete with 1100 volts grade PVC FRLS insulated unsheathed cable of copper conductor, multi stranded of size 1.5 Sqmm, single core, drawn through & including PVC rigid concealed conduit, medium grade of suitable size (not less than 20mm dia )duly ISI marked with all accessories such as bends, reducers, spacers, saddles, junction boxes, bakelite sheets, sizes for mounting switch/sockets, fan regulators etc complete with and including continuous earth wire of size 1.5 Sqmm, single core, PVC FRLS copper conductor, insulated, unsheathed,stranded (Green colour) connected to common earth dolly complete all as specified for following :- (a) One light/fan point/bell controlled by one single pole one way switch.

(b) One 3 pin 5 Amp socket outlet point controlled by one switch on same board.

(c) One 3 pin 5 Amp socket outlet point controlled by one switch on Independent board .

S&F Switch, piano, flush type, single pole one way, 5 Amps, ISI marked, complete all as specified.

S&F Switch piano flush button type 15 Amps, single pole, one way, ISI marked, complete all as specified.

S&F Socket outlet,2 in 1, 5 pin ,5 Amp, piano flush type, ISI marked, complete all as specified.

S&F Socket outlet 2 in 1, 6 pin,5 Amp and 15 Amp, piano flush type, ISI marked, complete all as specified.

S&F Bell push, flush type, 5 amp complete all as specified.

S&F Ceiling rose, surface type, backelite 65mmx50mm, 3 terminals, complete all as specified.

S&F Lamp holder, insulated body, threaded dome pattern, suitable for bracket/batten fittings, complete all as specified.

S&F LED bulb 10 watts suitable for fixing in lamp holder, complete all as specified.

S&F bell Ding Dong AC 230 volts, single pole, complete all as specified.

S&F in repairs stepped type electronic fan regulator for ceiling fan 1200/1400mm size,230 volts,6 Amps, complete all as specified.

S&F in repair Factory made sheet metal enclosures double door type made out of CRCA 1.2 mm thick M.S sheet, powder coated, concealed in wall, TPN DB with 200 Amps rated bus bar, 4 way, 415 volts, vertical type, dust and vermin proof,suitable for incorporation of MCBs duly concealled in wall, factory made,including making good distrubbed surfaces with matching colour, complete all as specified.

S&F Factory made sheet metal enclosures double door type made out of CRCA 1.2 mm thick M.S sheet,powder coated, SPN DB with 200 Amps rated bus bar, 8 way, FP-42 protection surface mounting, 240 volts, dust and vermin proof, suitable for incorporation of MCCBs duly concealled in wall, factory made,including making good distrubbed surfaces with matching colour, complete all as specified.

S&F of MCCB Thermal based release adjustable type 4 pole 63 Amps 50 HZ 415 Volts with rupturing capacity 16 KA including testing, complete all as specified and as directed.

S&F in repairs MCB, single pole, 240 Volt, 32 Amps,10 KA 'B' series, complete all as specified.

S&F in repairs MCB, SPN, 40 Amps, 240 volts 6 to 32 Amps10 KA 'B' series, complete all as specified.

S&F in repair of regular batten for LED tube 20W, 4 feet long indoor decorative batten with extruded aluminium housing & Opal diffuser energy efficient 230 Volts IP-20 fixed to walls/ceiling etc, complete all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size, complete all as specified..

S&F in repairs for sub main wiring with two single core PVC insulated unsheathed stranded copper conductor cable FRLS 2x6 Sqmm single core 650/1100 V , drawn through & including rigid PVC non metallic concealed conduit 25 mm dia including continuous earth wire of size 1x6 sqmm, PVC insulated and unsheathed cable copper stranded conductor (green colour) complete all as specified. NOTE:-Two runs of cable,1 run of earth wire & one run of PVC conduit shall be measured as one length.

M& L Earthing as in repairs complete, all as shown on electrical plate No 3 of MES schedule part-I, as in repairs and as specified including the following :-(i) Galvanised steel earth plate of size 60cmx60cmx6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth not less than 1.50 metre below normal ground level.(ii) Earth plate surrounded by and packed with char-coal and common salt in alternative layers (n.exc 15cms each layer).(iii) 4 mm dia (8 SWG) G.I earth wire from earth plate to main switch board including necessary GI bolts, nuts check nuts, washers, thimbles etc.(iv) 15 mm bore light grade, GI pipe for protection to earth-strip.(v) 20mm bore, medium grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horizontally to the earth pit. (vi) 50mm thick pre-cast cover of cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate and MS angle iron 25x25x3mm frame including two coats of painting over a coat of red oxide to exposed steel surfaces.(vii) Excavation in soft/loose soil, returning filling & removal of surplus soil to a distance upto 50 metre as directed.

Supply & Fixing LED Bldg security light 40 watts lens type, pressure die cast aluminium housing, heat resistane toughened glass with frame, IP 66 protection with bracket (for housing street light fittings) made of GI pipe 40 mm dia light grade 1.0 mtrs long duly cutted and welded at an angle of 120 degree and fixed to wall with 50 mm X 6 mm MS clamps - 02 Nos with 16 mm dia bolts, nuts, and washers, complete all as specified and directed.

S&F as in repairs XLPE insulated, armoured,1100 volts grade, heavy duty cable of size 25 Sqmm nominal cross section, 4 core, flat or circular, PVC FRLS insulated aluminium conductor, served with inner sheathing of galvanized steel wire or tape and over-all PVC FRLS sheathed in service connections, laid in trenches, duct, through pipe, in floor, on pole including jointing and testing, complete all as specified .

Excavation in trenches in soft/loose soil not exceeding 1.5 metre wide and not exceeding 1.5 metre deep and not exc 10 Sqm on plan,for laying of cable and getting out,compete all as specified.

Returning, filling in, earth including spreading, leveling watering and well ramming in layers each not exceeding 25cm thick each layer, complete all as specified.

Removal of surplus soil to a distance not exc. 50 metre and depositing where directed at a level not exc. 1.5 metre above the starting point complete all as specified.

M&L Dry and clean fine sand for cable cushioning to underground cable protection, complete all as specified. (Excavation and earth work measured separately).Note- Punned down thickness shall be measured.

S&F in repair Cover to underground cable with one layer of bricks using sub class ‘B’ bricks (old size) laid flat across the cable complete all as specified. (Excavation and earth work measured separately).

S&F Mild steel galvanised pipe, light grade, 40 mm nominal bore for passing of cable, fixed to poles/laid under floor/road crossing/walls complete with and including clamps socket & elbow etc complete all as specified.

M/S KRISHNA ENTERPRISES

M/s Bansi Lal

M/S Yashpaul Gulati

R.S.ENTERPRISES

M/s Mukand Lal Khanna

Niraj Kamal Sharma